Академический Документы
Профессиональный Документы
Культура Документы
www.isotemp.com www.taitien.com
REV. -
DESCRIPTION OF REVISION
DWN. BY
APV. BY
DATE 08-04-2011
JTL
TST
1. OUTPUT(PIN = "R.F. OUTPUT") 1.1. Frequency 1.2. Initial Accuracy a. @ Temperature b. After time on power c. Within time period following date code d. @ VCO Input voltage 1.3. Waveform 1.4. Level a. "1" level b. "0" level 1.5. Load 1.6. Duty cycle 1.7. Spurious 2. FREQUENCY STABILITY 2.1. Ambient 2.2. Aging a. At time of shipment b. After indefinite storage i. Daily ii. Yearly iii. 10 years 2.3. Voltage 2.4. Short term 2.5. Load 2.6. Warm-up 2.7. Phase Noise a. @ 1 Hz b. @ 10 Hz c. @ 100 Hz d. @ 1 kHz e. @ 10 kHz
10.000 MHz < 2x10-7 +25 1C 30 3 minutes 90 days +2.0 0.001 V Rectangular HCMOS > +4.5 V < +0.5 V 15 pF 40% to 60%@ +2.5 V < -60 dBc
< 1x10-8, 0C to +70C (referenced to +25C) < 5x10-10/day < 5x10-10 after 30 days < 1x10-7 < 4x10-7 < 2x10-9/5% change < 5x10-11/second root Allan variance < 2x10-9/10% change < 1x10-7 in 5 minutes @ +25 1C (referenced to 1 hour) < < < < < -80 dBc -120 dBc -140 dBc -145 dBc -150 dBc
PAGE OF TOTAL
1 2
REV. -
OCXO 143-1000
www.isotemp.com www.taitien.com
3. ELECTRICAL FREQUENCY ADJUSTMENT (PIN = "VCO INPUT") 3.1. Range > 8x10-7 Referenced to frequency at nominal Center Voltage 3.2. Control 0 to +4.0 V 3.3. Slope Positive 3.4. Center Voltage +2.0 V NOTE: When not connected, VCO INPUT is internally held at this voltage. 3.5. Linearity < 10% 3.6. Input impedance > 100 k 4. INPUT 4.1. 4.2. 4.3. POWER (PIN = "+VDC") Voltage Current Steady state
5. ENVIRONMENTAL 5.1. Storage temperature 5.2. Vibration (non-operating) 5.3. Shock (non-operating)
-40C to +85C MIL-STD-202, Method 201 (0.06" Total p-p, 10 to 55 Hz) MIL-STD-202, Method 213, Test Condition J (30 g, 11 ms half-sine)
6. RoHS All units supplied under this MODEL NUMBER are RoHS compliant. 7. MECHANICAL(Outline drawing) 7.1. Applicable series 7.2. Model number 7.3. Outline drawing
PAGE OF TOTAL
2 2
REV. -
PIN CONNECTIONS
PIN
MOD: FREQ.: S/N: DATE:
FUNCTION
R. F. OUTPUT 0 VOLTS & CASE VCO INPUT
or
1 2
MARKING THIS SURFACE
(See Note 1)
NOT CONNECTED
REFERENCE VOLTAGE
or
4
(See Note 1)
NOT CONNECTED
or
0.026 0.66
Note 1. If the specification does not specify parameters for either PIN3 or PIN4 then that respective PIN is NOT internally CONNECTED. MARKING
C L
REV: A SHT: 1 OF 1
DWG: 125-633
Charlottesville, Virgina USA CODE I.D. NO. SCALE: 2:1 DWN. BY: BTG
07-11-2008
31785
BTG TST
UNLESS OTHERWISE SPECIFIED: ANGES: 1 DEGREE FRACTIONS: 1/32 INCH DECIMALS: .XX .015, .XXX .010 INCH
LET
REVISION
BY
APP
DATE