Minimum Number of Pinion Teeth versus Pressure Angle
Helix Angle,
Deg. us
0° (spur gear) 32
= 32
10° a1
1p 29
20° 7
23° 5
25° 4
20° 2
35° 18
40° 15
45° 12
‘Note: Addendum 1/P,; whole depth 2.25/P,.
Minimum Number of Teeth to Avoid Undercut
When Normal Pressure Angle, ,, Deg.
TABLE 3.7
General Recommendations on Numbers of Pinion Teeth for Spur and
Helical Power Gearing
20
7
7
7
16
6
“
13
2
10
8
7
25
ivy
4
“4
B
12
un
n
10
8
7
5
25
2
2
2
1
10
10
aarone
Range of No. of
Pinion Teeth Ratio, mg Diametral Pitch, Py Hardness
19-60 119 1199 200-240 BHN
19-50 239
19-45 48
1945 119 1199 Rockwell C 33-38
19-38 239
19-35 48
19-30 119 1199 Rockwell C 38-63
17-26 239
15-24 48
Note: The maximum number of teeth in the range is based on providing a suitable
balance between strength and wear capacity. The minimum number of
teeth is intended to require either no enlargement to avoid undercutting or
no more enlargement than necessary. Small numbers of teeth in the pinion
require special tooth proportions to avoid undercut. Gears containing,
prime numbers of teeth of 101 and over may be difficult to cut on the gear
manufacturing equipment available. In general, prime numbers over 101
and all numbers over 200 should be checked with the shop to be sure the
teeth can be made.[NUMERO MINIMO DE DIENTES DEL PINION POR EFECTO DE INTERFERENCIA
20°FD 20°SD 25°FD
4,000 1.062 23 B 10 9
1063-1136 23 B it 9
1337-1265, 24 B i @
1266-1350 2 1 iL 2s
13511481 25 4 i 2
1482-1626 2 1 i 10
1.627 1.582 26 4 1 10
1.683 1.865 26 4 2 10
1867-1994 26 15 2 10
1995-2512 7 5 2 10
2513 -3.083, 28 5 RD 10
3.084339 28 16 B 10
3200-3295, 28 16 B i
3296-4616 2 16 B it
4617-6317 30, 16 B ii
ate 7328 30 7 a 1
7325-8348 a ey a a
(8.349 — 16.026 3 7 a it
16.027 A MAS 32 18 4 2
CARACTERISTICAS DE LAS MAQUINAS
LUNIFORME, MOTOR ELECTRICO, TURBINA
‘CHOQUES PEQUEROS MOTORES DE COMBUSTION INTERNA MULTICILINDRICO,
‘CHOQUES MEDIANOS 'MOTORES DE COMBUSTION INTERNA DE UN CILINDRO
\VENTILADORES CENTRIFUGOS, AGITADORES DE LIQUIDOS,
UNIFORME: "TRANSPORTADORES DE EAIAS CON ALIMENTACION UNIEORME
'SOPLADORES LOBULARES, AGITADOR DE LIQUIDOS-SOLIDO,
jHOOUES RECUENOS TRANSPORTADOR DE FAIA CON AUMENTACION VARIABLE
CaaS ‘CHANCADORAS DE MINERALES, COMPRIENSOR DE UN SOLO
CILINDRO, TRANSPORTADORES RECIPROCANTES.MODULOS ¥ PASOS DIAMETRALES NORMALIZADOS
1 25.8 1 234
4.125 257718 1% 2032
125 2032 an” 16.93933
41375 19.47273 a9" 3452822
4s 15.93823 2 127
178 3451429 2" aizase0
> 27 au" 10.16
225 1.23880 2 2.46667
25 1016 4 6.35
275 9.23635 5 5.08,
3 5.46667 6 4.23333
35 7125714 7 3.52857
+ 635 8 3.175
45 setae 9 282222
5 5.08 10 254
55 4.61818 a 2.30909
6 4.28333 2 211867
7 3.60857 4 151429
8 3.73 36 13875
° 2.82222 18 wana
10 254 20 127
1 2.30009 2 aasiss
2 2.11667 24 2.98033
14 3.81429
16 1.5875
B au
20 127
2 1.45455
2 1016
COMBINACIONES TIPICAS DE DUREZA PARA PINONES Y ENGRANAJES:
2
210 180
245 210
265 225
285 245
300 255
315 270)
335 285
350 300Procisién con ta que giran des engranajes,
Precisién de los dientes, excentcicidad, Variaciéa del perfil
Esténdar de Calidad AGMA 2000-A88,
La calidad aumente de forma progresiva de 5.0 15
“Nima ‘ier
Aplicaciin de clad Aplin ected
gure alate pa mez Gece 4-5 ale eleicn paseo
onto pen sea cement 56 tarda dere
Ingucoes para sadness soo 3-6 Prowse primie
Gaeta panes 5-1. Mezukmo de omar
os 37 Atala atonstie
Presa de pai Set par pr ta de ate
Trntprindr pc ines 3. tse eprops man
guna pre bias papel G8 toga ter ee ata
Me
nemo pata die gar 29.
‘Gierope
Impulsores para herraietes ecinicas impulses pore snc mec dite deer caidad
Velocidel de tinea 60 paso Kier Welocnded de Fnce de pase
ies) alia (mle)
oe oe
00-2 009 eH
2000-4 063 en
‘ver & 00 Ra Over 22
TABLA XVI
FACTOR DE SEGURIDAD RESPECTO A LA RESISTENCIA A LA FATIGA,
‘ALTA CONFIABILIDAD 215
DE 100 FALLA UNO 10
DE 3 FALLA UNO O7
TABLA XVII
FACTOR DE SEGURIDAD RESPECTO AL ESFUERZO DE FLUENCIA, Kx
‘ALTA CONFIABILIDAD 3.00
DISENO NORMAL 1.33