Академический Документы
Профессиональный Документы
Культура Документы
FUNDAMENTALS OF PATTERNMAKING
FOR
WOMEN'S APPAREL
BOOK 2
STYLE PATTERNS
by
ESTHER KAPLAN
nvmcx
F U N D A M E N TA L S
OF
PATTERNMAKING
FOR
WOMEN'S
APPAREL
BOOK
II
STYLE
PATTERNS
by
Esther
Kaplan
Pivnick
T1453o
Book II uses the foundation patterns to make the most important and basic types of styl e patterns. There can be m a n y s ty le variations, but only a few basic ways a piece of material can be cut into to m a k e a style, from the patternmaker's point of view. Collars will have one type of roll or another; a sleeve can be handled only in certain basic ' w a y s ; the procedure for making gathers is the same whether f o r a waist, a skirt or a sleeve. The principles of cutting underlying these basic types is the concern here. They have been kept as general and flexible as possible, suitable for all types of garments in all size ranges. Rigid measurements have been avoided as unnecessary. The relationships between the instructions for the various parts of the garment have been carefully
noted.
The book has been laid out with a de nite order in mind for learning. One problem develops from another, and so each section should be followed in its sequence for be s t r e s u l t s . Each problem should be c a r e f u l l y worked o u t exactly as presented, at first. The patterns should be cut out in s o m e kind of tting cloth such as unbleached muslin, and pinned or basted together. They can then be tried on the dress form or the person from which the foundation patterns were made. Changes and corrections can be made in the muslin t t i n g and transferred back to the paper pattern.
Later, a f t e r the basic principles involved are clear, the completion of the style lines can be l e f t to the cloth tting. A sort of combination of "flat" patternmaking and draping can be used.
There is no need in my opinion for any argument about draping versus "flat" patternmaking. Both make patterns. In each case, the patterns are based on the same principles. Since the principles work out automatically in " a t patternmaking, the beginner can achieve b e t t e r r e s u l t s by starting his learning with the handling of paper foundation patterns. He can then b e t t e r apply his understanding to working with fabrics on a dress form if he wishes. The more advanced worker can produce his effects more quickl y . There is no clear l i n e separating the two. I, in my own work as a patternmaker and an assistant designer have constantly combined the two methods. I have used the foundation patterns to block out swiftly, d i r e c t l y in the muslin if possible, the important construction lines, such as the shifting of the bust dart to some style l i n e , the type of r o l l f o r the c o l lar neckline, the basic shape f o r a kimono sleeve, e t c . The muslin w a s then cut with suf c i e n t seam allowances f o r any changes, and tted to the dress form. Working on the dress form I could perfect the shape of my s ty le lines, take care of any change caused by the nature of the fabric, s h i f t fullness a l i t t l e , tighten up a bit where better design seemed to call for i t , e t c . Even then, the pattern, carefully corrected and nished, might undergo l a t e r corrections because of the fabric used for the garment. A n e wool will give d i f ferent results from the s a m e pattern than a slippery rayon. B u t these changes are minor, not affecting the basic construction of the pattern.
Draping shows the learner the signi cance of the grain of the fabric. It permits experimentation with fabric and allows for a sort of three-dimensional sketching. "Flat" patternmaking shows the learner c l e a r l y the relations between the parts of the p a t tern. It makes him appreciate the need for accuracy, f o r a "good l i n e . It teaches him how to maintain the s a m e basic standards of tting no matter what the style variation. It allows h i m to make well-fitted garments t h a t can be m a s s produced with uniform r e s u l t s in t and s t y l e . It permits creativeness based on sound principles.
The tools needed are a sharp p e n c i l , a sharp pair of shears, an accurate ruler, a tape measure, and loads of paper, muslin and patience f o r m u c h practicing. Esther Kaplan Pivnick
February, 1958 Cold Spring Harbor, N. Y.
iii
TABLE
OF
CONTENTS
DARTS
Bust Darts, Back Waist Darts, Yokes
INDEX............................................page
SKIRTS
Yokes, Pleats, Gathers, Flares, Circle Skirts, Godets
INDEX............................................page 31
SLEEVES
Set-In S l e e v e s
Bell Sleeves, Bishop Sleeves, Lantern Sleeves, Special Style Sleeves, Gathered Cap Sleeves, Darted Cap Sleeves, Cowl Sleeves
I N D E X . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . p a . g e 55
Sleeve- W a i s t C o m b i n a t i o n Sleeves
F i t t e d Raglan Type Sleeves, Gusset Kimono Type Sleeves, Non-Gusset Kimono Type Sleeves
I N D E X . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . p a g e 77
INDEX............................_................page 103
APPENDIX
The Two-Piece Sleeve, Cuffs, Pockets, Circular Ruffles, Groups of Pleats, AComplete Dress Pattern and I t s Grading, Grading the TwoPiece Sleeve
'
INDEX............................................page129
3.
vi
INDEX
TO
DART-S
. . . . . . . . . . . . . . . . . . . . . . . . . pages 5-7
Page 5
Page 6
Page 6
Page 8
Page 9
Page 10
. . . . . . . pages
1117
\
Page 11
Page 12
Page 14
Page 15
Page 16
5
W
Page 16
Page 17
. . . .pages 18-24
Page 18
Page 18
Page 19
Page 20
Page 21
Page 22
Page 23
Page 24
DARTS
/
A dart is a seam made by joining the two edges of a triangular section removed to shape a a t piece of cloth so that it covers a round form. The pattern f o r a cone is a good example. The shaded section has been removed. When lines A and B are joined together, the at c i r c l e is forced i n t o a cone shape.
\\A
3/
The dart shows the place where surplus material has been removed to t a piece of c l o t h smoothly to a round form.
@
//
Fitted garments have darts wherever the body is rounded, for example: the b u s t , the hip, and the shoulder blades. A loosely ared or gathered garment provides ample fullness f o r the round parts of the body in its o w n design.
No darts are needed in the gathered bodice since the fullness is more than enough to make room f o r the bust.
//
)1)
/V
In the t t e d bodice the material used to cover the bust is reduced by the two darts to shape it to the size of the waist. (See Book I on draping the f r o n t waist pattern. )
The bust dart has many s ty le uses. The back waist and hip d a r t s are more limited. But the principles involved in the use of a l l the d a r t s is the same. The next two lessons on Bust Darts and Skirts illustrate the basic principles.
The bust dart, as explained in the introduction to Darts, removes the surplus material resulting from tting the roundness of the
bust.
The surplus material need not be removed as one severe dart. It can be divided into m a n y smaller darts, or tucks, or pleats, or gathers, e t c . It can be hidden in s e a m lines.
I
The Figures in this section illustrate a l l the basic uses of the bust d a r t . The possible number of variations is limited only by the designer's imagination.
Figure 1A
This is the basic f r o n t waist pattern with the bust dart at the waistline. (See Book I, The Front Waist Draft, Fig. 9.)
Figure 1B
is
The position of the dart at the waistline convenient for most style uses of the dart. The dart at the side seam can be
equally useful.
The bust dart can be placed in any position on the f r o n t waist p a t t e r n so long as it points to the bust area. the center of the bust (A) or (The dotted line G outlines the average bust area, approximately two inches from the Cen-
to
ter A.)
The dotted lines B, C, D, E, F show the other basic positions: the center front, the neckline, the shoulder, the armhole, and the side seam. The method of shifting the dart from one place to another is the s a m e for a l l positions. The following Figures 2A2.C can be applied to any
position desired.
uh
Shifting T h e P o s i t i o n Of
T h e Bust Dart.
Figures 2A, 2B, 2C show a simple way the dart is shifted to another position; in t h i s illustration, to the shoulder.
Figure 2A
Line D shows the new position of the dart.
Figure 2B
FIGURE 2C. The pieces are placed together again, on another sheet of paper, so that lines A-1 and A-2 meet.
The dart is n o w open at the shoulder. It has been completely removed from the waistline. (The shoulder dart opens wider than the waist dart because the distance from the center of the bust to the shoulder is longer than to the waist.)
L}
Fi g ure 2c
D i v i d i n g T h e Bust Dart.
dart Figures 3A through 31-! show the shifting of the to two positions.
Figure 3A
Figure 3B
Figure 3C
The two parts of the p a t t e r n in Figure 2B can be placed together at Point A so that a dart is opened both at the shoulder and the waistline.
The darts can be shortened if desired by bringing them only to the bust area. instead of to the center point.
The dart space can be divided i n t o two or even more darts if so desired. The darts s t i l l f a l l within the bust area.
The correct shape of the shoulder and waist l i n e s at the darts can be obtained by folding the d a r t s in the paper pattern the way they are folded in cloth and either cutting through or r o l l i n g a tracing wheel through the folded dart.
Figure 3D
Figure 3E
Figure 3F
is
Figure 3 G G
This shows the c l o t h tting of the pattern in Figure 3G. (The pattern should be cut out in muslin or other tting cloth, with seaxns allowed, and basted together for a trial tting. Any desired changes in style or t can be made in the tting and transferred back to the paper pattern, if the paper pattern is the n a l step. Sometimes the corrected muslin is used as a
pattern.)
Figure 3G
This is the same as Figure 3B with the correct shape of the darts at the shoulder and waistline.
Figure 3H
This is the same as Figure 3C with the correct shape of the darts at the shoulder and waist l i n e s .
Figure 3 H H
This shows the cloth tting of the pattern in Figure 3B.
U s i n g T h e B u s t D a r t As
Gather3_
The bust dart shifted to the neckline is used f o r i l l u s t r a t i o n . The bust dart can, of course, be shifted to any place such gathers are desired, in the same manner.
the d a r t as gathers.
Figure 4A
Figure 4B
Figure 4C
FIGURES 4A, 4B, and 4C show the bust dart shifted from the waist to the neckline.
tinuous l i n e f o r gathers from points 3 to 4. The correct the shape can be approximated by adding to one side of other. from the removed has been amount whatever dart A cloth tting should be made f o r n a l adjustment of the shape of the l i n e .
The neckline, when gathered to i t s original size, should have the shape of the original neckline in Figure 4A. If not, it can be redrawn while gathered. When the fabric is opened at again, the corrections can be transferred to the paper pattern.
Figure 4D
FIGURE 4DD shows the cloth tting. The gathers f a l l from the neckline to the bust. The waist area is smoothly t t e d with no d a r t .
Figure 4DD
Figure 4E
Figure 4G
FIGURE 4GG shows the muslin tting of the pattern in Figure 4G.
Figure 4GG
41%
sums LINE
H
G
_\_
\\
\*s~ % \ i \%
um;
H
S \G
B.
I
V
Figure 411
ure 4G.
The p a t t e r n is c u t into 3 pieces on lines G and H. A n e w guide l i n e is drawn on a fresh sheet of paper."
The pieces of the pattern are placed on the paper so that the guide l i n e of each piece f a l l s on the guide l i n e drawn on the
with the tting of the pattern in Figure 4G. In 4G, the gathers at the neckline f a l l only to the bust. The rest of the tting has no surplus fullness.
paper.
In 41, the gathers at the neckl i n e and waistline produce excess fullness a l l through the
tting.
The p a t t e r n pieces of Figure 4H can be spread so that m o r e fullness is added only to the waistline.
FIGURE 4K.
Figure 4.1
Figure 4K
U s i n g T h e Bust Dart As
Pleats Or
Tucks.
Figure 5A
Figure SC
FIGURE 5A. Figure 5A is the same as Figure 4E. The dart fullness is used to make aninv e r t e d pleat.
W I Q Q
Figure 5B
FIGURE 5B. Line D-F is folded over to the center l i n e B-A. Line E-G is folded over to the center l i n e B-A.
A tracing wheel should be rolled through the neckline over the folded darts, or the neckline can be cut out with the dart folded.
FIGURE 5C. This is the shape of the folded neckline when it is opened.
The shaded area shows the depth of the pleat. The waist dart can be shortened if desired.
Figure 5CC
11
If the dart is to be divided into many small pleats or tucks, it is easier to draw r s t the exact position of the tucks and then shift the d a r t i n t o them.
Figure 6C
The correct shape of the tucks at the shoulder line can be obtained by folding the tucks in the paper p a t t e r n the way they are folded in cloth.
Figure 6B
The pattern in Figure 6A is c u t on lines B to A, C to A, and D to A. The B u s t Dart
Lines B, C, and D show the posit i o n desired f o r three shoulder tucks. Each tuck. is drawn the length desired and then connected to point A, the center of the bust area.
E-A-F is
c u t out.
A tracing wheel is r o l l e d through the shoulder, over the folded tucks, or the shoulder l i n e can be c u t out with the tucks folded.
IT IS IMPORTANT THAT EVERY T U C K OR PLEAT MADE FROM THE BUST DART FALLS WITHIN THE BUST AREA. (See Figure 1B.)
The dotted lines continuing from B, C, and D show where the tucks would f a l l if they were continued to the bust area.
Tuck D is as f a r out as it can be f o r satisfactory results.
The folded tucks in Figure 6C are opened. The arrows at the bottom of each tuck show the direction the tuck is to be folded when stitched in cloth. The d a r t fullness remaining at the waistline is to be gathered between points G and H.
FIGURE 6D.
GATHERS
Figure 6D
Figure 6DD
FIGURES 6E and 6F show how it is possible to introduce more fullness into the pattern than the bust d a r t allows.
(See Figures 4H, 41, 4J, 4K where the s a m e procedure is used
for gathers.)
I III I I I I I
'
I I
| I
I
I I I
I I I
|
I
I I
I I I
I I
I I I
I
I
Figure 6F
Figure 6E
Lines are drawn from each tuck or pleat in the same direction it f a l l s , to some outside edge of the pattern. (Here it is the waistline.)
Each tuck is made wider by spreading the p a t t e r n pieces from the waistline, which changes i t s shape but remains the same size. Each tuck w i l l have to be folded again as in Figure 6C to get the n a l shape
of the shoulder line.
Figure 6G
It is possible to spread the p a t t e r n pieces of Figure 6E at the waistline only so that the tucks B, C, and D remain the same size at the shoulder line, while the waistline increases in size.
13
Figure 7A
In t h i s gure the tucks are drawn at the neckl i n e . Checking the tucks position in r e l a t i o n to the bust area shows that tuck E falls far outside.
Figure 7 B
Figure 7C
Only tucks B, C, D can be opened by closing dart F-A-G. TUCK E HAS TO BE CUT ON ITS OWN LINE THROUGH TO AN OUTSIDE
E D G E OF THE PATTERN.
The tucks should be folded in the paper as they will be in cloth, and the neckline shape corrected.
A tracing wheel can be run through the folded tucks at the neckline or the neckline can be cut out with the tucks folded.
DART.
THE FULLNESS F R O M TUCKS B, C, D WILL DISAPPEAR AT THE BUST. THE FULLNESS F R O M T U C K E GOES THROUGH THE ENTIRE PATTERN MAKING THE PATTERN W_IDER ACROSS THE BUST.
Dart F-A-G can be shortened f o r
a s o f t e r effect.
44:
\\
Figure 7D
the corrected shape of the neckline.
