Академический Документы
Профессиональный Документы
Культура Документы
INTERNAL
Yang Jixiang
2008-1-24
2012-04-19
HUAWEI Confidential
Page 1, Total 32
INTERNAL
Revision Record
Date 2008-1-24 2008-2-24 Revision version 0.9 1.0 Change Description Draft completed Revised part of the content and added one case Author Yang Jixiang Yang Jixiang
2012-04-19
HUAWEI Confidential
Page 2, Total 32
INTERNAL
GSM BSS Network KPI (Uplink-Downlink Balance) Optimization ManualKeywords: uplink-downlink balance, uplink-downlink level, uplink
level, downlink level, uplink-downlink imbalance Abstract: This document describes the theory, evaluation, and typical cases of the uplinkdownlink balance.
2012-04-19
HUAWEI Confidential
Page 3, Total 32
INTERNAL
Contents
1 Precondition and Assumption...........................................................8 2 Principles of Uplink-Downlink Balance............................................10
2.1 Fundamentals of the Uplink-Downlink Balance....................................................................................................10 2.1 Fundamentals of the Uplink-Downlink Balance....................................................................................................10 2.2 Evaluating the Uplink-Downlink Balance..............................................................................................................11 2.2 Evaluating the Uplink-Downlink Balance..............................................................................................................11 2.2.1 Theoretical Calculation of Uplink-Downlink Balance on Huawei Devices.....................................................12 2.2.1 Theoretical Calculation of Uplink-Downlink Balance on Huawei Devices.....................................................12 2.2.2 Evaluating the Uplink-Downlink Balance With the Uplink-downlink Balance Measurement........................13 2.2.2 Evaluating the Uplink-Downlink Balance With the Uplink-downlink Balance Measurement........................13 2.2.3 Evaluating the Uplink-Downlink Balance With the Average Uplink-Downlink Level Difference.................14 2.2.3 Evaluating the Uplink-Downlink Balance With the Average Uplink-Downlink Level Difference.................14 2.2.4 Evaluating the Uplink-Downlink Balance With the Uplink-Downlink Level Distribution.............................15 2.2.4 Evaluating the Uplink-Downlink Balance With the Uplink-Downlink Level Distribution.............................15 2.2.5 Evaluating the Uplink-Downlink Balance With the Uplink-Downlink Cumulative Distribution....................16 2.2.5 Evaluating the Uplink-Downlink Balance With the Uplink-Downlink Cumulative Distribution....................16 2.3 Effects of the Uplink-Downlink Imbalance............................................................................................................17 2.3 Effects of the Uplink-Downlink Imbalance............................................................................................................17
2012-04-19
HUAWEI Confidential
Page 4, Total 32
INTERNAL
2012-04-19
HUAWEI Confidential
Page 5, Total 32
INTERNAL
Figures
Uplink-downlink balance level...........................................................14 Distribution of differences between the uplink levels and downlink levels..............................................................................................15 Distribution of the uplink levels and downlink levels..........................16 Cumulative distribution of the uplink level and downlink level............17
2012-04-19
HUAWEI Confidential
Page 6, Total 32
INTERNAL
Tables
Mapping between the uplink-downlink balance level and the receive level (BSC6000)................................................................................12
2012-04-19
HUAWEI Confidential
Page 7, Total 32
INTERNAL
The uplink level (Rx_Lev_UP) and downlink level (Rx_Lev_UP) in this document refer to the uplink level and downlink level after the power decrease in the power control is compensated. That is: Rx_Lev_UP = RxLevUP + Power Decrease in Power Control (MS) Rx_Lev_DL = RxLevDL + Power Decrease in Power Control (BS)
Note: Only the uplink level and downlink level in the MR on the Abis interface and the power control information are considered in the calculation of the uplink level and downlink level in the
preceding formula. The static power level of the BTS does not affect the values of the uplink level and downlink level on the Abis interface, and thus does not affect the uplink-downlink balance measurement. The static power level of the TRX is counted in the calculation of the cabinet-top power. For example:
