Академический Документы
Профессиональный Документы
Культура Документы
A.2 The Courses governed by AICTE shall be of four academic years duration or 8 semesters and the
course governed by Council of Architecture shall be of five academic year’s duration or 10 semesters.
The duration of each semester is 16 weeks.
The scheme of study and examination for 1 Year (I & II Semesters) will be the same for all the
branches of Engineering under AICTE, except for Architecture branch.
A.3 The Calendar of events in respect of the course shall be as fixed by the University from time to time.
A.4 Examination in all the subjects of all the eight semesters of B.E. and 10 semesters of B.Arch will be
conducted after the end of each semester, except when there are no candidates appearing for any subjects.
B. ADMISSIONS
B.1. a) Admission to the First Year Course through Common Entrance Test / Aptitude test conducted by
appropriate bodies of Government of Karnataka shall be open to student who have passed
(i) The Two Years Pre-University Examination conducted by the Karnataka State Pre-University Board
and
(ii) Plus Two C.B.S.E. or I.C.S.E. with Physics, Chemistry and Mathematics as optional papers and
English as a paper of study or any other examination recognized by the University as equivalent thereto.
b) Candidates belonging to all categories shall have secured a minimum of 35% percent marks in the
aggregate of the three optional papers i.e. Physics, Chemistry, and Mathematics of Second Year of the
qualifying Examination or at the Public Examination held at the end XII Year to be considered eligible for
admission to first year B.E or B.Arch. by the University.
B.2 a) B.Sc., Graduates are also considered for admission to First Semester through Common Entrance
Test / Aptitude test conducted by appropriate bodies of Government of Karnataka if they have secured a
minimum of 50% marks in the aggregate of (i) Physics, Chemistry and Mathematics, (ii) Physics,
Mathematics and Electronics (iii) Physics, Mathematics and Computer Science at the B. Sc. Examination.
However, in case of Schedule Caste and Schedule Tribes or any other group classified by Government of
Karnataka for such purposes the percentage of the aggregate - marks in the specified group of subjects
shall not be less than 40%
B.3 Diploma holders in appropriate Branch of Engineering granted by the Board of Technical Examination
in Karnataka or equivalent who have obtained not less than 50% of the total maximum marks in the final
examination leading to the said Diploma, are considered for admission to III Semester of Day and Evening
courses of appropriate branches of Engineering. In case of candidates belonging to Schedule Castes,
Schedule Tribes and Backward Tribes or any other group classified by the Government of Karnataka, the
percentage of marks obtained should not be less than 40%.
Note : Students admitted on the basis of B.2 and B.3 are not eligible for exemption in any of the subjects
of B.E. Degree Course or B.Arch.
2K6 SYLLABUS
2
B.4 a)
I) All the candidates irrespective of quota / category to which they belong to and admitted to UVCE at
I Semester and III Semester of any branches or transferred to UVCE from any other University shall pass
the following Audit subjects.
i) Kannada ii) Environmental Studies
iii) Communication Skills and Technical Report Writing and iv) Indian Constitution
II) All the candidates irrespective of quota / category to which they belong to and admitted to UVCE at
I Semester and III Semester of B.Arch or Transferred to UVCE from any other University shall pass the
audit subject Kannada.
• Each Audit subject shall be assessed for an Internal assessment marks of 50.
The Internal assessment marks shall be based on 2 tests. The tests will have to be answered in “Blue
Books”.
Provision is made for an additional test to be conducted at the end of the Semester to provide an
opportunity to the student to improve the internal assessment marks, with the permission of the
Departmental Chairman.
The average of the marks obtained for any two tests and converted to 50 marks should be chosen for the
award of internal assessment marks to the advantage of a student.
If a candidate is absent to all the tests conducted, the internal assessment marks awarded will be zero.
All audit subjects are considered as “Sessional subject” for which a student has to obtain a minimum of 20
out of 50 marks.
If a student fails to satisfy the sessional requirement of the audit subject, he / she can make it up during
the next academic semester, with the consent of the Staff teaching the Audit subject and Chairman, to
which the concerned candidate belongs to.
• A student shall attend a minimum of 75% of the total number of classes held in each of the audit
subject. In case the candidate fails to attend 75% of the class held in audit subject, he / she will attend the
same during the next academic year along with regular students.
Separate consolidated marks card inrespect of audit subjects shall be issued to the candidate, qualified for
the degree of Engineering or B.Arch along with VIII Semester marks card in case of Engineering courses
and X Semester marks card in case of Architecture course.
b) All the candidates admitted to III Semester of Engineering courses under Diploma quota have to
complete the Bridge course subjects Mathematics I & Mathematics II before getting admitted to VII
Semester. Those candidates admitted to III Semester Day and Part Time B.E Mechanical Engineering
course have to complete one more Bridge course subject “Basic Electronics & C Programming”.
Along with this condition the candidates have to satisfy regulation under H-Promotions and Eligibility
for Examination.
C. REGISTRATION TO COURSE./EXAMINATION
C.1 Every candidate should register for each semester before the reopening of the Semester by paying the
prescribed tution and other fees without fine and within the next two weeks by paying the prescribed fine.
D. ATTENDANCE
D.1 A candidate shall undergo the prescribed course of study in the University Visvesvaraya College of
Engineering, Bangalore University.
D.2 A student shall attend a minimum of 75% of the total number of classes held in each of the subject
(Theory, Drawing and Practical) in each Semester.
2K6 SYLLABUS
3
D.3 A candidate not obtaining 75% of the attendance as stated in D.2 shall not be permitted to take the
concerned semester examination.
D.4 Candidate having less than 75% attendance in any subject have to repeat that particular semester along
with the regular students of that semester during next academic year.
D.5 The basis for the calculation of attendance shall be the period prescribed by the University by its
calendar.
E .INTERNAL ASSESSMENT
E.1 whether theory or practical each paper shall have an internal assessment (IA) Marks as mentioned in
the Scheme of study.
E.2 a) The I.A. marks in a theory paper shall be based on two tests, normally conducted during the 8th and
12th week of each semester as per the calendar of events fixed by the University. The tests will have to be
answered in 'Blue Books' with Pages serially numbered.
b) Provision is made for an additional test to be conducted at the end of the semester to provide an
opportunity to the student to improve the Sessional marks, with the permission of the Departmental
Chairman / Chairperson.
c) The average of the marks obtained from any two tests shall be chosen for the award of Sessional marks,
to the advantage of a student.
d) If a candidate is absent in all the tests, the Internal Assessment Marks will be awarded as zero in that
paper.
E.3. In the case of practicals and drawings, 60% of the Internal assessment marks shall be assessed by the
work done in the respective classes and Laboratory Record/ Drawing / Workshop models and Diary
submitted thereon and 40% of the Internal Assessment marks by a test.
In respect of Architecture Course 80% of the Internal assessment Marks shall be assessed by the work
done in the class and 20% by a test.
E.4. Internal Assessment marks in case of Project Work, extensive Survey project and Educational Tours
are to be awarded by the concerned teachers/guides and are also considered as Sessional subject for which
a student has to obtain a minimum of the Internal Assessment marks as mentioned
E.5. The Internal Assessment marks awarded shall be displayed on the notice board of the respective
Department latest by two weeks after the end of the semester and, certified copy with any corrections
incorporated shall be forwarded to the University authorities as specified. The students are advised to
maintain the blue books till one month from the date of announcement of results by the University.
E.6 ELIGIBILITY
a) There is no separate minimum requirement of I.A marks in each theory subject to be eligible to appear
for the semester examination of Engineering courses.
The minimum Class marks required in each subject is 50% of the Internal Assessment marks to appear
for the examination of the Concerned Semester of Architecture Branch.
b) However, the minimum Sessional requirement specified in each of the Practicals, Drawing, project
work, extensive survey projects and project tours is 50% of the Internal Assessment marks as mentioned in
the Scheme (12 out of 25 marks) to be eligible to appear for the examination of the concerned semester.
c) Those students who fail to get the minimum Sessional I.A marks in anyone of the paper as per E.6 (b) is
declared to have Not Satisfied the Session Requirements (NSSR) and is not permitted to go to the next
Semester and also not permitted to appear for that Terminal Examination.
To continue the course, they have to repeat the entire course work of that semester along with the
regular students during the next academic year.
2K6 SYLLABUS
4
F. MINIMUM FOR PASS, DECLARATION, AND CLASSIFICATION OF RESULTS
F.1. a) For a pass in semester a candidate shall secure a minimum of 35% of the marks prescribed for each
paper in the University Examination (Theory, Practical, Drawing, Project work, Viva Voce etc.) and 40%
marks in the total aggregate of all papers and their internal Sessional marks prescribed for that semester in
the first appearance.
b) For a Pass in each subject a candidate of Architecture course shall secure a minimum of 35% of the
marks prescribed for a subject in the University Examination (Theory, Practical, Drawing, Project work,
Viva-Voce etc) and 40% in overall aggregate of marks of all subjects put together (including Class marks
or Internal assessment, Viva-Voce, Practical and Theory exam)
F.2. Those students who pass in all the papers as stated in F.1 but fail to get the aggregate percentage of
marks are declared to have failed in the examination. However, they may be permitted to withdraw only
theory subjects to make up the deficiency in aggregate.
F.3. The candidates who do not satisfy F.1 shall be deemed to have failed and have to appear in the failed
papers at the University Examination on the next occasion. There will however, be no change in the
internal marks allotted to the candidate, except when the student repeats the semester as provided in E.6
(b) or F.4.
F.4. Provision is made for one and only one rejection of results of all the papers in each semester if the
candidate decides to reappear for all papers of that - semester. Such rejection should be made within 30
days of announcement of result, by making a written application through the Principal of the College, to
the Registrar (Evaluation).
If such rejection is in respect of the results of all the papers of one semester, he will have the option to
repeat his studies for that semester and earn fresh internal Assessment marks as well and gets the benefit of
first appearance. The earlier rejection of the results
however cannot be revoked.
F.5. The results of any semester will be declared as passed or failed as the case may be in accordance with
Regulation F.1
F.6. To be eligible for the award of the B.E. Degree in any branch or B.Arch, a candidate shall have
completed the scheme of training and passed in all papers prescribed for the course.
F.7. Further to regulation F5, the following classification will be made in the declaration of results (i) of
each semester and (ii) the final declaration of successful candidates for the degree course.
(1) First Class with Distinction
(2) First Class and
(3) Second Class
F.8. a) For the declaration of class of each semester, the marks obtained by the candidate in the first
appearance for that semester will be taken into account except as per clause F.4
b) Those students who pass all the papers of a semester in the First appearance as per the Regulation F.1
and also secure not less than 70% of the aggregate marks will be declared to have passed that examination
in 'First Class with distinction'.
c) Those students who pass all the papers of a semester in First appearance as per Regulations F.1 and also
secure 60% and above but less than 70% of the aggregate marks will be declared to have passed that
examination in First Class. Also those students who fail in one or more subjects but passes in those
subject(s) subsequently and secure 60% and above but less than 70% of the aggregate marks at the first
appearance will be declared to have passed in First Class.
d) All the remaining successful candidates who pass all the papers of semester as per Regulation. F.1 will
be declared to have passed in Second class.
2K6 SYLLABUS
5
F.9. For the final declaration of successful candidates for the entire course, marks obtained by a candidate
in the first appearance taking all the papers of VII and VIII semester Examinations will be considered for
declaration of class as follows.
a) Candidates who secure 70% and above marks in the aggregate of VII and VIII Semesters, and also pass
in all the papers of VII & VIII semester in First appearance subject to regulation F. 7. Will be declared to
have passed the BE Degree Examination in First Class with Distinction and will be indicated in the degree
certificate.
b) Candidates who secure 60% and above but less than 70% marks in the aggregate of VII and VIII
Semesters in First appearance subject to Regulation F.7 will be declared to have passed the B.E. Degree
Examination in First Class and will be indicated in the degree certificate. (As in F.8. c above)
c) All other successful candidates satisfying Regulation F.1 and F.6 will be declared to have passed B.E.
Degree Examination in Second Class.
d) Candidates who secure 70% and above marks in the aggregate of VII to X Semesters, and also pass in
all the papers of VII to X semesters in First appearance subject to regulation F. 7. Will be declared to have
passed the B.Arch Degree Examination in First Class with Distinction and will be indicated in the degree
certificate.
e) Candidates who secure 60% and above but less than 70% marks in the aggregate of VII to X Semesters
in First appearance subject to Regulation F.7 will be declared to have passed the B.Arch. Degree
Examination in First Class and will be indicated in the degree certificate. (As in F.8. c above)
G. BENEFITS OF EXEMPTION
In case a candidate who pass all the subjects by scoring 35% in each subject but fails to get 40% in
aggregate is permitted to withdraw only few theory subjects to make up 40% of marks in aggregate.
H.1 An academic year consists of Odd and Even Semester. A candidate is eligible for promotion
to next academic year (starting with an Odd Semester) provided the candidate has not failed in more than 4
papers of the two semesters of the just previous academic year and has completed all papers of the
examinations lower to the previous year. Not withstanding E6(c), there is total mobility from the Odd to
the Even Semesters of any particular academic year. As an example, a candidate seeking eligibility to
VII Semester should have passed all the papers up to and including IV Semester and should 'not have
failed in more than 4 papers of V and VI Semester put together.
H.2. Candidates not covered by Regulation H.1 are not eligible for promotion to the next Semester till they
qualify under regulation H.1
H.3. A candidate, who does not obtain eligibility to enter III Semester with in a period of three consecutive
academic years from the date of admission, has to discontinue the course.
However the candidate may get re-admitted to the I Semester of BE. Degree course of the University to
continue the course.
2K6 SYLLABUS
6
I. TRANSFER OF STUDENTS
1. Subject to the conditions like intake and approval by the University, Change of branch is allowed to III
Semester only provided the candidate seeking the Change of branch has passed in all the papers of the I &
II Semester of Engineering courses of UVCE.
2. Transfer of students from any other Universities of Karnataka State to Bangalore University will be
permitted to the same branch only at the beginning of III Semester or V Semester and not beyond,
provided he/she has passed in all the papers of the earlier semesters.
In addition he/she should get academic clearance from Dean Faculty of Engineering, Bangalore
University, Bangalore who may suggest any additional papers to be studied by the candidate if necessary.
3. A candidate seeking transfer from another University under Regulation I.1 should have cleared all the
subjects of the previous years/semesters prescribed by parent University and produce a certificate to that
effect from the University Registrar before seeking transfer.
