Академический Документы
Профессиональный Документы
Культура Документы
Section-I Section-II Section-III Section-IV Section-V Section-VI Section-VII Section-VIII Welding Terminology Welding Safety Welding PPEs and Hand Tools Welding Joints and symbols Important Arc Welding Processes Welding Consumables Welding Imperfections Duties of Welding Inspector
Section-IX
Section-I
Welding Terminology
1: Welding: Welding may be described as a metal working process in which metals are joined by heating to the melting point and allowing the molten portions to fuse or flow together. 2: Weldability The capacity of a metal to be welded easily is called weldability. 3: ARC A comparatively low voltage electrical discharge through a gas, between spaced electrodes. Basically there are three kinds of Arc 1) Arc due to direct current 2) Arc due to alternating current 3) Arc due to pulse current Direct current is further divided into DCSP and DCRP.
Welding Terminology
4: DCRP: In this case electrode is negative and base metal is positive. 2/3 heat is produced at the base metal and 1/3 at the electrode. 5: DCSP: In this case electrode is positive and work piece is negative. 2/3 heat is produced at the electrode and 1/3 at the base metal.
Section-I
6: ARC Welding: A group of welding processes which produce coalescence of metals by heating with Arc or Arcs, with or without the application of pressure and with or without the use of filler. 7: Gouging & Air Carbon Arc Cutting An arc cutting process that melts base metal by the heat of a carbon arc and removes the molten metal by a blast of air.
Welding Terminology
Section-I
8: Arc Blow: An electric current flowing through the electrode sets up magnetic field in a continuous series of circles in a plane perpendicular to the axis of the rod. Similarly magnetic lines are also formed around the work piece and ground cables. When the fields around the work piece or around the electrode are unbalanced, the arc bends away from the greater concentration of the magnetic fields. This deflection of the arc from its intended path is called Arc Blow.
Section-I
Welding Terminology
11: Deposition Rate: Deposition rate is the weight of metal deposited in a given period of time, usually expressed in kg/hr. 12: Deposition Efficiency: Electrode deposition efficiency is defined as the ratio between deposited and melted weight of the electrode. 13: Shielding Gas: Protective gas used to prevent atmospheric contamination. Argon, Helium & Carbon dioxide are commonly used as shielding gases. . 14: Operation Factor: It is defined as the proportion of the total welding time an operator is actually fusing electrodes.
Section-I
Welding Terminology
Process SMAW GTAW Deposition Rate % 60-75 90-100 Operation Factor % 20-30 20-30 50 for Semi Auto m/c 100 for Auto m/c 50 for Semi Auto m/c 100 for Auto m/c 50 for Semi Auto m/c 100 for Auto m/c
GMAW
90-95
FCAW
85-90
SAW
95
Section-I
Welding Terminology
15: Dilution: Thus the dilution is defined as a change in composition of a welding filler metal caused by the admixture of the base metal or previously deposited weld metal in the deposited weld bead. 16: Residual Stress: Stress remaining in a structure or member as a result of thermal or mechanical treatment. In fusion welding, stress arises because of the contraction of the metal during cooling from the solidus temperature to room temperature. 17: Peening. The mechanical working of metals by means of impact blows.
18: Pre-heating. The application of heat to the base metal prior to a welding or cutting operation.
19: Post-heating: The application of heat to a weldment after welding.
Section-I
Welding Terminology
20: Inter-pass Temperature: In a multiple-pass weld, the temperature minimum or maximum, (as specified) of the deposited weld metal before the next pass is started. 21: Puddling: If welding is done without filler rod, it is called puddling. Normally this is used for plates of less than 3 mm thickness. 22: Forehand Welding A welding technique in which the welding torch or gun is directed towards the progress of welding. The forehand welding technique adopted for thin sheets. 23: Backhand Welding A welding technique in which the welding torch or gun is directed opposite to the progress of welding. A backhand welding is used for the thickness greater than 3 mm.