The MR of the Abis signaling consists of these messages: RxLev-ful-UP, RxLev-sub-UP, RxLev-ful-DL, RxLev-sub-DL, DTX-UP, DTX-DL, BS-Power-level, and MS-Power-level. If the uplink DTX is enabled in the cell, use the value of RxLev-sub-UP in the calculation of the uplink level; otherwise use the value of RxLev-ful-UP. If the downlink DTX is enabled in the cell, use the value of RxLev-sub-DL in the calculation of the downlink level; otherwise use the value of RxLev-ful-DL. In a GSM900 network, the MS-Power-level 5 indicates a transmit power of 33 dBm (the maximum transmit power of the MS). The MS transmit power decreases by 2 dB every time the MS power level increases by one from level 5. In a GSM1800 network, the MS-Power-level 0 indicates a transmit power of 30 dBm (the maximum transmit power of the MS). The MS transmit power decreases by 2 dB every time the MS power level increases by one from level 0. For the transmit power of a BTS, the BS-Power-level 0 indicates the maximum transmit power
2012-04-19
HUAWEI Confidential
Page 8, Total 32
INTERNAL
(the static power set for the TRX). The BTS transmit power decreases by 2 dB every time the power level increases by one from level 0. For example, if the maximum power of the TRX power amplifier is 47.8 dBm (60 W), set the static power level to 46 dBm (40 W) if the TRX power amplifier is installed in the cell. After a call is connected, the BTS sends a downlink power control message, in which the value of BS-Power-level is 2, indicating that the transmit power of the BTS is 42 dBm (46 dBm 2 x 2 dB = 42 dBm).
2012-04-19
HUAWEI Confidential
Page 9, Total 32
INTERNAL
In GSM, a two-way communication system, both the uplink and downlink have a transmit power and path loss. Balances between the uplink and downlink in each cell are required to achieve optimal system performance and to provide good voice quality during the handover and call connection. Links used for transmissions from the BTS to the MS are referred to as downlinks. Links used for transmissions from the MS to the BTS are referred to as uplinks. The uplink-downlink balance means that the uplink signal and downlink signal cover the cell edge simultaneously. The uplink-downlink imbalance means that the uplink signal and downlink signal cannot cover the cell edge simultaneously. As a result, the uplink restriction or downlink restriction occurs.
The formula for calculating the cabinet-top power is: Cabinet-top power = TRX transmit power Combiner loss Jumper loss. The remaining power (usually 10 dB) is the power required to ensure the voice quality and the connection rate taking into account the interference and loss. The diversity gain consists of the antenna diversity gain and the frequency hopping diversity 2012-04-19 HUAWEI Confidential Page 10, Total 32
INTERNAL
Due to the reciprocity of the antenna, the antenna has the same effect on the downlink and the uplink. In addition, frequency difference between the uplink and downlink in a GSM network is small; therefore, the radio transmission features are similar. Thus, the human body loss should approximate to the remaining power.
When the tower mounted amplifier (TMA) is not used and the uplink and downlink are in balance: Cabinet-top power MS receiver sensitivity = MS power + Diversity gain BTS receiver sensitivity Change the preceding formula in this way: Cabinet-top power MS power = MS receiver sensitivity + Diversity gain BTS receiver sensitivity
When the TMA is used and the uplink and downlink are in balance: Cabinet-top power MS receiver sensitivity = MS power + Diversity gain + TMA gain BTS receiver sensitivity
Change the preceding formula in this way: Cabinet-top power MS power = MS receiver sensitivity + Diversity gain + TMA gain BTS receiver sensitivity
Downlink receive level = Cabinet-top power BTS feeder loss + BTS antenna gain downlink path loss + MS antenna gain MS feeder loss Human body loss
Uplink receive level = MS power MS feeder loss + MS antenna gain Uplink path loss Human body loss + BTS antenna gain BTS feeder loss
Downlink path loss = Uplink path loss, hence, Downlink receive level Uplink receive level = Cabinet-top power MS power Formula 1
2012-04-19
HUAWEI Confidential
INTERNAL
Based on the difference calculated in Formula 1, you can evaluate the balance between the uplink and downlink. The radio signal is fluctuating. Hence, statistical analysis on the radio signal should be based on a large amount of data. A fluctuation of 3 dB can be considered in the calculation. The analysis result of adequate test data records can be used to evaluate the balance between the uplink and downlink.
