Академический Документы
Профессиональный Документы
Культура Документы
ELP/EMP-7200
EPSON
INTRODUCTION
This Service Manual describes of the hardware information which is necessary for the smooth repair and technical support of the XGA DATA PROJECTOR ELP/EMP-7200 and the trouble shooting. The primary technologies will be supplied with Technical Information hereafter.
TRADEMARK
IBM and DOS/V are the trademark or the registered trademark of International Business Machines Corporation. Macintosh and Power Book are the registered trademarks of Apple Computer Inc. Windows is the trademark of Microsoft Corporation. EPSON is the trademark of SEIKO EPSON CORPORATION. NOTICES
1. This document should not be reproduced in whole or in part without the written permission of SEIKO EPSON CORPORATION. 2. Any of description in this document is the subject to change without notice in future. 3. The information and specification in this document are the most up-to-date at the time of publication. However, we are unable to guarantee the accuracy of printed material after the date of publication. In case of any mistake or lack of description, please kindly notify us to correct. 4. Any influence by utilizing the document may be out of our responsibility regardless the item 3 above.
1998
REV.A
Record of Revisions
History REV-A Issued Date 1998, November. 27 Alternation Preliminary Issued
Memo Random
Free area to memorize any important technical information here.
REV.A
PRECAUTIONS
1. MAINTAIN THE SAFETY OF OPERATORS
(1) PROTECTION FROM ELECTRIC SHOCK * Whenever doing any repair work on the product, be sure to turn off the power switch and remove the electric power cable from the electrical outlet. * Whenever inevitably turning the power on to the product opening the case or cover (repair process) be sure to take off any metallic materials such as watch, cuffs, rings, and tie pins which may touch the metallic part of the product and dangerous of electric shock. (2) PROTECTION FROM ACCIDENTAL INJURY * Be sure not to touch the lamp inner housing and its circumstances after the power is turned off, they may be heated up even after the cooling down process was ended. Also make sure not to touch the light source and its circumstances during the operation of repair as turning the power on. * Make sure to protect your hands by gloves from sharp edges during assembly and disassembly. * Do not look into the light source or lens while the light is on. Protect eyes from being damaged. (3) PROTECTION FROM ACCIDENTS * Any operation should be done while the device placed on a flat and stable place to prevent the device or parts from being dropped. Be careful not to place tools and parts on the device or at your feet. * Whenever doing any repair work on the product, be sure to away from a place for foreigner come across in order to prevent the product from being used in incomplete condition or accidental near miss. Be sure not to leave the product during any repair work. * Be sure to use the attached power cable when you supply the power to the product.
REV.A
2. SAFETY MAINTENANCE
(1) ELECTROSTATIC DISCHARGE * Whenever doing any repair work on the product, be sure to wear the wristband and the electrostatic mat with grounding. When replacing any electric components (Board and Optical engine), it is recommended to touch the electrostatic plastic bag of the component to the metallic part of the product once before take the component out from the plastic bag. (2) LIMITATION OF PARTS * Use only authorized or supplied parts from EPSON for the replacement of mechanical parts including the lamp inner housing, air filter and so on. * Use only the power cable and the interface cables attached with the product. (3) Others * Visually checks the distortion or dirt at the connectors of the power cable. If dirty, clean off, and if distorted, replace the cable in order to avoid firing by the flush over phenomenon. * When plug the internal connector cables or the interface cables, be sure to fully plug into the connectors unit until it stack to the connector edge. * Whenever doing removal of parts or repair work on the product, make sure that the work is done in a clean room, free of dust and dirt in order to keep the optical element away from dirt.
4. OTHERS
* Any questions on the ELP/EMP-7200's service including supply of the service parts or contents of the document would like to be contacted to the below address. Any technical information about amendments is occasionally available as Technical Information.