Section-I
Welding Terminology
24: Weaving. A type of weld bead made with transverse oscillation, and consequently wider than the stringer bead. 25: Stringer. A type of weld bead made without appreciable transverse oscillation. 26:Duty Cycle. Duty cycle Is defined as the percentage of a 10 minute period that an equipment can be operated at a rated amperage without over heating or suffering other damage. 27: Buttering A form of surfacing in which one or more layers of weld metal are deposited on the face of a joint. The buttering provides a, metallurgically compatible transition weld deposit for subsequent completion of the weld joint. 28: KERF. The width of a cut produced during a cutting process.
Section-I
Welding Terminology
29: Brazing And Soldering Brazing and soldering are joining processes involving a filler metal with a melting temperature below the solidus temperature of the base metal. If the filler metal melts above 450 C, the process is called brazing. If the melting temperature is below 450 C, it is called soldering. Brazing Alloys -Aluminum silicon Alloy, Copper phosphorous alloy, Silver, Gold, Copper, Copper - zinc alloy, Magnesium, Nickel. Soldering Alloy - lead and tin 30: Open Circuit Voltage It is the voltage at the output terminals of a welding power source, when it is energized but has no current out put.
Section-II
Welding Safety
Introduction: Normally welding are not hazardous but a completely safe work-place is something non-existent in the world. Because welding generally requires the use of current. The hazards which are more or less peculiar to welding are; 1=Electric Shock 2=Arc Radiation 3=Fumes and dust 4=Compressed gases 5=Fire and explosions 6=Noise
Section-II
Welding Safety
1: Electric Shock: Electric shock may occur in welding if current happens to pass through the welders body; the magnitude of the current will depend upon the resistance offered by the body. A current of 0.1 A or above is taken to be lethal to humans. Human body resistance is a of 600 ohm, the lethal current will be provided by voltage of just 60V. Generally it is taken that currents up to 0.002 A do not produce pain, those between 0.002 and 0.05 A do so and are dangerous, and those higher than 0.05 A can cause heavy shocks and can be lethal at 0.01A. Therefore necessary precautions must be taken to minimize electrical risk. This can best be done by ensuring proper insulation of cables, and reliable earthing of welding equipment. The grounding circuits, sanitary sewers and water pipes, should never be used as earth or return for welding circuit.
Section-II
Welding Safety
2: Arc Radiation: An electric arc gives off visible light (wavelength 0.4 to 0.75 lam) of high intensity with a 10,000 times the safe glare level of the eyes. The intensity of emitted light depends upon the current level, and the presence of flux. Welders should always warn others nearby before striking an arc by shouting mind your eyes. Welders operating SAW units do not need shields but they should use goggles to protect their eyes from accidental flashes through the flux.
Section-II
Welding Safety
3: Fumes and Dust:
Many welding processes generate dust and particulate fumes, which when inhaled regularly over long periods may result in serious effects on the welders health. The fumes and dust generated during arc welding may be carried into the zone around the welders face by convection currents rising from the arc. Metallic vapors, mostly oxides and silicates of metals, react with atmospheric oxygen resulting in the formation of fine dust. Especially dangerous are the oxides of zinc, lead, beryllium, and copper formed during welding of copper, brass, and bronze.
Section-II
Welding Safety
4: Compressed Gases: Whether in use or stored, the cylinders should be kept vertical and secured to prevent falling by means of chains and clamps. Hammers or wrenches should not be used to open cylinder valves. Proper trolleys should be used for moving cylinders from one point to another in the workshop. A cylinder should never be carried on shoulders because in case it falls it can not only injure the person but may also explode. Compressed gas cylinders should not be exposed to sunlight or heat as this may to increase of pressure leading to explosion. The temperature of gas cylinder should never be allowed to exceed 54 0C. A cylinder valve should be opened gradually without jerk otherwise it may damage regulator diaphragm. Cylinders should be provided with their caps during storage and transport.
Section-II
Welding Safety
5: Fire and Explosions: Never keep inflammable or combustible materials in the vicinity of welding operation. Cylinders for gas welding and cutting should never be used when they are lying in horizontal position. Never use copper couplings to join hoses carrying acetylene as this could cause the formation of the potentially explosive copper acetylide. Never use oxygen for blowing out or cleaning pipes and vessels. Hot work-pieces after preheating or welding should he guarded and clearly marked in bold letters. Fire-fighting equipment must be installed in the welding workshop areas. The fire fighting equipment must be checked at regular intervals. No smoking should be allowed in the welding area where inflammable goods are being used.