2K6 SYLLABUS
7
Proceedings Extract of the meeting of the faculty of Engineering held on 23-05-2006 at 11.30 AM in
the Seminar Hall, UVCE, KR Circle, Bangalore
Resolutions:
A. To stagger the subjects a) Physics – Theory & Practical b) Chemistry – Theory & Practical c)
Mechanical Engineering Science & d) Workshop Practice, as shown below,
2K6 SYLLABUS
8
BANGALORE UNIVERSITY
2K6 SCHEME
(EFFECTIVE FROM AUGUST 2006)
I SEMESTER
II SEMESTER
2K6 SYLLABUS
9
III SEMESTER
Sl Code No. Subject Teaching No. of Hr/week Duration of Class / Exam Total
No Department Theory Pract Exam Sessional Marks Marks
Theory Pract Marks
1. 2K6SM301 Engineering Mathematics 4 - 3 - 25 100 125
Mathematics – III
2. 2K6EE301 Analog Electronic EE 4 - 3 - 25 100 125
Circuits-I
3. 2K6EE302 Electric Circuits EE 4 - 3 - 25 100 125
4. 2K6EE303 Electrical EE 4 - 3 - 25 100 125
Machines I (DC
Machines &
Transformers)
5. 2K6EE304 Electrical & EE 4 - 3 - 25 100 125
Electronics
Measurements
6. 2K6EE305 Electronics EE - 3 - 3 25 100 125
laboratory I
7. 2K6EE306 Electrical EE - 3 - 3 25 100 125
Machines
laboratory I
8. 2K6EE307 Electrical Circuits EE - 3 - 3 25 100 125
& Measurements
laboratory
TOTAL 200 800 1000
IV SEMESTER
Sl Code No. Subject Teaching No. of Hr/week Duration of Class / Exam Total
No. Department Theory Pract Exam Sessional Marks Marks
Theory Pract Marks
1. 2K6SM401 Engineering Mathematics 4 - 3 - 25 100 125
Mathematics – IV
2. 2K6EE401 Analog Electronic EE 4 - 3 - 25 100 125
Circuits-II
3. 2K6EE402 Micro Electronics EE 4 - 3 - 25 100 125
4. 2K6EE403 Signals and EE 4 - 3 - 25 100 125
Systems
5. 2K6EE404 * Object Oriented EE 4 - 3 - 25 100 125
Programming
Using C++
6. 2K6EE405 Electrical Machines EE 4 - 3 - 25 100 125
II (Induction
Machines &
Synchronous
machines)
7. 2K6EE406 Electrical Machines EE - 3 - 3 25 100 125
Laboratory II
(Induction &
Synchronous)
8. 2K6EE407 Electronics EE - 3 - 3 25 100 125
laboratory II
TOTAL 200 800 1000
* NOTE: LAB PRACTICE-OBJECT ORIENTED PROGRAMMING USING C++ MARKS 15 OUT OF 25
2K6 SYLLABUS
10
V SEMESTER
Sl Code No. Subject Teaching No. of Hr/week Duration of Class / Exam Total
No. Dept Theory Pract Exam Sessional Marks Marks
Theory Pract Marks
1. 2K6EE501 Control Systems EE 4 - 3 - 25 100 125
Engineering
2. 2K6EE502 Electrical EE 4 - 3 - 25 100 125
Machine Design
3. 2K6EE503 Transmission & EE 4 - 3 -- 25 100 125
Distribution
4. 2K6EE504 Power EE 4 - 3 - 25 100 125
Electronics
5. 2K6EE505 E M F Theory EE 4 - 3 - 25 100 125
6. 2K6EE506 Electrical EE 4 - 4 - 25 100 125
Drawing
7. 2K6EE507 Power EE - 3 - 3 25 100 125
Electronics
laboratory
8. 2K6EE508 Circuits and EE - 3 - 3 25 100 125
Control
Simulation lab
TOTAL 200 800 1000
VI SEMESTER
Sl Code No. Subject Teaching No. of Hr/week Duration of Class / Exam Total
No. Dept Theory Pract Exam Sessional Marks Marks
Theory Pract Marks
1. 2K6EE601 Micro Processor & EE 4 - 3 - 25 100 125
Micro Controller
2. 2K6EE602 H V Engineering EE 4 - 3 - 25 100 125
3. 2K6EE603 Advanced Control EE 4 - 3 - 25 100 125
Systems
4. 2K6EE604 Communication EE 4 - 3 - 25 100 125
Systems
5. 2K6EE605 AC / DC Drives EE 4 - 3 - 25 100 125
6. 2K6EE606 Computer -- 4 - 3 - 25 100 125
Organization &
Design
7. 2K6EE607 Industrial Drives EE - 3 - 3 25 100 125
laboratory
8. 2K6EE608 Micro Processor & EE - 3 - 3 25 100 125
Micro Controller
laboratory
TOTAL 200 800 1000
2K6 SYLLABUS
11
VII SEMESTER
Sl Code No. Subject Teaching No. of Hr/week Duration of Class / Exam Total
No. Dept Theory Pract Exam Sessional Marks Marks
Theory Pract Marks
1. 2K6EE701 Power System I EE 4 - 3 - 25 100 125
2. 2K6EE702 Non EE 4 - 3 - 25 100 125
Conventional
Energy Sources
3. 2K6EE703 Switch Gear & EE 4 - 3 - 25 100 125
Protection
4. 2K6EE704 Digital Signal EE 4 - 3 - 25 100 125
Processing
5. Elective I -- 4 - - - 25 100 125
6. 2K6EE706 Power Systems EE - 3 - 3 25 100 125
laboratory I
7. 2K6EE707 DSP laboratory EE - 3 - 3 25 100 125
8. 2K6EE708 Estimation, EE 4 - 3 - 25 100 125
Economics &
Management
TOTAL 200 800 1000
Elective I
2K6EE705.1 Illumination Engineering 2K6EE705.2 Embedded System Design
2K6EE705.3 Operating Systems 2K6EE705.4 Web Technologies
2K6EE705.5 Digital Control Systems 2K6EE705.6 Linear Induction Motors
2K6EE705.7 Advanced Electrical Machinery 2K6EE705.8 Programmable Logic Controllers
VIII SEMESTER
Sl Code No. Subject Teaching No. of Hr/week Duration of Class / Exam Total
No. Dept Theory Pract Exam Sessional Marks Marks
Theory Pract Marks
1. 2K6EE801 Power Electronics EE 4 - 3 - 25 100 125
in Industry
2. 2K6EE802 Power System II EE 4 - 3 - 25 100 125
3. 2K6EE803 HVDC & FACTS EE 4 - 3 - 25 100 125
4. 2K6EE804 Utilization of EE 4 - 3 - 25 100 125
Electric Power
5. Elective II EE 4 - 3 - 25 100 125
6. 2K6EE806 Project Tour & EE Project Tour involving visit to 50 -- 50
Industrial visit Industries, Substations/Receiving
stations, Hyde plant, Thermal plant
and Nuclear plants within the state is
for a duration not exceeding 5 days
7. 2K6EE807 Power Systems EE - 3 - 3 50 100 150
laboratory II
8. 2K6EE808 Project laboratory EE - 3 - 3 50 100 150
9. 2K6EE809 Seminar EE 3 hrs/week 25 - 25
TOTAL 300 700 1000
Elective II
2K6EE805.1 Artificial Intelligence & Expert Systems 2K6EE805.2 Neural Network & Fuzzy Logic
2K6EE805.3 Resonant Converters 2K6EE805.4 Computer Graphics
2K6EE805.5 Power System Operation & Controls 2K6EE805.6 Transducers & Signal Conditioning
2K6EE805.7 Energy Management & Auditing 2K6EE805.8 Power Supply System Design
2K6EE805.9 Micro Electronics & Mechanical System 2K6EE805.10 Data Communication
2K6 SYLLABUS
12
2K6 SYLLABUS
I Semester B.E
6SM1101 ENGINEERING MATHEMATICS –I
(Common to Civil, Mechanical, Electrical, Electronics, Computer Science & Information Science)
PART - A
Differential Calculus
PART - B
Unit-V: Differential Equations:
Solutions of ordinary differential equations of first order and first degree: Homogeneous forms, Linear
and Bernoulli equations, Exact and reducible to exact equations, using standard integrating factors-
Orthogonal trajectories in Cartesian and polar forms. 8hrs
Unit-VI: Infinite series:
Convergence, Divergence and Oscillation of an infinite series, De Alembert’s ratio test, Cauchy’s root
test, Raabe’s test (without proof) for series of positive terms, Alternating series, Absolute and
conditional convergence, Leibnitz’s test (without proof) Summation of Binomial, Exponential and
logarithmic series. 7hrs
Unit-VII: Analytical Geometry in three dimensions:
Cartesian co-ordinates in 3 dimensions- distance and division formulae- direction ratios and direction
cosines- angle between direction cosines- angle between two lines. 7hrs
Unit-VII: Equation of plane in different forms, Perpendicular distance of a point from a plane- angle
between two planes , line of intersection of two planes, planes co-axial with given plane, equation of lines
in different forms, perpendicular from a point onto a line, angle between a line and a plane, co-planarity of
two lines, shortest distance between lines. 8hrs
Text Books:
1. B. S. Grewal, “Higher Engineering Mathematics” 36th Edition, 2001, Khanna Publishers, Delhi.
2. E. Kreyszig, “Advanced Engineering Mathematics” 8th Edition, 2004, John Wiley and sons.
Note:
Question paper shell contain 8 questions, one question from each unit.
Five questions to be answered choosing atleast 2 from each part.
2K6 SYLLABUS
13
2K6 SYLLABUS
I Semester B.E
6CE1101 ENGINEERING MECHANICS
(Common to all branches except B.Arch)
PART B
5. Friction: Introduction, laws of dry friction, limiting friction, co-efficient of friction, angle of
friction, angle of repose. Equilibrium of a block on (horizontal, inclined plane), Equilibrium of
block & wedge and equilibrium of ladder. 8 Hrs
6. Basic principles of dynamics: Kinematics and kinetics. Kinematics of rectilinear motion with
uniform and variable acceleration. Kinematics of curvilinear motion, in vertical plane, equation to
the path of projectile. 8 Hrs
7. Kinetics of rectilinear motion, Dynamic equilibrium, equations of equilibrium, kinetics of
curvilinear motion, centrifugal force, banking and super elevation. 8 Hrs
8. Work and Energy: Kinetic and potential energy, principles of work and energy, work done by
force on spring. Work done by a force, couple. Principle of Virtual Work 4 Hrs
References:
1. Hibbeler, R.C., Engineering Mechanics, Statics & Dynamics, Prentice Hall, New Jersey, Ninth
Edition, 2001.
2. Beer & Johnston, Mechanics for Engineers, Statics & Dynamics, and McGraw Hill Book Company,
New York, Third edition, 1998.
3. Merriam, J.L., Engineering Mechanics, Statics and Dynamics, John Wiley & Sons, New York, 1980.
4. Jindal, U.C., Engineering Mechanics, Statics – I, Galgotia Publication Pvt. Ltd., New Delhi, Second
edition, 2003.
5. Jindal, U.C., Engineering Mechanics, Dynamics – II, Galgotia Publication Pvt. Ltd., New Delhi,
Second Edition, 2004.
2K6 SYLLABUS
14
2K6 SYLLABUS
I Semester B.E
6EE 1.01 ELECTRICAL SCIENCES
(Common to all branches except B.Arch)
PART A
PART B
Reference Books :
1. Electrical Technology - H. Cotton
2. Electrical Engineering - Hughes
3. Electrical Technology - B. L. Theraja
4. Electrical Sciences - M. V. Rao
5. Electrical Sciences - Yoganarasimhan
6. Electrical Engineering - V. K. Mehta
7. Basic Electrical Sciences - Prof. P. M. Chandrashekaraiah
2K6 SYLLABUS
15
2K6 SYLLABUS
1. Physics of Vibrations: SHM and its expression and differential equation-Superposition of two
linear SHMs-Lissagious figures. Damped Vibrations-Differential equations and its solutions
critical damping, logarithmic decrement-analogy with electrical circuits. Forced vibration-
differential equations-Amplitude, Velocity resonance, sharpness of resonance and quality factor.
5 hrs
2. Elasticity : Hooke’s law-definition and its limits, Elastic constants (definitions only) and
Poisson’s ratio and its limitation-Derivation of relation between q, n, k, -torsion of Cylinder –
theory – expression for couple per unit twist and n-bending of beams-expression for bending
moment-single cantilever. 5 hrs
3. Cryogenics : Idea of throttle expansion of gases, Joule Thomson experiment, Expression for
inversion temperature, Methods of production of low temperature, Linde’s air liquefier, adiabatic
and nuclear demagnetization. Measurements of low temperature by different methods, platinum
resistance thermometer-theory and construction.
4 hrs
1. Free electron theory of metals : Classical theory-Expression for drift velocity and electrical
conductivity – Weidman Franz law – Specific heat.
Review of Band theory of solids – forbidden band-allowed bands – classification of metals,
semiconductors and insulators – examples. 5 hrs
PART B
Modern Optics
1. Lasers : Spontaneous and stimulated emission of radiation – population inversion – optical resonator –
necessary condition for laser action – construction and working of Ruby-Helium-Neon and semi
conducting laser-applications of laser-laser welding, cutting, drilling and defense. 4 hrs
2. Fiber optics : Core and cladding-total internal reflection-Derivation of expression for numerical
aperture and acceptance angle-types of optical fibers-attenuation-absorption-scattering-applications in
communication-point to point (block diagram level only). 4 hrs
2K6 SYLLABUS
16
Engineering Materials
3. Liquid Crystal : Classification – Orientational order intramolecular forces – deformation of the director
magnetic effects – optical properties – applications – LCD. 5 hrs
Reference Books :
1. Modern Physics, Kenneth. S. Krane, John Wiely & Sons.
2. Solid State Physics, S. O. Pillai, New Age International
3. Elementary Solid State Physics, Ali-Omar, John Wiely & Sons
4. Material Science, S. L. Kulkarni & K. C. Bhandari, New Age International
5. Physics for Scientists & Engineers, Serway & Jewett, Thomson Book Collection
6. Lasers-Principles, Types & Application, K. R. Nambiar, New Age International
7. A Text Book of Engineering Physics, M.N. Avadhanulu & P. G. Kshirsagar,
S. Chand & Company
8. Nanosystems-Molecular Machenary Manufacturing & Computation, K. Eric Drexler, John Wiely
and Sons
9. Fundamentals & Applications of Ultrasonic waves, J. David N Dheeke & Cheek & Cheek, CRC
Press
10. Laboratory manual in Applied Physics, H. Satyaseelan, New Age International
2K6 SYLLABUS
17
2K6 SYLLABUS
3. GREEN CHEMISTRY
Introduction, Principles, Atom economy : Concept, AE in oxidation of benzene & butane, synthesis of
aldrin by Diels – Alder reaction; Waste : Production & Prevention, E-factor, synthesis of ibuprofen; Water
as a reaction solvent : Concept & Synthesis of indole, reduction reactions; Microwave Irradiation in
Organic synthesis : concept, advantages, synthesis of esters, oxidation reactions, amination of ketones;
Ionic liquids : examples, concept, synthesis of 2 – phenylacrylic acid; Eco-friendly pesticides : DDT,
pyrethroids; Biocatalysis : concept, advantages, synthesis of aminopenicillanic acid; Synthesis of
vitamin C.
4. METAL FINISHING
Polarisation, decomposition potential and overvoltage, Technological importance of metal finishing. Effect
of plating variables on electrodeposits. Electroplating techniques – methods of electroplating, surface
preparation, plating of Cr. Electroless plating of copper for PCB. 5 hrs
5. ENERGY
Introduction to energy : Fuels – Definition, classification, importance of hydrocarbons as fuels.
Petroleum products : Cracking – Fluidised catalytic cracking. Reforming of petrol, knocking mechanism.
Octane number, prevention of knocking, antiknocking agents, cetane number, unleaded petrol. Power
alcohol – advantages of alcohol blended petrol, Petrochemicals from methane, ethylene, acetylene and
benzene.
Non convention energy : Introduction, types, solar energy and its significance. Solar energy conversion
technology. Solar cell materials, Photovoltaic cell, Photogalvanic cell, chalcogen photoconductors.
Applications. 7 hrs
6. HIGH POLYMERS
Definitions – Natural and synthetic polymers, mechanism of addition polymerization (free radical
mechanism), degree of polymerization, glass transition temperature. Addition and condensation polymers.
Resins and plastics : Differences between resins and plastics, thermoplastics and thermosetting plastics –
manufacture, properties and applications of HDPE and LDPE, polystyrene, phenoloformaldehyde, Teflon,
polymethyl methacrylates, polyurethanes and polycarbonates.
2K6 SYLLABUS
18
7. NEW MATERIALS
High Tc superconductors : Pervoskite, layered pervoskite and YBCO structures, valence states of Cu in
high Tc oxides. Conducting polymers : PA, PPP, PPy and other; differences between conducting
polymers and conventional conductors, soliton, polaron and bipolaron mechanisms.