SEIKO EPSON CORPORATION ADDRESS; 4897 OH-AZA SIMAUCHI,MATSUMOTO-SHI, NAGANO-KEN, 390-8640 JAPAN TEL: +81-263-48-5437 FAX: +81-263-48-5680 ATTN: VD Customer Support Group
REV.A
APPENDIX
A-1. COM IO Software Manual..................................................................... A-2. Firmware Downloader Manual .............................................................. A-3. Part List ................................................................................................ A-4. Exploded Diagrams .............................................................................. A-5 Kinds of Screw Name List......................................................................
REV.A
Part name Optical engine Light Valve R Light Valve G Light Valve B Logotype Plate Rating Label JAN Code Label Serial No. Label A Master Carton
Remarks involving Light Valve No Micro Lens Allay ditto ditto Indicated name of ELP/EMP-7200. Indicated name of ELP/EMP-7200. ditto ditto Indicated name of ELP/EMP-7200.
The Light Valves are incorporated in the optical engine. The Optical engine is to be supplied as one unit. Expensive adjustment equipment is required to repair the internal optical engine so that such items are to be repaired at the exclusive factory in Japan.
REV.A 1-1
Capable OS
Language of software
New Projector Software ELP Link III V2.0 CD-ROM ELP/EMP-3500, 5000, 7000, 7300 ELP/EMP-5100, 5300, 5500, 7100, 7200 Windows3.1 Windows95, 98 Windows NT 3.51, 4.0 Mac KANJI Talk 7.5 and the latter version Mac System 7.5 and the latter version Japanese, English German, French, Italian, Spanish and Portuguese
Old ELP Link III Set ELP Link III V1.0 Floppy Disk ELP/EMP-3500, 5000, 7000, 7300
Windows3.1 Windows95 Windows NT 3.51, 4.0 Mac KANJI Talk 7.1 and the latter version Mac System ver.7 and the latter version Japanese, English
1.2.3 ESC/VP
ESC/VP (Epson Standard Code for Visual Products) is prepared as a command system for controlling projector via computer. Each level command is basically upper compatible. However the commands which correspond to the projector hardware function are exclusive commands for each model. The capable projectors for each level are as follows:
Table 1-3. Interchangeability list for ESC/VP Level
REV.A 1-2
Optical method Projection image size Projection distance Resolution Projection Lens Focus adjustment Zooming adjustment Light Source Life (Lamp inner housing) Average luminance AUDIO FEATURES Output for internal speaker Audio out Interface
Poly-silicon 1.3" TFT Poly-silicon 1.3" TFT (MLA (without MLA) color liquid built) color liquid crystal crystal display (R/G/B three display (R/G/B three panels) panels) Full lines, six phase block Full lines, six phase block series series Dichroic mirror separation and prism combine method Minimum 23 inch to maximum 300 inch 1.2m 16.7m 786,432 pixels (1024 x 768 dots) x 3 sheets Zoom lens F2.0 - 2.3, f:55-72 mm Manual Manual (1:1.3) 120 W (AC drive) UHE (Ultra High Efficiency) lamp, (type: ELPLP05) 2000 hours at 50% brightness or 50% motality) 1000 ANSI lumen 1200 ANSI