Академический Документы
Профессиональный Документы
Культура Документы
Signaling capability
UMPTa1 UMPTa2 UMPTb1
Transmission
RAT support
For UMTS only in SRAN7.0. It can support GUL Multi-mode in SRAN8.0. Same hardware with UMPTa2. For LTE only in SRAN7.0. It can support GUL Multi-mode in SRAN8.0. Same hardware with UMPTa1. Release in SRAN8.0, support GUL con-current mode. Same specification with UMPTa1/UMPTa2 in SRAN8.0
Signal: 1500CNBPA/s+ transmission: 1.5Gbps(UL+DL) SRAN7.0: 60 CAPS SRAN8.0: 120 CAPS GSM only: 72 TRX UMTS only: 1500CNBAPs LTE only: 120CAPS 1.5G bps(UL+DL)
1.5G bps(UL+DL)
UMPTa6
UMPTa6 embedded GPS while UMPTa1/UMPTa2 has no GPS embedded. UMPTa6 is mainly used for LTE TDD or with GPS requirement.
Page 2
N*WBBPb/d
N=1 N=1 N=1 N=2 N=2 N=3
N*WBBPf
N=1 N=2 N=3 N=1 N=2 N=1
Page 3
LBBPd
Cell Configure
GTM Strategy
LBBPd1 LBBPd2
Globally GTM for 3x20M 2T2R and can not be used for any 6cell/sector Scenario. Globally GTM for 3x20M 2T4R/4T4R and can not be used for any 6cell/sector Scenario.
Page 4
2. GUL 3 mode in 2 BBUs for co-transmission, coIpsec or co-synchronization 3. 2 BBUs in same cabinet manage the site coordinately
Only 1 UCIU board is configured in a BBU and is inserted in slot 4. GTMU must be inserted in the same BBU with UCIU. UCIU always inter-connected with UMPT
BBU0 BBU1
FAN WBBP
GTMU WMPT
PWR
PWR
Page 5
Triple-mode BBU(inter-connected)
For existing site, UCIU is used in the existing BBU and UMPT is used in the expansion BBU. The BBU with UCIU is primary BBU, while the other BBU is secondary BBU GTMU(if used) must be inserted in the same BBU with UCIU. The UCIU is inserted in slot4.
1)GSM&UMTS + LTE
UCIU F A N WBBP GTMU WMPT UPEU UPEU
2)GSM<E + UMTS
UCIU F A N LBBP GTMU LMPT UPEU
UPEU
F A N LBBP
UPEU UPEU
F A N WBBP
UPEU UPEU
UMPT(L)
UMPT(U)
3)GSM&UMTS + UMTS<E
MRRU
UCIU F A N WBBPf GTMU WMPT UPEU UPEU
1800M
F A N
UMPT(L) UMPT(U)
UPEU
More info to scenario3) GU+UL: 1. Both BBUs need insert WMPT or UMPT due to WMPT in BBU0 cant manage the WBBP in BBU1 2. Two interconnection cable are recommended to connect UCIU in BBU0 and 2 UMPT in BBU1 in order to get synchronization and other info. 3. WBBPf can be interconnected between 2 BBUs in order to configure BB resources in BBU1 if Radio unit connect to BBU0, and vice versa. WBBPd dont support interconnection. There is at least 1 WBBPf in each BBU to implement interconnection 4. Different kinds of WBBPs in 1 BBU can be Mixed
Page 6
UTRPc Board
The UTRPc is available as of GBSS14.0/RAN14.0/eRAN3.0/SRAN7.0. The UTRPc performs the following functions: Provides transmission for the GSM, UMTS, and LTE networks and enables theses networks to share the same IPSec tunnel. Supports co-transmission over the GSM, UMTS, and LTE networks, without the transmission of one affecting that of another. Enhances the signaling processing capability of the UMTS network.
Page 7
Connector
SFP RJ45
Quantity
2 4
Description
FE/GE optical ports FE/GE electrical ports
The UTRPc board shall be configured in the same BBUas the main control board that manages it. The UTRPc board can support co-transmission between a maximum of two BBUs Only one UTRPc board can configured in any from slot to slot5. In GU+L scenario the UTRPc board shall be configured in slot0 or slot1 of the root BBU, or slot4 or slot5 of the leaf BBU. The priority for slots goes slot0>slot1>slot4>slot5
Page 8
Thank you
www.huawei.com
Copyright2011 Huawei Technologies Co., Ltd. All Rights Reserved. The information in this document may contain predictive statements including, without limitation, statements regarding the future financial and operating results, future product portfolio, new technology, etc. There are a number of factors that could cause actual results and developments to differ materially from those expressed or implied in the predictive statements. Therefore, such information is provided for reference purpose only and constitutes neither an offer nor an acceptance. Huawei may change the information at any time without notice.