Nanomaterials : Illustration of changes in band structure between bulk materials, nanosheets, nanowires
and nanoparticles, size dependent changes in band gap of semiconductors (CdS / CdSe as an example);
preparation strategies. Fullerenes : Structure of C60; preparation, reactions : Friedal Crafts reaction,
epoxidation, addition, halogenation. 5 hrs
Liquid Crystals : Classification-Thermoptropic and lyotropic, chemical constitution and liquid crystalline
behaviour, Applications; Memory materials : Introduction, shape memory effect, examples. Organic
electronic materials. 2 hrs
Reference Books :
1. Solid State Chemistry and its applications by A. R West, John Wiley , 1987
2. Engineering Chemistry by P C Jain and Monica Jain, Dhanpatrai Publishing Co. Ltd.
3. Chemistry in Engineering and Technology Vol. 1 and Vol. 2 by J. C Kuriacose and J. Rajaram,
Tata McGraw-Hill Publishing Company Ltd.
4. Chemistry of Advanced Materials by C.N. R. Rao, Blackwell Scientific Publications.
5. Solid State Chemistry Compounds by A. K. Cheethan and P. Day, Clarendon Press, Oxford, 1992.
6. An introduction to electrochemistry by Glasstone, East-West Press Pvt. Ltd, 1985.
7. Chemical and Electrochemical Energy Systems by R. Narayan and B. Viswanathan, University
Press, 1998.
8. Text book of Polymer science by F. W. Billmeyer, Jr., John Wiley and Sons, 1994.
9. Engineering Chemistry by R. Gopalan, D. Venkappayya and Nagarajan, Vikas Publishing House
Pvt. Ltd, 1999.
10. Green Chemistry An Introductory Text by Mike Lancaster, Royal Society of Chemistry, 2002.
11. Green Chemistry Environment Friendly Alternatives by Rashmi Sanghi and M. M. Srivastava,
Narosa Publishing House, 2003.
2K6 SYLLABUS
19
2K6 SYLLABUS
2K6 SYLLABUS
20
2K6 SYLLABUS
For examination an experiment each from PART – A and PART – B shall be set. Under PART-A, a
common experiment shall be set for all the candidates while under PART – B different experiment may be
set.
PART – A
1. Preparation of standard EDTA solution and determination of total hardness of water.
2. Preparation of standard EDTA solution and determination of calcium oxide in the given sample of
cement solution (rapid EDTA method).
3. Determination of Cu% in brass using standard sodium thiosulphate solution (brass solution to be
prepared by weighing the brass sample).
4. Preparation of standard dichromate solution and determination of iron in the given sample solution
of haematite ore (external indicator method).
5. Determination of manganous dioxide in the pyrolusite using potassium permanganate solution
(pyrolusite is to be weighed).
6. Determination of chemical oxygen demand of the given industrial waste water sample.
7. Estimation of Ca2+ ions in the solution of dolomite.
8. Kinetics of acid hydrolysis of methyl acetate.
PART – B
1. Determination of pKa value of a week acid using pH meter.
2. Colorimetric determination of iron / copper / any other metal.
3. Estimation of hydrochloric acid using standard sodium hydroxide solution conductometrically.
4. Determination of coefficient of viscosity of a given liquid using Ostwald’s viscometer (density of
the liquid is to be given).
PART – C
1. Demonstration of Chemistry software – Viscosity experiment, demonstration of IR spectroscopy.
2. Demonstration of gravimetric estimation of nickel using dimethylglyoxime.
3. Demonstration of organic compound synthesis using microwave irradiation (synthesis of asprin,
glucose pentaacetate, oxidation and reduction reactions).
4. Demonstration of flamephotometric determination of sodium / potassium.
2K6 SYLLABUS
21
2K6 SYLLABUS
I Semester B.E
PROGRAMMING WITH C
(Common to all branches except B.Arch)
PART – B
Chapter 5: Arrays and Strings 8 hrs
Introduction, Necessity of Arrays, Multidimensional arrays, Sorting and Searching of Arrays, Strings,
Arrays of strings, Addition and Multiplication of 2 Matrices, Functions in string.h, Programming
examples.
Chapter 6: Pointers 8 hrs
Introduction to Pointers, Declaration and Initializing of pointers, Accessing a variable through its pointer,
Pointers and Arrays, Passing Arrays to Functions, Pointers and Functions, Accessing arrays inside
functions, Programming Examples.
Chapter 7: Structures and Unions 8 hrs
Introduction, Declaring and using Structures, Structure initialization, Operations on structures, Array of
structures , Array within structure, Structures and Functions, Pointers to Structure, Pointers with in
the Structure, Union, Differences between Structure and Union, Operations on a union, Programming
Examples.
Chapter 8: Dynamic Memory Allocation 4 hrs
Introduction, Library functions for dynamic memory allocation, Dynamic multi-dimensional arrays, Self
Referential Structures, Singly linked list.
Chapter 9: Files 2 hrs
Introduction, File structure, File-handling functions, File Types, Concatenation of files.
References:
1. Mastering C: Venugopal K.R et al Tata McGraw Hill, 2006.
( Chapter: 1 to 7, 8.1 to 8.6, 8.10 to 8.13, 9, 10.1 to 10.4, 14.1 to 14.3, 15)
2. Programming in ANSI C: Balaguruswamy E, Tata McGraw Hill 1992.
3. Programming in C: Yashwanth Kanetkar P, BPB Publications, 1997.
4. The C Programming Language: Kernighan B.W and Ritchei D.M, Prentice Hall, 1971.
5. The C Odessey: Vijay Mukhy, BPB Publications.
6. C – Aptitude: Venugopal K.R, et al, Tata McGraw Hill, 2006.
2K6 SYLLABUS
22
2K6 SYLLABUS
I Semester B.E
C PROGRAMMING LAB
1. a) Write a program to determine the mean, variance and standard deviation of n numbers.
b) Write a Program to convert a given number in binary to decimal.
5. Write a program to sort the elements in ascending and descending order Using
a) Bubble sort b) Selection Sort
b)
6. a) Write a program to find whether the given string is a Palindrome or not.
b) Write a program to insert an element into an array.
11. Write a program to read and display details of students using structure.
2K6 SYLLABUS
23
2K6 SYLLABUS
2. Steam Generation
Boilers – Fire tube (Vertical Fire tube Boiler) & Water tube boiler (Babcock & Wilcox Boiler). Concept of
wet, dry and superheated stream, Enthalpy, Latent heat, dryness fraction and degree of superheat. and
Entropy, Related numerical problems. 4 Hrs
3. Energy Conversion :
Using the following
1) a) Steam turbines: impulse and reaction turbines.
2 Hrs
b) I.C. Engines: Diesel and petrol engines. Four stroke and two stroke engines. Indicated power and
brake power, mechanical efficiency and thermal efficiency, Related numerical problems. 6 Hrs
2) a) Air Compressor : Use of compressed air. Working of compressor brief introduction and
advantages of multi stage compressors.
2 Hrs
b) Refrigeration and Air Conditioning: vapour compression and vapour absorption refrigeration’s,
Principles of air conditioning 3 Hrs
PART – B
4. Fasteners:
Temporary and permanent fasteners, ISO thread profile, single and multi start threads, lead and pitch Left and
right hand threads, Hexagonal and square head bolts and Nuts, Riveted joints- single riveting and double
riveting and welded joints – T joint, V – Joint, Lap – Joint. 4 Hrs
5. Concept of Machines:
Definition: Machines, Classification of machines, Kinematics links and Pairs.
Types of Kinematics pairs (Sketches and description) 2 Hrs
6. Power Transmission:
Belt, rope, chain and gear drives. Calculation of length of belt, velocity ratio, ratio of Tensions,
power transmitted given the relevant formulae (derivation of formulae is Not included)
6 Hrs
7. Brakes, dynamometers and clutches: Functions and types of brake, dynamometers and clutches
2 Hrs
8. Bearings & Lubrication: Type of bearing, Journal bearing, & ball bearing Necessity of lubrication.
Types of lubricants, properties of a good lubricant. 3 Hrs
2K6 SYLLABUS
24
PART - C
10. Basic principles, procedures, advantages and limitations. Applications and examples involved in the
following processes.
a. Casting - 4 Hrs
b Forging - 1 Hr
c Rolling - 1 Hr
d Drawing - 1 Hr
e Extrusion - 1 Hr
f Welding - 3 Hrs
g Brazing and soldering - 1 Hr
11. Machining:
a. Lathe: Block diagram of lathe, Basic concepts in turning, taper turning and thread cutting
operations. Nomenclature of single point tool, 3 Hrs
b. Drilling: Block diagram of radial drilling machine and nomenclature of twist drill
and type of drilling operations. 3 Hrs
c. Working of CNC Machine tool
2 Hrs
References :
Note:
Question paper shall contain 8 questions, one question from each unit.
Five questions to be answered choosing atleast 2 from each part.
2K6 SYLLABUS
25
2K6 SYLLABUS
Exercises in fitting shop comprising preparation of different joints using files, hacksaw, taps, dies and
drills in 50mm by 6mm thick mild steel flats. 3 Models
Exercises in Welding shop comprising welding lap joint, butt joint, and L-Joint in 50mm wide by 6mm
thick mild steel flats. 3 Models
Exercises in carpentry shop comprising planning and chiseling and preparation of different joints like
dove-tail joint Tenon – Mortise joint and open bridle-mortise joint in 25mm x 50 mm cross section wood
3 Models.
Exercises in sheet metal shop comprising development and soldering of cylinder (base closed), cubical
box, simple funnel (made of frustums of cones/Pyramids) and rectangular tray in 22 gauge (1.2 mm
thick) G.I. sheet. 3 Models
Total: 12 Models
Scheme of Examination:-
2K6 SYLLABUS
26
2K6 SYLLABUS
II Semester B.E
6SM1201 ENGINEERING MATHEMATICS –II
(Common to Civil, Mechanical, Electrical, Electronics, Computer Science & Information Science)
PART - A
Unit-I: Differential calculus:
Indeterminate forms, evaluation of limits by L’ Hospital’s rule(without proof) , Taylor’s theorem for a
function of two variables, Taylor’s and Maclaurin’s expansions, maxima and Minima, Approximation of
errors, Methods of undetermined multipliers. 7 hrs
Unit-II: Integral calculus:
Double integrals, triple integrals, evaluation by change of order of integration, change of variables and
application to area and volume. 7 hrs
Unit-III: Vector differential calculus:
Vector valued function of a single variable: Differentiation, geometrical meaning, examples. Scalar and
vector fields, gradient of a scalar field-geometrical application- divergence and curl of a vector field –
Laplacian – vector identities. 7 hrs
Unit-IV: Vector integral calculus:
Line, surface and volume integrals of a vector function: Green’s, Stokes and Gauss’s theorem (without
proof) problems. Orthogonal curvilinear co-ordinates. 9 hrs
PART - B
Unit-V: Differential Equations:
Ordinary differential equation of first order and higher degree. Solvable for x, Solvable for p,
Solvable for y, Clairaut’s equation, Singular solutions. 7 hrs
Unit-VI: Second and higher order differential equations, Homogeneous linear equations with constant
and variable co-efficients , problems. Non homogeneous linear equations with constant and variable co-
efficients, problems, Method of variation of parameters, Method of undetermined co-efficients.
8 hrs
Unit-VII: Lap lace transforms and Gamma and Beta functions:
Definitions, Transforms of elementary functions, transforms of derivatives and integrals, Transforms of
periodic functions, unit step functions, unit impulse functions. Inverse Lap- lace transforms, convolution
theorem, solving systems of linear equations, Applications to Engineering problems.
9 hrs
Unit-VIII: Gamma functions, Beta functions, Relation between Gamma and Beta functions, problems.
8 hrs
Text Books:
1. B. S. Grewal, “Higher Engineering Mathematics” 36th Edition, 2001 Khanna Publishers, Delhi.
2. E. Kreyszig, “Advanced Engineering Mathematics” 8th Edition, 2004, John Wiley and sons.
Note:
Question paper shell contain 8 questions, one question from each unit. Five questions to be answered
choosing atleast 2 from each part.
2K6 SYLLABUS
27
2K6 SYLLABUS
II Semester B.E
6CE1201 STRENGTH OF MATERIALS
(Common to all branches except B.Arch)
PART B
5. Deflection of Beams: Introduction to elastic curve, moment curvature relation, governing
differential equation, boundary conditions, deflections of statically determinate beams by double
integration and Macaulay’s method. 8 Hrs
6. Torsion: Introduction, Basic assumptions, Torsional formula, application of torsion formula for
circular sections. Replacement of solid shaft by hollow shaft and saving in weight. Applications of
Torsion theory to closed and open coiled helical springs. 8 Hrs
7. Compound stress: Transformation of stresses, strains, in two dimension, principal stress and strains,
maximum shear stress and strains and construction of Mohr’s Circle for stresses and strains.
6 Hrs
8. Pressure Vessels: Thick and thin walled cylindrical and Spherical pressure vessels. 4 Hrs
9. Buckling of Columns: Introduction to critical load, Ideal column, Columns having different support,
effective length, slenderness ratio, Rankine’s formula. 6 Hrs
References:
1. Popov Egor P., Engineering mechanics of solids, Pearson Education Asia, Second edition, 2001.
2. Singer Ferdinand L., Strength of materials, Harper international, Third Edition, 1980.
3. Crandall Stephen H., An introduction to the mechanics of solids, McGraw Hill Book Co. 1978.
4. Bansal R.K., A textbook of strength of materials, Laxmi publication (P) Ltd., New Delhi, 2001.
5. Lehri R.S., Strength of materials and Mechanics of structures, Katson publishing, New Delhi, 1980.
6. Prasad, V.S., Mechanics of Solids, Galgotia Publication (P) Ltd., New Delhi, 2000.
2K6 SYLLABUS
28
2K6 SYLLABUS
II Semester B.E
6EC1201 BASIC ELECTRONICS
(Common to all branches except B.Arch)
Hours/Week : 4 Exam : 3 hrs
Total : 60 hrs Exam Marks – 100
PART A
1. Introduction to Electronics : What is electronics, Electronic Devices, Evolution of Electronics-
Vacuum tubes to Integrated Circuits, Conduction in Semiconductor: Electrons and holes in an
intrinsic semiconductor, conductivity of a semiconductor, carrier concentration in an Intrinsic
semiconductor, donor and acceptor impurities , charge densities in a semiconductor, Fermi level in
a semiconductor having impurities, life time of carriers, Hall effect. Introduction to Solar energy
Conversion, Photovoltaics.
7 hrs
2. Semiconductor – Diode Characteristics: Qualitative theory of a PN junction, PN Junction as a diode,
Volt – Ampere characteristics , temperature dependence of P-N characteristics, half wave and full
wave rectifiers, ripple factor, capacitor filter, Zener Diode- characteristics, Zener and avalanche
breakdown, Zener regulated power supply.
7 hrs
3. Transistor Characteristics : Junction transistor, transistor – current components, transistor as an
amplifier, common base configuration, common – emitter configuration and Common Collector
configuration with input and output characteristics, CE cutoff region, CE saturation region , large
signal , DC and small-signal CE values of current gain, operating point, bias stabilization, decibel,
Classification of amplifiers, RC coupled amplifier, frequency response, distortion in an amplifier,
cascading transistor amplifiers
12 hrs
4. Theory of Sinusoidal oscillators: Concept of feedback, sinusoidal oscillators, working of RC phase
shift, Colpitts and Hartley’s oscillator using BJT’s Expressions for frequency of oscillation (No
derivation), crystal oscillator.
4 hrs
PART B
5. Operational Amplifiers (OPAMP): Introduction, ideal OPAMP, need for OPAMP, OPAMP
characteristics, OPAMP applications: voltage follower, addition and subtraction using OPAMP
circuits, OPAMP integrating and differentiating circuits.
7 hrs
6. Communication systems: Basic block diagram of communication systems: Radio AM & FM, TV,
Overview of Mobile communication, Satellite communication, Modulation, Amplitude
Modulation , Frequency spectrum, power relations, Phase and Frequency modulation ,comparison
of AM and FM, radio telephony, super heterodyne receiver, Transmitters.