lumen (Catalogue spec.) (Catalogue spec.) Dynamic speaker (3W-8 ) x 2 (stereo) 50 to 18,000 Hz External speaker 3.5 mm Stereo mini-jack Internal speaker output is stopped when mini-jack is plugged. Output signal: 0 to 500 mVrms Load impedance: 600 Audio signal (stereo) from the video devices is separated with R (Right) and L (Left). Interface type: RCA jack Input signal: 500 mVrms Host computer 1 Audio input (stereo) Interface type: 3.5 mm Stereo mini-jack Input signal: 500 mVrms/47 K Host computer 2 Audio input (stereo) Interface type: 3.5 mm Stereo mini-jack Input signal: 500 mVrms/47 K For controlling ELP/EMP-7200 operating mode and controlling host computer from ELP/EMP-7200. Signal is detected with internal receptor board. Control range: Within 10 m and 30 degree wide (right/left), 15 degree wide (upper/ lower) from receptor of LCP. When connecting 3.5 mm stereo mini-jack cable, external receptor of remote controller is available. (On plugging internal receptor being off.) Having conformity to Xantech "REMOTE IN" system
Audio 1 interface (For Computer 1) Audio 2 interface (For Computer 2) REMOTE CONTROL Wireless remote controller
REV.A 1-3
Description COMPUTER IMAGE SIGAL INPUT/OUTPUT Capable computer mode [Refer to Table 1-5 and 1-6] PC Image Signal Input terminal 1, 2 Output terminal Input/ Output Signal
ELP/EMP-7200
ELP/EMP-7300
PC98, EGA, VGA, VESA 72/75/85, SVGA 56/60/72/75/85, XGA 60/70/75/85 MAC 13/16/19/21, SXGA60/70/75/85/43I Form:HD-15Pin (adaptive to DDC1/2B ) Form: HD-15Pin Analogue RGB Standard Input level 0.7Vp-p, 75 Mac 0.7141 Vpp, 75 (Analogue RGB adoptive Input level 0.5 to 1.0 Vpp, 75 ) Separate/Composite/Sync. On Green are capable Separate Sync.: Positive & Negative 1 to 5 Vp-p Composite Sync.: Positive & Negative 1 to 5 Vp-p Sync. On Green: Sync.- Negative 0.3 Vp-p This terminal combines color difference signal input terminal as well. OSD Menu makes shifting. (Default: RGB Input) Form: BNC Display: R. G/G Sync.: B:HD/Sync.: VD Analogue RGB Input level 0.7 Vp-p, 75 Separate Sync., Composite Sync. Or Sync. On. Green: Sync.-Negative 0.3Vp-p NTSC3.58, NTSC4.43, PAL, N-PAL, M-PAL, SECAM Automatical discrimination (Fixed use is available.) Form: Mini DIN 4Pin Luminance 0.714 Vp-p, Chrominance 0.284 Vp-p 75 S Video has priority over Composite Video.
Sync. Signal
Input Signal
TV IMAGE SIGNAL INPUT TV Signal Method [Refer to table 1-7] S Video Input Input terminal Input signal
Composite Video Input Input terminal Form: RCA Jack (Yellow) Input Signal 1.0 Vp-p Sync.-Negative, 75 Color Difference Signal (R-Y, Y, B-Y) Input Input terminal This terminal combines RGB Video Input terminal as well. OSD Menu makes shifting. (Default: RGB Input) Form: BNC Display: Y (owned jointly with Video In G Jack):R-Y (jointly with Video In B Jack): B-Y (jointly with Video In R Jack) Input Signal Analogue RGB Standard Input level 0.7 Vp-p, 75 Sync.-Negative (0.3V) MOUSE/COM 1/2 Mouse and Serial Communication Automatically discrimination of Mouse (PS/2, Serial, ADB, 98 Bus), Serial Communication (RS-232C) Interface type: DIN 13pin