Figure 7DD
This is the cloth tting of Figure 7D.
14
V}/ \/
Figure 8A
Figure 8B
Figure 8C
Figure 8D
Figure 8 D D
FIGURES 8A, 8B, 8C, 8D and 8DD. These gures show the bust dart E-A-F shifted to three tucks
drawn from the center f r o n t at the bustline.
A c l o t h t t i n g (Figure 8DD) is important to check the curve of the n e w center f r o n t line.
15
V V 1 I i . :v '; I
FIGURES 9A and 9B show the bust dart C-AB shifted into six tucks or pleats drawn from the shoulder and waistlines.
F
A foundation pattern with the bust dart at the side s e a m is used because it does not i n t e r f e r e with the placement of the s ty le tucks. ( S E E method f o r Shifting The Bust Dart, Figures 2A-2C.)
The tucks should be folded in place as explained in Figure 6C to get the correct shape f o r the shoulder and waistlines.
Figure 9A
FIGURES 9C and 9D show how the tucks can be made l a r g e r by cutting and spreading the p a t t e r n . Figures 6E, 6F and 6G show the same process with only shoulder tucks.
Cutting and spreading the p a t t e r n to add more fullness than the bust dart allows increases the width of the pattern across the bust.
Figure 9C
Figure 9D
FIGURE 9CC shows the cloth tting of Figure 9C. The soft folds f a l l from the end of the stitched tuck to the bust. THE FITTING IS SMOOTH
Figure 9 C C
FIGURE 9DD shows the cloth t ting of Figure 9D. The extra width placed in the tucks increased the fullness through the bustline. The soft folds continue from the shoul der to the waistline over the bust.
16
Figure
9131)
FIGURES IOA, 10B, 10C, 10D show the bust dart shifted from the side s e a m to make two other darts, retaining some d a r t at the side seam.
Figure 10A
Figure 10B
Figure 10C
Dart 2 is almost too f a r off the bust area to be a bust d a r t . It has been made smaller than d a r t 1 deliberately to offset its forced position. The extreme s l a n t of the l i n e which joins the d a r t to point A indicates i t s limitations. A cloth tting may show it to be
impractical.
The darts have been drawn in their new positions. They should be folded in position as shown in Figure 10-D to get the correct shape f o r the The side seam waistline. dart should be folded, too.
Figure 10D
Figure 10CC
A cloth t t i n g should be made of the p a t t e r n in Figure 10C to check on the lengths of the darts and their positions.
Figure IOCC
17
U s i n g T h e Bust D a r t In
A Style L i n e .
When a style line goes d i r e c t l y over the bust, the dart fullness can be moved d i r e c t l y into the style line, seeming to disappear.
c
'
a
Figure l1BB
Figure 11A
the style l i n e directly through the center of the Bust A.
Figure llB
D-A-C is
going
The pattern is c u t i n t o two pieces, cutting away the bust dart B-A-C.
A c l o t h tting should be made to check the shape of the l i n e D-AB at Both p a r t s of point A. the patterns should be c u t in muslin or other tting cloth with seams allowed. Line D-A-B is stitched to l i n e D-A-C. Both l i n e s are the same length.
In t h i s gure the style line is not drawn d i r e c t l y through the center of the bust A. It is so close, however, t h a t point A can be moved to the style line and a n e w dart l i n e AA-B drawn.
The n e w dart B-AA-C should be the same s i z e as the o r i g i n a l dart B-A-C. The pattern pieces are separated as shown in Figure 11B.
Figure 11C
13
Figure 11D
The pattern is cut into two pieces on l i n e s B-AA-D, and C-AA-D.
Line D-AA-C is longer than l i n e D-AA-B. The extra length should
,
Figure l1DD
A c l o t h tting should be made to check the shape of l i n e D-AA-B. The tting will also show t h a t the extra length in l i n e D-AA-C f a l l s easily within the bust area and is unnoticeable .
or
Figure 11F
Figure 1113
Figure l1FF
A cloth tting of the pattern in Figure 11F shows no visible evidence of the bust dart in the s t y l e l i n e D EF-G.
In this gure the style l i n e D - A - G is drawn d i r e c t l y through t h e center of the bust A, but is not part of the waist dart.
E and F are two notches located to aid in sewing.
The pattern is cut i n t o two pieces on the s ty le l i n e D-AG. The bust dart B-A-C is cut out and closed by bringI
The shape of line D-AG in the lower section changes when the bust dart is closed, b u t remains the same length. The corner at point A can be rounded
off.
19
The style l i n e D-EF-G is drawn outside the bust area. It becomes a yoke l i n e . (See Section on Yokes.) The bust dart BA-C can be shifted i n t o the yoke l i n e but some evidence of the dart must be seen, as gathers or pleats or
tucks or darts.
In this gure, the bust d a r t is shifted as gathers i n t o the yoke l i n e between the points E and F, covering the bust area.
The dotted lines 1, Z, 3 from A to the yoke l i n e help spread the d a r t fullness smoothly. The pattern is cut in two pieces on l i n e D-EF-G. The dart BA-C is c u t out. Lines 1, Z, 3 are c u t ALMOST to point A.
Figure 12A
Figure 12B
Figure 12C
A new, curved l i n e must be drawn between E and F.
Figure 12D
This shows the nished pattern of Figure 12C.
Figure IZDD
This shows the muslin tting of the pattern.
Figure 12E
In this gure, s o m e of the bust dart has been l e f t at
the waistline.
Figure 12F
The dart at the waistline m a y be shortened below
point A.
Figure
IZFF
21
Figures 12G and 12H show how more fullness can be added both to the yoke line and the waistline by cutting and spreading the pattern. (See Figures 4H, 4I, 4.}, 4K.)
D E
#7
LINE
E\F
1.
E
GUIDE
-E
:
LINE
Figure IZG
Figure 12H
Figures 121, IZJ and 12.1.1 show a yoke style line made across an open dart. No shifting of the dart is necessary.
Figure l2I
The yoke line A-B-C-D is drawn as desired across the dart G-I-I-I.
Lines G-B and I - C must be the same length. (It helps to fold the d a r t closed when drawing the yoke line.)
Points E and F are notches between which the gathers w i l l be conned.
Figure I Z J
The yoke pieces are c u t away from the rest of the pattern. Sections 1 and Z are traced together as one piece. The center f r o n t l i n e can be a f o l d l i n e .
Q
,
Figure 12;
The dart space remaining (B-H-C) can be used for gathers, pleats, tucks, darts, e t c .
Figure lZJ
Figure I Z J J shows the finished appearance of the p a t t e r n with the dart fullness used as gathers.
Figure I Z J J
22
FIGURES 13A, 13B, 13C, and 13D i l l u s t r a t e the bust dart shifted to a yoke l i n e as pleats or tucks.
01
_ . _ _ _
Figure 13A
Figure 1313
The pattern temporarily is cut in two from D to l i n e 3, down to A and B.
Lines 1,2, 3 are cut ALMOST to A.
Figure 13D
The tuck spaces 1,2,3 should be made even. The tucks should be folded in place either in the paper p a t t e r n or in the c l o t h tting so that a straight line can be drawn across the folded tucks from D to E. (Figure 13D.) The dotted line across the tucks shows the corrected line D-E.
The waist dart m a y be l e f t as a dart, or gathered.
Figure 13CC
Figure 13CC shows the cloth tting of the pattern in Figure 13C.
Figure 13C
Figures 14A, 14B, 14C illustrate how fullness can be added to a waist front without using the bust dart to make the f u l l n e s s . (Here the bust dart remains at the waistline as gathers. )
Although t h i s does not add to the information on bust darts, it does show that
T H E PATTERN MUST ALWAYS BE CUT AND SPREAD IN THE S A M E DIRECTHION TI-IE FULLNESS IS TO FALL.
Figure 1413
Figure 14C
Figure 14CC
Style Line
. . . . . . . . . . . . . . . pages 27-28
Page 27
Page 28
Page 28
Page 29
25
26
U s i n g T h e B a c k D a r t s In
A Style L i n e .
The back waist pattern in the following figures is the basic back waist pattern from Book I (Foundation Patterns).
Figure 1A
The shoulder and waist d a r t s can be moved i n t o any style line drawn in the same area as the d a r t s .
Line A-B is a style l i n e drawn any shape. A-C is the length of the shoulder d a r t . B-D is the length of the waist d a r t .
Figure 1B
Figure 1C
The pattern is cut into two pieces, eliminating the dart spaces. The darts are invisible, but present, when the two parts of the pattern are sewed together.
Figure ICC Figure ICC shows the c l o t h tting of the pattern pieces in Figure 1C.
27
Figure
2A
Figure 2B
The pattern is cut into two pieces on the style line D-B-E. The d a r t space A-B-C is cut out. Lines A-B and C-B are placed together, elimi n a t i n g the dart space, and the new p a t tern piece is drawn.
Figure ZBB Figure ZBB shows the muslin tting of the pattern.
The style line (D-E) in this figure goes only through the area of the waist dart (A-BC).
G a t h e r i n g T h e B a c k W a i s t Dart To
A Yoke.
A C
as-g1>\
T
Figure 4BB Figure 4 B B shows the c l o t h t t i n g of the p a t t e r n in Figure 4B.
'
'.-
FAAH
Figure 4A
In this figure a neck yoke line (D-E) and a waist yoke line ( I - J ) have been drawn.
The neck dart will be l e f t as a dart beneath the yoke. (It can be gathered or f o l d ed as a small pleat.) The waist dart will be gathered between points K and L.
FIGURE 4B. 'The neck yoke is cut away from the rest of the pattern. The d a r t space from A to C is cut out, leaving the neck yoke in two Figure 4B pieces. The pieces are placed toa gether at the dart lines and a n e w one-piece yoke is drawn without dart. The dart is hidden in the n e w shape of the neck yoke.
The s a m e procedure is followed f o r the waist yoke.
The dart space l e f t in the body of the pattern is gathered between points K and L to match points K and L of the waist yoke. 28
FIGURE 5A. The back waist has been joined to the back skirt to permit a yoke (IE-H-L) to be drawn across t h e waistline. (See Book I, Foundation Patterns.)
A shoulder yoke (M-N) is also shown.
FIGURE 5B. The pattern is c u t i n t o three sections on the yoke lines M - N , E-H and I- L.
The shoulder yoke section shows the one dart made into two, as a s t y l e p o s s i b i l i t y. The center section can be c u t and spread to allow for gathers between points M - O and 15-13, as shown in Figure 5C.
6 IDE
FI
J
o
_, LINE
_ . _ . _ <
In the waist yoke section the dart space is cut out and points F and G and J and K are brought together, leaving a small dart (J-A-F-C-K). In certain materials this small dart can be eliminated by removing s o m e of it from t h e center back s e a m and s o m e from the side s e a m as shown by t h e dotted lines. This can be tried in the c l o t h tting. (See Figure SCC.)
m "
'1
= : : '; '
Figure 5B
ON
\\\\\\\\
\\\\\\
\\\\\\\
LINE
\\\\
\\\
.\\\
3IIt:2.t
to t h e
bottom.
t h e center section is gathered fzt M - O of the shoulder yoke sec'm:m..m:. in Figure 5B.
in
M-O of
Figure 5 C C
Figure 5 C C
fJF".g-re 5B.
Figure SCC shows two cloth ttings. In one, the waist darts have been kept in the waist yoke. In t h e other, the dart has been eliminated by removing it frorn t h e center back and side seams.
29
INDEX
_
TO
SKIRTS
~~..'-
Page 35
Page 36
Page 37
\LLL
Page 38
Page 38
Circle Skirts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . pages 43-46 Whole Circle Skirts . . . . . . . . . . . . . . . . . . . . . . page 43 Half Circle Skirts . . . . . . . . . . . . . . . . . . . . . . . page 45 Quarter Circle Skirts . . . . . . . . . . . . . . . . . . . . . page 46
Page 39
Page 40
Page 41
SeamF1ares...................
.pages47-50
Page 47
Hi
n..-
II
Page 49
Seam Pleats.................................page 51
inn-
nu
LI)
llll
s
:'l"|"
.Hu-.U
Page 51
Page 51
Godets.......................
pages 52-53
I\
Page 52
Page 52
Page 53
Page 53
The following pages illustrate basic skirt style variations such as yokes, pleats, gathers, flares, e t c . A l l of the styles are drawn on the skirt foundations patterns from Book I on Foundation Patterns.
A yoke line, or any style line drawn in the area of the skirt darts is handled in way as in a l l other dart areas. (See the sections on Bust Darts and Back Waist Darts.)
B a c k Skirt H i p Y o k e
aAcK
Figure 1B
The d a r t A-B-C is c u t out and closed by bringing lines A-B and C-B together.
Figure 1A
The pattern is then drawn as a one-piece hip yoke with no d a r t . The d a r t is hidden in the curve of line D-B-E. The center back line is placed on a fold.
Figure IBB
Figure 2A
When the back yoke line is drawn lower than the hip dart, a l i n e must be drawn from the bottom of the dart to the yoke l i n e (B-F). The yoke l i n e should not be drawn lower than the hip section in any case, if t h e yoke l i n e is to remain a t ted line.
33
at point F.
FIGURE 2B. The yoke is cut away from the skirt pattern. The dart A-B-C is cut out. Line F-B is cut, ALMOST to point B. The d a r t A-B-C is closed, opening a small space
The extra space in line D-E can be gathered and shrunk out so t h a t it is i n v i s i b l e , if not more than about 1/2", depending on the fabric used.
Figure 2B
T h e Front Y o k e .
Figure 3A
A front yoke l i n e E-D has been drawn slightly below t h e dart A-B-C. A l i n e must be drawn from the end of the dart to the s t y l e line (BF).
Points G and H help in sewing the yoke line to the s k i r t .
Figure 3B
The yoke is cut away from the rest of the pattern, and the same procedure followed as in Figures 2A and 2B f o r the back.
FIGURE 3 B B shows
of the yoke pattern.
Figure 3 B B
34
Front Y o k e A n d Center P a n e l
FT
LNE
GIFLIDE
*1
-
3
LINE
2 u_
I In Z In 0
I
I
'
' -
__ __ _
T L
_ _ __
t
:_
- 2 -
F
Figure 4A
F
Figure 4B
___
Figure 4c
__
FIGURE 4A. The yoke and panel lines (D-E and EF) are drawn as desired.
A panel line is m o r e pleasing to the eye when it is drawn so that the panel is Wider at the bottom than the top, by about one inch. (See Figure 14A.)
FIGURE 4B. The yoke and panel are cut away from
invisible.
The dart space is cut o u t and the dart lines brought together, making the dart
the rest of t h e p a t t e r n .
The side section of the pattern can be cut into as many sections as desired f o r creating additional fullness either by m e a n s of gathers or flares, or even loose pleats. (See Figure 4D.)
A guide line has been drawn to help spread the sections in a straight line.