10 hrs
7. Digital Electronics: Digital logic – Binary numbers base conversion, Octal and Hexadecimal
numbers , binary addition and subtraction using One’s and Two’s complements, addition and
subtraction in Binary, Octal and Hexadecimal Number systems, BCD and EX-3 addition and
subtraction, numbers, binary logic symbols, basic theorems & properties of Boolean Algebra, De-
Morgan’s theorem. AND OR logic gate realizations using Transistor – Transistor Logic (TTL) ,
MOS, CMOS , NMOS,PMOS . Symbols used for NOT, OR, AND, NAND , NOR, XOR gates and
their truth tables, Realization of Boolean functions using basic gates. Realization of basic gates
using universal gates. 10 hrs
8. Introduction to Cathode Ray Oscilloscope (CRO) Basic block diagram, use of CRO for measurement
of amplitude Frequency and Phase.
3 hrs
Reference Books:
1.Basic Electronics M.V. Rao
2.“Electronics Devices and Circuits” Millman and Halkai, TMH 1991 Reprint 2001
3. Electrical and Electronics Computer Engineering for Scientist and Engineers, 2nd edition K.A. Krishna
Murthy and M Raghuveer, New Age International Publishers(Wiley Easter 2001
4. Electronics Communication Systems, George Kennedy (TMH 4th edition
5. Electronics Principles A.P. Malvino, TMH 6th edition
6.Digital Logic and Computer Design, Morris Mano
7.Basic Electronics by Dr. H. N. Shivashankar and B. Basavasraju.
2K6 SYLLABUS
29
8.Principles of solar energy by D. Yogi Goswami, Frank Kreith, Jan.F. Kreider., Eswar Press, Chennai.
9.Data Communication by William Schweber, Mcgraw Hill.
Note:
Question paper shall contain 8 questions, one question from each unit.
Five questions to be answered choosing at least 2 from each part.
2K6 SYLLABUS
30
2K6 SYLLABUS
II Semester B.E
6EM1201 ENGINEERING DRAWING
(Common to all branches except B.Arch)
Scheme of Examination:
3 questions from PART – A i.e., ONE on Projection of Lines, One on practical problems involving
Lines,
ONE on plane Surfaces. Student to answer any TWO questions, each of 20 Marks
2 questions from PART – B. Student to answer any ONE question of 20 Marks
3 questions from PART – C i.e., ONE on section of solids, ONE on Isometric projection of combination of
any two geometrical solids, ONE on Isometric projection of machine parts. Student to answer any 2
questions of 20 marks each.
TEXT BOOKS:
1. Engg Drawing Vol - I & Vol – II in Angle Projection Gopala Krishna K. R
2. Engg Drawing in I Angle Projection Bhatt N.D
3. Machine drawing Gopala Krishna K.R
2K6 SYLLABUS
31
2K6 SYLLABUS
II Semester B.E
6EM1202 COMPUTER AIDED DRAFTING LABORATORY
1. Introduction: System requirements for AUTOCAD, Starting AUTOCAD, Starting New Drawing,
Understanding the Interface, Co-ordinate System, Set-up for a drawing, saving the drawing,
Quitting AUTOCAD
6 Hrs
2. Drawing Objects: Points, Lines, Arcs, Circles, Regular Polygons, Rectangles, Poly lines,
Doughnuts, Traces, Text, D Text, M Text, Style.
10 Hrs
3. Object Selection and Drawing Aids: Units, Limits, Grid, Snap, OSnap, Functional Keys, Layers.
4 Hrs
5. Editing Object and Entities: Removing, Displacing, Duplicating, Orientation, Controlling Sizes,
Changing Sizes along one direction, Filleting and Chamfering.
6 Hrs.
7. Hatching and Blocks: Drawing hatch, Associative hatch, Editing hatch, Blocks- Concept, Creation,
Editing & attributes.
3 Hrs
10. Printing and Plotting of 2D & 3D objects: Creating Orthographic views multi views of Solid
objects for printing. Printing of 2D objects.
4 Hrs
Reference:
1. AUTOCAD for Engineering & Designers by Sham Tickoo. Publication: Dream tech 2005.
2. Engineering drawing by K.R.Gopala Krishna or N.D.Bhatt
3. Engineering Graphics with AUTOCAD by James. D. Bethune. Publication: Pearson Education
4. AUTOCAD manual from AUTO Desk Inc USA.
Scheme of Examination:
1. One Exercise on 2D drawing : 40 Marks
2. One exercise on 3D Solid Modeling : 40 Marks
3. Viva Voce : 20 Marks
2K6 SYLLABUS
32
Proceedings Extract of the meeting of the faculty of Engineering held on 23-05-2006 at 11.30 AM in
the Seminar Hall, UVCE, KR Circle, Bangalore
Resolutions :
• Each department has to ear mark two continuous hours on the days mentioned in the table shown :
Department Semester, Audit subject and the day on which the subject to be taught
III Semester IV Semester V Semester V Semester
Kannada Environmental Technical Report Constitution of
Science Writing India
Architecture & Civil
Monday Monday Monday Monday
Mechanical
Tuesday Tuesday Tuesday Tuesday
(Both Day & Evening)
Electrical
Wednesday Wednesday Wednesday Wednesday
Electronics
Thursday Thursday Thursday Thursday
(Both Day & Evening)
Computer Science &
Friday Friday Friday Friday
Engineering
Information Science &
Saturday Saturday Saturday Saturday
Engineering
2K6 SYLLABUS
33
¥Àæ±ÉߥÀwæPÉ ªÀiÁzÀj:
¥ÀgÁªÀıÀð£À UÀæAoÀUÀ¼ÀÄ:
2K6 SYLLABUS
34
ENVIRONMENTAL SCIENCE
(AUDIT SUBJECT)
2 hrs/ week Sess. Maximum Marks 50
Minimum Marks : 20
( 8 hrs)
Unit 6 : Social Issues and the Environment :
• From Unsustainable to Sustainable development
• Urban problems related to energy
• Water conservation, rain water harvesting and watershed management
• Resettlement and rehabilitation of people : its problems and concerns. Case studies
• Environmental ethics : Issues and possible solutions.
• Climate change, global warming, acid rain, ozone layer depletion, smog formation nuclear
accidents and holocaust. Case studies
• Wasteland reclamation.
• Consumerism and waste products.
• Environment Protection Act (EPA)
• Air (Prevention and Control of Pollution) Act
• Water (Prevention and Control of Pollution) Act
• Wildlife Protection Act
• Forest Conservation Act
• Hazardous waste (management and prevention) Act and Rules
• Issues involved in enforcement of Environmental Legislation
• Public Awareness
(7 hrs)
Unit 7 : Human Population and the Environment
• Population growth, variation among Nations
• Population explosion-Family Welfare Programme
• Environment and Human health
• Human rights
• Value education
• HIV / AIDS
• Women and Child Welfare
• Role of Information Technology in Environment and human health
• Case studies
(6 hrs)
Unit 8 : Field Work
• Visit to a local area to document environmental assets-river / forest / grassland / hill / mountain.
• Visit to a local polluted site-urban / Rural / Industrial / Agricultural
• Study of common plants, insects, birds
• Study of simple ecosystems – pond, river, hill slopes etc. (Field work equal to 5 Lecture hours)
• Each student has to submit a field report on any one of the above topics which forms the basis for
evaluation of field work for – 20 marks.
2K6 SYLLABUS
36
1. Review of Grammar : Remedial work on Tenses, Concord, Voice, Reported Speech and
Auxiliaries.
2. Writing Paragraphs :
• Topic sentences and supporting sentences.
• Using linkers in developing a paragraph.
• Developing an outline into a paragraph.
4. Presentation skills : Organization of a presentation; using blackboard, charts and digital media.
Reference Books:
2K6 SYLLABUS
37
INDIAN CONSTITUTION
(AUDIT SUBJECT)
2 hrs/ week Sess. Maximum Marks 50
Minimum Marks : 20
Chapter 5 : Issues
• Indian Federalism
• Human Rights and Environmental Protection
• Reservation and Social Justice
• Secularism
References :
2K6 SYLLABUS
38
2K6 SYLLABUS
39
Scheme for Instruction and Examination for all the Engineering Courses
(Semester Scheme)
Model question paper for Environmental Science Examination B.E/B.Tech Students (Common for all
branches)
(Audit Subject)
Time – 3 hours Max. Marks : 70
Min. Marks : 30
Pattern of Question Paper
Total : 70 Marks
Short type questions :
Sec A
(12 questions of two marks each out of which students have to answer any 10) 10 x 2 = 20
Sec B
(6 questions of five marks each out of which students have to answer any 04) 4 x 5 = 20
2K6 SYLLABUS
40
1. Differential Calculus :
UNIT I : nth derivative of standard functions, Leibnitz’s theorem (without proof)-problems.
UNIT II : Polar curves-angle between the radius vector and the tangent-pedal equations.
UNIT III : Partial differentiation, Euler’s theorem, Total differentiation, Differentiation of composite and
implicit functions-Jacobians.
18 hrs
2. Integral Calculus :
UNIT IV : Reduction formulae, Reduction formula for
∫sin x dx, ∫cos x dx and ∫sin x cos x dx Multiple Integrals; Evaluation of double and
n n m n
UNIT VII : Second and higher order linear differential equations with constant co-efficeints,
complementary functions, particular integrals (standard types).
16 hrs
4. Complex numbers :
UNIT VIII : Algebra of complex numbers, Geometrical representation and polar form of complex
numbers, Exponential form, De Moivre’s theorem (statement only), nth roots of a complex number.
10 hrs
Reference Books :
1. E Kreyszig : Advanced Engineering Mathematics, 8th edition-New Age
International.
2. B.S. Grewal : Higher Engineering Mathematics, 39th edition-Khanna Publication.
3. L. Pipes – Advanced Engineering Mathematics for Engineers and Physicists,
McGraw Hill.
Examination :
For the maximum marks of 100, 5 questions are to be answered out of 8 within 3 hrs. All questions carry
equal marks.
2K6 SYLLABUS
41
1. Analytical Geometry :
UNIT I and II : Analytical geometry in 3 dimensions : Direction cosines and Direction ratios-planes-
Straight lines-Angle between planes / Straight lines – Coplanar lines – Shortest distance between skew
lines. 16 hrs
2. Differential Calculus :
UNIT III : Mean value theorems – Rolle’s theorem (without proof), Lagrange’s and Cauchy’s mean value
theorems – Taylor’s theorem for a function of single variable (without proof), Maclaurin’s series
expansions – Indeterminate forms-L’Hospitals rule (without proof).
12 hrs
3. Vector Calculus :
UNIT IV and V : Velocity, Acceleration of a vector point function- Gradient, Divergence, Curl,
Laplacian, Solenoidal and Irrotational vectors and their properties.
UNIT VI : Vector integration – Line integral – Green’s, Gauss, Stoke’s theorem (without proof) – Simple
problems with applications to Engineering problems.
18 hrs
4. Laplace Transforms :
UNIT VII and VIII : Definition, transforms of elementary functions-transforms of derivatives and
integrals-properties, periodic functions, unit step functions and unit impulse functions, Inverse transforms
– properties-convolution theorem. Application to differential equations and simultaneous differential
equations. 14 hrs
Reference Books :
2. E Kreyszig : Advanced Engineering Mathematics, 8th edition-New Age
International.
3. B.S. Grewal : Higher Engineering Mathematics, 39th edition-Khanna Publication.
4. L. Pipes – Advanced Engineering Mathematics for Engineers and Physicists,
McGraw Hill.
Examination :
For the maximum marks of 100, 5 questions are to be answered out of 8 within 3 hrs. All questions carry
equal marks.
2K6 SYLLABUS
42
PART – A
UNIT-I
Fourier Series of periods 2π and 2l- complex from half range Fourier series-since series, Cosine series
Finite Fourier since / coline transforms – Transforms of derivatives.
UNIT-II
Infinite Fourier transforms and Inverse Fourier transforms – Simple Properties.
Complex Fourier transforms, Fourier since/cosine transforms Convolution theorem & Perseval’s Identities
(without proofs)
Z transforms – definition, Standard forms, linearity property.
UNIT-III
Bessel Functions: Solutions of the Bessel differential equation. The Bessel function, Recurrence relations,
Orthogonality, Generating function.
UNIT-IV
Legendre Polynomials: Solution of the Legendre differential equation, Legendre Polynomials, Generating
function, Recurrence relations.
PART – B
UNIT-V
Formation of Partial differential equation: Solution by Lagrange’s method for first order Partial differential
equation’s, Solution of standard types of non-linear Partial differentia equation’s – Charpit’s method.
UNIT-VI
Solution of one dimensional wave equation by the method of separation of variables and by Fourier series
method. Solution of one dimension heat equation by the method of separation of variables and by Fourier
series method.
UNIT-VII
Curve fitting by the method of least squares Peanson’s coefficient of correlation Rank correlation,
Regression lines – problems.
UNIT-VIII
Conditional probability, Baye’s theorem, Binomial/Poisson probability distribution, Normal probability
distribution.
DISTRIBUTION OF QUESTIONS:
One question each from Unit-I to Unit-VIII
References :
1. B. S. Grewal : Higher Engineering Mathematics, Khanna Publishers
2. Ejvin Kreyzig : Advances Engineering Mathematics, John Wiley & Sons
2K6 SYLLABUS
43
PART-B
4. Frequency Response of Amplifiers: Effect of coupling, emitter and bypass capacitors on low
frequency response. Analysis of different types of coupled amplifiers like RC coupled, Transformer
coupled & direct coupled amplifiers, Relative merits & demerits, Multistage amplifiers, Effect of
cascading on amplifier response (both gain & frequency response), Gain bandwidth product, Low &
High frequency compensation circuits. Tuned amplifiers, analysis of single tuned amplifiers,
expression for tuning frequency, discussion on doubled tuned and stagger turned circuits, frequency
response. 13 hrs.
5. BJT amplifiers at high frequencies: BJT hybrid- Pi model at high frequencies, Single stage CE
transistor amplifier response. 3 hrs.
6. Large Signal Amplifier: Classification, AC load line, Analysis of class A, B & AB (Push Pull &
Complementary symmetry) amplifiers, with respect to efficiency, Linearity, Harmonic distortion.
7 hrs.
REFERENCES :
1. Pulse, digital & switching waveforms - Millman & Taub, McGraw Hill International Edition.
2. Electronic Devices & Circuits - Millman & Halkias, McGraw Hill International Edition.
3. Electronic Devices & Circuits Theory - Nashelsky & Boylested, PHI -EEE.
4. Electronic Principles - Malvino, TMH Publications.
5. Electronic Principles - Gray & Campbell, Wiley Eastern.
6. Applied Electronics - Gray, Asia Publishing.
2K6 SYLLABUS
44
REFERENCES BOOKS :
2K6 SYLLABUS
45
PART-A
1. D C Generator: Constructional features, EMF equation. Armature reaction - demagnetising and
cross magnetising ampere turns. Commutation. Reactance voltage, Interpoles, compensating windings.
6 hrs
2. D C Generator Characteristics: Types - series, shunt compound and separately excited
generators. Magnetisation characteristics. Critical field resistance. Load characteristics and critical load
resistance. 6 hrs
3. D C Motors: Back emf, speed, torque of DC motors, Types- shunt series and compound -
application. 6 hrs
4. Speed Control of DC Motors: Armature voltage and field current control of dc shunt motors.
Series - parallel control of series motors. Motor starters. 6 hrs
5. Testing of DC Machines: Losses, efficiency and condition for maximum efficiency. Direct test
and indirect tests: Hopkinson, Swinburne’s & Retardation tests. Load test. 6 hrs
PART-B
6. Transformers: General principle, transformer action, types of transformers. Constructional
features, Conservator, Breather, Bushings, Cooling of transformer, EMF equation, Transformer analysis
on no load and load, equivalent circuit, 3 phase transformer connections, Tertiary windings, Scott and
open Delta connections.
Losses, separation of core loss into its components. Efficiency and condition for maximum efficiency,
All day efficiency and Regulation. Predetermination of efficiency and regulation. Parallel operation of
Single phase and Three phase transformers.
Current in rush, impact of over voltage and short circuit. No load and on load tap changers.