REV.A 1-4
Description
POWER SUPPLY & Others Input Voltage Power Consumption
ELP/EMP-7200
ELP/EMP-7300
Dimentsions
Weight
300 mm (W) x 120 mm (H) x 363 mm (D) 300 mm (W) x 129 mm (H) x 400 mm (D) include foot adjuster and lens Approx. 6.7 kg
EMVIRONMENT Operation/storage temperature +5C to +40C/ -10C to +60C (non condensing) Operation/storage humidity 20% to 80%/ 10% to 90% (non condensing) Operation/storage or carriage Altitude 3048m/ 6096m
REV.A 1-5
No
Format
Timing
No
1 NECPC400 2 NECPC750 3 EGA 4 VGAEGA 5 VGA_Text 6 640x350 @85 7 640x400 @85 8 720x400 @85 9 VGA60 10 VESA72 11 VESA75 12 VGA75 13 VESA85 14 SVGA56 15 SVGA60 16 SVGA72 17 SVGA75 18 SVGA85 19 XGA43i 20 XGA60 21 XGA70A 22 XGA70B 23 XGA75 24 XGA76 25 XGA85 94 97 23 100 24 89 90 96 28 29 95 91 98 103 4 99 5 93 64 65 25
Timing Name
Original Standard #
Notes
NECPC400 640 x 400@56Hz NECPC750 1120 x 750@40Hz DMT648A 640 x 350@85Hz 640 x 350@70Hz VGA_m2 720 x 400@70Hz 640 x 350@85Hz 640 x 400@85Hz 720 x 400@85Hz VGA_m3 DMT6475 XGA6475 DMT6485 640 x 480@60Hz 640 x 480@75Hz 640 x 480@75Hz 640 x 480@85Hz VS901101 640 x 480@72Hz
Windows95 Start UP 832 VESA Support 832 936 800 832 840 800 832 VESA Support Standard Signal Standard Signal
VG900601 800 x 600@56Hz VG900600 800 x 600@60Hz 2 VS900603 800 x 600@72Hz DMT8075 DMT8085 VGA_m4 800 x 600@75Hz 800 x 600@85Hz 1024 x 768@43Hz
35.16 56.25 1024 37.88 60.32 1056 48.08 72.19 1040 46.86 75.00 1056 53.67 85.06 1048 35.52 86.96 632 48.36 60.00 1344 56.48 70.07 1328 56.29 70.01 1368
VG901101 1024 x 768@60Hz VS910801 1024 x 768@70Hz XGA_m5 DMT1075 XGA1076 DMT1085 1024 x 768@70Hz 1024 x 768@75Hz 1024 x 768@76Hz 1024 x 768@85Hz
60.02 75.03 1312 VESA Support Standard Signal 61.08 75.78 1408 68.68 85.00 1376 VESA Support Standard Signal
REV.A 1-6
No
Format
Timing
No
26 EWS70 27 EWS75A 28 EWS85 29 EWS60 30 EWS75B 31 SXGA43i 32 SXGA60 33 SXGA75 34 MAC13 35 MAC16 36 MAC19 37 MAC1960 38 MAC21 6 7 8 11 13 9 10 12 54 58 59 60 61
Timing Name
DMT1170 DMT1175 DMT1185 DMT126A DMT127A DMT1243 DMT1260 DMT1275
Original Standard #
1152 x 864@70Hz 1152 x 864@75Hz 1152 x 864@85Hz 1280 x 960@60Hz 1280 x 960@75Hz 1280 x 1024@43Hz 1280 x 1024@60Hz 1280 x 1024@75Hz
Notes
67.50 75.00 1600 VESA Support Standard Signal 77.09 85.00 1576 60.00 60.00 1800 VESA Support Standard Signal 75.00 75.00 1680 46.43 86.87 1 63.98 60.02 1688 VESA Support Standard Signal 79.98 75.03 1688 VESA Support Standard Signal 35.00 66.67 864 848
49.11 75.09 1120 60.24 74.93 1328 48.19 59.28 1328 68.68 75.06 1456
REV.A 1-7
Table 1-6. List of the PC Signals not formally supported (Common to ELP/EMP-7300 and 7200)
The following signals are not supported formally but they are available on ELP/EMP7300 and 7200. Notes V Trac Original H No Format Timing Timing Name Standard # Freq. Freq. king No [kHz] [Hz]
