Вы находитесь на странице: 1из 9

HP-LP Bypass System

HP/LP Bypass System

HP-LP Bypass System HP Bypass Valve HP Bypass Spray Valve LP Bypass Valve LP Bypass Spray Valve Electro Hydraulic Actuating System

HP-LP Bypass System HP-LP Bypass System

High pressure (HP) and Low pressure (LP) bypass systems are used for quick start-up of the unit as well as during trip-out, where load rejection at the turbine does not automatically lead to a boiler trip. With a bypass system, start-up is quicker. The system diverts the steam generated by the boiler to the Re-heater/Condenser, at the same time reducing the pressure and temperature of steam, thus maintaining a minimum circulation of steam through the boiler. This enables running the boiler without the turbine in service, ensuring flow through re-heater coils. BHEL HP-LP bypass system has the following advantages : The prolonged venting of safety valves to atmosphere is avoided, thereby reducing DM water loss and cutting noise emission.
Contd...

HP-LP Bypass System HP-LP Bypass System

Sustained flow through the boiler heating surfaces is assured, ensuring Re-heater protection during start-up of units. If the grid cannot accept power, the unit can be kept running on house load. Almost all power plants are provided with HP-LP bypass systems for technical and economical reasons. The technology has been obtained from SULZER THERMTEC, Switzerland and we manufacture all the components in-house. BHEL has supplied bypass systems to over 150 power plants of 120/210/250/500 MW rating with a total installed capacity of over 32,000 MW.

HP-LP Bypass System HP-LP Bypass System


LEGEND
BP - HP BYPASS VALVE BD - SPRAY WATER ISOLATION VALVE
HRH MSL

BPE - SPRAY WATER FLOW CONTROL VALVE LBP - LP BYPASS VALVE LPC - LP COOLER LBPE - LP BYPASS SPRAY VALVE
HPT MPT LPT

BP BOILER

HPT - HIGH PRESSURE TURBINE MPT - MEDIUM PRESSURE TURBINE LPT - LOW PRESSURE TURBINE

CRH

CRHNRV LBP BPE BD

LPC CON

CRHNRV - CRH NON RETURN VALVE BFP - BOILER FEED PUMP CON - CONDENSER MSL - MAIN STEAM LINE HRH - HOT REHEAT LINE

LBPE

BFP

CRH - COLD REHEAT LINE

HP-LP Bypass System HP Bypass Valve


l Combined pressure reducing and de-superheating valve. l Steam pressure reduction by throttling and temperature reduction by spray water injection l To suit varying high pressure and temperature, the valve body is made from forged material of 2 Cr 1 Mo steel (A182 F22 Cl.3). l To keep the stresses in optimum level, valve body is made of spherical shape. l Leak tight seat. (HS 25) l Stem is made from high chrome alloy steel 11 Cr 1 Mo (X19CrMoVNbN111). l Design pressure : 200 kg/sq.cm l Design temperature : 545C

Model Nos: ARS 45, ARS 50, ARS 63, ARS 72, ARS 80, ARS 90, ARS 100, ARS 112, ARS 140 & ARS 140A

HP-LP Bypass System HP Bypass Spray Valve


l For spray water flow control to HP Bypass Valve. l Pressure reduction & flow control achieved in three stages to avoid erosion due to high pressure drop. l Valve body is of "Z" configuration made from forged carbon steel A 105. l Stem is made from high chrome alloy steel 11Cr 1Mo (X19CrMoVNbN111) l Leak Tight Stellite Seat. l Design pressure : 350 kg/sq.cm l Design temperature : 300C

Model No : E22S, E32S, E45S

HP-LP Bypass System LP Bypass Valve

l Pressure reducing valve. l Steam pressure reduction by throttling. l Valve body is made from forged material of 2 Cr 1 Mo steel (A 182 F 22 Cl.3) l Stem is made from High Chrome alloy steel 11Cr 1 Mo (X19CrMoVNbN111) l To keep the stresses at optimum level, valve body is spherical in shape. l Leak tight seat. l Design Pressure : 64 kg/sq. cm l Design Temperature : 540C

Model No : NR 64-500 EK

HP-LP Bypass System LP Bypass Spray Valve

l For spray water flow control to LP Bypass valve l Valve body is made from forged Carbon steel A 105. l Stem is made from High Chrome alloy steel 11Cr 1 Mo (X19CrMoVNbN111) l Leak tight seat. l Design Pressure : 50 kg/sq. cm l Design Temperature : 300C

HP-LP Bypass System Electro Hydraulic Actuating System


Electro hydraulic actuating system is a complete modular unit
7

with a wide range of actuator cylinders (type ASM) having a force of about 100 tonnes and large stroke.
8

It consists of an Actuator cylinder (type ASM), Oil supply unit (type OV 32B), Servo valve (type ST), Blocking unit (type BL), Step control unit (type APL), Quick stroking device (type SSB). Each actuator is equipped either with one Servo valve and

3 4 4

1 5 6

Blocking unit or a step control unit. Servo valve and blocking element control the open/close and stay-put function of the valves.

1. Actuator cylinder, type ASM 2. Oil supply unit, type OV 32B 3. Servo valve, type ST 4. Blocking unit, type BL 5. Step control unit, type APL 6. Connection plate 7. Additional accumulator 8. Quick stroking device, type SSB

Hydraulic oil required under high pressure for the operation of the valves under high steam pressure is supplied by the Oil supply unit.

Вам также может понравиться