Section-II
Welding Safety
6: Noise Hazard: Normal welding operations do not cause much noise but air carbon-arc gouging and plasma arc with high currents can create excessive noise requiring ear protection. Noise above 80 db is considered harmful and above 120 db outright dangerous, therefore workers exposed to such high level noise must he provided proper ear plugs.
Section-II
Welding Safety
Safety Precautions during Welding:
Section-III
Section-III
A welders cap should be worn to protect the head from hot metal and slag splatter. In addition, long hair should be tied back and tucked inside the welding jacket. Hats that are mainly polyester or have significant plastic content are not allowed.
Section-III
Section-III
Face Shield: Additional eye protection is required over safety glasses for certain tasks. For processes that will produce high velocity particles, a fullface shield is required. A face shield is required for using portable grinders, pedestal grinders, abrasive cut-off saws, and sanders. .
Section-III
Hearing Protection:
There are many noise-generating devices in the welding shop that can damage your hearing, and there are circumstances in which debris can penetrate the ear canal. Earplugs are required to protect your ears from both loud noises and foreign object damage. Ear muffles can be worn to provide even greater noise reduction.
Recommended: Silicon earplugs on a string.
Section-III
Section-III
Section-III
Body Protection:
Proper clothing can provide a great amount of protection. A welding jacket is highly recommended. Polyester fibers or nylon jackets or pants are not allowed. Pants should not have cuffs that can catch sparks or hot slag.
Section-III
highly
Section-III
Welding Helmet:
A limited number of welding helmets are provided for use. SMAW, FCAW, GMAW, GTAW and plasma cutting require a welding helmet with a welding approved shaded lens. Recommended: Use approved welding shaded lens according to the process
Section-III
Linemans Pliers
Measuring Tape
Section-III
Try Square
Wire Brush
Chipping Hammer
Section-III
Files
Hand Shear
Hand Grinder
Section-IV
Section-IV
Butt Joint
Tee Joint
Edge Joint
Corner Joint
Lap Joint
Section-IV
Lap Joint
0~5
Tee Joint
5(Excl.) ~ 90
Edge Joint
0 ~ 30
Corner Joint
30(Excl.) ~ 135
Butt Joint
135(Excl.) ~ 180
Section-IV
Section-IV
Section-IV
Section-IV
Section-V
Section-V
SMAW is the most widely used of the various arc welding processes.
SMAW uses an arc between a covered electrode and the weld pool. It employs the heat of the arc, coming from the tip of a consumable covered electrode, to melt the base metal. Shielding is provided from the decomposition of the electrode covering. Either alternating current (ac) or direct current (dc) may be employed, depending on the welding power supply. A constant-current (CC) power supply is preferred. SMAW is a manual welding process.
Section-V
Section-V
Section-V
Section-V
GTAW is an arc welding process that uses an arc between a nonconsumable tungsten electrode and the weld pool.
The process is used with shielding gas and without the application of pressure. GTAW can be used with or without the addition of filler metal. The CC type power supply can be used with either dc or ac, the choice depends largely on the metal to be welded. Direct current welding is typically performed with the electrode negative (DCEN) polarity. Alternating current is mainly used for welding of Aluminium and Magnesium.
Section-V
Section-V
Section-V
Section-V
GMAW is an arc welding process that uses an arc between continuous filler metal electrode and the weld pool.
The process is used with shielding from an externally supplied gas and without the application of pressure. GMAW may be operated in semiautomatic, machine, or automatic modes. It uses either the short circuiting, globular, or spray methods to transfer metal from the electrode to the work.
Section-V
Section-V
Section-V
Section-V
Section-V
Section-V
Section-V
Section-V
Section-V
Section-V
Section-V
Section-V
Section-V
Section-V
a. A power supply capable of providing high amperage at 100% duty cycle is recommended.
b. Weld is not visible during the welding process. c. Equipment required is more costly and extensive, and less portable.
Section-VI
Welding Consumables
Introduction:
Welding consumables are materials used up during welding such as electrodes, filler rods, fluxes and externally applied shielding gases.