2012-04-19
HUAWEI Confidential
INTERNAL
On Huawei BTSs, peak levels 8/9/10 in the uplink-downlink balance MR indicate that the uplink level and downlink level comply with the equipment performance specification and the uplink and downlink are in balance.
Take into account the cabinet-top power and MS transmit power: Cabinet-top power MS transmit power = TRX transmit power Combiner loss MS power = 47.78 - 4.5-33 = 10.28 dB < MS receiver sensitivity + Diversity gain BTS receiver sensitivity
The design power of Huawei BTS TRXs can maintain the uplink-downlink balance, and thus helps you maintain secure network operation.
2.2.2 Evaluating the Uplink-Downlink Balance With the Uplink-downlink Balance Measurement
Analyze the uplink-downlink balance according to the Uplink-and-Downlink Balance Measurement per TRX in the MR Measurement. The uplink and downlink are not in balance if either of the two formulas is true:
Rate of Number of MRs (Uplink-and-Downlink Balance Level = 1) + Rate of Number of MRs (Uplink-and-Downlink Balance Level = 2) > 15%. It indicates that the uplink is weaker or the downlink is stronger. Rate of Number of MRs (Uplink-and-Downlink Balance Level = 11) > 30%. It indicates that the downlink is stronger or the uplink is weaker. Cells with serious uplink -downlink imbalance problem can be easily sorted by using the two formulas. For the cells in which the uplink and downlink are slightly imbalanced, tracing of the Abis signaling is required. You can analyze the balance between the uplink and downlink based on the MR in the signaling tracing files.
The following example explains how to evaluate the balance between the uplink and downlink based on the Uplink-and-Downlink Balance Measurement per TRX. Figure 1 shows the distribution of the uplink and downlink balance levels in 24 hours of a day based on the Uplink-and-Downlink Balance Measurement per TRX. The cabinet-top power in the cell is 43.4 dBm. Enable the Abis signaling tracing function to check whether the uplink level and downlink level in the cell comply with the BTS performance specification and whether the uplink and downlink are in balance. The calculation based on the MRs in the signaling shows that the average difference between the uplink level and downlink level is 14 dBm, and Cabinet-top power MS power = 10.4 dB; that is, Difference between the uplink level and downlink level (Cabinet-top power MS power) = 3.6 dB. The result 3.6 dB is within the normal range.
2012-04-19
HUAWEI Confidential
INTERNAL
Hence, the formula Rate of Number of MRs (Uplink-and-Downlink Balance Level = 11) > 30% can be used to judge whether the uplink and downlink are in balance. Figure 1.1 Uplink-downlink balance level
26%
25% 20% 15% 10% 5%
21% 17%
9% 3%
Level 3 (-3..0)
10%
5%
5%
3%
Level 7 (7..8) Level 6 (6) Level 10 (16..20) Level 8 (9..11) Level 9 (12..15) Level 11 (21..26)
0%
0% Level 1 (-9)
1%
Level 2 (-8..-4)
2.2.3 Evaluating the Uplink-Downlink Balance With the Average Uplink-Downlink Level Difference
To facilitate the description, select several cells under BSC_test for data analysis. The average cabinet-top power in the cell is 40.63 dBm. Disable the power control function for all cells. Then, trace the RSL signaling on the Abis interface of the selected cells under BSC_test. Analyze the MRs obtained from the Abis signaling tracing results, calculate the average difference between the uplink level and downlink level. The average value should approximate to the difference between the cabinet-top power and MS power. A deviation of 3 dB is allowed.