FIGURE 4C. Here the side sections have been spread for gathers, or pleats, under the yoke.
loose
Figure 4 C C
The curve of the side seam no longer necessary, a straight l i n e can be drawn from the waist to the h e m as shown by the dotted line D-G.
c l o t h tting of the pattern with the side sections of the skirt gathered to match the yoke lines. 35
F R O N T
C E N T E R
an
"
if
_____
F
F
Figure 4B
A flare can be added to the center panel l i n e from E to the hemline, matching the flare from point E of the side section.
- % . _ _ : : "
Figure 4D
In this gure, the side sections are spread in a circular fashion for circular flares. See Figure 9B also.
The sections are kept together at line DE, while t h e width of the hemline is increased.
the cloth
t t i n g of the pattern.
Figure 4 DD
36
Front Y o k e A n d L o o s e Pleats
41 '5
Figure4F
Figure 4G
The yoke is cut away from the rest of the pattern. dart space A-"B-C is cut out and the dart closed.
The
The rest of the skirt is cut i n t o sections 1,2, 3,4 and The sections spread as desired for the loose pleats. can be spread wider at t h e bottom as shown so that the pleats will have m o r e depth at the hemline.
It is important that the sections remain level with each other no matter how far apart they are spread.
\ ~ _
The p l e a t s should be folded in paper the way they will be laid in c l o t h and a tracing wheel rolled through l i n e DE to get the correct yoke line in the p l e a t spaces. The dotted lines from 1 to 2 to 3 to 4 show the shape the l i n e takes to make the curve of line D-E.
rL
Figure 4GCv
37
P L E A T S A N D GATHERS
When the skirt is gathered or pleated throughout the entire waistline, no basic skirt pattern is needed. The final pattern can be drawn immediately by Calcul a t i n g the amount needed to make the gathers or pleats desired.
Groups of narrow, pressed pleats are best l e f t to the professional pleater who has the proper machines.
Other types of pleats and gathers are made by cutting and spreading the s k i r t patterns. Some types have been illustrated in Figures 4C and 4G.
GATHERS
E; l.|.l
(D
3 E
K Ill
Figure 5B
*5
(D
'2 3
Figure 5A
FIGURE 5A. This pattern represents one-half a back or a front skirt to be gathered at the waist.
For gathers, a width two to three times the finished waist measurement is usually allowed.
Figure 5C
This diagram shows the pleats folded in place. Only the oneinch p l e a t spaces show on the surface. The two-inch p l e a t inlay folds in half t o r n a k e a p l e a t one inch deep.
essary for the pleat inlays must be gured and each p l e a t space (or face of the pleat)marked.
This figure shows only a section of the entire pattern which has been marked o ff in pleat spaces. There are 28 oneinch pleats (A) making a 28'' waistline. The p l e a t inlays (B) or the amount the pleat f o l d s i n , are two inches, making a p l e a t 1" deep.
FIGURE 5B. For all-over loose or pressed pleats, the amount nec-
The skirt will have 28 pleats, 1" apart and 1" deep.
FIGURE SBB
pleated skirt.
shows an all-over
m i x
Figure 5 A A
38
Figure 5BB
A L i m i t e d N u m b e r of
Loose Pleats.
The pattern must be cut and spread where each pleat is to f a l l . The procedure is the s a m e one described in Figure 4G.
A back s k i r t is handled in the same way.
MEN
H 3 . L N 3 0
H 3 J . N 3 3
. L N O U J
. L N O H : |
F R O N T
C E N T E R
-1'-
I
Figure 6A
2
___._.__...._
-* ------J
Figure 6B
The pattern is cut on line 1-1 and spread any depth desired for the p l e a t .
The center p l e a t depth is allowed directly to the center f r o n t , making a n e w center f r o n t l i n e which can be placed on a fold.
The arrows point to the directions in which the pleats are to The pleats should be folded in the paper and a tracing wheel rolled through the waistline to get the correct shape of the waistline in the p l e a t depths.
be folded.
Pleat 1 can be folded over a l i t t l e deeper to point A to take 0 in_ the space of the d a r t .
the pattern. The two side pleats facing each othe r at the center front make an i n verted pleat.
39
CIRCULAR FLARES
A flare is additional width or fullness added to a skirt causing it to spread o u t . Circular flares are so named because the skirt is spread in a circular fashion to obtain the additional width.
F l a r e s F r o m T h e Skirt Darts
In both the front and back skirt patterns the waist d a r t s can be used to open a r e s in the skirt. This keeps the flare below the level of the dart. Thus, a four piece flared s k i r t can be made in which the hip area is smoothly t t e d because the flares fall from the hipline.
O
Z
l"'|
TH 3
U!
-4
P
O X
___...___._.
Figure 7A
Figure 7B
FIGURE 7A. A line (F-H) is drawn from the base of the dart to the h e m in the direction the p l e a t is to f a l l . FIGURE 7B. The dart space EF-G is cut o u t . The pattern is cut on l i n e H-F A L M O S T to point F. The d a r t E-F-G is closed, open~ i n g space H-FH. This flare f a l l s only from point F.
Additional flare can be added to the center back seam from the hipl i n e as shown by the dotted line I- J.
Additional flare can be added to the side seam as shown by the dotted line K-L. (See Figures 9A and 9B as well.)
Figure 8A
Figure 8B
The waist dart A-BC is closed as described in Figure 7B. The pattern is cut on the a r e lines from the h e m A L M O S T to the waistline. The sections are spread to give as m u c h width at the h e m l i n e as desired. The pieces of the pattern must l i e absolutely at.
Additional a r e s can be added to the center front and side s e a m s if desired as shown by the dotted lines.
41
I I
Figure 9A
I I
I I
I I
F R O N T
C E N T E R
Figure 9B
FIGURES 9A and 9B. These gures show the same procedure f o r the front skirt pattern.
the s a m e depth as in the back.
Figure 9BB
42
CIRCLE SKIRTS
A circular skirt can be cut on the basis of a circle without using a basic skirt, pattern. The amount and position of the flares cannot be controlled in t h e s a m e way they are when the skirt pattern is cut and spread. Skirts can be cut as a WHOLE CIRCLE, a H A L F CIRCLE, and a Q U A R T E R CIRCLE with comparative differences in the sweep of the hem.
T h e W h o l e Circle Skirt.
""T:.e edges of the paper can be used as guides.) The corner is markti C f o r identification. This represents O N E - Q U A R T E R OF T H E _,I3rI1RE SKIRT.
sum: SEAM
/7?
"Um draw t h e part of the circle which K gured (the radius of the circle).
the waistline, l i n e C-D must CD is one-sixth the measureillmuent of the entire waistline. If t h e waist measurement is 24", line ID-D is 4". CD is measured off as many times as necessary from NJ I C to draw the waistline curve DDD~DD. If the waistline is to yk 24', the curve DDD-D-D, which is ~ -quarter of the entire waistline, Aw measure 6". It m a y be 1/4" so too large, in which case e CD is shortened a bit a n e w curve drawn m the waistline.
is
of the skirt
measured off
am the waistcircle and '''iilel to i t .
Figure l0A
/XDA
FIGURE 10B. This g ure shows how four of these sections are necessary to make an entire skirt. The sections
can be cut together m a k i n g a skirt with no s e a m , or with only two seams,
if desired.
Figure IOB
FIGURE IOBB.
seen.
the c l o t h tting of the finished skirt, spread so t h a t half its width can be
Figure 1GBB
43
A SKIRT CAN BE CUT AS T W O W H O L E CIRCLES IF AN E X T R E M E L Y F U L L SKIRT IS DESIRED. T H E WAIST MEASUREMENT IS DIVIDED IN H A L F A N D E A C H H A L F MADE INTO A W H O L E CIRCLE SKIRT. For a 24-inch waist
measurement, there would be two whole circle skirts, each measuring 12" at the waistline.
Figure 11A shows the construction of such a skirt with two pleats in each quarter skirt. Figure IIAA shows t h e cloth tting of the finished skirt.
The skirt resembles t h a t in Figure 6BB but has a f u l l circle
sweep at
the hem.
CENTER FRONT
S E A M
SUE
Figure 11A
Figure l1AA
44
T h e H a l f Circle Skirt.
A
SIDE SEAM
OR
CENTER BACK
FIGURE 12A. The procedure is the same as described for Figure 10A E X C E P T T H A T LINE
The waist curve DD-DDD should measure one-half the e n t i r e waistline or be adjusted to \ by shortening or lengthening l i n e C-D.
lithe waistline is 24", l i n e cD is about 8" and the waist curve D should measure 12".
$1: 1: B
<
E O
E
m #1 2
Q
Figure 12A
This gure shows the two sections nec~ essary to make the e n t i r e
skirt.
FIGURE 1213.
Figure IZB
This gure shows the c l o t h tting of the nished skirt spread so t h a t h a l f i t s width can be seen.
FIGURE IZBB.
Figure IZBB
45
T h e Q u a r t e r Circle Skirt.
A
SIDE SEAM
FIGURE 13A. The procedure is the s a m e as described for Figures 10A and 12A, EXCEPT TI-{AT LINE CD IS APPROXIMATELY T W O THIRDS T H E WAIST M E A S U R E M E N T .
The
waist curve, D-DD-DD, should be the entire waist measurement, or adjusted to t by lengthening or shortening line CD.
If the waistline is 24", line CD is about 16", and the waist curve D should measure 24''.
S E A M
S I D E
Figure 13A
FIGURE 13B. This figure shows t h e one section necessary to m a k e t h e entire skirt.
Figure 13B
FIGURE 13BB. This figure shows the c l o t h t t i n g of the nished skirt spread so that h a l f its width can be seen.
Figure 13BB
46
S E A M F LARES
A seam flare is additional width or f u l l n e s s added to the lengthwise seams of the skirt. Skirts can have any number of lengthwise seams, dividing the skirt i n t o panels or gores. Figures 14BB and l5BB show a 6-gored skirt and an 8-gored skirt with s e a m a r e s . Figure l6CC shows a 16-gored skirt with seam flares.
EH
A
1
I
..J
_J
,4
LL
IL
I-Z
ta: .n: II
3 L
1::
|-
u.|
IZ
LL]
|.|.l
Z_
Lu O
1
Figure 14A
o
Figure 14B
A panel l i n e or gore line H-1 has been drawn on the basic front skirt pattern. The panel will have a better shape if the bottom width (I- B) is made about one inch m o r e than the top (HA).
The skirt is cut i n t o two sections on the panel line H- J'I. Any amount of are (I-K) can be added to the hemline from the points I. The n e w s e a m are l i n e is drawn from K to J. J-K must be m a d e the same length as l i n e J - I .
Point J is the level from which the are will f a l l , and can be any place
C.
Equal halves of the waist dart can be removed from each section of the pattern. The seam line n o w runs G-F- J-K or E-F-J-K.
the l i n e .
FIGURE 14BB. This figure shows the cloth tting of the pattern.
47
Figure l4BB
Figures 15A and 15B follow the s a m e procedure described in Figures 14A and 14B, except t h a t the center f r o n t or back is kept a seam l i n e instead of a f o l d line.
A a r e can be added to the center back and front seam lines, and the entire skirt c u t as eight pieces.
S E A M
B A C K
C E N T E R
Figure 15A
Figure 15B
The waist dart E-FG can be divided equally into three parts, each part removed from a seam line as shown by the dotted lines 1, 2, 3. The center back s e a m is n o w lF J-K. The panel seam lines are Z-FJK and 3-F-J-K. The side seam l i n e is
CJ-K.
Figures 16A-16C show the procedure for making a sixteen-gored skirt with gores
of equal size.
4 _ _ _ . _ _ _ _
F R O N T
C E N T E R
Figure 16A
The f r o n t and back skirt patterns are traced together at the side seams. The entire skirt area is divided equally i n t o the number of gores desired.
49
P
3:
Z O
0:
3 "J
l 2 Lu 0
LIJ
U-
Lu
IZ DJ 0
3 0:
|_
,_
LL
m
Lu
Figure 16B
Figure 16C
Each gore or panel is traced through separately on to another sheet of paper (without the shaded d a r t areas) so that flares can be added, or pleats, if desired. (See Figure 17A for the addition of pleats.)
The t o t a l amount of dart space, (the front, side seam and back waist darts) is divided equally among the gores, as shown by the shaded areas.
E-
FIGURE l6CC. This gure shows the finished appearance of a flared 16-gored skirt.
L
Figure 16CC
50
r 5 1 1 5
S E A M PLEATS
Just as a a r e can be added to the lengthwise seams of the skirt, so can additional width for pleats be allowed.
\I
A
of a r e s . The p l e a t allowance has width at the top, different from the flare.
V
-F
FIGURE 17A. The same skirt sections of Figure 14B are shown here with pleat allowances instead
-F
The p l e a t allowance m a y be the same width top and bottom, or the top can be made narrower as shown by the dotted lines. The p l e a t allowances are usually h e l d in place by top stitching along the seam lines.
See Figure 6B for pleats running the f u l l length of the s k i r t .
J
O
_I
ll...
FZ
o I
iZ
IL
ILI
ll]
:iZZi:_:::j
ance of the pattern. These are two side pleats, facing in opposite directions.
'3
tl
! I
>
o_
L_:J
Figure 17A
I2
,
3
3
L 1
\ \
L
verted p l e a t can be made from the side pleat, allowances in Figure 17A by adding a p l e a t i n l a y section to the pleat allowances.
-_
a
Figure l7AA
_ _ . '2
, _ . -
~.-
I \ , _ .
, . _ _ _ _ . _ -
The p l e a t inlay secis the size of both side p l e a t s . KL is stitched to K-L of the s k i r t .
tion
Figure 17C
Figure 17D
Lines 51-1 of the skirt sections are creased and folded over to meet on line J-L of the inlay section.
Two side pleats facing each other make an inverted pleat. Two side pleats fairly close together, facing in opposite directions, m a k e a b_ pleat.
A series of inverted pleats as in Figure l7D are also a series of box pleats.
Figure 17B
verted pleats. 51
GODET S
A godet is a separate piece inserted into a part of a garment to give a difference of width at a particular place.
Two basic types of godets are illustrated here as skirt godets. can be used in the same way in any part of the garment.
a flare.
They
-- B
Figure 18B
The triangle f o r the godet is drawn as large as desired. A l l the length l i n e s of the godet (A-B) must be the same length as the slash l i n e A-B of the s k i r t .
3
Figure 18A
The slash line A-B is drawn any place on the skirt.
FIGURE 18BB. This gure shows two_ ways this godet can appear in the finished skirt-as a flare tucked away inside the slash, almost like a pleat, and as a flare which "pops" out of the skirt.
Figure ISBB
52
54
. . . . . . . . . . . . . . . . . . . . pages
69-75
Page 74
Page 75
.56
Page 75
HEIGHT
/
CAP
or
O> X
X O D W
< - - --
Figure 1D
Figure IE
Figure 1F
a c l o t h t t i n g of the onethe a r m is lowered. when best t s sleeve The piece t t e d sleeve. There is no excess fullness under the a r m or in the width of the sleeve. The wrist is tight. The sleeve cap has the m i n i m u m full ness necessary to t smoothly over the curves of the shoulder and t h e top of the a r m . The amount of extra fullness in the sleeve cap about one inch (from A to B to C in Figure 1C) usually averages used. the fabric on m o r e than the armhole, depending
The a r m can be raised no m o r e than about h a l f way between the shoulder and waistline without pulling up the rest of the garmerit. (As soon as the a r m is raised, diagonal wrinkles form from the top of the a r m to t h e underarm. )
V a r i a t i o n s In
T h e H e i g h t Of
T h e Sleeve Cap.