20 hrs
7. Auto Transformer: Single phase and Three phase Auto transformers, advantages &
disadvantages. 5 hrs
8. Testing of Single & Three phase Transformers: Polarity test, Short circuit and Open circuit
tests, Sumpner’s test. 5 hrs
REFERENCES BOOKS :
2K6 SYLLABUS
46
PART-B
6. Electronic Meters : Block schematic description of Electronic Voltmeter, True RMS Voltmeter,
Digital Voltmeter (Ramp, Integrating, Continuous Balance and SAR), Source of Error in DVM, RF
power and voltage measurements, Q meter. 6 hrs
7. Signal Sources : Function generators, Frequency synthesized signal generator, Standard signal
generators (RF), Sweep frequency generators (Direct and Indirect). 3 hrs
8. Signal Analyzing Instruments : Spectrum Analyzers – Fourier Transform Spectrum Analyzer,
Application of Spectrum Analyzer, Sensitivity of spectrum Analyzers, Distortion Analyzer, Network
Analyzer and Wave Analyzer and their applications. 4 hrs
9. Digital Analyzing Instruments : Electronic Counters, Errors in counters, Extending frequency range
of counters, Logic Analyzers. 3 hrs
10. Input Transducers for instrumentation systems : Classification, Selection, Static gauge,
Displacement, LVDT, Piezoelectric, Proximity, Thermocouple, Thermistors, Photosensitive their
characteristics and applications. 4 hrs
REFERENCES :
1. Electrical & Electronic Measurements & Instrumentation - A K Sawhney.
2. Modern Electronic Instrumentation and Measuring Techniques - Cooper & Helfrick.
3. Electrical Measurements & Measuring Instruments - Golding & Widdies, Pitman.
4. Electrical Measurements - Harris.
5. Principles of Measurement Systems - John P Beately.
6. Electrical Measurements - Stout.
7. Applied Electronics Instrumentation and Measurement – David Buchala and Wayne.
8. Electronics Measurement, New York, McGraw Hill – Terman and Petit.
9. Electronic Instrumentation – K S Kalsi.
2K6 SYLLABUS
47
2K6 SYLLABUS
48
2K6 SYLLABUS
49
PART-A
UNIT-I
Sets in the Complex plane-Functions of a complex variable-limit, continuity and differentiability-Analytic
functions-Cauchy-Riemann equations in Cartesian and polar forms. Harmonic functions
UNIT-II
Complex integration-Line integral, Cauchy theorem (Proof by Green’s theorem), Cauchy integral formula
for complex functions and for derivatives, problems.
UNIT-III
Power series-Convegrence, Radius of convergence, Taylor’s theorem and Laurent’s theorem (statement
only), problems.
UNIT-IV
Singularities, Poles, Classification of singularities, Cauchy residue theorem-Evaluation of definite integrals
∞ 2π
PART–B
UNIT-V
Algebraic and transcendental equations – solution by bisection regular-falsi, Secant’s linear-iteration and
Newton-Raphson’s methods, Aitken’s Δ2 – method.
UNIT-VI
Solution of system of linear equations, Gauss-elimination, Gaus-Jordan methods, LU-decomposition,
Choleky’s methods, Jacobi and Gauss-Seidle iteration methods.
UNIT-VII
Finite differences-Forward, Backward and Central differences – Shift operator (No derivations of relations
between operators)
Interpolation-Newton’s divided difference, Lagrange’s Interpolation formula (problems only) Numerical
differentiation based on Newton’s forward and backward difference formula.
UNIT-VIII
Numerical Integration-Trapezoidal, Simposon’s 1/3rd, Simpson’s 3/8th rule, solution of ordinary differential
equations : Euler’s, Modified Euler’s, Picard’s, Runge-Kutta II and IV order methods.
References :
1. Complex Analysis : Schaum series
2. Numerical methods for Physicus and Engineers, Iyengar, Jain and Iyengar, New Age Inte. 4th Edition.
3. Sastry : Introductory methods of Numerical analysis, PHI
2K6 SYLLABUS
50
PART-A
1. Feedback Amplifiers : Classification, Concept of feedback, Topologies of feedback amplifier, Effect
of feedback on different characteristics of feedback amplifier, Analysis of voltage series, current
series, current shunt & voltage shunt feedback amplifiers. 12 hrs.
2. Sinusoidal Oscillators : Introduction, Types of oscillators, Barkhausen criteria for sustained
oscillations, Generalized Analysis of oscillators using BJT and MOSFET. Analysis of LF oscillators -
RC phase shift (both phase lag & phase lead) & Wein bridge oscillator. Analysis of LC tuned
oscillators - Hartley, Colpitt’s & Clapp’s oscillator, Tuned collector oscillator. Crystal oscillators,
Frequency stability & amplitude stability. 12 hrs.
3. Negative resistance devices & Circuits : Negative resistance, characteristics - voltage controllable &
current controllable, Tunnel diode, UJT-VI characteristics Negative resistance phenomenon Tunnel
diode & UJT relaxation oscillator. 10 hrs.
PART-B
4. Voltage Time Base Generators : Features of time base signal, Methods of generation Bootstrap time
base generator - working & waveforms. 6 hrs.
5. DC Power Supplies : Half wave, Full wave & Bridge rectifiers - comparison, ripple factor,
efficiency, regulation, transformer utilization factor. Full wave rectifier with filters - Analysis of
capacitor, inductor, LC & Pi section filters. Regulators - Working & analysis of Zener regulator, Series
regulator with & without feedback, shunt regulator & current regulator. Short circuit protection
Voltage multipliers - Half wave & Full wave. Principles of switching regulator, its merits over linear
regulator. 20 hrs.
REFERENCES :
1. Electronic Devices and Circuits - Millman & Halkias.
2. Principles of Electronics - Kamal Choudhary.
3. Taxas instrumentation Inc - Transistor Circuit Design.
4. Pulse Digital & Switching wave forms - Millman & Taub.
5. Foundation of Electronics - Chatopadhyay.
2K6 SYLLABUS
51
2K6 SYLLABUS
52
PART-A
1. Introduction : Continuous time & Discrete time signals. Transformation of independent variable,
exponential & sinusoidal signals. Unit impulse & unit step functions. Discrete time systems & their
basic system properties. Basic system properties. Conversion of continuous – time system to
discrete time system. Modeling by discrete-time system. 10 hrs
2. Linear – Time – Invariant Systems (LTI) : Discrete time LTI systems, Convolution sum,
Continuous-time LTI systems, the convolution integral. Properties of Linear time invariant systems,
Causal LTI systems described by differential and difference equations. 10 hrs
3. Fourier series Representation of Periodic Signals : Response of LTI systems to complex
exponentials. Fourier series representation of continuous time periodic signals. Fourier series
representation of discrete time periodic signals. Fourier Series & LTI systems. Continuous time and
discrete-time Filters. 10 hrs
PART-B
4. Fourier Transform : Definition of Fourier transform & its Inverse. Properties of Fourier transform.
Fourier transform of periodic signals. Spectral density, Autocorrelation Functions, Cross-correlation
functions, and its properties. Discrete time Fourier transform & its properties, frequency Response of
discrete time systems. Hilbert Transform : Definition of Hilbert transform, Pre-envelope.
Representation of Bandpass signals and band-pass systems. 14 hrs
5. Z-transform : Definition of Z-transform & its inverse, Properties of Z-transform, Region of
convergence of Z-transform, Inverse Z-transform - inverse by long division & partial fraction
expansion methods – by evaluation of residues. Analysis & characterization of LTI systems using Z-
transforms. 10 hrs
6. Network Functions: Network functions of one port and two port Networks, poles and zeros. Time
domain response from pole zero diagram. Restrictions on pole and zero locations for driving point and
transfer functions. 6 hrs.
References Books :
1. Kamen, Heck : Fundamentals of Signals & Systems using MATLAB.
2. Oppenheim, Willsky & Nawab : Signals & Systems : PHI.
3. Carlson : Signals & Linear System Analysis : Wiley Engg.,
4. Haykins : Communication Systems : III Edition
5. Haykins : Signals & Systems : John Wiley International.
6. Nagarath et. Al, TMH, 2001.
2K6 SYLLABUS
53
Reference Books :
2K6 SYLLABUS
54
PART-A
1. Three-phase Induction Motors : Types, Construction, Rotating Magnetic Field, Principle of
Operation, Equivalent circuit, Phasor diagram, Slip, Torque equation and Maximum Torque,
Torque Slip Characteristic. Relation between Slip Rotor Copper Losses, Rotor input and
Efficiency. Free Run and Blocked Rotor Tests, Circle Diagram. Methods of starting, Star-delta
starting, Auto transformer starter, rotor resistance starter. Introduction to speed control of
Induction motor. 18 hrs.
2. Induction Generators : Negative slip, Generator Vs Motor action. Characteristics & circle
diagram.
3 hrs.
3. Single Phase Motors : Construction, Double Revolving Field theory and Principle of operation.
Starting torque and methods of starting - Split phase, Shaded pole, Capacitor start and Capacitor
run, Universal motor. Applications.
6 hrs.
PART-B
4. Synchronous Generators : Construction, Salient and non-salient pole machines, EMF equation,
different types of windings, winding factors. Fractional slot windings. Harmonics - reduction and
elimination. Armature reaction - leakage reactance and synchronous reactance. Vector diagram of
alternator (non-salient type). Transient, sub-transient and steady state reactances.
10 hrs.
5. Two Reaction Theory : Direct axis and quadrature axis synchronous reactance, vector diagram.
Slip test and regulation. Equation for power in terms of power angle for salient and non-salient
pole alternator.
4 hrs
6. Voltage Regulation : EMF, MMF, ZPF method. Short circuit ratio of alternators.
4 hrs.
7. Parallel Operation of Alternators : Effect of change of excitation and input. Conditions for
parallel operation. Synchronisation and Synchronising power, operation of alternator on infinite
bus. Division of load between two alternators, capability curves or operating chart of alternators.
7 hrs.
8. Synchronous Motor : Principle of operation, Rotating magnetic field, vector diagram for salient
and non-salient pole motor. Torque and torque angle, Blondel diagram, Effect of change in load,
Effect of change in excitation, V and inverted V curves. Synchronous condenser. Maximum
power. Hunting and damping. Methods of starting synchronous motors.
8 hrs.
REFERENCES BOOKS :
2K6 SYLLABUS
55
2K6 SYLLABUS
56
2K6 SYLLABUS
57
V SEMESTER B.E (ELECTRICAL & ELECTRONICS)
2K6EE501 CONTROL SYSTEMS ENGINEERING
(Effective from the Academic year 2008-09)
1. Modeling of Systems : Definition of Control systems, open loop and closed loop systems, types of
feedback, Modeling of Electrical, Mechanical and electromechanical systems, differential equations of
physical system. F-I and F-V analogous circuits. Linear and non-linear, continuous, discrete data, time
invariant, time variant control systems. 8 hrs
2. Block diagram and Signal flow graphs : Transfer function, block diagram representation and
reduction, signal flow graph representation and reduction using Mason’s gain formula. 8 hrs
3. Time Response of Feed back control systems : Standard test signals, steady state error analysis, unit
step response of first and second order systems, time domain specifications and transient response of a
prototype second order system. 10 hrs
4. Stability analysis : Bounded input and bounded output stability, zero input and asymptotic stability,
methods of determining stability, Routh-Hurwitz criterion. 8hrs
5. Root locus Techniques : Basic properties and construction. Procedure to construct root locus
diagrams. Analysis of simple problems using root locus. 8 hrs
6. Frequency domain analysis : Polar plots, Bode plots, Gain and Phase cross over points, Frequency
domain specifications – resonant peak, resonant frequency and bandwidth. Effect of adding a zero or
pole to the forward path transfer function. Nyquist stability criterion, relative stability using polar plot
and Bode plot. 12 hrs
7. Controllers : Design of P, PI and PID (Frequency domain approach). 6 hrs
REFERENCES :
1. Control Systems (Tata McGraw Hill, 2nd Edition, 2002) - Nagarath & Gopal.
2. Modern Control Systems, [Pearson Education, 8th Edition, 2002] – Richard C Darf and Robert H
Bishop.
3. Modern Control theory [Pearson Education, 4th Edition, 2002] – Ogata.
4. Automatic control systems (Prentice Hall New Delhi) - B C Kuo.
5. Analysis of linear systems - David K Cheng.
6. Control Systems – Nagoor Kani.
8. Problems and Solutions in Control System – A. K. Jairath
2K6 SYLLABUS
58
2. DC Machines : Main dimensions of the armature, design of armature winding and dimensions of the
slots. Design of commutator and brushes. Design of magnetic circuit and estimation of the mmf,
Design of shunt and series field windings, Design of interpoles. 15 hrs
3. Design of Transformers : Main dimensions of the core, details of winding, No load current, leakage
reactance - estimation in case of simple winding configurations, Determination of the voltage
regulation and efficiency. Design of tank, round and rectangular tubes. Design of Current transformers.
12 hrs.
4. Design of three phase induction motor : Main dimensions of the stator, details of stator winding,
dimension of the slots. Design of cage and slipring rotor & rotor windings. No load current, leakage
reactance and circle diagram. 15hrs.
5. Design of Synchronous machines : Main dimensions of the stator, details of stator windings,
dimensions of the slots. Design of rotor & rotor windings of salient and non-salient pole type
alternator. 12 hrs.
REFERENCES :
1. The performance & Design of Direct Current machines - Albert C Clayton & N N
Hancock.
2. Elements of Electrical Machine Design - Still & Siskind.
3. The Performance & Design of Alternating Current Machines - M G Say.
4. A Course in Electrical Machine Design - A K Sawhney.
Note : The students have to answer FOUR questions out of SIX questions.
2K6 SYLLABUS
59
4. INSULATORS : Materials used, types of insulators, potential distribution over a string of insulators,
methods of improving string efficiency, grading rings and arcing horns, Testing of insulators (with
mention of relevant IS standards ) 5 Hrs
5. UNDERGROUND CABLES : Comparison with overhead lines, different types of Insulating materials
used including XLPE and Gas insulation. Types of Cables, Insulation resistance, Electric stress and
Capacitance of string core cables, Grading of cables, Intersheath and capacitance grading. Capacitance of
Three core cables. 8 Hrs
6. CORONA : Phenomena of Corona, Disruptive and visual critical voltage, power loss, advantages and
disadvantages of Corona. 3 Hrs
7. LINE PARAMETERS : Inductance of single phase, two wire line, composite conductor lines, self and
mutual GMD. Inductance of three phase lines, equilateral spacing, unsymmetrical spacing, transposition,
Inductance of transposed line with unsymmetrical spacing, Bundle conductors.
Capacitance of single phase two wire lines, 3 phase lines with symmetrical spacing and unsymmetrical but
transposed lines. Ferranti effect, power loss due to charging current. Skin effect and proximity effect.
10 Hrs.
8. LINE PERFORNAMCE : Short lines, medium lines, nominal T and PI methods, long lines, ABCD
constants. 8 Hrs.
REFERENCES:
1. Transmission and Distribution by H Cotton.
2. Principles of Electrical Power Transmission by Waddicar.
3. A Course in Electrical Power by Sony, Gupta and Bhatnagar.
4. Electrical Power by S L Uppal.
5. Electrical Power Systems by C L Wadhwa.
2K6 SYLLABUS
60
V SEMESTER B.E (ELECTRICAL & ELECTRONICS)
2K6EE504 POWER ELECTRONICS
(Effective from the Academic year 2008-09)
4 hrs/ week Max. marks 125.
Exam marks: 100 Sess. marks 25.
1. Power Semiconductor Devices : Power diodes, SCR, GTO, Triac, Power transistors, Power
MOSFET, IGBT - their junction structure, Switching characteristics, Rating & applications. 6 hrs.
2. Thyristor : Junction structure, Static characteristics, Diode and two transistor analogy, dynamic turn
on and turn off characteristics, Triggering methods. R,RC,UJT triggering. Protection against OV,OC,
Snubber circuit, Thyristor ratings and protection, series and parallel operation of thyristors. 8 hrs.