1 VGA256 2 VGACGA 3 MACLC_13 4 MAC12 5 DMT128A 6 HP1272 7 HP1275 8 IBM60 9 IBM67 10 SON1274 11 SUN1061 12 SUN1166 13 SUN1176 14 SUN1267 15 SUN1276 16 SGI_1272 17 INT1160 18 DMT1243_R 47 55 51 15 41 42 44 45 75 77 79 81 83 85 MAC_13LC MAC_12C DMT128A HP1272 HP1275 IBM6Km2 IBM6Km3 SON1274 SUN1061 SUN1166 SUN1176 SUN1267 SUN1276 SGI_1272 INT1160 DMT1243_R 640 x 400@70Hz 640 x 200@70Hz 640 x 480@67Hz 512 x 384@60Hz 1280 x 960@85Hz 1280 x 1024@72Hz 1280 x 1024@75Hz 1280 x 1024@60Hz 1280 x 1024@67Hz 1280 x 1024@74Hz 1280 x 1024@61Hz 1152 x 900@66Hz 1152 x 900@76Hz 1280 x 1024@67Hz 1280 x 1024@74Hz 1280 x 1024@72Hz 1184 x 884@60Hz 1280 x 1024@43Hz 31.46 70.00 31.46 70.00 34.98 66.62 24.48 60.15 800 800 896 640
85.94 85.00 1728 78.12 72.01 1728 80.00 75.03 1688 63.36 60.00 1760 70.76 67.00 1696 78.86 74.11 1712 65.27 61.40 1424 61.80 65.95 1504 71.71 76.05 1472 71.72 66.72 1632 81.13 76.11 1664 76.92 72.20 1690 52.20 60.00 1504 46.43 86.87 848
REV.A 1-8
TV Mode
NTSC3.58 (M-NTSC) PAL (B/G/H/I-PAL) SECAM NTSC 4.43 N-PAL M-PAL PAL-60
Remarks
50 60 50 60 60
General NTSC (Japan, USA and others) General PAL (Europe, South East Asia and others) *1 (France, East Europe and others) *2 (Argentine, Uruguay, Bolivia) (Brazil) *2
[Additional explanation] On air method is shown with Color method-NTSC/PAL/SECAM and broadcasting standard-N/M/B/G. *1 SECAM has "L" and "B/G/H" methods. These ones vary each other in respect of polarity of horizontal sync. signal and voice modulation method. *2 NTSC4.43 and PAL60 are what are output when NTSC software is reproduced on VCR of PAL spec. Then the NTSC data is to be output in PAL spec. NTSC4.43 has transmission method of NTSC and the carrier frequency is 4.43MHz as well as PAL. PAL60 has transmission method of PAL and the vertical frequency is 60Hz as well as NTSC. Either ones have source of M-NTSC so that they have 525 pcs of scanning line for each.
REV.A 1-9
! " "
#
$%&'$
!
( )*
& * + ,
%+
'()*+,-./ 2
67 3"
! " 0122
8 9 : 8 : 0 45 3#5
# #
$%&%%
REV.A
1-10
Appendix
A-3. After Service Parts List for EMP/ELP-7300, 5300, 7200 A-4. Exploded Diagram for EMP/ELP-7300, 5300, 7200 A-5 Screw Name List
(6) (7)
Open necessary command in the "Transmit List" and execute the item by transmitting. The commands included in the Transmit List are always to be executed. In case of executing any new commands, please surely execute it after eliminating the former command with pressing "Delete(D)" button.
SEIKO EPSON
LP-3500/ E MP-3500) 3. Measuring the detailed data of lamp timer (except E 3-1. Execution of command (1) Press "Open(O)" button. (2) Select "LT_Count.txt" file. (3) Open the "LT_Count.txt" file. (4) Command (1), (2) and (3) are indicated on the "Transmit List". (5) Press "Transmit(C)" button. (6) The "Receive List" is indicated. (1) ACK (2) ACK 1B0A02080001200025A6 (3) ACK 3-2. The theory of lamp timer counting (1) Time is indicated at (2)ACK in the "Receive List" mentioned in 3-1. (6). (2) Disregard 2 figures from the right end. (3) The 4 figures, which are from 3rd figure to 6th figure with counting from the right end, do indicate hour. (*counted by hexadecimal) ex) 25 (16) = 37 hour (4) The 4 figures, which are from 7th figure to 10th figure with counting from the right end, do indicate second. (*counted by hexadecimal) ex) 120 (16) = 288 seconds = 4 minutes 48 seconds 4.