Figure 2B Figure 2A FIGURES 2A, 2B, and 2C. These figures show what happens to the t of the sleeve when the underarm is lengthened and the sleeve cap made shallower. The sleeve has to become wider and so l i t t l e or no extra f u l l n e s s is needed in the cap to t over the top of t h e a r m . The a r m can be raised almost shoulder height without pulling up But there is excess t h e rest of the garment. fullness in the underarm when the a r m is lowerThe sleeve shows diagonal wrinkles from ed. the top of the cap to the underarm. This type of sleeve, found in sport shirts, is best used when freedom of a r m movement is m o r e important than a smoothly t t e d cap.
More details on t h e construction of such a sleeve cap can be found in Book I. The sleeve cap line can be made as shallow as desired, even approaching a
straight line.
58
Figure 2C
V a r i a t i o n s In
T h e B o d y Of
T h e Sleeve.
Those style variations which a f f e c t only the f r o n t or back of the sleeve, or both, are m o s t easily made when the sleeve is folded like an a r m . The design can be drawn exactly as it is to appear finished, and then the sleeve opened.
Folding The Sleeve.
F R O N T
Figure 4A
The back underarm line DE-H is folded over to the overarm or center line of the sleeve.
First the upper half D-E is folded over, thenythe bottom half E-H.
Figure 4B
Line D - F of the front underarm line is folded over to meet l i n e D-E of the back.
The elbow line must be cut from F to the f o l d before the bottom h a l f FJ can be folded over.
60
I I I
I I
Figure 5D
The bottom width of the sleeve can be gathered to a band cuff. The c u f f usually is cut twice the nished width, plus whatever underlay is necessary for buttons or snaps or any other fastening (the shaded section).
I I
I I
I
I I
I
FIGURE 513.
Extra length can be
I I
added to the sleeve if m o r e of a puffed effect is wanted when the sleeve is gathered. (The straight grain l i n e is usually shifted to the center of the sleeve.)
I I
L.
I I
Figure SEE
This gure shows the nished appearance of the gathered or "Bishop" sleeve in Figure 5E.
'~___
: _ . . .
_ j
,1 I
1..._
Figure SE
_
_
_I
T
Figure 5F
Figure G
.1
FIGURES 5F and 5G. More width can be added to the body of the sleeve as well as the bottom by cutting and spreading the sleeve pattern of either Figure 5C or SE, from the bottom almost to the cap line. The pieces must l i e a t when spread, b u t they can be spread any amount. 62
WW
IIHH
T>
\
|\
HHHIIH
ill
Figure SI-I
More width can be added to the cap Line of the sleeve as well as the bottom, if desired, by spreading the pieces along a straight line. The pieces can also be spread so t h a t m o r e fullness is added to the bottom than the cap. (See Figure 11B.)
The n e w cap line can be drawn as dotted lines.
indicated by the
FIGURE SH.
The sleeve does not have to be made f u l l length. Wherever it is, the n e w bottom line should be drawn perpendicular to the center l i n e of the sleeve. (See the lantern sleeve, Figure 8A, and also following Figures 6A-6BB.)
FIGURE 5HH. This gure shows the finished appearance of the sleeve in Figure 5H, gathered to a band cuff, or l e f t loose at the bottom, gathered only
31 the cap.
/
Figure 5 H H
63
Figure 6A
Figure 6B
Figure 6BB
FIGURES 6A, 6B and 6BB. These figures show how width is added to the f r o n t and back of a short sleeve. The procedure is similar to t h a t described for Figure 5A. The sleeve in Figure 6B can be cut and spread as m u c h m o r e as desired as described in Figures 5G and 5H.
(Figures 11A and 11B show other ways in which the short sleeve can be c u t and spread without first folding the sleeve.)
u r . : .
A d d i n g To
T h e B a c k Of
T h e Sleeve Only.
l | I
FIGURE 7B.
is
as
5A-C.
~ ~ .
s . , . '
V.
Lf, Figure 7A
iL
Z \ / F
_
Figure 7 B B
This gure shows the finished appear3-RC6 Of the Sleeve-
A straight line drawn from L Figure 7B through K can be extended as m u c h as desired to point M. Point M is connected to the cap line. Point L can a l s o be connected to the cap line by a straight line. The curve of the elbow is no longer necessary since there will be no elbow dart in this wider sleeve.
A n e w underarm line can be drawn from D through the center of t h e n e w bottom l i n e M--L. In t h i s sleeve it coincides with the grain line, b u t it m a y not always. The straight grain line can always be made the center of the sleeve. 64
folded sleeve.
Figures 9A, 9B, and 9BB show another s ty le variation t h a t can be made on a The sleeve flares out in a point at the back over a t t e d cuff.
K
Figure 9A
The t t e d cuff O-N-M-L-I-K-O can be drawn as desired. The rest of the style line OP is drawn as desired and joined to the cap line.
A straight underarm seam l i n e can be drawn from D to N. The undera r m seam line of the c u f f is N - I . A straight f r o n t line can be drawn from M to the cap line.
Figure 9B
FIGURE 9BB. This gure shows the finished appearance of the sleeve.
Figure 9 B B
66
Figures 10A, 10B and IOBB show another s ty le variation which can be m a d e on a f o l d ed sleeve. The back of the sleeve is a puff formed from gathers, over a tted c u f f .
The s ty le lines for the puff at the back, and the c u f f (M-PO-R to the cap l i n e ) are
drawn as
desired.
FIGURE 10A.
The
A straight underarm seam for the upper section is drawn from D to N. The f r o n t f o l d l i n e is straightened from M to the cap line.
In this sleeve, the seam of the c u f f runs down the back l i n e O-K, instead of
the
underarm.
Figure 10B
Figure 10A
The shaded sections of the sleeve are opened as explained in previous gures.
Line Q - P gathers to meet line O-P of the sleeve c u f f .
The c u f f is folded on line M- L, and the shaded section traced through. The seam line 0 - K can be closed by buttons, a zipper,
etc.
FIGURE IOBB. This gure shows the nished appearance of the sleeve.
Figure IOBB
,~
V a r i a t i o n s In
T h e Cap Of
T h e Sleeve.
Figure 13A
Line E- G-F is drawn any place above the elbow line, showing the level at which the fullness to be added to the sleeve cap will narrow down to the normal width of the sleeve.
Figure 13B
The two halves of the sleeve head are spread equal amounts on each side of the center l i n e .
The sleeve is cut on lines BG to points E and F. THE PIECES S H O U L D REMAIN ATTACHED TO T H E SLEEVE AT POINTS E AND F f o r ease in handling.
The shaded section between the points G indicates the extra length being added to the height of the sleeve cap at the same time.
FIGURE 13C. This is one way the new cap line f o r the sleeve can be drawn. The m a x i m u m width of the spread of the sleeve has been kept. A l i t t l e m o r e height has to be added to n i s h the curve of the cap.
The shaded section at the top of the cap plus the shaded section between points G make the t o t a l increase in height of the sleeve cap. This extra height enables the sleeve to stand up from the level of the shoulder like the old fashioned ''leg 0' mutton" sleeve, or stand out from the shoulder as a puffed sleeve. The sleeve fullness is gathered between points A-B-C to t the arm-
Figure 13CC
This gure shows nished appearance of the sleeve.
the
Figure 13C
. hole.
____ _
_.
Figure 14A
Figure l4AA
This gure shows the nished appearance of the sleeve.
This gure shows the same procedure as Figures 13A-C f o r a short sleeve.
The cap is shaped differently from t h a t in Figure 13C to show a possible variation. Here the n e w cap line is drawn to make the top of the sleeve narrower and with more height than t h a t in Figure 13C.
70
A d d i n g Pleats, Or
Darts,. 01: T u c k s , To
T h e T o p Of
T h e Sleeve.
J
2
2 2
)
Z
.3
3
-
*-
3 \
i
G
_L_B9v_v_
Figure 15A Lines 1, Z, 3 mark the places for the three darts which are to be made in this sleeve cap. These lines are continued to the l e v e l at which the fullness is to stop, line E-G-F.
(The sleeve in t h i s gure is shown drawn only to the elbow l i n e because the rest of the sleeve remains exactly the same.)
_|-LN__ _-J
----Figure 15B
'
The sleeve is spread so t h a t there are equal spaces between lines 1, Z, and 3, if that is the way the darts are to be. The extra height (between the points G) added to the sleeve determines the length of the d a r t .
Figure l5CC
This gure shows the nished appearance of the sleeve in Figure
15C.
Notice the n e w points 7 and 8. Line 4-7 is made the same length as l i n e 4-1. Line 6-8 is made the same length as line 6-3.
A n e w cap line is drawn from The cap l i n e between points 1-2 and 2-3 will have Ibbe reshaped to make a smooth cap l i n e when the darts are stitched. This is iclt done in the tting and transferred back to the pattern.
points 7 and 8 into points D.
Figure 15C
Figure l5D
FIGURE 15D. This gure shows the appearance of a sleeve with longer darts, spreading far enough apart to be individual points. For longer darts, the sleeve pieces are spread further apart so t h a t the space between the points G increases.
71
Figures 18A, 18B and l8BB show the construction of a sleeve with four d a r t s which are not p a r a l l e l to each other. They cannot be spread more than 1/2" at t h e bottom in t h i s construction (see Figures l5A- 15C).
-"
L-O is
the
Figure 18 BB
This gure shows the nished appearance of the sleeve.
Figure 18A Figure 183 FIGURE 18A. L-N is the combined length of the dart spaces 2-1 and 1-7. combined length of the dart spaces 3-4 and 4 - 9 .
FIGURE 18B. The dart sections are cut out and pivoted from points 5, M, and 6, making four even dart spaces. To complete the darts in this gure, the dart line must be drawn from 8 through N (8-P) for the same length as line 7-8. 10-O-Q equals 9-10.
In this type of sleeve the dart spaces cannot spread m o r e than about 1/2" at the bottom, otherwise points P and Q extend too far beyond the sleeve cap. New cap lines are drawn from P and Q into the cap lines at A and C.
Figures 19A and 19B show the construction of two other possible style variations.
lop
FIGURE 19A. A separate "box cap" can be drawn any shape desired, but O-M can be no longer than l i n e LM.
L-Q equals N-O.
M--S equals M-N. M-T equals M-P.
L-R
equals O-P.
The n e w cap lines are drawn from points S and T into the points D. Section M-N-OP-M is cut away as a separate section. In the tting, line 5- M-T is sewed to N- M~ P.
Figure 19
FIGURE l9AA. This gure shows the nished appearance of the sleeve.
to-
N- M-O.
Figure -19
I
f
FIGURE 19BB. This gure shows the nished appearance of the sleeve.
. _ . : _ : _ .
Figure 19B
74
Another variation possible on the a t or open sleeve is the cowl sleeve. See Cowl Necklines as w e l l . |
Figure 20A
The "cowl" l i n e s 1, 2, 3, 4, 5, 6 are drawn as deep and as far apart as desired. The shaded
extra fullness in the normal sleeve Figure 2013 cap can be removed. It is no longer necessary in a sleeve with cowl The sleeve sections are cut apart and spread fullness. as desired. The shaded sections can be c u t away first and the pieces rejoined at the cap. When spread, points E and F should be kept together. The top sections can be spread apart less than the bottom or all the sections spread evenly.
the
Figure 2033
This gure shows the nished appearance of
the sleeve.
H-I sews to I - J , making the inside fold of the top cowl. The shape of this l i n e can be adjusted in the tting.
Usually the sleeve is cut on the bias grain, as marked.
Figure 21A
Figure 21B
Figure ZIBB
FIGURES 21A, 21B and 21BB. These figures show another style variation included here because it illustrates the problem of inserting gathers in the middle of the head of the sleeve.
A center section HI- J-K has been kept a t just as a style possibility. Only the side sections have been spread to give increased width and length to the center of the head of the sleeve. 75
76
Page 89
Page 89
Page 93
Page 94
Page 94
\\
\\
Page 97
Page 98
\\
Page 99
Page 101
78
Figure 2A shows the positions of the basic patterns for a l l t t e d types of sleevewaist combinations.
The top cap l i n e of the sleeve is placed with the armholes of the waist patterns similar to the way it is sewed into them. It is then easy to combine the overarm part of the sleeve with the waist patterns. The excess fullness at the sleeve cap, which normally is eased into the armhole when sewed together, becomes a shoulder dart.
The underarm sections of the sleeve and the armholes are not changed. Any s tyl e l i n e drawn on the waist patterns must be joined to the sleeve p a t t e r n at approximately point D so t h a t it can continue into the normal underarm and sleeve cap lines.
Figure 2A
The sleeve pattern is marked on a sheet of paper. (Any type of style sleeve with a t t e d cap can be used.) The back waist pattern is placed on the sleeve so t h a t point D meets point I-1 and point C is raised l/4" above the sleeve cap line. The f r o n t waist pattern is placed on the sleeve in the same way. (The 1/4" allowance helps keep the waist armholes from overlapping the sleeve cap too much. As much as 1/2" can be allowed if necessary. )
The f r o n t and back shoulder lines B-C are brought together as a dart at point J, making a n e w shoulder line for the sleeve and waists. The point of the dart should curve enough below J to make a line which will follow the curve of the shoulder and top of the arm. This line is best adjusted in a cloth tting. Approximately, it can be drawn as shown here from the center of the shoulder lines to a point about 1/2" below point J. 80
Figure 3A D - Q and DR are style lines, drawn as d e sired, making "Raglan" style lines K-D-Q and E-D-Q, and M-D-R and E-D-R. Figure 3B
IS DRAWN MUST COME B A C K TO POINT D ON THE ARMH O L E OR WITHIN APPROXIMATELY O N E HALF INCH OF IT, to retain a closely tted underarm.
FIGURES 3B, 3C and 3D. These g ures show the pattern pieces traced separately from the construction diagram of Figure 3A.
Figure 3D
Figure 3C
81
Figure 3DD
FIGURE 3DD. This gure shows the cloth tting of the tted raglan sleeve pattern.
Figures 4A-4D show how the style lines of the t t e d raglan sleeve can be modified by moving the shoulder dart fullness to the armhole lines.
Figure 4A
This shows the s a m e sleeve as in Figure 5A, but shortened to the elbow line because the rest of the sleeve is not pertinent.
Figure 4B
The dotted l i n e is the center of the sleeve-shoulder d a r t B- J - B . H-5 and L-T are notch points within which the fullness in the armhole lines will f a l l . (The fullness should be placed in the area of the shoulder and top of arm c u r v e . ) The shaded shoulder sections should be t r a c e d through to another sheet of paper and c u t out.
The shaded sections which have been cut ,j out are placed back on the sleeve so that points J meet and points B come together on the central dotted l i n e .