3. Power Converters : Controlled rectifiers, single phase and three phase half and fully controlled
bridge feeding resistive, Inductive and DC motor loads, Free wheeling diode, effect of load and source
inductance, Dual converters and their applications. 10 hrs.
4. AC voltage controllers : ON OFF control, phase angle control, single phase uni and bidirectional
controllers with R, L, E loads, Cyclo converters. 8 hrs.
5. Turn off methods : Principle of commutation, Class A, B, C, D , Circuits and their design procedure.
6 hrs.
6. Choppers : Principle, Classifications step down, step up, buck boost, buckboost regulators and their
applications 8 hrs.
7. Inverters : 1φ and 3φ VSI, Series, Parallel, Bridge, Current source Inverters, Voltage control
techniques, Harmonic reduction, Performance analysis. 10 hrs.
8. Industrial Applications : UPS, SMPS, Speed control of motors. 4 hrs.
REFERENCES :
2K6 SYLLABUS
61
PART A
1. Electrostatics : Coulomb’s law. Electric field intensity, electrostatic potential and potential difference.
Field due to several point charges, principle of linear superposition. Concept of line charge, surface
charge and volume charge. Scalar potential and its relation with electric field. Field maps and field
cells. Gauss’s theorem and applications. Poisson’s and Laplace equations-solutions for simple cases.
Dipole, polarization and ∈r of dielectric, Capacitance calculations for different configurations. Energy
and energy density in an Electrostatic field. Boundary conditions. Displacement current and density.
Equation of continuity of currents. 16 hrs
PART B
2. Magnetostatics : Introduction. Magnetic flux and flux density. Magnetic field intensity. Biot-Savart’s
law, Ampere’s law and applications. Forces and Torque Lorentz force equation. Force acting on a
current carrying conductor. Examples on Force Calculation, Torque on a loop in magnetic field. Scalar
and vector potentials-applications. Neuman’s formula for Inductance. Inductance calculations for
simple configurations. Magnetic Dipole and µ r. Energy stored and energy density in a magnetic field.
Boundary conditions. 16 hrs
3. Time varying Electric and Magnetic fields : Introduction. Faraday’s law of electromagnetic
induction. Faraday’s law in integral and differential forms. Maxwell’s equations from different laws in
differential and integral forms. Maxwell’s equations for free space and harmonic fields. 10 hrs
4. Relationship between field and circuit theory : Application of field and circuit theory for series
circuit. Maxwell’s equations as generalization of circuit equations. 4 hrs
PART C
5. Electromagnetic Waves : Wave equations IN FREE SPACE. Rectangular plane waves in free space.
Sinusoidal plane wave propagation in Free space, Good dielectrics, good conductors and in lossy
dielectric media. Skin depth and Skin effect. Relaxation time. 8 hrs
6. Poynting Vector and flow of power : Poynting’s theorem and Poynting Vector. Instantaneous
average and complex poynting vector. Power loss in a plane conductor. Application of P-vector.
4 hrs
7. Introduction to Computational Electromagnetics using Software packages. 2 hrs
REFERENCES :
1. Electromagnetics (McGraw Hill) - John D. Kraus.
2. Electromagnetic waves and radiating systems - Jordon.
3. Engineering Electromagnetics - W. Hayt. Jr.
4. Electromagnetic fields - S. Seely.
5. Foundation of electromagnetic theory - Reitz & Milford.
2K6 SYLLABUS
62
V SEMESTER B.E (ELECTRICAL & ELECTRONICS)
2K6EE506 ELECTRICAL DRAWING
(Effective from the Academic year 2008-09)
1. IEEE symbols used in Electrical Engineering and preparation of wiring diagrams using symbols.
6 hrs.
2. DC windings : Double layer, simplex and multiplex lap and wave windings.
8 hrs
3. Three Phase AC Windings : Double layer integral and fractional slot lap and wave windings. Single
layer windings - unbifurcated, bifurcated and mush windings.
8 hrs.
4. Details of drawings : yoke and poles, armature and commutator of a DC machine, Details of stator
and rotor of alternator and induction motor. (to be dealt separately) 28 hrs.
5. Detail drawing of Single & 3 phase Transformer of Core &Shell type Transformer.
10 hrs.
REFERENCES:
1. Alternating Current Armature Windings - Siskind.
2. Electrical Drawing - K L Narang.
3. General Electrical Drawing - Surjit Singh.
2K6 SYLLABUS
63
V SEMESTER B.E (ELECTRICAL & ELECTRONICS)
2K6EE507 POWER ELECTRONICS LABORATORY
(Effective from the Academic year 2008-09)
3 hrs/ week Max. marks 125.
Exam marks: 100 Sess. marks 25.
2K6 SYLLABUS
64
PART A : MICROPROCESSORS
INTRODUCTION : Microprocessors, Classification, Microprocessor families. 2 hrs
8085 Microprocessor : Architecture, Addressing modes, Timing diagram for memory read & memory
write operations. 4 hrs
8086 Microprocessor : Architecture, Organization, Addressing modes, Instruction sets of 8086. 6 hrs
Instruction & Programming : Instruction format, Detailed instruction sets of 8086, Assembly language
programming examples: Binary & BCD arithmetic operations, Software delay generation, Searching &
Sorting, Code conversions: BCD to binary & binary to BCD code conversion. ASCII – Binary & Vice-
Versa, Use of stack subroutines & interrupts. 10 hrs
PART B : INTERFACING
Interfacing & Programmable peripheral devices : Concept of interfacing, Memory & I/O mapping.
Detailed study of interfacing devices. 8255-Programmable peripheral interface, Block diagram and
Architecture – Key Board interfacing, A / D converter, DAC converter, 8253 Timer interfacing, Square
wave generation, 8259 Programmable interrupt controller, 8257 DMA controller, 8251 Serial
Communication, 8279 Keyboard Interface. 20 hrs
PART C : MICROCONTROLLERS
INTRODUCTION : Concept of Microcontrollers, comparison of Microcontrollers against
Microprocessors. 2 hrs
8051 Microcontroller : Architecture, Addressing modes, Instruction set, Assembly Language
Programming. 16 hrs
REFERENCES :
1. Microprocessor Architecture, Programming and applications - Ramesh Gaonkar.
2. Microprocessor Fundamentals - Douglas .V. Hall.
3. Introduction to Microprocessor - A.P.Mathur.
4. Microprocessor Peripherals - Bram.
5. Design with Microcontrollers - John.B.Peatman.
6. Programming and customizing using 8051 Microcontroller—Myke Predko
7. 8051 Microcontroller—Kenneth Ayala
2K6 SYLLABUS
65
VI SEMESTER B.E (ELECTRICAL & ELECTRONICS)
2K6EE602 H V ENGINEERING
(Effective from the Academic year 2008-09)
4 hrs/ week Max. marks 125.
Exam marks: 100 Sess. marks 25.
PART A
1. Introduction: Advantages of high voltage for power transmission-prospective voltage levels. 2 hrs.
2. Generation of high voltages :
A C Voltages : Transformers in cascade. Resonant transformers – parallel and series resonant
transformers. Tesla coil.
D C Voltages : voltage doubler circuit, cockroft - Walton cascaded D C generators – Voltage
regulation, ripple, optimum number of stages. Electrostatic DC generators.
Impulse Voltages: Standard Lighting and switching voltages. Single stage impulse generators.
Multistage impulse generators. Controlled tripping - three - electrode and trigatron gap methods. Impulse
current generator. Generation of switching surge voltages. 14 hrs.
3. High Voltage & Current Measurements : R-dividers for AC and DC voltages. Generating voltmeter.
Electrostatic voltmeter, sphere gaps - Method of measurement of AC, DC and impulse voltages.
Effects of temperature, pressure, humidity and radiation. Potential dividers for impulse voltages-R, C
and RC mixed dividers. Measurement of high DC, AC and Impulse currents. Diode peak voltmeter.
10 hrs.
4. Breakdown Theory : Ionisation phsenomena, Breakdown in Gases - Townsend’s theory, Paschen’s
law, streamer’s theory of break down. Time lags of breakdown, Breakdown in Electronegative gases,
Corana discharges and breakdown in non-uniform field. Breakdown in solid and liquid dielectrics.
8 hrs.
PART B
1. Over Voltage Phenomena on Transmission lines : Causes of over voltages including lightning,
switching, faults etc. Origin of travelling waves. Partial differential equations for loss less lines and
their solution. Behavior of rectangular travelling wave at transition points - open ended line, short
circuit line, line terminated with a resistance, capacitance and inductance (R-L-C). Bewley - Lattice
diagram. Protection of transmission lines against over voltages - Horn gap, surge absorber. Ground
wires, Lightning arrestors - Silicon carbide and Zinc oxide arrestors - comparison between them with
regard to construction and characteristics. Insulation co-ordination. 10 hrs.
2. High Voltage testing of electrical apparatus :
Layout of HV Testing laboratory. Clearances, earthing and shielding. 4 hrs.
3. Non destructive HV tests on materials and apparatus: Introduction, Measurements of capacitance
and loss factor using Scherings bridge at low and high frequencies. Partial discharge measurements.
Straight and balanced methods of detection. Measurement of PD in cables and transformers. 6 hrs.
4. High voltage Testing of Electrical apparatus : HV testing of Bushings, testing of cables,
transformers and surge diverters ( to be discussed with testing circuits and procedure for important
tests as per Indian Standards). 6 hrs.
REFERENCES:
1. High Voltage Engineering (Pargamon Oxford) - Kuffel and Zangel.
2. High Voltage Engineering (TMH New Delhi) - Naidu and Kamaraju.
3. A Course in electrical Power - Soni, Gupta and Bhatnagar.
4. T & D Hand Book - Westinghouse.
5. An Introduction to HV experimental Techniques - Deterkind. (Wiley Eastern)
6. Partial discharge Measurements - IEC Specification No 270(1968) SI 6209(1971).
7. Methods of HV testing - IS 2071 - (1976).
8. Methods impulse testing - IS 2070 - (1962).
9. Insulators testing - IS 2099 - (1986), IS-731.
10. Impulse testing of transformers - IS 2026 - (1981).
11. Testing of Circuit Brakers and Isolators - IS 2516 - (1980).
12. Testing of Power cables (Part I and Part II) - IS 5959 - (1970).
13. Lighting Arrestors - IS 4004 - (1967) and IS 4850 - (1968) and IS 3070 - (1982).
14. RIV Measurements - B S 5049 (1973).
2K6 SYLLABUS
66
1. State variable analysis and Design : Introduction, Concept of State, State variables and State model of
Linear systems, Linearization of state equations. State space Representation using physical variables,
phase variables and canonical variables. State space representation of simple Electrical circuits. 16 hrs
2. Derivation of Transfer function from state model, Diagonalisation, Eigen values and Eigen vectors,
Generalized Eigen values. 6 hrs
3. Solution of state equation, State transition matrix and its properties, computation using Laplace
transformation, Power series method, Caley-Hamilton method, concept of controllability and observability,
methods of determining the same. 14 hrs
5. Phase plane method, Singular points, stability of non-linear systems, limit cycles, construction of phase
trajectories. 8 hrs.
6. Pole placement Techniques : Stability improvements by State feed back, necessary and sufficient
conditions for Arbitrary pole placement, State regular design, design state observers. 6 hrs
7. Liapunov stability criterion, Liapunov functions, Direct method of Liapunov and the non-linear system.
Hurwitz criterion and Liapunov’s direct method. 6 hrs
References :
2K6 SYLLABUS
67
16 hrs.
PULSE AND DIGITAL COMMUNICATION : Sampling theorem, PAM, PDM and PPM systems.
Introduction to Digital Communications-PCM, DM/ADM systems. Broad band communications-Mixing.
Theory and coding concepts. Hamming code. Carrier telephones. (Power line carrier communication
systems). 16 hrs.
TV TRANSMITTER AND RECEIVER : Block-diagram: Transmitter & Receiver. 6 hrs.
COMPUTER COMMUNICATIONS : Need for communication network. Distributed processing
principle of ASK, FSK & PSK. 5 hrs.
LAN NETWORK : Principles of working, Topology, Different standards. Protocols-CSMA/CD and
token passing protocols. MAN & WAN Networks. 5 hrs.
REFERENCES :
1. Electronics Communication Systems – John & Kennedy.
2. Electronics Communication – Roddy & Collen.
3. Communications – Ropbem Schoenbeck
4. Computer Communication Networks – Tannenbaum.
5. Analog & Digital Communications – Simon Haykin
2K6 SYLLABUS
68
VI SEMESTER B.E (ELECTRICAL & ELECTRONICS)
2K6EE605 AC/DC DRIVES
(Effective from the Academic year 2008-09)
4 hrs/ week Max. marks 125.
Exam marks: 100 Sess. marks 25.
REFERENCES :
2K6 SYLLABUS
69
VI SEMESTER B.E (ELECTRICAL & ELECTRONICS)
General Purpose Machines : The general purpose machine, the user’s view, the machine / assembly
language programmer’s view. The computer architect’s view, the computer system logic designer’s view,
historical perspective, Classification of computers and their instructions, Computer Instruction sets,
informal description of simple RISC computer, SRC, formal description of SRC using register transform
notation, RTN, description of addressing modes with RTN, register transfer and logic circuits: from
behaviour to hardware 12 hrs.
Real Machines: Machine characteristics and performance, RISC v/s CISC, a CISC microprocessor, the
Motorola MC 68000. 6 hrs
Processor design and microprogramming: The design process, a single bus micro architecture for the
SRC, data part implementation, logic design for the 1 – bus SRC, the control unit, the 2 and 3 bus
processor designs, the machine reset, machine exception. 10 hrs
Computer arithmetic unit: Number systems and radix conversion, fixed point arithmetic, floating point
arithmetic. 6 hrs.
Control unit: Basic concepts, hard wired and microprogrammed control unit, micro instruction format,
methods of control memory organization. 10 hrs.
Memory unit: Dynamic and static memories, memory hierarchy, virtual memory, associative memory,
cache memory, memory management, input output organization. 8 hrs.
Reference Books:
1. Vincent .P. Heuring & Harry. F. Jordan, Computer systems design & architecture, Addison-
Wesley, 1997.
2. Computer Organization : V C Hamacher, Z G Vraneric & S. G. Zaly, 4th Edition, 1996.
3. William Stallings, Computer Organization & Architecture, 4th Edition PHI.
4. I P Hayer, Computer Architecture & Organization
5. Hwang K & F A Briggs, Computer Architecture & Parallel Processing MGH 1988.
6. M.Raffiquazzaman & Rajan Chandra, Modern Computer Architecture, Galgotia 1990.
7. Computer Organization & Design, David A Patterion & John L Hennery, Morgan Karyman 1997.
2K6 SYLLABUS
70
1. PROBLEMS ON DATA TRANSFER GROUP : Memory to register and vice versa, Block
Movement, Arranging data in ascending, descending order, Software Counter, Sorting-Selection and
Bubble sort method, Searching-Linear Search Method.
3. PROBLEMS ON CODE CONVERSION AND CODING : BCD to Binary and Vice versa, Binary
to ASCII and Vice versa, 2 out of 5 Code, Palindrome etc.
4. PROBLEMS ON STACKS : Delay loop as subroutine, Multiple delay using same subroutine, Use of
monitor routines to display the information on Data and Address field.
5. PROBLEMS ON I/O OPERATIONS AND PERIPHERALS : 8255 interface and data transfer in
modes 0 and 1, Logic gate simulation, Interfacing Seven-segment display units through 8255,
Operation of 8253 in mode 3, Generation of Waveforms using DAC, Experiments on ADC-Counter
type, ASCII Display using 8279, Interfacing a 4x4 keyboard using 8255, Stepper Motor control.