SEIKO EPSON
4.3 for EMP/ELP-5500, 7500 (1) Press the Power button to turn off the projector, (2) When the projector is in sleep mode, you can execute "com io" software. (3) Press "Open(O)" button. (4) Select "55LT_reset.txt" file. (5) Open the "55LT_reset.txt" file. (6) Command (1), (2) and (3) are indicated on the "Transmit List". (7) Press "Transmit(C)" button. (8) The following "Receive List" is indicated. (1) ACK (2) ACK (3) ACK (9)Turn off the power switch on the back of the projector. 5. Reversing right side left (1) Press "Open(O)" button. (2) Select "RearProj. txt" file. (3) Open "RearProj. txt" file (4) Command (1) is indicated on "Transmit List". (5) Press "Transmit(C)" button. (6) "Receive List" is indicated. Indication; (1) ACK Resetting the reversal (common for E LP-3500, 5000 and 7000) (1) Press "Open(O)" button. (2) Select "RearReset. txt" file. (3) Open "RearReset. txt" file. (4) Command (1) is indicated on "Transmit List". (5) Press "transmit(C)" button. (6) "Receive List" is indicated. Indication; (1) ACK (O nly for E MP-7000)
6.
7. Setting TV signal into PALspec. (Non Interlace double scanning method) (Refer to Technical Information No. 97-05) (1) Press "Open(O)" button. (2) Select "7000PAL. txt" file. (3) Open "7000PAL. txt" file (4) Command (1) , (2), (3) and (4) are indicated on "Transmit List". (5) Press "Transmit(C)" button. (6) "Receive List" is indicated. (O nly for E MP-7000) 8. Setting TV signal into NTSCspec. (Interlace method) (Refer to Technical Information No. 97-05) (1) Press "Open(O)" button. (2) Select "7000NTSC. txt" file. (3) Open "7000NTSC. txt" file (4) Command (1) , (2), (3) and (4) are indicated on "Transmit List". (5) Press "Transmit(C)" button. (6) "Receive List" is indicated. Com IO MANUAL Ver1.1 Ver1.5 Issued Date: Issued Date:
SEIKO EPSON
1/2
Outline of software
This software has been made in order to set up and version up software of the Multi media projector, EMP-7300/5300/7200 through PC. The firmware mentioned here means a generic name of the program installed in the flash ROM of projector and it is such software as made for the purpose of controlling EMP-7300/5300/7200.
SEIKO EPSON
D_Loa dm E .doc
2/2
Close Button
5.3
Press Down Load button and carry out download. Then progress status of communication is displayed at the bottom of screen. 5.4 If message of communication end is displayed, press Close button and finish the software.
DownLoader MANUAL
Issued on June 2. 1998 Issued on Sep. 30. 1998 Issued on Nov. 12, 1998
ELP-7300/5300/7200 After Service Parts List NO 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 DESCRIPTION Lower Case Unit Lamp Cover Air Filter Cover Mini Cramp Foot Unit Foot Lever L Foot Lever R Screw Screw Optical Engine Lamp Inner Housing Intake Fan Air Filter B Filter Flame B Screw Board Spacer Zoom Ring Focus Ring Screw Power Supply Block Power Supply Unit Ballast Board Assembly Screw Receptor Board Assembly A Receptor Cable Screw Speaker L Screw Screw Screw Audio Speaker Unit Audio Speaker Fixing Plate Speaker R Screw Audio Board Assembly Screw Spring Radiation Sheet
