Академический Документы
Профессиональный Документы
Культура Документы
Hu Mingchao
www.huawei.com
Huawei Confidential
Strategy 3
Strategy 4
Huawei Confidential
Page 2
Strategy 2 (Recommend)
F2 F1
R99+HSPA R99+HSPA R99+HSPA R99+HSPA R99+HSPA R99+HSPA
Strategy 3
F2 F1
R99+HSPA
R99+HSPA R99+HSPA
R99+HSPA
R99+HSPA
R99+HSPA
R99+HSPA
Strategy 4
F2 F1
R99+HSPA R99+HSPA R99+HSPA R99+HSPA R99+HSPA R99+HSPA R99+HSPA
Huawei Confidential
Page 3
Strategy 3
Strategy 4
Huawei Confidential
Page 4
Strategy 1
UE with Idle Mode Strategy UE with Connected Mode Strategy Parameters configuration
Huawei Confidential
Page 5
F2
HSDPA+R99(Barred)
R99+HSDPA
R99
R99+ HSDPA
F1
Strategy 1:
F2 cell is barred to force UE to camp on F1 in idle mode. After service released in F2 cell, UE come back to F1 cell. when UE hang up in F2 cell, maybe UE will display no service for a short time because F2 is barred.
Huawei Confidential
Page 6
Strategy 1
UE with Idle Mode Strategy UE with Connected Mode Strategy Parameters configuration
Huawei Confidential
Page 7
F2 HSDPA Cell change between intra-freq cells if there exists continuous F2 coverage.
In hotspots, HSDPA calls are DRD from F1 to F2.
HSDPA users DRD from F1 to F2
F2 F1
R99+HSDPA R99
Huawei Confidential
Page 8
Intra-freq HO to DCH
DRD to F2 to HSDPA
Huawei Confidential
Page 9
Scenario B:
Step1:HSDPA terminals camp on F1; Step2:HSDPA service DRD from F1 to F2 and established on F2 finally; Step3:Combined HSDPA+CS will be remained on F2; Step4:If CS service released, HSDPA service remain in F2 OR If HSDPA service released, CS service remain in F2;
HUAWEI TECHNOLOGIES CO., LTD. Huawei Confidential Page 10
Strategy 1
UE with Idle Mode Strategy UE with Connected Mode Strategy Parameters configuration
Huawei Confidential
Page 11
R99+HSDPA
R99+HSDPA
F2
R99+HSDPA
R99
R99
R99+HSDPA
F1
Huawei Confidential
Page 13
R99+HSDPA
R99
R99
R99+HSDPA
F1
MOD CELLALGOSWITCH: NBMLdcAlgoSwitch=UL_UU_LDR1&DL_UU_LDR-1; MOD CELLLDR: CellId=xxxx1, DlLdrFirstAction= BERateRed, DlLdrSecondAction= NoAct, DlLdrThirdAction= NoAct, DlLdrFourthAction=NoAct, UlLdrFirstAction= BERateRed, UlLdrSecondAction= NoAct, UlLdrThirdAction=NoAct;
RNC
MOD CELLHSDPA: CellId=xxxx2, AllocCodeMode=Manual, HsPdschCodeNum=1, HsScchCodeNum=2;CodeAdjForHsdpaSwitch=OFF; SET MACHSPARA: LOCELL=xxxx2, DYNCODESW=OPEN;
Huawei Confidential
Page 15
value.
ADD CELLINTERRATHOCOV: CellId=xxxxx2, InterRatReportMode=PERIODICAL_REPORTING, InterRATCSThd2DEcN0=-24, InterRATR99PsThd2DEcN0=-24, InterRATHThd2DEcN0=-24;
DEA CELLHSDPA:CELLID=xxxxF1;
Huawei Confidential
Page 16
Disadvantage
Lots of DRD attempts for HSPA service; Only F2 can carry HSPA service; Load is not balance between F1 and F2.
Huawei Confidential
Page 17
Strategy 3
Strategy 4
Huawei Confidential
Page 18
Strategy 2 (Recommend)
UE with Idle Mode Strategy UE with Connected Mode Strategy Parameters configuration
Huawei Confidential
Page 19
F2
HSDPA+R99
Strategy 2:
Camp on F1 or F2 randomly
R99+HSDPA
R99+HSDPA
R99+ HSDPA
F1
Huawei Confidential
Page 20
Strategy 2 (Recommend)
UE with Idle Mode Strategy UE with Connected Mode Strategy Parameters configuration
Huawei Confidential
Page 21
HSDPA+R99
HSDPA+R99
R99+HSDPA
R99+ HSDPA
R99+HSDPA
R99+ HSDPA
Huawei Confidential
Page 22
F2
F1
R99+HSDPA
R99+HSDPA
R99+HSDPA
Load balance between F1 and F2 in hotspots by DRD or LDR. R99 users can configured BE reduction as the first LDR actions.