4 . / "
This procedure opens two darts H-J-H and L J-L in the armhole l i n e s , replaci n g the shoulder dart B-J-B.
e a = e : . ; * : M
, , r
*/\'>'></\/Z7[Z/
/
FIGURE 4C. New armhole lines are drawn approximately as shown here. They can be adjusted in the cloth tting.
K-H and M-L on the new armhole lines are the same measurement as K-H and M-L of the o rig in al sleeve.
The n e w fullness (shown by the shaded spaces) is spread between points H and S and L and T. This fullness can be gathered, pleated, or tucked, as desired.
Figure 4C
82
FIGURE 4CC. This gure shows a cloth tting of the sleeve in Figure 4C, with the fullness laid in
pleats.
Figure 4 C C
Figure 4D
Figure 4DD
This gure shows another possibility. Here the shoulder dart B.T-B is only p a r t i a l l y closed, opening a smaller amount of fullness in the armhole. This fullness can be gathered, as shown in Figure 4DD. If the material used is of such nature, and the fullness is not too much, the gathers can be shrunk out leaving no v i s i b l e signs of the fullness. Only the shoulder d a r t would remain.
It is possible to swing a l l the fullness of the shoulder dart into only one armhole, either the f r o n t or the back.
all, pivoting
83
T h e F i t t e d D r o p p e d Shoulder S l e e v e
FIGURE 5A. The position of the basic pattern: is the sa.me as in Figures 2A and 2B.
The dropped shoulder style line O-P is drawn any way desired. (Usually it is not drawn any lower than points D on the armhole.) The shoulder dart lines are
continued through J to the n e w style l i n e (point Q).
Figure 5A
5A.
Figure 5AA
Figures 5B, 5C and SD show the pattern pieces traced separately from the construction diagram of Figure 5A. The dotted l i n e s show the procedure if a deeper
armhole l i n e is desired.
W
Figure 5D
FIGURES 5B and 5C. Both the f r o n t and back armholes must be lowered the same amount.
FIGURE 5D. The sleeve cap l i n e must be extended both f r o n t and back to match the n e w Figure /5B Figure 5C armhole lines on the waist patterns. A l i n e is drawn through points K and M as a guide for extending the cap lines. The curve of the new cap lines should approximate the shape of the n e w armhole lines, and must measure the s a m e length. (OT of the sleeve cap sews to O-R of the back armhole. PU of the sleeve cap sews to PS of the f r o n t armhole.) K-T and M-U should be the same size if possible. The shape of the armhole and sleeve cap lines can be n a l l y adjusted in the cloth tting. 84
A Fitted Y o k e A n d Sleeve C o m b i n a t i o n .
Figures 6A-6C show j u s t one of many possible t t e d yoke and sleeve combinations.
FIGURE 6A. The position of the basic patterns is the same as in Figures 2A and 2B.
Here
the yoke style lines are drawn into the waist d a r t s . They can be drawn any way desired. (Usually, the yoke line should not go lower than points D on the armhole.
The shoulder dart lines continued through J, down the center of the sleeve f o r whatever length sleeve is desired.
cL____
Figure 6A
gures
show
the
pattern
Figure 6B
Figure 6C
FIGURE 6AA. This gure shows the cloth tting of the patterns in Figures 6B and 6C.
Figure 6AA
85
A Fitted Y o k e A n d D e e p A r m h o l e C o m b i n a t i o n .
Figures 7A-7D show another one of many other style p o s s i b i l i t i e s of the t t e d sleeve and waist combination.
Figure 7A
The position of the basic patterns is the same as in Figures 2A and 2B.
In this gure a f r o n t yoke is combined with a. deep armhole (O-D-P). The back waist pattern has simply a deep armhole Q-R which matches
the f r o n t in depth.
F-R
equals F-P.
Point S is simply a notch on the front shoulder l i n e B-J marked off to match point 0 on the back.
FIGURE 7B. Only part of Figure 7A is shown here to avoid the confusion of too many lines.
The cap lines of the sleeve have to be lengthened to match the deep armhole lines on the f r o n t and back waist patterns. (See Figure 5D.) The n e w cap lines D-T and D-U are drawn to meet the guide l i n e through points K and M. D-T is drawn the s a m e length as the back armhole line D-R of Figure 7A, and similar in D-U matches the f r o n t armhole line shape. D-P in Figure 7A and should be similar in shape. Points T and U are joined to the sleeve at any depth desired. \\F
It should be noted here that T-K is longer than M - U because of the difference in shape between the f r o n t and back armholes. If it appears practical in the cloth tting, the side seam l i n e of the waist could be moved toward the back to h e l p make T-K and M-U equal so t h a t both sides of the sleeve are in balance.
Figure'7B
86
FIGURES 7C and 7D. These gures show the back and f r o n t waist patterns traced separately without the sleeve.
Figure 7D
Figure 7C
sleeve lines T-V and UW should be made the same length. Also, points T and U need not remain as sharp as they are. T They can be dropped and attened out because there is plenty of length in the underarm o f x \ the sleeve.
The dotted lines show how these changes can be made. D-X equals D-T. D-Y equals D-U. X-V equals Y-W.
The shape of these lines can be adjusted further in the cloth tting, if necessary.
Figure 7E
Figure 7 E E
This gure shows the c l o t h tting of the patterns in Figures 7C, 7D and 7E.
87
K i m o n o Type C o m b i n a t i o n Sleeves.
When the entire sleeve is joined to the waist, there is always the problem of raising the a r m comfortably. (See Figure 1F in the introduction to Sleeves.) More " l i f t " can be given to the underarm either by inserting a separate underarm section known as a "gusset, " or by providing enough extra length for the underarm of the sleeve in ' the construction of the pattern. The gusset gives extra length without extra f u l l n e s s . It is dif cult to set in and frequently rips out, but it does allow for a m o r e t t e d type of kimono sleeve.
When extra length is added to the underarm as in Figures 10A and 10B, more f u l l ness comes into the armhole. The shaded sections in Figures 8B and 10B should be compared. The a r m can be raised higher with no gusset piece, but there is m o r e excess fullness at the underarm.
G u s s e t T y p e K i m o n o Sleeves.
52
..
? * 2 : 'L ! . ',
m ~ v n s m : m m r _ m ~
Figure 8A
This gure shows the positions of the basic patterns f o r a l l gusset-type kimono combinations in relation to the t t e d type combination sleeves. This gure is based on Figure 2A of the t t e d type combination sleeves, which is shown here in dotted lines. It is d i f ferent from Figure 2A in t h a t both waist patterns have been swung away from the sleeve, (using points C as pivots), to keep the underarm lines of the sleeve entirely free from the waist patterns. This causes the extra fullness (shaded sections) at the armhole which is t y p i c a l of a l l kimono type sleeves. The shaded sections in Figure 8B show this more
c l e a r l y.
m m . m : 1 o m a . ~
i 3?
_.
88
The Basic Position Of The Waist And Sleeve P a t t e r n s For A l l Gusset-Type Kimono Sleeves
Figure 8B
The instructions for Figure 2A under Fitted Type Sleeves must be followed r s t .
The sleeve pattern can be marked in place, but the waist patterns should not be marked until the following instructions are completed. The back waist p a t t e r n is placed on the sleeve so t h a t point D meets point H and point C is raised 1/4" above the sleeve cap l i n e . Point C is pinned in position as a p i v o t so t h a t the waist p a t t e r n can be moved away from the sleeve u n t i l the side seam l i n e E~F meets the underarm point K of the sleeve.
The front waist p a t t e r n is moved in the same way until the side seam line E-F meets the underarm point M of the sleeve. The p a t t e r n s are marked in this position. The armhole lines of the waists and the sleeve cap l i n e are no longer of any use except as guide lines f o r the drawing of style lines.
89
Figures 9A-9K show various types of gussets which can be constructed to give "lift" to the underarm of the sleeve.
The larger the gusset, the more freedom of a r m movement. A balance must be struck between the small gusset which is invisible when the a r m is down and a gusset large enough for comfort when the a r m is raised. This can be achieved only through many trials with cloth ttings. (The gusset is usually cut on the bias grain to lessen the strain on the corners.)
The basic procedures outlined here are the same whatever the size and shape gusset desired.
Figure 9A
The front and back armholes must be cut into to allow the insertion of the Enough space must be c u t out to make r o o m f o r small s e a m allowances. The slash line_s must be drawn to s o m e outside edge of the waist and sleeve patterns.
gusset.
The front gusset slash lines UT-M meet the above requirements. The back gusset slash lines Q-R-S must be drawn to fall the same way on the side seam and the sleeve underarm as the front. K-S must measure the same as M-U. E - Q must measure the same as EM. Points R and T can be brought as high into the armhole as p r a c t i c a l . The higher the points, the higher the a r m can be raised.
In effect, new armhole and sleeve lines have been drawn. R - Q and T-M are the back and f r o n t armhole l i n e s . R-S and TU are the sleeve cap
lines.
90
wv
T
R
U,S
Figure 9C
Figure 9B
In this gure, the underarm gusset lines S-V and U-W a r e about 4" long. (About 1" to replace the sleeve underarm, plus 3" f o r " l i f t . ") Line T-W must be made the same length as line T-M. Line R-V must be made the same length as l i n e R-Q.
FIGURE 9C. Both the front and back halves of the gusset (T-U-W-T and R - S V-R) must be traced through from the construction in Figure 9B and joined t o -
U-W and S- V.
The armhole lines T-W and R-V must be placed on the same side. R-5 and T-U must be placed on the same side.
The sleeve
@\?
Figure 9AA
This gure shows the c l o t h tting of the p a t t e r n in Figure 9A.
91
Figure 9D
U,$
Figure 9E
the
FIGURES 9D and 9B. These gures show another gusset in which armhole l i n e s are shorter and the sleeve lines longer.
w,v
Figure 9F
R
T
u,s
Figure 9G
the armhole lines are longer and the sleeve lines shorter.
92
Figures 9H9K show how a gusset can be used in a short kimono type sleeve-
Figure 9H Figures 9JJ and 9KK should be studied first to understand this gure.
Line 1-2 is the length of the short sleeve and only part of the finished width of the sleeve at that l e v e l . Lines Q-R-1 and M-T-2 are the slash lines for the gusset. They can be drawn as desired.
Figure 91
The dotted lines show one type of gusset t h a t can be made to n i s h the short kimono sleeve.
Since l i n e 1-2 is too short to m a k e the nished width of the sleeve, the gusset must have part of the sleeve width allowed in i t . Lines X-V and Y - W of the gussets are part of the width of the sleeve. X-V plus 1-Z plus W - Y make up the complete width of the sleeve.
Lines Q - X and M - Y rnustbe the same length for they are the underarm of the gusset and the sleeve. These lines can be curved if desired, to blend m o r e smoothly i n t o the side seam of the waists. Line R-V must be the same length as R-1. Line T-W must be the s a m e length as T-2.
93
v
.
w
v
x
Figure 9J
The front and back gus sets should be traced separately, and are best kept t h a t way.
the sleeve.
Figure 9JJ
This gure shows the tting of the gusset in Figure 9J.
cloth
1'
v
~
Q"
)
M
F
Figure 9K
It is possible to make the sleeve gusset with no underarm extension at a l l , but have the width of the sleeve join directly to the side seam of the waists.
Points Q - V and M-W are joined directly by either a straight or curved l i n e blending smoothly into the sleeve line 1-2.
Figure 9KK
This gure shows the cloth tting of the gusset in Figure 9K.
Figure 9L
This shows a short kimono sleeve similar to that in Figures 91 and 9K, but without a gusset. It is m o r e d i f c u l t to raise the a r m comfortably in such a sleeve unless it is c u t very short.
FIGURE 9LL. This gure shows the nished appearance of such a sleeve.
/
Figure 9LL
94
Non-Gusset T y p e K i m o n o S l e e v e s .
W h e n there is no gusset to provide the extra underarm length needed to raise the a r m comfortably, the construction of the p a t t e r n i t s e l f must allow for i t . (See the introduction to Kimono Sleeves.)
Figure 10A
This figure is based on Figure 8A of the gusset type kimono sleeves which is shown in dotted l i n e s .
Both waist patterns are swung f u r t h e r away from the sleeve pattern to make room for m o r e underarm length. A center l i n e BJ is drawn between the two shoulder lines B-C. Using points C as pivots, the waist patterns are moved toward the center l i n e so that both shoulder points B meet on the center line. The patterns are marked in t h i s
position.
There is now more fullness at the armholes (shown by the shaded sections) than in Figure 8A.
95
Figure 10B
This gure is the basic position of the patterns f o r all non-gusset type kimono sleeves and is made
(The dotted shoulder lines B-C have been retained simply to make the position of the center l i n e B-J m o r e c l e a r. )
only as guide lines.
96
sleeve underarm lines can be joined with the waist pat t e r n s in various ways as shown here by the dott e d lines.
\ \
\
The front and back underarm lines should be drawn as nearly alike as possible. Differences in length can be adjusted l a t e r as shown in Figures 10Dl0F.
I /
I I
I
/
//
The n e w shoulder and sleeve l i n e can be drawn from point B down through the center of the sleeve, or any other way desired.
Figure 10C
F
Figure 10D
FIGURE 10D. This gure shows the back p a t t e r n with the deeper underarm from Figure IOC. FIGURE 10E. This gure shows the front pattern with the deeper underarm from Figure 10C.
IF T H E FRONT U N D E R A R M C U RV E IS N O T T H E S A M E LENGTH AS T H E BACK, IT MUST BE ADJUSTED TO M E A S U R E T H E S A M E ,
as shown in Figure 10F. dotted l i n e XY.)
(The adjustment can be made along the
97
Figure 101-:
Figure IOFF
This gure shows the cloth tting of the p a t t e r n s .
Figure 10F
FIGURE 10F. The f r o n t pattern pieces have been spread at point Y u n t i l l i n e W-F measures the same as line U-F of the back (Figure 10D). T H E FRONT A N D BACK BASIC PATTERNS USUALLY DO N O T JOIN T H E SLEEVE IN EXACTLY T H E S A M E WAY BECAUSE THEY H A V E DIFFERENT SHAPES AT THE ARMHOLES AND SIDE SEAMS.
It is better to l e t the patterns f a l l in r e l a t i o n to each o th er the way they were originally tted, and make the adjustments later. This preserves the original "swing" of the sleeve. (Refer to the introduction to S e t - I n Sleeves.)
Figure 10G
Figure 10G shows how the back elbow dart (U) can be closed by pivoting from a point (V) on the center seam line. This is poss i b l e only because the kimono sleeve has a bias grain and will stretch.
Figure 10H
98
Figure 101
These
another po ssib ility. The underarm seam can be lengthened so much that when the a r m is lowered a cowl-like effect is obtained. The back p a t t e r n is used here to illustrate how the underarm can be c u t and spread to add more length. The f r o n t p a t t e r n would have to be increased in the same way.
gures show
. YA
: . _ _ _ l
\ zvv
; 3\X
2
G
Figure 10J
/
a
Q
A
3
P
_1H
1"
//
__ ,c;I,|_lE / \
\
IIN I
__
\
\
\
R M
T
rest of the waist patterns, making a s o r t of yoke and sleeve combination. lines can be drawn any way desired. E - Q must equal E-R.