Welding consumables can be grouped in to; 1: Coated electrode 2: Fluxes 3: Filler wires/ filler rods 4: Shielding gases
Section-VI
Welding Consumables
Selection of Electrodes: Base Metal Strength Properties Base Metal Composition Welding Position Joint Design and Fit-up Thickness and Shape of Base Metal Production Efficiency and Job Conditions
Section-VI
Welding Consumables
Fluxes: Flux is a material used during welding, brazing or braze welding to clean the surfaces, the joint chemically, to prevent atmospheric oxidation and reduce impurities or float them to the surface. Fluxes are used in 1: SMAW 2: SAW 3: FCAW
Welding Consumables
AWS Filler Metal Specification:
Section-VI
More Electrodes standards: AWS: American Standards DIN: German Standards JIS: Japanese Standards
Section-VI
Welding Consumables
Section-VI
Welding Consumables
Section-VI
Welding Consumables
Section-VI
Welding Consumables
Section-VII
Welding Imperfections
Introduction: This section is concerned mainly with discontinuities, which may or may not be classified as defects (rejectable) depending on requirements of individual specifications or codes. Discontinuity: A discontinuity is defined as an interruption of the typical structure of a weldment, such as a lack of homogeneity in the mechanical, metallurgical, or physical characteristic of the material, or weldment. A discontinuity is not necessarily a defect. Discontinuities are rejectable only if they exceed specification requirements in terms of type, size, distribution, or location. A rejectable discontinuity is referred to as defect.
Defect:
By definition, a defect is a discontinuity whose size, shape or location makes detrimental to the useful service of the part in which it occurs. Discontinuities may be found in the weld metal, heat affected zone, or base metal of many elements.
Section-VII
Welding Imperfections
Welding Discontinuities/Defects: Discontinuities/defects can be divided into following categories. 1) 2) 3) 4) 5) 6) 7) 8) Cracks Gas Pores & Porosity Solid Inclusions Lack of fusion Incomplete Joint Penetration Dimensional Discontinuities Mechanical or Surface damage Misalignment
Section-VII
Welding Imperfections
1: Cracks Cracks form in the weld and base metal when localized stresses exceed the ultimate strength of the material. Cracking may occur at elevated temperatures during weld metal solidification or after solidification when the weldment has equalize in temperatures. Cracks can be classified as either hot cracks or cold cracks. Hot cracks develop at elevated temperatures. Cold cracks develop after solidification is complete. Hot cracks propagate along grain boundaries. Cold cracks propagate both along grain boundaries and through grains.
Section-VII
Section-VII
Welding Imperfections
Causes of Cracks; 1. Highly rigid joint 2. Excessive dilution 3. Defective electrodes 4. Poor fit-up 5. High sulfur base metal
6. Crater cracking
Section-VII
Welding Imperfections
2: Porosity: Porosity is characterized by cavity type discontinuities formed by gas entrapment during solidification.
Surface breaking porosity Coarse cluster porosity Fine cluster porosity Blow hole > 1.6 mm
Section-VII
Welding Imperfections
Causes of Porosity:
Section-VII
Welding Imperfections
3: Solid Inclusion: Entrapment of solid particles results into solid inclusion
Surface breaking solid inclusion Internal solid inclusion causing a lack of inter-run fusion Internal solid inclusion causing a lack of sidewall fusion
Section-VII
Welding Imperfections
Causes of Solid Inclusion:
Section-VII
Welding Imperfections
4: Incomplete Fusion: Incomplete fusion is termed as fusion which does not occur over the entire intended for welding and between all adjoining weld beads.
Section-VII
Welding Imperfections
Causes of Incomplete Fusion:
Section-VII
Welding Imperfections
5: Incomplete Joint Penetration: Incomplete joint penetration is defined as penetration by weld metal that does not extend for the full thickness of the base metal in a joint with a groove weld.