Name LdbDRDOffsetDCH
Parameters introduction The threshold of remanent load offset between the current cell and the target cell when load balancing DRD is applied for DCH users. Recommended value: 5% (SET DRD) The threshold of remanent load offset between the current cell and the target cell when load balancing DRD is applied for HSDPA users. Recommended value: 5% (SET DRD) The inter-frequency neighboring cell could be selected as the destination of load handover only when its load remaining space is larger than this threshold. Recommended value: 20% (ADD CELLLDR)
Notes: DRD and LDR will be introduced in detail in Load Control slides.
HUAWEI TECHNOLOGIES CO., LTD. Huawei Confidential Page 23
Strategy 2 (Recommend)
UE with Idle Mode Strategy UE with Connected Mode Strategy Parameters configuration
Huawei Confidential
Page 24
Huawei Confidential
Page 25
ADD INTERFREQNCELL: CellId=1, RncId=1, NCellId=2, SIB11Ind=TRUE, SIB12Ind=FALSE, TpenaltyHcsReselect=D0, BlindHOFlag=TRUE, NPrioFlag=FALSE; ADD INTERFREQNCELL: CellId=2, RncId=1, NCellId=1, SIB11Ind=TRUE, SIB12Ind=FALSE, TpenaltyHcsReselect=D0, BlindHOFlag=TRUE, NPrioFlag=FALSE;
R99+HSDPA R99+HSDPA
F2
R99+HSDPA
R99+HSDPA
R99+HSDPA
R99+HSDPA
F1
Huawei Confidential
Page 26
R99+HSDPA
R99+HSDPA
R99+HSDPA
R99+HSDPA
F1
MOD CELLALGOSWITCH: NBMLdcAlgoSwitch=UL_UU_LDR1&DL_UU_LDR-1&CELL_CODE_LDR-1&CELL_CREDIT_LDR-1; SET CORRMALGOSWITCH: ChSwitch=DCCC_SWITCH-1, HspaSwitch=HSUPA_DCCC_SWITCH-1; MOD CELLLDR: CellId=0, DlLdrFirstAction=CodeAdj, DlLdrSecondAction=BERateRed, DlLdrThirdAction=InterFreqLDHO, DlLdrFourthAction=CSInterRatShouldBeLDHO, UlLdrFirstAction=BERateRed, UlLdrSecondAction=InterFreqLDHO,
RNC
MOD CELLHSDPA: CellId=xxxx2, AllocCodeMode=Manual, HsPdschCodeNum=1, HsScchCodeNum=2;CodeAdjForHsdpaSwitch=OFF; SET MACHSPARA: LOCELL=xxxx2, DYNCODESW=OPEN;
Huawei Confidential Page 28
value.
ADD CELLINTERRATHOCOV: CellId=xxxxx2, InterRatReportMode=PERIODICAL_REPORTING, InterRATCSThd2DEcN0=-24, InterRATR99PsThd2DEcN0=-24, InterRATHThd2DEcN0=-24;
Huawei Confidential
Page 29
Disadvantage
Both F1 and F2 can establish and carry on HSPA service. Balance load between F1 and F2
R99 and HSPA service establish in same cell, it would bring service interference each other, and it should be affect the call drop of AMR. F2 should be covered in a large continuous area, otherwise it is not good feeling for AMR when the CS users hard handover between the inter frequency.
Keep DRD attempt in low quantity and it is good KPI for access.
Huawei Confidential
Page 30
Strategy 3
Strategy 4
Huawei Confidential
Page 31
Open the LDR algorithm, and set the LDR action as following:
The SPG for R99 is same for F2&F1 The SPG for HSPA on F2 is higher than F1. OFF
Uplink: BE reduction->interFreq load HO->CS inter-RAT load HO Downlink: Code Adjustment> BE reduction->inter-Freq load HO->CS inter-RAT load HO
IRAT HO
Access DRD
F1 &F2 configure intra-Freq Neighbor each other; F1 and F2 configure blind HO neighbor each other for the co-coverage cell, but not HO based coverage; F2 configure inter-Freq unidirectional neighbor to F1 in the border covered by F2; F1& F2 configure the GSM neighbor cell, and GSM congfigure the F1 neighbor cell.