2K6 SYLLABUS
71
REFERENCES:
1. Elements of Power System analysis - Stevenson.
2. Symmetrical components - Wagner Evans.
3. Modern Power System analysis - I.J. Nagrath & D.P. Kothari.
4. Symmetrical components & short circuit calculations - Dr. P.N. Reddy.
2K6 SYLLABUS
72
REFERENCES:
1. Non-Conventional Sources of Energy by G D RAI, Khanna
2. Solar Energy by Sukhatme
3. Solar Energy hand book - edited by William C Dikkinson, ASISES, Newyork.
2K6 SYLLABUS
73
PART A
1. Representation of Power System: Single line diagram of Generating Station, Substation &
Distribution System. 3 hrs
2. Switches: Isolating switches, Load break switches, Earthing switches. HRC fuses and their
applications. 3 hrs
3. Theory of Circuit interruption: Introduction. Physics of arc phenomenon. Essential properties of the
arc. Maintenance of the arc. Arc interruption theories. 6 hrs
4. Circuit Breakers: DC Circuit breaking, AC circuit breaking. Methods of arc extinction. Restriking
voltage, rate of rise of restriking voltage. Resistance switching, current chopping, capacitive and
inductive current breaking. Principle’s of arc quenching. Arc controlled devices. Requirement of an
ideal circuit breaker. Rating of circuit breakers. Types of circuit breakers, plain break, self generated
pressure oil circuit breakers. Externally generated pressure oil circuit breakers. Air circuit breakers -
low voltage air break type, arc chutes, axial blast and cross blast air circuit breakers. Advantages and
disadvantages OCB and ACB, SF6 circuit breakers. Vacuum circuit breakers, HVDC Breakers.
Testing of circuit breakers. 14 hrs
5. Switchgear: HT, LT, indoor, outdoor cubicle drawout, metal clad, SF6 switchgear. 4 hrs
PART B
6. Protective Relays: Purpose of protective relaying. Requirement of relays, sensitivity, selectivity,
reliability and speed of operation. Glossary of terms used in protective relaying like pick-up level,
reset level, zone of protection - over reach and under reach. Classification of relays. universal relay-
torque equation. 6 hrs
7. Electromagnetic Relays: Operating principles of attracted armature, solenoid and induction type
relays, over current relays, Directional over current relays. Differential relays. Distance relays.
Negative sequence relays. 5 hrs
8. Protection of apparatus: Introduction. Transformer protection. Generator protection. Motor
protection and Bus-zone protection. 5 hrs
9. Feeder Protection: Introduction – over current protection. Determination of TMS and PSM setting.
Protection of radial feeders. Parallel feeders and ring main. Distance protection. Pilot protection.
Carrier current protection. 5 hrs
10. Solid State Relays: Advantages. Application of semiconductor devices to power system protection.
Comparators. Level detectors. Logic circuit for fault detection and protection. Static over current
relays. IDMT relays. Distance relays. Two input and multi input relays. Relay with quadrilateral and
elliptic characteristics. Microprocessor based Relays 5 hrs
11. Computer Based integrated protection system. 4 hrs
REFERENCE:
1. Power protection and switchgear - Ravindranath & Chander.
2. Switchgear and protection - Despande.
3. Electrical Power - Soni, Bhatnagar & Gupta.
4. Switchgear & Protection - Sunil S Rao.
2K6 SYLLABUS
74
Discrete Fourier Transform: Introduction, definition of D.F.T & IDFT. Properties of D.F.T, Circular
convolution, Linear convolution using D.F.T, Computation of D.F.T - Decimation-in-time F.F.T
algorithm, Decimation in frequency F.F.T algorithm, Chirp Z-transform algorithm. 12 hrs
Digital Filter Structures: IIR filter structures: Direct form I & II, cascade, parallel & ladder type
realization. FIR filter structures: Direct form & Linear phase FIR structures. 6 hrs
Analog Filter Design : Butterworth low pass filters, Chebyshev low pass filters. Frequency
transformation. 8 hrs
IIR Filter Design: IIR filter design by approximation of derivatives, IIR filter design by impulse
invariance, IIR filter design by Bilinear transformation, Transformation of basic low pass filter. 12 hrs
FIR Filter Design : Characteristics of FIR digital filters, Different types of windows : Rectangular,
Bartlett, Hamming, Blackman & Kaiser windows, Design of FIR filters using windows, Design of FIR
filters by Frequency sampling method, Design of Equiripple FIR filters, Design of FIR differentiators,
Comparison of IIR & FIR digital filters. 12 hrs
Digital Signal Processors (DSPs): TMS320 & equivalent Motorola family overview, typical
applications, General description, Key features of C5X DSP processor. 10 hrs
References:
1. Terrell & L K Kwan : Digital Signal Processing A Student guide
2. Oppenheim & R W Schafer : Discrete time signal processing, PHI
3. Sanjeev K Mitra : Digital Signal Processing : McGraw Hill
4. Proakis & Monolokis : Digital Signal Processing, PHI
5. Oppenheim & Schafer et.al : Application of DSP, PHI
6. TMS Manual : Texas Instruments
7. Padmanabhan et.al: Digital Signal Processing, New Age Publishers, 2001.
8. Ingle and Proakis : Digital Signal Processing using Matlab, 2001.
9. S. Salivahanan et.al: Digital Signal Processing, TMH, 2001.
2K6 SYLLABUS
75
VII SEMESTER BE (ELECTRICAL & ELECTRONICS)
2K6EE706 POWER SYSTEMS LABORATORY – I
(Effective from the Academic year 2009-10)
3 hrs/ week Max. marks 125.
Exam marks: 100 Sess. marks 25.
1. 1) Characteristics of a) overcurrent, b) overvoltage, c) undervoltage, d) directional over current,
e) Microprocessor based Relays, f) Differential relay, g) Static overcurrent relay.
2. Short circuit studies using DC calculating board.
3. Calculation of % regulation and % efficiency of AC transmission line model.
4. Reactive power compensation
5. Protection of 3 phase induction motor.
6. Measurement of negative & zero sequence impedances of synchronous machines.
7. Power angle characteristics of synchronous machine.
8. Operation of 3-phase induction motor
a) under unbalanced voltage conditions &
b) with one line open.
2K6 SYLLABUS
76
VII SEMESTER B.E (ELECTRICAL & ELECTRONICS)
2K6EE708 ESTIMATION, ECONOMICS & MANAGEMENT
(Effective from the Academic year 2009-10)
REFERENCES:
1. Industrial organization and management - Bethel.
2. Introduction to Management - S.S. Chatterjee
3. Engineering Economics and Management - N.Narasimhaswamy.
1. Industrial Organization and Engineering Economics - T.R. Banga & S.C. Sharma.
2. Industrial Engineering and Production control systems - Praveen Kumar Khorana.
3. Managing Engineering & Technology, Babcock & Morse Pearson Education 2004.
4. Essentials of Management by Koontz, 9th Edition, McGraw Hill, 1988.
2K6 SYLLABUS
77
Light & Vision: Electromagnetic spectrum, visible spectrum, Photopic, Scotopic & Mesopic Visions –
Visual functions, Accommodation, Adaptation & Convergence. 4 hrs
Propagation of light: Light propagation, Reflection, Specular, diffuse, spread, compound, scattered &
selective reflections, Absorption, Transmission, Refraction, Polarization. 4 hrs
Photometric quantities &Units: Basic quantities – Laws of illumination from point law, surface,
photometry, spectrometry & photocells - Inter relation between the various photometric quantities,
Luminous efficacy, Spectral eye sensitivity curve, Light watt, Brightness, Luminous exitance, Radiometric
quantities & units, Point by point method of illuminance Calculations – Horizontal and Vertical
illuminance calculations. 10 hrs
Artificial light sources: Construction – principle of operation - Luminous efficacy, Lamp life & Colour
characteristics of incandescent, Tungsten halogen, fluorescent, High pressure mercury vapour, High
pressure sodium vapour and metal halide lamps – Electro luminescence &LED-LCD Displays. 8 hrs
Luminaire: Definition – optical characteristics of light control elements – classification, Symmetrical and
asymmetrical , diffuse and focussed & C.I.E. classification - Applications of various light control elements
(Reflectors, Refractors, diffusers & screening devices), Luminous intensity distribution measurements
using GONIO photometer, L.I.D. diagrams in rectangular & polar co-ordinates. 8 hrs
Artificial illumination design techniques: Utilization factor – Maintenance factor – Light output ratio –
D.L.O.R & U.L.O.R - L.D.L of various lamps – Glare – Direct & Indirect types - Designing for average
uniform illumination – Room index – space to mounting height ratio – Lumen method of calculations –
Numerical examples – IES glare index computation method – simple examples using ceiling mounted
luminaires (Calculation of initial glare index only) – Evaluation of total luminous flux output from
photometric test data. 10 hrs
Flood lighting of buildings: design aspects – Location of the equipment – Flood lighting of monuments &
sports grounds – Numerical examples. Flood light calculation. 8 hrs
Road lighting: Road lighting criteria – Luminance & Luminance ratio – Overall & Longitudinal
uniformity ratio – Zebra effect – Convectional lighting schemes – Factors affecting cost & quality of road
lighting – Lighting of curves. Energy conservation measures in illumination systems – Introduction to
optical fibers & Lasers. 8 hrs
REFERENCES:
1. Cayless M. A. & A.M. Marsden , Lamps and Lighting (3e), O & IBH Pub., 1983.
2. Ronald N. Helms, Illumination Engg. for Energy efficient luminous Environment, PH, 1980
3. Cotton H., Principles of Illumination, Chapman & Hall Ltd, London 1960.
4. Durrant D.W, Interior lighting design (5e), Lighting industry federation Ltd., 1977.
5. W. J. M Van Bommel and J. B. Boer, Road lighting, Kluwer Technical Lib, 1981.
6. Boer J. B. and D. Fischer, Interior lighting (5e), Kluwer Technical Lib, 1981.
7. I. E. S. N. A New York, Lighting Handbook (8e), 1993.
2K6 SYLLABUS
78
2. Technological aspects of embedded systems: Interfacing between analog and digital blocks, signal
conditioning digital signal processing. 12 hrs
4. Design trade offs due to process incompatibility, thermal considerations etc., 10 hrs
5. Software aspects of embedded systems, real time programming languages, operating systems for
embedded systems. 16 hrs
Reference Books:
2K6 SYLLABUS
79
PART A
PART B
6. CASE STUDY: Windows NT, Design principles, System components, environmental subsystems,
File system, networking and programmer interface. 8 hrs
Reference:
1. Silbcrschalz and Galvin, Operating System Concepts, Fifth Edition, Addision-Wesely, 1998
2. Milan Milancovic, Operating Systems, Concepts and Design, Second Edition, McGrawHill, 1992.
3. Harvey M Deital, Operating Systems, Second Edition, Addition-Wesely, 1990.
4. Dhamdhere: Systems Programming & Operating Systems, TMH, 2000.
5. Singhal & Shivaralti: Operating Systems, TMH, 2001.
6. Godbole: Operating Systems, TMH, 2001.
2K6 SYLLABUS
80
Introduction : Web Development Strategies, History of Web, Protocols governing Web, Creating
Websites for individual and Corporate World, Cyber Laws, Web Applications, Writing Web Projects,
Identification of Objects, Target Users, Web Team, Planning and Process Development. 7 hrs
HTML, XML and Scripting : List, Tables, Images, Forms, Frames, CSS, Document type definition,
XML schemes, Object Models, Presenting XML, Using XML, Processors : DOM and SAX, Introduction
to Java Script, Object in Java Script, Dynamic HTML with Java Script. 8 hrs
Java Beans and Web Servers: Introduction to Java Beans, Advantage, Properties, BDK, Introduction to
EJB, Java Beans API. Introduction to Servelets, Lifecycle, JSDK, Servlet API, Servlet Packages: HTTP
package, Working with Http request and response, Security Issues. 15 hrs
JSP : Introduction to JSP, JSP processing, JSP application design, Tomcat Server, Implicit JSP objects,
Conditional Processing, Declaring variables and methods, Error Handling and Debugging, Sharing data
between JSP pages – Sharing Session and Application Data. 15 hrs
Reference:
1. Burdman, “Collaborative Web Development” Addison Wesley.
2. Chris Bates, “Web Programming Building Internet Applications”, 2nd Edition, Wiley, Dreamtech.
3. Joel Sklar, “Principal of Web Design” Vikash and Thomas Learning.
4. Horstmann, “CoreJava”, Addison Wesley.
5. Herbert Schieldt, “The Complete Reference: Java”, TMH.
6. Hans Bergsten, “Java Server Pages”, SPD O’ Reilly.
2K6 SYLLABUS
81
1. Z-Plane Analysis of Discrete-time control systems: Impulse Sampling and data hold, obtaining the
z transform by the convolution integral method, reconstructing original signals from sampled signals, the
pulse transfer function, realization of digital controllers and digital filters. 15 hrs
2. Design of Discrete Time Control Systems by Conventional Methods : Mapping between the
s plane and the z plane, stability, analysis of closed loop systems in the z plane, transient and steady state
response analysis, design based on the root locus method, design based on the frequency response
method, analytical design method. 15 hrs
3. State Space Analysis: State space representation of discrete time systems, Solution of discrete time
state space equations, pulse transfer function matrix, discretization of continuous time state space
equations, Liapunov stability analysis. 15 hrs
4. Pole Placement and Observer Design: Controllability, Observability, useful transformations in state
space analysis and design, design via pole placement, state observers, servo systems. 15 hrs
Reference Books:
1. M. Gopal, “Digital Control and State Variable Methods”, 2nd Edition, TMH 2003.
2. Richard C Dorf, Robert H Bishop, “Modern Control System”, Pearson Education.
3. John F Dorsey, “Continuous and Discrete Control Systems”, McGraw Hill
4. Katsuhiko Ogata, “Discrete-Time Control Systems”, 2nd Edition Pearson Education, 2002.
2K6 SYLLABUS
82
1. A review of the Governing equations : A basic difference between Linear Electric machines and
rotating machines, Review of the governing equations & some simple examples, the concept of
current sheet, the air gap field equation, A design criterion, the goodness factor. 12 hrs
2. Classification of LEMS: Linear motors & levitation machines, Linear Induction motors, Linear
synchronous motors, DC linear motors, linear levitation machines. 8 hrs
3. Certain Applications of LEMS: High speed application, low speed and stand still application,
Application of Energy machines. 8 hrs
4. High speed linear induction motors: Possible arrangements for high speed LIMS, certain
phenomena in short primary LIMS, analysis of end Affects, Transverse edge effects, the exact
model of an LIM: Numerical solutions, primary windings with half-filled end slots short primary
SLIM, Design consideration: compensation of end effects. 14 hrs
5. Low Speed Linear induction motors: Flat LIM, the tabular LIM, an example. 6 hrs
6. Diverse Linear motors and oscillators: Transverse flux linear induction motors, DC linear
motor, linear stepper motor. 12 hrs
Reference books:
2K6 SYLLABUS
83
3. Induction machines: Ideal induction machine, transformation to dqo variable, basic machine
relations in dqo variables, steady state analysis. 12 hrs
Reference books:
2K6 SYLLABUS
84
Introduction to PLC : Programmable logic controller (PLC) basics, definition overview of PLC systems
– ON–OFF control concept using relay logic– Input & Output modules– Power Supplies– Isolators– PLC
installation – Trouble Shooting And Maintenance of PLC – General PLC Programming Procedures –
Programming ON–OFF Outputs. 15 hrs
PLC – Auxiliary Commands and Functions: Creating ladder diagram from process descriptions – PLC
basic functions – Register basics – Timer functions – Counter functions – Design of Interlocks & Alarms
using PLC – PLC advanced functions – Alternate Programming Languages – Analog PLC operation.
15 hrs
Automation : Introduction & Historical background – Traditional & Computer based control system
developments – Resulting System Architectures – Local Control Unit (LCU) Introduction – Basic
Elements of A Microprocessor Based Controller – Function blocks – Example of continuous control,
Logic control and Batch Reactor – Security design issues for LCU – manual back–up designs – Redundant
controller designs. 15 hrs
Text Books
1. John. W. Webb and Ronald. A. Reis, “Programmable Logic Controllers Principles and Applications”,
Prentice Hall Inc, New Jersey, 3rd edition, 1995.