Figure 11A FIGURE 11A. In this gure, the sleeve and part of the bodice are removed from~ the
The style
99
_
#5?
; . * : " e
4.
Figure 11 B
Figure 1 1 C
FIGURES 11B and 11C. These gures show the back and front waist p a t t e r n s removed separately from the construction in Figure 11A.
W
:
Figure 11D
If desired, the sleeve underarm seams can be made " longer f o r even more"1ift.
Figure 11DD
This gure shows
the c l o t h tting of the p a t t e r n .
X1 must equal X-Q. Y-2 must equal Y-R. Points X and Y can be placed higher or lower as desired.
The underarm seams 1-U and 2W must equal each
o t h e r.
'
100
__ VI __ __
Figure 12A
__W
101
Figure IZB
Figure 12C
sections (shaded) should be traced through and c u t out. They can be pivoted from points 1 and 2 and moved up as much as desired to increase the underarm length
Figure 12D
of the sleeve.
In this procedure, the underarm lines Q-U and the same shape and length.
The armhole lines O-1-P and R-2-S should be rounded off at points I and Z. This may require an adjustment in length as shown.
FIGURES 12C and 12D. These gures show the back and front waist patterns removed separately from the construction in Figure 12A.
\\
Figure
IZBB
102
INDEX
TO
COLLARS
Flat Collars . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
---,pages 105-106
AND
SPECIAL
NECKLINES
Page 105
Rolled Collars
Page 106
Page 106
Page 107
Page 109
Page 111
Page 112
Rolled Collars
Page 113
Page 113
/
Page 114
R
Page 115 Page 116
103
Page 117
Page 119
Page 120
Page 120
Page 121
Cowl Necklines . . . . . . . . . .
\/
Page 123
Page 124
Page 126
Page 126
Page 127
104
F L A T COLLARS
Flat c o l l a r s follow the exact shape of the neckline. They f a l l a t from the neckl i n e without any standing r o l l . They are the simplest type of c o l l a r to construct.
FIGURE IA. The front and back waist patterns are placed together at the shoulder seam to give a continuous neckline.
'
4:
Point B of the back neckline meets point B of the f r o n t neckline. Point E of the back shoulder l i n e can rest on the extension of the front shoulder l i n e .
(I)
>+-
E.
I 2 0 3 ? !
The neckline of the c o l lar is the same as the neckline of the garment A-B-C. The style line is any shape.
Figure 1B
Figure 1A
Figure ICC
This gure shows a muslin tting of the c o l l a r. Any adjustments necessary for the c o l l a r to l i e absolutely a t should be made.
Any desired change in the style l i n e can be made on the tting. Sometimes it is more satisfactory to cut the c o l l a r wider than the desired nished width so t h a t the n a l shape of the style l i n e can be drawn directly on the tting.
A
Figure 1C
This is the p a t t e r n of the c o l l a r alone. The center back line is placed on a fold to make a complete c o l l a r. Point
B is the shoulder notch.
105
Figure 2B
Figure
ZBB
FIGURES 2A, 2B and ZBB. These gures i l l u s t r a t e another type of at c o l l a r, with a " V " neckline instead of a round one.
A neckline of any shape can be drawn, and the c o l l a r constructed around i t .
Figure 2A
FIGURE 3A. In this gure, a at c o l l a r is drawn to be convertible, that is, to l i e a t when the neckline is opened to form a lapel as well as when the neckline is closed.
D-E is the l a p drawn to allow for a button closing. F-G is the break or fold line of the lapel. The shaded s e c tion F-A-D-G is folded back on l i n e F-G and t r a c e d so that the neckline is in i t s open or lapel position. The neckline of the at c o l l a r is drawn following the shape of the neckline A-F-B-C.
g N
1'
ceursn
BACK
'
F R O N T
Figure 3A
F O L D
E
Figure 3B
,
FIGURE 3AA.
the muslin tting of the c o l l a r in both its open and closed positions.
Figure 3AA
106
R O L L E D COLLARS
Rolled c o l l a r s rise from t h e neckline of the garment f o r some determined height before folding over to rest on the shoulders. Rolled c o l l a r s can be divided into two types:
I.
Those in which the f o l d or break l i n e of the c o l l a r hugs the side and back of the neck as, for example, the shirt collar. Those in which the fold or break l i n e of the c o l l a r stands away from the neck.
II.
Figures 4A-4EE show t h e construction of the typical tailored shirtwaist collar. The fold line hugs the neck tightly. The center back depth of the c o l l a r is j u s t enough to cover the back neck seam.
FIGURE 4A. Point C is the center of the front neckline A-B. The dotted lines A-C and C-B are temporary construction lines. Line C-B is continued beyond the shoulder l i n e .
\'
\o \
The fold l i n e is as f a r from point B as desired f o r the c o l l a r to rise at the side of the neck before it folds back. (See Figure 5A f o r a different rise.) In this construction it is about 1 1/4".
B
D
C
\
E
A
FIGURE 4B and 4BB. The shoulder line D-B is extended to the E). E-F on the fold l i n e is the same measurement as the back neckline F-E in Figure 4BB.
{old l i n e (point
The shaded section represents the stand of the collar up to the {old or break
line.
C E N T E R F R
N T
T E R
EF N
Figure 4A
E C
K
Figure 4B
Figure 4BB
107
Figure 4C
This gure shows t h a t p a r t of the c o l l a r which f a l l s from the fold line to the shoulder.
Figure 4D
line
From point F a line (F G) is drawn at right angles to A-E-F for the center back of the c o l l a r. Line F-G should not be more than 1/2" deeper than the
stand of the c o l l a r.
The c o l l a r is now completed, folded over the stand, or shaded section, which cannot normally be seen
through the cloth.
Figure 4E
This is the finished c o l l a r p a t t e r n f o r one-half the complete c o l l a r.
If I F-G is not a straight line, the c o l l a r will have a seam at the center back. It is possible to draw a straight l i n e from I to G and place the c o l l a r on a fold. The dotted line from G to I to B shows the fold l i n e and the adjustment which needs to be made in the neckline for it to continue straight into the center back fold. When this is done, the f o l d l i n e becomes longer and the c o l l a r does not hug the neck so t i g h t l y.
Figure 4EE
This gure shows the muslin tting of the c o l l a r.
Sometimes the under c o l l a r is l e f t with a center back seam to maintain the good t and the top c o l l a r is cut on the fold since it has to be a. b i t larger anyway. (See Figures 51- and 5G. )
108
B .a\ B \
\ \
oA
\
\
D \
\\ \
I
\ \
I
I I
\ k
J "'-
In
Figure 5C
The stand of the c o l l a r must be opened to complete the c o l l a r p a t t e r n . The paper is folded under on the fold l i n e D- E-F, and the shaded stand sect i o n is t r a c e d through to the other side of the fold l i n e . The neckline of the c o l l a r has to be adjusted.
A smoothly curved l i n e is drawn from C i n t o the center back point I as shown by the dotted l i n e .
Figure 5D
The completed [collar pattern is traced C-BIF-G-H-A and through from AD' cut out. The collar is i l l u s t r a t e d in this position only to show how it ts into the front neckline. The lapel section is shown back in i t s original position.
The front facing is J-B-D-A around to L and K. (Refer to Figure 6D for f u r t h e r discussion on facings.)
Figure 5E
Figure 5F
FIGURES 5E and SF. The top c o l l a r always should be a t r i e larger than the under c o l l a r so that the
c o l l a r will roll over easily.
The center back of the top c o l l a r is a straight l i n e from G to I. G-I is lengthened up to 1/2" (depending on the fabric used) and a new neckline is drawn into point D as shown in Figure 5F.
Figure 5DD
This figure shows the muslin tting of the c o l l a r in its open position. W h e n closed, it would look like Figare 4EE.
Non-Convertible T y p e T a i l o r e d N o t c h Collars.
Figures 6A-6D show the construction of a tailored notch c o l l a r drawn to t i n t o a non- convertible l a p e l . The shape of the l a p e l is such that it must always be worn open. It cannot be worn closed around the neck since ' i t does not have the shape of the neckline.
The construction of the c o l l a r and l a p e l proceeds in the same way described in Figures 5A, 5B, and 5C.
Figure 6A
The construction of the stand and lapel follows the instructions in Figure 5A.
Figure 6B
Figure 6C
The lapel is immediately drawn in i t s nished position, from point D, any shape desired. The stand of the c o l l a r is narrower than t h a t in Figure 5A because the lapel has been drawn open wider at the
neckline.
FIGURE 6D. When the l a p e l remains open permanently, the facing must be m a d e larger than the l a p e l i t s e l f so t h a t the l a p e l can roll over on to the f r o n t easily.
Just as described f o r the c o l l a r in Figure 5F, the facing can be made up to 1/2" longer than the lapel, and abit
yvider, depending on the material, i. e. how well it can be eased in sewing and shrunk in pressing.
Lines J- BD M-N and the center front l i n e should be drawn first on another sheet of paper. The p a t t e r n can then be moved down on the center front line, up to 1/2". In this position the rest of the facing from N to L down the center front to K and back to J can be drawn.
added.
The dotted l i n e s are the finished l i n e s of the facing. They show how the increase in length comes out when properly
of the pattern.
T a i l o r e d S h a w l Collars.
Figures 7A-7C show the construction of the tailored shawl c o l l a r in which the c o l l a r and l a p e l form an unbroken l i n e from the center front to the center back neck.
The construction of the collar proceeds in the same way 5B, 5C and 6A6D.
as described
in Figures 5A,
Figure 7A
Figure - [ B
FIGURE 7B. The under c o l l a r section is shown separated from the lapel, and the l a p e l is opened as shown in Figure 6C.
the l a p e l can be cut in one piece with the top c o l l a r so t h a t no seam is v i s i b l e except at the
center back.
The c o l l a r and facing are kept joined at lines BDH. Extra length should be added to the collarlapel facing as w a s explained in Figure 6D.
T
Figure 7C
Figure 7BB
1 12
Stand Collars.
Figures 8A8CC and 9A9BB show the construction of collars which do not roll over at the neck, b u t consist of a, stand alone, joined to the lapel. The procedure is the same as described f o r Figures 6A, e t c .
The l a p e l can be drawn from any place on the f o l d line. Two different types of lapels are shown here, but any number of variations is possible.
At the back neck, the c o l l a r is j u s t a band collar, as shown in Figure 8CC.
Figure 8C
Figure 8A
Figure 8B
<3
F
Figure 8AA
Figure 8 C C
Figure 9A
Figure 9B 113
Figure 9 B B
T Y P E II
There are many variations in t h i s group of collars. Some collars have a slight, uniform r o l l from the center back to the center front; others r o l l away from back of the neck o n l y, lying a t at the f r o n t ; some are c u t in one with the center front waist. A l l the c o l l a r s are constructed basically in the s a m e way.
Figures 10A-10E show a c o l l a r with a slight roll around the entire neckline.
0 $04,? or
/Vgc/r
4' pC6,
F
9
Figure 10C
Figure 10A
Point C is the center of the front neckline A-B. A temporary guide l i n e is drawn from A to C. From point A a l i n e is drawn at right angles to A-C f o r the cent e r front l i n e of the neck.
Figure 1013
The center back l i n e of the back waist pattern is extended through point D f o r the center back of the neck.
F -G is the n e w neckline of the front c o l l a r. If the c o l l a r is to have a one-inch roll, that is, 1/2" up from the base of the neck and 1/ 2" down again, F-G must be drawn one inch above the neckline A- B.
R
FOLDBACK
F-G is drawn p a r a l l e l to the neckline A-B and the same length. The style l i n e of the c o l l a r (H-I-A) is drawn as desired. Points H and G are joined.
Figure 10E
Figure 10D
The new back neckline J-K is drawn in the same way as the front F-G.
the same length (The shoulder dart is ignored.) The style l i n e of the back collar is drawn as desired. Points K and L are joined.
The f r o n t and back c o l l a r sections are c u t out. The shoulder lines are placed together so that points G and K meet.
Any necessary adjustment in the style l i n e can be made.
Figure IOEE
This gure shows the muslin tting of the c o l l a r.
The shaded section is the depth of the roll or stand of the c o l l a r which turns down to meet the neckline.
114
Figures 11A-11D show a type of collar in which the roll of the collar is greatest at the center back, gradually narrowing u n t i l it disappears at the center front.
It is easier to construct the back of the c o l l a r r s t , since the back r o l l of the c o l l a r is the height to be determined.
Figure 1 1A
Line A-C is continued from the center back line f o r twice the desired rise of the c o l l a r. If the r o l l of the c o l l a r is to be 3/4" in depth, line A-C is made 1 1/2".
Line C-D is drawn at right angles to l i n e A-C and is made the same measurement as the back neckline A-B. The style line E-F is drawn as desired. Points D and F are joined.
Figure 11 B
Figure 11C
The neckline for t h e c o l l a r on the f r o n t waist p a t t e r n can be drawn as desired. In this gure the neckl i n e is a shallow " V " type neckline
The back section of the c o l l a r (Figure 11A) is cut out and joined to the f r o n t so that point D meets point I and l i n e D-F meets l i n e I-.].
If points F and J do not meet, the style l i n e of the c o l l a r can be adjusted as shown by the dotted l i n e .
'Ihe back neckline (D-C) can be redrawn so that it makes a better curve with the front neckline I-H as shown by the clotted l i n e . Because this removes some of the c o l l a r
G-H.
H-I is the new neckline of the f r o n t c o l l a r. I-I-I should measure the same as the neckline G-H. The distance from I to G is the same as the distance from D to B in the back collar (Figure 11A). G-J is
the same length as B-F of the back collar. Points I and J are joined.
points I, D.
Figure 11D
This shown the nished pattern f o r o n e - h a l f the c o l l a r. L-E is the center back fold.
Figure 1lDD
This gure shows
the muslin tting
The shaded section is the depth of the roll or stand of the c o l l a r which turns down to meet the neckline.
115
of the collar.
Figures 12A-12D show the construction of the s a m e type of c o l l a r as in Figures 11Al1D, except that the c o l l a r is shown cut in one piece with the front waist p a t t e r n . A f r o n t with an overlap f o r buttons is shown f o r variation.
z u r n c z r n n
I z O : I 'n
K cedure explained in
FIGURE 12C.
c u t out and
The completed c o l l a r H-I-L-E-K-F-H can be used as a separate c o l l a r. Line H-1 sews to the f r o n t neckline I-IG. Line I-L sews to the back neckline A- B. L-E is the center back f o l d of the collar.
FIGURE 12D. The collar is joined to the waist p a t t e r n by joining the collar neckline H-I to the front waist neckline H-G. M - N is the collar-front facing line (see Figures 7B, 7C). FIGURE IZDD. This gure shows the f r o n t and back of the muslin tting of the collar.
\
Figure IZDD Figure 12D
116
//
These gures show the same c o l l a r construction as in Figures 12A-12D. The neckline has been drawn lower than the normal neckline of the basic pattern just to show t h a t the construction of the c o l l a r remains the same wherever the neckline is drawn.