Section-VII
Welding Imperfections
Section-VII
Welding Imperfections
6: Dimensional Discontinuities: Production of satisfactory weldment requires staying within specified sizes and shapes of welds and finished dimensions of an assembly. Dimensional data with tolerances may be found on drawings and in specifications and codes. Assemblies not meeting the requirements must be corrected before final acceptance. a) Distortion b) Incorrect Joint Preparation c) Incorrect Weld size and profile a) Incorrect Final dimensions
Section-VII
Welding Imperfections
6 (a): Distortion A change, permanent or temporary, in shape or dimensions of a part as a result of heating and welding. It may be; I. Longitudinal II. Transverse III. Angular IV. Bowing
Section-VII
Welding Imperfections
Causes of Distortion
I. The Heat Input II. Restraint III. Inherent Stresses in the Parent Metal IV. Parent Metal Properties
Section-VII
Welding Imperfections
Prevention of Distortion Rule-1 (Reduce the effective shrinking force) Rule-2 (Making shrinkage works to reduce distortion)
Section-VII
Welding Imperfections
Prevention of Distortion Rule-1 (Reduce the effective shrinking force) Do not Over weld Use Proper weld fit up Use few passes Use intermittent welds The use back step technique
Section-VII
Welding Imperfections
Prevention of Distortion Rule-2 (Making shrinkage works to reduce distortion) Locating part out of position
Section-VII
Welding Imperfections
Prevention of Distortion
Section-VII
Welding Imperfections
6 (b): In correct Joint Preparation
Established welding practice requires proper joint dimensions for each type of joint, consistent with the thickness of the material being welded.
Failure to meet these criteria may result in a greatly increased tendency to produce discontinuities in the weld, in addition to the possibility of creating distortion. Therefore, it is important that joint preparation is the same as shown in the applicable drawings and within specified limits of the specification.
Section-VII
Welding Imperfections
6 (c): In correct weld size and profile:
Section-VII
Welding Imperfections
6 (d): In correct final Dimensions: Weldments are fabricated to meet certain dimensions, whether specified on detailed drawings or hand-written sketches. The fabricator must be aware of the amount of shrinkage to be expected at each weld joint. This will affect the final overall dimensions of the product. Weldments that require rigid control of final dimensions usually must be by machining or grinding after welding or after post weld heat treatment to stay within limits.
Section-VII
Welding Imperfections
7: Mechanical or Surface Damage: Mechanical or surface damage may be caused by; Grinding
Section-VII
Welding Imperfections
8: Misalignment: Linear Excess weld metal height Lowest plate to highest point
3 mm
15
Section-VIII
It is the duty of all welding inspectors to ensure that welding operations are carried out in accordance with written, or agreed practices or specifications
Section-VIII
2) 3) 4) 5)
Section-VIII
1) 2) 3) 4) 5) 6) 7)
Pre-Heating. In process distortion control Consumable control Welding process Welding run sequence and inter-pass cleaning Minimum/maximum Inter-pass temperatures Full compliance with all elements given on the WPS.
Section-VIII
4)
5) 6) 7)
Section-IX
Section-IX
Section-IX
Mirrors Valuable to the inspector allowing them to look inside piping, threaded and bored holes, inside castings and around corners if necessary.
Magnifiers Helpful in bringing out small details and defects. Fiberscopes & Boroscopes: Widely used for examining tubes, a deep hole, long bores, and pipe bends, having internal surfaces not accessible to direct viewing.
Section-IX
Mirror
Magnifier
Fiberscope
Boroscope
Section-IX
Steel Rule:
Available in a wide selection of sizes and graduations to suit the needs of the inspector.
Section-IX
Section-IX
Combination square set: Consisting of a blade and a set of three heads: Square, Center and Protractor. Used universally in mechanical work for assembly and layout examination.
Section-IX
Thickness gauge: Commonly called a Feeler gauge is used to measure the clearance between objects.
Section-IX
Section-IX
Section-IX
Section-IX
Section-IX
Section-IX
Section-IX
Section-IX
Section-IX
Section-IX
Section-IX
i: Pressure testing: Pressure (Hydrostatic) Testing is carried out after all work has been completed and all examinations have been performed.
A suggested test procedure could be as follows; Ensure adequate venting of the vessel during filling to prevent air pockets and during draining to prevent the formation of a vacuum.
Section-IX
Section-IX