2. Lukas M. P, “Distributed Control Systems”, Van Nostrand Reinhold Co, New York, 1986
References
1. Deshpande .P .B & Ash .R .H, “Elements of Computer Process Control”, Instrument Society of
America, 1981.
2. Hughes .T .A, “Programmable Controllers”, ISA, 1989.
2K6 SYLLABUS
85
Chapter I: Introduction – Different types of converters and principles of operation, Testing of converters.
8 hrs
Chapter II : Applications of Power Electronics converters in Battery charging, Welding power controls,
induction heating, Electrochemical, Dielectric heating. 10 hrs
Chapter III : Stepper motor drives – Introduction – Variable reluctance step motor, Permanent magnet
step motor, Hybrid motor, Modes of excitation in step motors, Drive circuits for step motors, Switch
reluctance motor drives. 12 hrs
Chapter V : Power conditioners and U.P.S : Introduction – Power line disturbances, Power conditioners
– UPS – different types – Principle of operation – Applications. 10 hrs
Chapter VI : Electric Utility Applications : Introduction – HVDC – Static variable control, Inter
connection of Renewable Energy sources. 8 hrs
Reference Books :
1. Power Electronics : Converters, Applications and Design by Ned Mohan, John Wiley & Sons,
1989.
2. Industrial and Power Electronics by Harish C Rai, Umesh Publication, 1994.
3. Industrial Electronics and Control by Biswanath Paul, Prentice Hall of India Publications.
2K6 SYLLABUS
86
1. Load Flow Studies: Introduction, network model formulation for load flow studies, solution of load
flow problem by Gauss seidel, Newton Raphson, Fast decoupled methods, Comparison of load flow
methods. 18 hrs.
2. Optimal system operation: Introduction, Thermal Power station performance characteristics, loss
coefficients, criteria for optimum loading of a generator connected to a bus, optimum loading of a
system taking transmission losses into account. 10 hrs.
3. Automatic generation & voltage control : Introduction, load frequency control (single area case).
8 hrs
4. Stability studies: Concept of stability - steady state, transient and dynamic stability, steady state
stability limit of a round rotor and salient rotor synchronous machine connected to infinite bus, steady
state stability limit of a two terminal pair network represented by ABCD constants, steady state
stability of a two machine system interconnected through a reactance network maintaining constant
generated voltages, steady state stability limits of two machine system interconnected through series
reactance maintaining constant terminal voltages using Clarke’s diagram. 8 hrs.
5. Transient stability: Development of swing equation for a single machine connected to infinite bus,
equal area criterion and its applications, solution of swing equation by step by step method,
determination of critical clearing time, factors affecting the transient stability, methods of improving
transient stability. 16 hrs.
REFERENCES:
1. Elements of Power system Analysis - Stevenson.
2. Power system stability vol. I - Kimbark .
3. Power system stability vol. I & II - Crary S B.
4. Modern Power system analysis - I J Nagrath, D P Kothari.
5. Computer Methods in Power system analysis - M A Pai.
Note : The students have to answer FOUR questions out of SIX questions.
2K6 SYLLABUS
87
PART A
1. D.C. Power transmission technology : Comparison of A.C. and D.C transmission, application of
D.C transmission, Description of D.C transmission systems, planning and modern trends in H.V.D.C
transmission. Economic considerations 6 hrs.
2. Analysis of HVDC Converters : Thyristor valve, valve protection, tests and recent trends. Choice of
Converter configuration. Analysis of 6 pulse bridge type converter (Graetz circuit), effect of source
inductance, equivalent circuit (without filters) converter bridge characteristics. Valve voltage wave
forms with and without overlap. Line commutated inverter with source inductance. 15 hrs.
3. Harmonics and Filters : Generation of Harmonics, types of filters, carrier frequency and RI noise.
3 hrs.
PART B
1. Converter and HVDC System Control : Principles of D.C link control, converter control
characteristics, Firing angle control current and extinction angle control, power control, higher level
controllers. 6 hrs.
2. Converter faults and protection : Converter faults, protection against over currents and over
voltages, over voltages in a Converter station. Static VAR systems, Reactive power control during
transients. 6 hrs.
3. Multiterminal HVDC Systems : Types of MTDC Systems, Control and protection of MTDC
Systems, applications of MTDC Systems. 4 hrs.
4. Stability of A.C. -D.C interconnected system. 2 hrs.
5. Simulation of HVDC Systems : Modelling of HVDC Systems for digital dynamic Simulation.
4 hrs.
PART C
2. Static variable compensations, Thyristor controlled reactor, Thyristor switched capacitor, Controllable
series compensation. 10 hrs
References :
2K6 SYLLABUS
88
1. Heating and Welding : Advantage and method of electric heating, resistance ovens, induction
heating, dielectric heating, the arc furnace, electric welding, resistance and arc welding, control
device and welding equipment. 12 hrs
2. Electrolytic process : Fundamental principles extraction refining of metals electroplating, Factors
affecting electro deposition process. 6 hrs.
3. Illumination : Laws of illumination, distribution and control, lighting calculation, factory lighting,
flood lighting, street lighting, different types of lamps, incandescent, fluorescent, vapour and CFL
and their working. Glare and its remedy, Metal halide lamps. 12 hrs
4. Electric traction : System of traction, speed time curve, tractive effort at coefficient of adhensions
selection of traction motors, method of speed control, energy saving by series parallel control, AC
traction equipment. AC series motor, characteristics, regenerative braking, linear induction motor
and their use. AC traction, diesel electric equipment, train lighting system. 20 hrs
5. Electric vehicles and systems :
Road load characteristics, city drive cycle, Power estimation, Torque estimation, Acceleration
profiling, Auxiliary loads. 2 hrs
Electric propulsion : Electric vehicles, hybrid electric vehicles, series hybrid, parallel hybrid,
combination hybrid, energy management, power flow strategies, regenerative breaking, gear train,
differential gear. 3 hrs
Prime movers : DC motor, PMDC motor, PMSM, Induction motor, drives for prime movers,
PWM strategies, inverter design, speed control strategies v/f control, vector control, field
weakening control. 3 hrs
Batteries for electric vehicles : Power density, energy density, choice of batteries, DOD for EV
batteries, Alternate energy storage mechanism. 2 hrs
Reference Books :
1. Chakraborthy, Soni, Gupta & bhatnager, A course in Electrical power, Dhanpat Rai and Sons
2. Openshaw taylor, Utilization of Electric energy (Chapter 1,2,3,6)
1. Formation of Y-Bus.
2. Formation of Z-Bus.
3. Load flow study using Newton-Raphson method.
4. Load flow study using Fast-decoupled load flow method.
5. Short circuit analysis using Z-Bus for 3 phase fault.
6. Solution of swing equation of a single machine connected to infinite bus.
7. Calculation of penalty factors and solution of co-ordination equation for economic operation of power
systems.
8. Calculation of ABCD parameters and Reactive power compensation.
2K6 SYLLABUS
89
2. HEURISTIC SEARCH : Heuristic search-An algorithm for heuristic search. Admissibility, mono
tonicity and informedness. Heuristics in games. Complexity issues. Control and implementation of state
space search-Recursion based search, pattern directed search, production systems. Predicate calculus and
planning, the black board architecture for problem solving. 8 hrs
6. EXPERT SYSTEM ARCHITECTURE : Basic components, rule based systems, forward and
backward chaining, ES features, ES development, ES categories, ES tools and examples from electric
power systems. 8 hrs
References :
1. G.F Luger and W.A Stubblefield, Artificial Intelligence – Structures and Strategies for Complex
Problem Solving, Third Edition, Addison-Wesely, 1998.
2. P.H. Winston, Artificial Intelligence, Third Edition, Addision-Wesely, 1992.
3. E Rich and Knight, Artificial Intelligence, Second Edition, TMH, 1991.
4. D W Patterson, “Introduction to Artificial Intelligence and Expert Systems”, PHI 1992.
2K6 SYLLABUS
90
60 hrs
References :
Introduction, Basic Principles of Series and Parallel resonance, Classification of Resonant converters,
Series resonant DC-DC converter, Parallel Resonant DC-DC converter, Series-Parallel DC-DC converter,
Fixed frequency control of resonant converters-Quasi-resonant converters-ZVS DC-DC converters-ZVS
Quasi resonant forward converter, ZVS multi-Resonant DC-DC converter, ZCS Quasi Resonant DC-DC
converter, ZCS clamped voltage topology, Resonant DC link converter, High Frequency link half cycle
converters, Applications.
60 hrs
Reference:
1. Ned Mohan, John Wiley & Sons – Power Electronics, Converters, Applications and Design.
2. Currents Literature.
2K6 SYLLABUS
91
PART A
1. INTRODUCTION : Image Processing as picture analysis, Advantages of interactive graphics,
Representative users of computer graphics, Classification & applications, Development of
hardware and software for computer graphics, Conceptual framework for interactive graphics,
Drawing with SRGP, Basic interaction handling, Raster graphics features, Limitations of SRGP,
Hardcopy technologies, Display technologies, Raster-scan display systems, The video controller,
Random-scan display processor, Input devices for operator interaction, Image scanners. 6 hrs
PART B
References :
1. James D Foley, Andries Van Dam, Steven K Feiner, John F Huges, Compute Graphics, Addison-
Wesley, 1997.
2. Hearn and Baker, Computer Graphics, Second Edition, PHI.
3. N. Krishnamurthy : Computer Graphics, TMH, 2002.
2K6 SYLLABUS
92
VIII SEMESTER B.E (ELECTRICAL & ELECTRONICS)
Load dispatching: Load dispatching facilities – operating restriction – installed capacity – cold reserve,
operating reserve, spinning reserve – Contingencies – Scheduled overhaul – Load characteristics –
capacity scheduling – Load duration and Load energy curves. 14 hrs
Objectives of power control: Real power balance and its effect on system frequency – Power frequency
control – Reactive power balance and its effect on system voltage – Q-V control – Structure of control
system. 8 hrs
Power frequency control: Local control – power control mechanism of an individual generator.
Mathematical model of speed governing system, speed load characteristic of governing mechanism –
Regulation of two generators in parallel – System control – Division of power system into control areas –
Tie line with frequency bias control – economic dispatch controller. 18 hrs
Reactive power voltage control: Local control – fundamental characteristic of excitation system,
generator representation, stabilizing circuit system, generation and absorption of reactive power method –
method of voltage control – injection of reactive power – tap changing transformer – regulating
transformer, voltage regulators, excitation systems 14 hrs
Recent trends: Introduction to energy control centers; Various states of a power system; SCADA systems
and RTUs. Qualitative study of real time control of power system for maintaining security. 6 hrs
REFERENCES:
1. Elgerd O.I., Electric Energy System Theory, An Introduction (e2), TMH, 1982.
2. Weedy B.M., Electric Power System (e3), Wiley, 1988.
3. Nagrath & Kothari, Power System Engineering, TMH, 1994.
3. Signal Processing : Stair case generator comparator V/f – I/f comparator, filters, Data acquaintance and
conversion, Multiplexer, Sample and hold click, ADC, DAC. 12 hrs
Digital signal transmission and processing, Modulation and Demodulation digital data transmission,
telemetry 8 hrs
Input devices and display, Analog devices & receivers, digital input output devices, semi signal, dot
matrix display LED, LCD. 8 hrs
2K6 SYLLABUS
93
INTRODUCTION : Consumption and demand patterns of different sources of Energy - both commercial
and renewable sources. Sector wise energy consumption patterns - demand projections, Energy
conservation-differential sectors (case study) 18 hrs
LOAD FORECASTING : Necessity and types of forecasting (both short term and long term).
6 hrs
DEMAND SIDE MANAGEMENT : Concept of D S M Benefits. D S M Techniques - time of day
pricing, load priority technique, peak clipping, peak shifting, valley filling. Conservation methods. Energy
efficient equipment. Some typical case of conservation.
Minimization of energy losses in transmission lines and distribution networks. 18 hrs
References :
1. Robert L Sullivan : Power system planning. McGraw Hill International Book Company
(1977).
2. D P SenGupta, K R Padiyar, Indraned Sen, M A Pai (Ed) : Recent advances in Control &
Management of Energy Systems. Interline Publishers. Bangalore (1993).
3 3. Ashok V Desai (Ed) : Energy Demand - Analysis, Management and Conservation Wiely
Eastern Ltd.
New Delhi.
4. H U D S Hand Book of Industrial Energy conservation. Van Nostrand Reinhold Company. New York
(1983).
5. Paul O’Callanghan - Energy Management. McGraw Hill Book Company, London (1993).
6. TERI Reports.
7. Current Literature.
2K6 SYLLABUS
94
1. DC – DC converters : Fly back converters, topologies, forward converter, variation, push pull
converter, limitations of push pull converter, topologies, half bridge and full bridge DC – DC
converters, High frequency inductor / transformer design, magnetic cores. 14 hrs
2. Switch mode DC power supplies : Voltage fed forward PWM control, current mode control,
digital PWM control, isolation techniques, Soft start, Current limit circuits, Over voltage
protection circuit, popular monolithic PWM control circuit & their applications. 10 hrs.
3. EMI & RFI : EMI & RFI, conducted & radiated noise, EMI suppression, EMI reduction at
source, EMI filters, EMI screening, EMI measurements & specifications. 10 hrs
4. Snubber circuits : Function & types of snubber circuits, Diode snubbers, Snubbers for thyristors,
need for snubbers with transistors, Turn off snubber, Over voltage snubber, Turn on snubber,
Snubber for bridge circuits. 8 hrs
5. Gate Drive : Preliminary Design consideration, DC coupled drive circuits, electrically isolated
drive circuits, cascade connection of drive circuits, Thyristor drive circuits, Power devices
protection in drive circuits. 8 hrs
6. Design of Magnetic components : Magnetic materials and cores, copper windings, thermal
considerations, Inductor design analysis, transformer design analysis, procedure. 10 hrs
Reference Books :
2K6 SYLLABUS
95
Materials for MEMS and microsystems: Substrates and wafers – Silicon as a substrate material, ideal
substrates for MEMS – single crystal Silicon and wafers crystal structure – mechanical properties of Si –
Silicon compounds – SiO2, SiC, Si3N4 and polycrystalline Silicon – Silicon piezoresistors – Gallium
arsenside, quartz – piezoelectric crystals – polymers for MEMS – conductive polymers. Engineering
mechanics for microsystems design: Introduction – static bending of thin plates – circular plates with edge
fixed, rectangular plate with all edges fixed and square plates with all edges fixed. Mechanical vibration -
resonant vibration – microaccelerometers – design theory and damping coefficients. Thermomechanics –
thermal stresses. Fracture mechanics – stress intensity factors, fracture toughness and interfacial fracture
mechanics. 14 hrs
Basics of fluid mechanics in macro and mesco scales: Viscosity of fluids – flow patterns Reynolds
number. Basic equation in continuum fluid dynamics – laminar fluid flow in circular conduits –
computational fluid dynamics –incompressible fluid flow in microconducts, surface tension, capillary
effect and micropumping - Fluid flow in submicrometer and nanoscale – rarefield gas, Kundsen and Mach
number and modelling of microgas flow – heat conduction in multilayered thin films – heat conduction in
solids in submicrometer scale - Thermal conductivity of thin films - heat conduction equation for thin
films. Microsystem fabrication process: Photolithography – photoresist and applications – light sources.
Ion implanation – diffusion process – oxidation – thermal oxidation – silicon diode – thermal oxidation
rates – oxide thickness by colour - Chemical vapour deposition - principle – reactants in CVD – enhanced
CVD physical vapour deposion – sputtering – deposition by epitaxy – etching – chemcial and plasma
etching. 18 hrs
2K6 SYLLABUS
96
PART A
PART B
4. LOCAL AREA NETWORKS : LAN Technology-LAN architecture, Bus/tree, ring, star, and
wireless LANs. LAN systems-Ethernet and Fast Ethernet (CSMA/CD) Token ring and FDDI, 100
VG-Any LAN, ATM LANs, Fiber channel, wireless LANs. Bridges – Bridge operation and
routing with bridges. 14 hrs
References :
2K6 SYLLABUS