FIGURES 13A-13D.
Figure 13A
Figure 13B
Figure 13C
Figure 13D
Figure 13 CC
117
Figures 13E and 13F show a variation in the roll of the c o l l a r. To make the c o l l a r stand away from the neck even more than this construction allows, the r o l l l i n e can be increased in length by means of darts, or tucks, or gathers.
LINE
LINE
N E C K
N E C K
Figure 13E
The dotted lines 1, 2, 3, 4 show where the c o l lar is to be cut and spread for the increase in length. These lines can be drawn anywhere on the neckline depending on where the collar is to stand away from the neck.
Figure 13F
The lines are cut almost to the edge of the p a t t e r n and spread as m u c h as desired. Line 5, the center back line, cannot be spread. The same amount of fullness is added to i t . The spaces formed (the shaded sections) can be m a d e into darts, p l e a t s , tucks, or gathers, up to the roll line. The neckline of the collar is reduced to its normal size so that it will t into the neckl i n e of the garment. The r o l l l i n e retains its increased length.
Figure 1 3 F F
118
b.
A simple s t r i p hugging the base of the neck. A double c o l l a r consisting of a band c o l l a r plus a a t c o l l a r attached to the top of the band.
Figure 14B
The collar neckline is drawn as a curved line from points A to B, eliminating the corner at C.
Figure 14A
Point C is the center of the neckline A-B. C and A are joined by a line. C and B are joined by a l i n e which is extended through point B. From point A, a center front line f o r the collar is drawn at r i g h t angles to
line
The neckline of the band c o l l a r (A-D-E)_ equals the measurement of the front plus the back neckline: of the waist patterns. A-D equals the front neckline. D-E equals the back neckline.
desired.
A-C.
The c o l l a r can be drawn any width and shape Lines E-FG-A complete the c o l l a r.
F
E
0
Figure 140
Figure 14cc
This gure shows the muslin tting of the coua_r_
This is the pattern for onehalf the band The center back l i n e E-F is placed on a f o l d to make the complete
c o l l a r. c o l l a r.
119
FIGURES 15A, 15B and l5BB. These gures i l l u s trate one possible style variation of the band c o l l a r.
Y
G
E
Figure 15A
D
Figure 15B
'
Figure ISBB.
BAND
3
D
G
A
TOP COLLAR
Figure IGBB
3
Figure 16B
This gure shows the finished appearance of both collar patterns. Line F-G of the top c o l l a r is sewed to l i n e F-G of the band collar.
Figure 16A
I
Another c o l l a r GIH-F-G is drawn over the band c o l l a r. The top collar and band collar patterns must be c u t out separately,
The dotted curve from type of button extension which could be added to the band c o l l a r to be but toned at the center
A-B shows a
front.
120
Figures l7A-17D show the procedure which would have to be followed if a very deep top c o l l a r were desired.
J
H
Figure 17A
Figure 17B
Line HJ on the back waist p a t t e r n is the style l i n e of the back section of the collar. Line E-H isthe same m e a s u r e m e n t as the back depth of the c o l l a r E-H in Figure 1 7 A ,
The construction of the c o l l a r is the same as t h a t described in Figure 16A. The top collar is made as deep as desired. The shaded area of the top c o l l a r represents the back section of the c o l l a r. As constructed, it could not possibly t around the body. It must be widened to measure the same as the back waist pattern at t h a t
depth.
Figure 17C
Figure 17D
The top c o l l a r of Figure 17A is c u t out (G-A-I-JI-IF). The dotted lines show
of Figure 17A.
The top c o l l a r is cut and spread so t h a t l i n e H-1 is the same length as l i n e HJ of Figure 17B, PLUS l i n e .]-I
The nished collar pattern consist of the band collar pattern of Figure 17A (A-G-F-E-D-A) and the top c o l lar pattern of Figure 17D. Line F-G of the top c o l l a r sews to l i n e F-G of the band c o l l a r. The center back l i n e }:-E of the band c o l l a r is placed on a fold. The center back line F-H of the top c o l l a r is placed on a fold.
121
RAISED NECKLINES
The neckline of a garment can be moved higher up on the neck than the basic neckline making a finish for the neckline without a separate c o l l a r.
Figures 18A and 18B show the construction of the "neck" on which the raised neckline can be drawn.
CENTER FRONT
Figure 18A
Figure 18B
The center back line of the waist pattern is extended above the neckline through point E. The side line F-G is drawn p a r a l l e l to the center back
line.
(}.C,' is constructed in the
.-
from A to C.
Point C is the center of the neckline A-B. A l i n e is drawn The center front Line of the neck is drawn at right angles to l i n e AA-C. The side l i n e of the neck (B-D) is drawn parallel to the center front l i n e .
the human neck is not the same width from i t s base to the head, the side l i n e should be tapered l/4" about 1" above point B.
Because
F-G.
_
E
~
6
F
_.
Figure 1313
Figure l8BB
FIGURE 18B and l8BB. Any type of "raised neckline" can be drawn on the "neck". Figure 18B illustrates one type of neckline. Figure l8BB shows
Since the shape of the "neck" is approximated, n a l adjustments in the shape of the side of the neckline can be m a d e in the muslin tting.
122
COWL NECKLINES
T h e S i m p l e Neckline C o w l .
The cowl fold is con ned to the neckline only. It is not cut i n t o the body of the waist p a t t e r n as in l a t e r gures.
:_____2/
o ' =
Figure 19A
Figure 1.93
Line A-B is raised any amount desired f o r the cowl fold. Line A-B is the same length as l i n e A-B, and is the new neckline.
waist pattern.
If the center front is to be placed on a bias fold, point B is joined to the waistline C by a straight line. If a center front seam can be made, point B can be joined to the center front at any level (D), keeping the cowl fullness as close to the neckline as desired. The center front seam l i n e would be
B-D-C.
FIGURE 19BB. This gure shows the muslin tting of the cowl with a center f r o n t seam.
Usually a small weight is attached to point B to keep it down in its proper po sition.
Figure 19BB
123
T h e CenterFront-To-Shoulder C o w l .
A
Figure 20A
Lines 1, 2, 3 show where the cowl folds are to f a l l .
Figure 20B
The pattern is cut on lines 1, 2, 3 ALMOST to the shoulder seam. The pieces are spread as much as desired for the depths of the cowls. (The pieces must be b a r e l y attached at the shoulder so that they w i l l l i e absolutely a t when spread. ) The depth of the top cowl (3) is just added to the pattern as in Figure 19B. The new top l i n e (3) is made the same length as the old neckline (3). The center front fold l i n e is drawn from 3 to A. This l i n e should be placed on a. true bias fold. (See Figure 21C.)
Figure ZOBB
This gure shows the muslin t t i n g of the pattern.
124
Figure 21A
Figure 21B
The yoke l i n e A-B is drawn on the center front waist p a t t e r n . Points C and D are notches marked to help stitch the yoke and waist sections together correctly.
Line F-H is drawn to shift the waist dart E-F-G into the yoke line A-B. (See Figures 11E, 11F in the section on B u s t Darts.)
Lines 1, 2, 3 are the cowl lines.
The waist d a r t EF-G is closed, opening a small dart (H-F-H)which l a t e r can be gathered or eased into the yoke line.
Figure 21C
Figure ZID
Figure 21D is the same as Figure 21C except that the center front
The yoke section is cut away from the rest of the front pattern. Each of the cowl l i n e s (1, 2) are c u t from the center front ALMOST to the shoulder l i n e and spread as m u c h as desired.
In this illustration, the cowl spaces have been made different widths. The top cowl depth (3) is j u s t added to the pattern. The n e w line 3 is made the same length as the old.
If the center front l i n e of the yoke section can remain a seam l i n e , it can be drawn as a curved l i n e from 3 to B. This l i n e should be cut on a bias grain, as indicated.
l i n e of the cowl has been kept a straight l i n e so that it could be placed on a fold. To achieve t h i s it is necessary to lengthen the n e w l i n e 3 enough to meet the straight center f r o n t l i n e continued up from B. The n e w center f r o n t fold l i n e 3-B) should be made the same length as the o l d curved l i n e 3-B.
The square is drawn so t h a t part of the center f r o n t curve becomes the diagonal of the square. One side of the square becomes the straight grain l i n e , as shown by the arrows. (See Figure 21E.) 125
sum
V
B I A S
Figure ZIE
Figure ZIDD
This gure shows the muslin tting of the patterns in Figures 21B and 21D.
*
The center f r o n t fold is placed on a bias grain by making it the diagonal of a square, one side of which is the straight grain.
Figure 2 1FF
Figure 2 IF
FIGURES 21F and ZIFF. These gures show the same type of cowl construction as the previous gures, except t h a t here the cowl pieces are spread apart at the shoulder as well, allowing f o r pleats.
The cowl folds will f a l l from pleats on the shoulder l i n e , instead of from a smooth shoulder. This extra depth makes the cowls m o r e sharply de ned.
When the pleats are folded in place in the muslin tting, as indicated by the arrows, the shoulder l i n e should be the normal one in Figure 21A. Corrections can be made in the muslin and the p a t t e r n adjusted from i t .
126
T h e A r m h o l e - C e n t e r Front Cowl.
/
I
m o m
c a m : : n
Figure 22A
Figure ZZB
the construction of originates from the armhole line instead of the shoulder. The neckline has been kept normal. To i l l u s t r a t e something else that can be done, the center front is made with an extension for buttons.
s cowl which
Figure ZZBB
This gure shows the muslin tting of the p a t t e r n .
127
128
INDEX
TO
THE
APPENDIX
The Two-Piece Sleeve . . . . . . . . . . . . pages 131-132 Grading The Two-Piece Sleeve . . . . . . . . . .page 145
Cuffs . .
. . . . . . . . . . . . . . . . . . . . . . . . . . page
133
\\
\
0 L
Q
Page 132
Page 132
Pockets...
Page 134
Page 133
Page 133
Circular Ruf es
(
Page 135
Page 135
129
. . . . . . . . . pages
136- 144
130
T H E T W O - PIECE SLEEVE
The two-piece sleeve is a tailored sleeve limited today to suits and coats. It is a basic-style sleeve based on the folded one-piece sleeve, with separate overarm and underarm sections.
\
\
v
K
N
\\ \
\ \ \ \
F
1-:
E
Figure 1A
The one-piece sleeve is traced in i t s f o l d e d position. (See Figures 4A and 4B in the section on Sleeves.)
Figure 1B
The underarm section of the sleeve has no rigid dimensions. It can be varied as wished. The shape illustrated here is a good average one. The back underarm l i n e I-J-K is drawn as follows: I is the center of l i n e A-D. G-J is 1/2". E-K is 4". The f r o n t underarm l i n e L M-N is drawn as follows: L is the center of l i n e D-C. M-H is 1". N-F is 3/4".
The wrist measurement usually is widened enough for a hand to slip through. The back l i n e G-KE can be moved o u t to increase the width of the wrist. The new wrist line E-F usually measures 4 1/2"4 3/4". The new back l i n e G-E is drawn first. E-K is 4 inches. J-K is drawn.
131
|L
630
Figure 1C
Figure ICC
l
II
E
Figure 1D
Figure 1E
FIGURE 1C. The underarm section of Figure 1B is traced through separately from the rest of the sleeve. 1, 2, 3 are notches placed to aid in sewing. . .]'-1
is about 3".
M-Z is
about 2''.
FIGURE 1D. The folded sections (shaded) of the overarm section of the sleeve have to be opened. (The underarm section has been omitted from this drawing.)
Back: The paper is folded under on l i n e A- G. A-IJ is traced through. J-1 is the same measurement as J-l of the underarm section. J is joined to K.
Front: The paper is f o l d e d under on l i n e C-H. CL-M is traced through. The paper is opened a t and r e - f o l d e d on l i n e H-F. M-N is traced through.
M-2 equals M-2 of the underarm section.
section.
sleeve. The f o l d e d sleeve of Figure 1A can be cut on line GH and spread at point G another h a l f inch or so, as shown by the shaded section. The sleeve is now bent more at the elbow. The rest of the procedure follows as described
above.
0 O
FIGURES ICC and IDD. These gures show the underarm and overarm views
of the sleeve.
Figure IDD
132
CUFFS
Cuffs can be pieces cut to match the sleeve and stitched back on, similar to an outside facing. These are simply drawn from the a t sleeve.
The cuffs i l l u s t r a t e d here are separate from the sleeve, with their own shape. They are drawn in their nished position on the folded sleeve. (See Figure 4B of the section on Sleeves.)
.
. .
\
\ \
ix \
A
Figure 2A
B
Figure 2B
A
Figure ZBB
The cuff lines A-C-D-B are drawn any shape desired. This cuff swings away from the back of the sleeve (A-D) and will be opened there.
Line B-D is the front fold
The c u f f is opened by folding t h e paper under on the frontfold l i n e B-D, and tracing
through
D-C-A-B.
of the cuff.
A
Figure 3A
This cuff has a slight swing from the front and back of the sleeve (B-D and AC). The cuff is seamed or opened at the underarm E-F.
Figure 3B
The f r o n t section of the c u f f is opened by folding the paper under on line D-B and tracing through D-E-FB. The back section C-E-F-A is opened in the s a m e way.
Figure 3 B B
This gure shows the finihed a p pearance of the cuff.
133
POCKETS
All pockets stitched to the outside of the garment, or "Patch Pocket" types, can be cut any shape desired and stitched to the garment. They present no particular problem and so are not illustrated here.
"Inside Pockets can be separate pieces of material stitched to an inside seam or some slash l i n e . The type illustrated here is a special problem because it is part of the garment. It can be applied to a skirt as w e l l .
A P o c k e t Cut As
Part Of A Front W a i s t Y o k e A n d P a n e l S e c t i o n s .
Figure 4A
Figure 4B
'
The Yoke-panel Style lines are drawn as desired. A-C-B is the outside pocket ap. The dotted l i n e represents the inside pocket. (The bust dart can be moved O v e r to the Panel
line.)
The center front panel and yoke section (1) is traced through separately with the shape of the inside pocket joined to i t .
The side section (2) is c u t out separately a f t e r the ap of the pocket (A-C-B) has been opened a t from l i n e A-B. The dotted l i n e showing the shape of the inside pocket is kept f o r later use.
Figure 4C
The pocket ap and inside pocket are traced through from section (2) of Figure 4B. This makes the facing for the ap and onehalf the inside pocket. The ap facing A- CB is stitched to the ap A-CB of section (2). The curved pocket l i n e A-B is stitched to the curved pocket line A-B of section (1). The ap turns back. The opening of the pocket is in the straight line A-B.
Figure 4 B B
This gure shows the finished ap-
pearance
pocket.
of
the
134
CIRCULAR RUFFLES
Circular ruf es are circular ares and follow the same procedures. The one i l l u s t r a t i o n shown here can be applied to any loose, a r e d section of the garment such as: ounces, peplums, etc.
ure
D Figure 5A FIGURE 5A. The shaded section of the sleeve (A-BC-D) will be a circular-ruffle-cuff as shown in FigSCC.