Huawei Confidential
Page 33
Huawei Confidential
Page 34
ADD INTERFREQNCELL: CellId=1, RncId=1, NCellId=2, SIB11Ind=TRUE, SIB12Ind=FALSE, TpenaltyHcsReselect=D0, BlindHOFlag=TRUE, NPrioFlag=FALSE; ADD INTERFREQNCELL: CellId=2, RncId=1, NCellId=1, SIB11Ind=TRUE, SIB12Ind=FALSE, TpenaltyHcsReselect=D0, BlindHOFlag=TRUE, NPrioFlag=FALSE;
R99+HSDPA R99+HSDPA
F2
R99+HSDPA
R99+HSDPA
R99+HSDPA
R99+HSDPA
F1
Huawei Confidential
Page 35
R99+HSDPA
R99+HSDPA
R99+HSDPA
R99+HSDPA
F1
MOD CELLALGOSWITCH: NBMLdcAlgoSwitch=UL_UU_LDR-1&DL_UU_LDR1&CELL_CODE_LDR-1&CELL_CREDIT_LDR-1; SET CORRMALGOSWITCH: ChSwitch=DCCC_SWITCH-1, HspaSwitch=HSUPA_DCCC_SWITCH-1; MOD CELLLDR: CellId=0, DlLdrFirstAction=CodeAdj, DlLdrSecondAction=BERateRed, DlLdrThirdAction=InterFreqLDHO, DlLdrFourthAction=CSInterRatShouldBeLDHO, UlLdrFirstAction=BERateRed, UlLdrSecondAction=InterFreqLDHO, UlLdrThirdAction=CSInterRatShouldNotLDHO;
RNC
Huawei Confidential
Page 37
7. Cell reselection make UE camp on F1 cell in advance by setting the threshold and offset for inter-frequency cell reselection in idle mode.
F1: MOD UCELLSELRESEL: CellId=xxxxxx, IdleSintersearch=0; F2: MOD UCELLSELRESEL: CellId=xxxxxx, IdleSintersearch=9; F1->F2: ADD INTERFREQNCELL: RncId=x, CellId=xxxxx, NCellRncId=x, NCellId=xxxxx, IdleQoffset1sn=50, IdleQoffset2sn=50; F2->F1: ADD INTERFREQNCELL: RncId=x, CellId=xxxxx, NCellRncId=x, NCellId=xxxxx, IdleQoffset1sn=-50, IdleQoffset2sn=-50;
Huawei Confidential
Page 38
Disadvantage
The interference is small between the HSPA service and the AMR. It should be good feeling for R99 service when F2 is not continuous coverage, because the R99 service does not hard handover in this area.
The HSPA accessibility should be affect by the DRD. The HSPA call drop should be increase when HSPA service move with the hard handover in these not continuous coverage area for F2. PS call drop should be increase when opening the function of state transition.
Huawei Confidential
Page 39
Strategy 3
Strategy 4
Huawei Confidential
Page 40
Cell reselection make UE camp on F1 cell in advance by setting the threshold and offset for inter-frequency cell reselection in idle mode . Or forcibly campF2 cell is barred to force UE to camp on F1 in idle mode. (not recommend)
Open the LDR algorithm, and set the LDR action as following:
Uplink: BE reduction->interFreq load HO->CS inter-RAT load HO Downlink: Code Adjustment> BE reduction->inter-Freq load HO->CS inter-RAT load HO
Load balance DRD offset for HSDPA: 5 Load balance DRD power remain threshold for HSDPA :90
Huawei Confidential
Page 41
IRAT HO
Access DRD
F1 &F2 configure intra-Freq Neighbor each other; F1 and F2 configure blind HO neighbor each other for the co-coverage cell, but not HO based coverage; F2 configure inter-Freq unidirectional neighbor to F1 in the border covered by F2; F1& F2 configure the GSM neighbor cell, and GSM congfigure the F1 neighbor cell.
Huawei Confidential
Page 42
Disadvantage
The R99 service does not hard handover in not continuous coverage area for F2; The resource of two carriers should be used fully.
There are half HSPA users on F1, and it will interfere the AMR users.
The accessibility should be affect by the half users DRD It should be ease congestion in F1 when there are many traffic for R99 in F1, and it is bad feeling for HSPA service in F1. PS call drop should be increase when opening the function of state transition.
Huawei Confidential
Page 43
Thank You
www.huawei.com