SPECIFICATION
1/3
3x15,F/Zn 4x14,F/Zn
3x25,F/Zn
2x4,F/Ni
3x6,F/Ni
3x6,F/Ni 3x6,F/Ni
ELP-7300/5300/7200 After Service Parts List NO 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 DESCRIPTION Shield Gusket Screw Rear Case Unit V Rear Case Exhaust Fan Exhaust Fan Cushion Screw Clip IF Unit PC-IF Screw Video-IF Screw Screw Main Board Assembly Screw Clip Cable Assembly AJ-AU Cable Assembly MJ-MA Cable Assembly PJ-MA3 Cable Assembly PJ-MA8 Cable Assembly VJ-AJ-MA Cable Assembly VJ-MA Cable Assembly MA-AU Cable Assembly Lamp-Fuse Safety Switch Thermo Sensor .Lamp Thermo Sensor .L/V Thermo Sensor .OA Mini Cramp B Screw Screw Handle Clip Nat Upper Case Unit Operation Panel Spring Operation Panel Screw Screw
SPECIFICATION
2/3
3x6,F/Ni
3x30,F/Zn
3x12,F/Zn 2.5x5,F/Zn
4x9,F/ZB 4x14,F/Zn
ELP-7300/5300/7200 After Service Parts List NO 77 78 79 80 81 DESCRIPTION Inter Face Panel V Screw Front Foot Rubber Unit Lens Cap Logotype Plate Carton Box Set Reinforcement Pad Lower Pad Upper Pad Accessory Box Accessory Holder Polyvinyl Bag Soft Bag Slip Sheet UPC Code Label Caution Label A (Lamp Exchange) Caution Label B (Don't Look) Caution Label C (Don't Open) User's Manual Set Seal Set AC Power Cable A.V.Cable Remote Controller Mac Adopter Set Computer Cable Audio Cable ELP Communication Kit Main Cable PS/2 Mouse Cable Serial Mouse Cable Mac Mouse Cable Serial Cable Mac Serial Cable Projector Software
SPECIFICATION
3/3
2.5x6,F/ZB
72. Upper Case Unit 51. Screw [CBP-tite 3x8] 70. Handle 52. Main Board Assembly
76. Screw [CBB-tite 4x14] 20. Power Supply Block 40. Screw [CP(o) 3x6] 29. Screw [CCP-tite 3x10] 9. Screw [CBB-tite 4x14] 30. Screw [ CBP-tite 3x8] 41. Rear Case Unit V
31. Audio Speaker Unit 68. Screw [CBP-tite 3x12 ] 10. Optical Engine
26. Screw 45. Screw [CBP-tite 3x30] [CP(o) 3x6] 24. Receptor Board Assembly A 80. Lens Cap 6. Foot Lever L 19. Screw [CPB-tite 2x4] 11. Lamp Inner Housing 75. Screw [CB 4x9] 42. Rear Case 81. Logotype Plate 78. Screw [CP 3x6] 4. Mini Cramp 77. Inter Face Panel V 33. Speaker R 5. Foot Unit 4. 43. Exhaust Fan 34. Screw [ CP(o) 3x6] 39. Shield Gasket 36. Screw [CP(o) 3x6] 35. Audio Board Assembly
50. Screw [CP(o) 3x6] 49. Video-IF 48. Screw [CP(o) 3x6]
38. Radiation Sheet 37. Spring 32. Audio Speaker Fixing Plate
1.12
VDCS Group
Screw Name
Terms CB CBB-tite CBP-tite CCP-tite CP CP(S-P1) Names (Japanese) + +,B +,P +
,P +
+
,s2w1 +
,s2w2 +
,B 6,s2 Names Cross-recessed Bind head screw Cross-recessed Bind head B-tite self-tapping screw Cross-recessed Bind head P-tite self-tapping screw Cross-recessed Cup head P-tite self-tapping screw Cross-recessed Pan head screw Cross-recessed Pan head screw with spring washer and plain washer CP(S-P2) Cross-recessed Pan head screw with spring washer and plain washer CP(O) Cross-recessed Pan head screw with outside toothed lock washer HSH Hexagon Socket Head screw
Screw Types
Head (top) C (Cross-recessed) Head (side) B (Bind) Body B-tite Washer (assembled) (O)
C (Cup)
P-tite
(S-P1)
P (Pan)
screwnam.doc