Figure 5c
Guide
V/////////Av///////// _
B
Figure 5CC
.
FIGURE 5B. The section to be r u f e d (or ared) is cut away from the sleeve. lines are drawn (dotted lines) for cutting and spreading the section.
FIGURE 5C and 5CC. Each dotted l i n e is c u t ALMOST to the top line A-B. The sections are spread as m u c h as desired. In t h i s g u r e , line A-B becomes almost a com p l e t e circle. The circular l i n e A-B of the r u f e is stitched to the straight l i n e A-B of the sleeve. This forces the ares to f a l l into place as shown in Figure 5CC.
F D H
C
Figure 5D
FIGURE SD. A circular r u f e can be cut immediately as a circle, if that much fullness is desired. The procedure follows that described f o r the Circle Skirts, Figure 10A. Lines AE and A-D measure 1/6 the length of line A-B of the sleeve in Figure 5A. Line D - E should equal 1/4 the length of l i n e A-B. If it is too large, the l i n e can be raised a b i t to F- G. FGI-HF makes one-quarter of the complete r u f e .
GROUPS OF PLEATS (IN A SECTION OF THE GARMENT)
This is a supplement to t h e pleats shown in the section on S k i r t s .
FIGURE 6A. The pleats are folded r s t as they will appear ni shed in the paper to be used for the pattern. (1 and 4 are side pleats; Z and 3 are box pleats making one inverted center pleat.) The pattern section is placed over the folded pleats and marked in position. This can be done with any section of the garment. Here the sleeve p a t t e r n of Figure 6B of the section on Sleeves has been used.
FIGURE 6B. The p a t t e r n is cut out while the pleats are folded in position. The p a t t e r n is then opened a t , and the pleats notched f o r use. FIGURE 6BB. This gure shows the finished appearance of the p l e a t s .
$
Figure 6A
g
/ /
?
/
/I/2 ?3 /
/
/
\/
/ /
/
\
4
V
/
.
\
Figure
Figure 6B
6B3
135
A C O M P L E T E DRESS
This section summarizes some of the procedures which have been shown individually to make clear how a whole dress pattern is made and graded.
The grading procedure is based on the basic grading instruction in Book I on be referred to in order to understand the instructions below. The parts of that TOGETHER they grade the t o t a l amount shown for the basic patterns. p a t t e r n is to be increased, or decreased, as for example, a panel or a yoke,
Foundation Patterns, which MUST a style pattern must be graded so The amount each part of the style depends on the t o t a l effect desired.
B u t whatever the effect, no matter how many the parts into which a front waist pattern might be divided, the t o t a l measurement across the bust should increase or decrease no m o r e than the total grading measurement for the size. ex
the sketch of the be made in size 14 and graded to size 16.
<{
'
FIGURE 7B. The waist and sleeve patterns are placed in position f o r a t t e d yoke and sleeve combination, Figures 6A, 6B and 6C of the section on Fitted
'
1
, " "
\\
The c o l l a r is constructed according to the instructions for the c o l l a r in Figures 12A 12D of the section on C o l l a r s .
"
4
The sleeve is made to nish the length indicated by line 1. line 2) is added f o r the "push-up" effect.
If
Additional length ( t o
/;
desired, the bottom l i n e of the sleeve can be made a straight l i n e f o r ease in sewing and cutting. Some of the elbow dart fullness is l o s t , b u t t h a t is not too important in a sleeve of t h i s length.
Figure 7A
4?
- _.
_ . _ _ _ . .
Figure 7B
136
FIGURE 7C. This is the p a t t e r n f o r the center front section of the waist.
The c o l l a r is dotted because it is not part of the p a t t e r n . It is placed here only to make c l e a r how it is sewed on. (C-D of the c o l l a r will be stitched to the back neckline. )
'
shown by the
Figure 7C
F7
T h e Skirt Pattern.
II'
I
I"*~I
Pl-EAT
l<--1/8- '
-I
PLEAT
ures 4A-4C. )
FIGURE 7D. The completed f r o n t skirt p a t t e r n is shown here with i t s seam a l lowances. It is constructed according to the instructions in Figures 6A and 6B in the section on S k i r t s . (See also FigThe back skirt. is m a d e the same way.
FRONT SKIRT
out 2 mac:-:s
suzs
I4
The amount of grade necessary to go to size 14 is indicated. This follows the basic grading instructions in Book I f o r the skirt foundation patterns.
The necessary 3/8" at the waist l i n e is divided here to keep the pleats in relat i v e l y the same positions as the size increases. The center front panel is increased 1/8" in width. The rest of the measurement (1/4") can be placed a f t e r the l a s t loose pleat. This keeps the groups of pleats together as they are in the ori gi na l pattern.
<
"l/4
I
I
_ . ;
I I
I I
I I
''
I
I I I % I E
"
I I
I
I
I I
Figure 7D
<.|/8--->
T h e F r o n t W a i s t Patterns.
,-*"8
1/
---9
n"
<--I/I6--->A '16 \\
~'
3,416
F
.'/e
\\
3\/I6
r is <---3/I6-_-\\__,
CENTER \ FRONT WAIST-CUT 2 PIECES \ SIZE I4 _.
|{ *
I. I
\ N
'43
4
I
I
,'
I/I8
I/8
x\
='
@ <--|/e-> (D
Figure 8A
I I
FIGURES 8A and 8B. These are the completed front waist patterns with seam allowances.
The amounts the patterns are to be increased from size 14 to size 16 are indicated by the dotted lines and fractions. The measurements of both the center front and side front patterns must be considered together. Together they f o l low the measurements and instructions given for the grading of the f r o n t waist foundation p a t t e r n and one-piece sleeve pattern in Book I.
FIGURE 8C. The facing p a t t e r n is be s t graded by copying it d i r e c t l y from the graded center f r o n t waist p a t t e r n f o r each size, adding the extra length each time (as shown by the dotted l i n e s ) .
Figure 8C
138
I/I6
I/8
OUT I PIECE
T h e B a c k W a i s t Patterns.
SIZE I4
< -
I/8
4 i o
Figure 8D
Figure BE
FIGURES 8D and 8E. These are the completed back waist patterns with seam allowances. The procedure followed is the same as for the f r o n t patterns.
T h e Collar Pattern.
rH
_..'_.3_-
'i
}
I
I-<
COLLAR SIZE I4
7
OUT I PIECE
L _ _ _ _ _ _ . . . . _ _ _ _ _ . . _ _ _ J
Figure 8F
This is the completed c o l l a r p a t t e r n . Because the collar is a straight band, both the top and under c o l l a r s can be cut together as one piece, avoiding an unnecessary seam.
The c o l l a r grade has to follow the neckline grade. The back neck (1-2) increases 1/8". The p a r t that sews to the l a p e l (23) increases 1/8" as the lapel does.
139
away.
\\
C5)
Q]
(D
Figure 9A
\'_._
C avg)
Shifting T h e Pattern To
Increase T h e S i z e .
The p a t t e r n is shifted from point 1. The p a t t e r n is placed on the guide lines so t h a t point 1 of the p a t t e r n rests on point 1 of the guide lines and line 1-2 rests on l i n e I, Z, 3. A small corner is marked at point 1.
the same l i n e so that point 1 of the pattern meets point 2 of the guide l i n e s . The notch and a small portion of the l a p e l line are marked. PATTERN IS M O V E D up the sameline so that point 1 of the p a t t e r n rests on point 3 of the guide lines. The corner of the l a p e l is marked. PATTERN IS M O V E D up and away so t h a t point I of the p a t t e r n rests on point 4 of the guide lines. The beginning of the shoulder line is marked. PATTERN IS M O V E D away from point 4 so t h a t point 1 of the pattern rests on point 5 of the guide lines. The shoulder notch and a small portion of the shoulder and sleeve line are marked. P A T T E R N IS M O V E D down on the sleeve l i n e 3/16" and the corner at point 6 is
marked.
T H E PATTERN IS M O V E D across on
the bottom l i n e of the sleeve for 1/8". The corner at point 7 is marked and the corner at point 8. T H E P A T T E R N IS M O V E D so t h a t point I of the p a t t e r n rests on point 9 of the guide lines. The joining of the waist and sleeve are marked. T H E P A T T E R N IS M O V E D down on the s a m e line as 9 so t h a t point 1 of the p a t t e r n rests on point 10 of the guide lines. The corner of the waistline is marked. 140
SIZE I6
Figure 9B
The n e w pattern size 16 is completed by using the size 14 pattern as a. guide, centering it between the newly marked points, and drawing the completed l i n e s . The sleeve cap l i n e at point 8 is best drawn by placing point 8 of the size 14 p a t t e r n about l/8" away from the n e w point 8 and moving the pattern so t h a t the cap line blends smoothly i n t o the corner l i n e from point 9.
POINT 1 is
the side seam at the armscye, drawn on 3. vertical l i n e made longer than the side seam
line.
I\
3
POINT 2 is 1/3" above point 1 and 3/16" away from 1:. POINT 3 is 1/4" below point 2 and 1/16" away from i t .
Shifting T h e Pattern To Increase T h e S i z e .
guide l i n e s and the side seam of the p a t tern rests on the vertical line. The corner at point 1 is marked.
The p a t t e r n is shifted from point 1. Point 1 of the pattern is placed on point 1 of the
THE PATTERN IS M O V E D so t h a t point 1 of the p a t t e r n rests on point 2 of the guide lines. The corner of the armscye and yoke l i n e is marked.
\J
Figure 9C
THE PATTERN IS M O V E D so that point 1 of the p a t t e r n rests on point 3 of the guide l i n e s and the corner at the waistline is
marked.
@
is
T H E PATTERN IS M O V E D so t h a t point 1 of the pattern rests on point 4 of the guide l i n e s and the waistline at the side seam is marked.
Figure 9D
141
GRADING T H E B A C K WAIST P A T T E R N S
The back waist patterns are graded in exactly the s a m e way as the f r o n t waist patterns.
The shoulder d a r t in Figure 10B can be retained in the center between points 2 and 3, or it can be kept the same distance from point 2 in a l l the sizes.
Points 4, 5, 6 are marked without the use of the guide lines as explained for points 6, 7, 8 of the f r o n t .
-.5 CD 7
X\
<f
2 3,7
C5)
@
Figure 105
\
Figure 10C
@
'
CENTER_
BACK WAIST cur n PIECE
SIZE I6
6)
Figure 10B
142
Figure 1 OD
Two types of c o l l a r s are i l l u s t r a t e d below. Figures 11A and 11B show the grading f o r the dress p a t t e r n c o l l a r from Figure 8F. The grading problem is a simple one because the c o l l a r is a straight band. Figures 12A, 12B and 12C i l l u s t r a t e the special problem involved in grading the sharp curve of a a t c o l l a r, or any c o l l a r with a curved neckline.
Collars usually grade 1/2" in e n t i r e t y, or 1/4" f o r the h a l f c o l l a r. The back neckline of the c o l l a r usually grades 1/8", and the f r o n t neckline 1/8", corresponding to the grade of the f r o n t and back waist patterns. Usually, the width of the c o l l a r remains the same.
The c o l l a r p a t t e r n is folded in half for grading. When the grade is completed, the can be folded on the center back l i n e and the complete c o l l a r c u t o u t .
paper
is
C?)
:
Figure 11A
: ___
6)
A
(9
COLLAR SIZE I6
__
cut I PIECE
._
4_
_ __ __
r
1
J.
Figure 11B
tern is graded.
A l i n e is drawn (1) for the new center back fold line of the collar, from which the patLine 2 is drawn parallel to l i n e 1 and 1/8" away from i t .
The n e w c o l l a r is completed by joining the marked points with straight lines. The c o l l a r can then be folded in half on the center back fold line and the complete collar c u t out.
The collar p a t t e r n of Figure 8F (folded in half) is placed on the guide l i n e s so that the center back fold l i n e of the c o l l a r rests on the n e w center back f o l d l i n e . The width of the c o l l a r is marked by short l i n e s top and bottom.
T H E COLLAR PATTERN IS MOVED away so t h a t the center back f o l d of the c o l l a r rests on line 2. The shoulder notches both top and bottom are marked as well as short lines for the width of the c o l l a r.
l i n e 3.
t h a t the center
143
c o l l a r i l l u s t r a t e d in Figure
The extreme curve of the c o l l a r neckline makes it dif cult to get the proper 1/4" grade working just from the center back f o l d line as above. The grading will have to be done in two p a r t s , from the center back and from the dotted line at the front part of the c o l l a r.
Figure 12A
ure l1A. The c o l l a r is shifted from 1 to 2 in the s a m e way. The shoulder notch at 2 is marked, and a portion of the neckline a bit a beyond the dotted line. The dotted line is marked as well as portion of the outside edge of the collar.
A new guide l i n e (3) is drawn p a r a l l e l to the dotted line and 1/8" away from i t .
'
The c o l l a r is shifted so t h a t the dotted l i n e of the c o l l a r r e s t s on the new l i n e 3, meeting at the neckline. The shape of the end of the c o l l a r is outlined.
Figure IZB
the
Points 1 and 2 of the size 14 c o l l a r are centered between points 1 and 2 of the new c o l l a r. The back neck curve is drawn. Points 2 and 3 of the size 14 collar are centered between points 2 and 3 of the new c o l l a r. The f r o n t neck curve is drawn.
COLLAR SIZE IS
Figure lZC
144
- _ _ .
'
I/I6
V I/I6
->
..2
I'
42
..3
"
\/\6
,,
N
E
{/I/I6
Figure 13B
Figure 13A
(The dotted curve and straight line show the l e v e l of the underarm section.)
Part of the sleeve cap belonging to the underarm is s t i l l attached to the overarm section of the sleeve (points land L). These areas grade only half the usual amount, or 1/16". The rest is given to the underarm section. One1/16",
The underarm section increases 1/16" on each side of the center line to nish the sleeve cap measurement and the width aC r o s s the sleeve bicep.The wrist l i n e E-N increases 1/16". or half the wrist grade.
145
'ign Depunmena of the Cemnl High School of Needle Trades. He had been the rst gn-ment design teacher in 'mk City _:hou|s .md'I.\id the foundations nix .n|l subsequent teaghing in the eld.)
Jr;
d}: ted from Emoklyn College trained to teach Biology, but the country was deep in a dc~ on in 1933, gndc _' York City needed no teachers. For want of work, she spent the summer hefping her ynwrite his es: (text book an pmernmaknng. (Charles Kaplan was then chairma_n of the Womens Garment
ifwas g
,fh%t|/:',pro\'ed fascjnanng and Mrs Pnmd. begun her c.Irccr. zcachmg p.\uernmnk-ing .1! the Traphagen Sdnool Q pshmn in Ncw'York City. writing 4-idumml hooks. md working on Sex:-nrh Avenue" mia pmernmaker.
Her long, \_'aricd experiences proud: A umquc l'u<k;_-nuund fur U19 wnring of uiKablc For the L'l.Issroom as well 1: fm pmresuinnml me
a.
.|
text which
646:. 404
PIVN