2012-04-19
Level 4 (1..3)
Level 5 (4..5)
HUAWEI Confidential
GSM BSS Network KPI (Uplink-Downlink Balance) Optimization Manual Figure 1.1 Distribution of differences between the uplink levels and downlink levels
INTERNAL
D DL U L- U L L-
-4
-1
11
14
17
20
According to the calculation of the MR data, the average difference between the uplink level and downlink level is 4.72 dB. Figure 2 shows that the peak difference is 4 dB. Cabinet-top power MS power = 40.63 - 33 = 7.68 dB In BSC_test, Difference between the uplink level and downlink level (cabinet-top power - MS power) = 3 dB. The value 3 dB is within the normal range. Therefore, the uplink and downlink in the BSC area are in balance.
2.2.4 Evaluating the Uplink-Downlink Balance With the Uplink-Downlink Level Distribution
Analyze all MRs in the tracing result of the Abis signaling under BSC_test, and then analyze the distribution of the uplink level and downlink level. The analysis result is shown in Figure 3.
2012-04-19
HUAWEI Confidential
23
GSM BSS Network KPI (Uplink-Downlink Balance) Optimization Manual Figure 1.1 Distribution of the uplink levels and downlink levels
INTERNAL
500000 450000 400000 350000 300000 250000 200000 150000 100000 50000 0
Rxl ev- UL
Rxl ev- - DL
Figure 3 shows the peak value of uplink level and that of downlink level. Peak value of uplink receive level = 81 dBm Peak value of downlink receive level = 73 dBm The difference between the uplink level and downlink level is 8 dB.
Cabinet-top power MS power = 40.63 33 = 7.63 dB In the distribution of the downlink level and uplink level, the difference between the peak uplink level and the peak downlink level should approximate to the difference between the cabinet-top power and MS power. If Difference between the peak uplink level and peak downlink level (Cabinet-top power MS power) > 3 dB, the uplink and downlink are considered to be imbalanced.
2.2.5 Evaluating the Uplink-Downlink Balance With the Uplink-Downlink Cumulative Distribution
Analyze the distribution of the uplink level and downlink level with the cumulative distribution function in the ascending order of the level proportion.
2012-04-19
GSM BSS Network KPI (Uplink-Downlink Balance) Optimization Manual Figure 1.1 Cumulative distribution of the uplink level and downlink level
INTERNAL
- 110
- 106
- 102
- 98
- 94
- 90
- 86
- 82
- 78
- 74
- 70
- 66
- 62
- 58
- 54
The value corresponding to the red line in figure xx should approximate to the difference between the cabinet-top power and MS power. The balance between the uplink and downlink can easily be determined with the cumulative distribution. If the value corresponding to the red line in Figure 4 minus the difference between the cabinettop power and MS power is greater than 3 dB, the uplink and downlink are considered to be imbalanced.
2012-04-19
HUAWEI Confidential
- 50
100% 90% 80% 70% 60% 50% 40% 30% 20% 10% 0%
RxLev- U L RxLev- D L
INTERNAL
Based on the analysis of complaints for various networks and test experiences on site and in the lab, the following factors are determined to be the major factors affecting the uplink-downlink balance: Antenna and feeder installation TMA installation Incorrect parameter settings Hardware fault Repeater Antenna matching problem MS user behavior
INTERNAL
configured, the difference between the downlink level and uplink level increases by a value equal to the actual TMA gain subtracted 4 dB. In summary, when a TMA is installed in the BTS system, the uplink-and-downlink balance measurement per TRX either decreases or increases.
TMA Power Attenuation Factor The installation of a TMA results in an uplink gain, therefore, the TMA Power Attenuation Factor should be configured. If the TMA is not installed but the TMA Power Attenuation Factor is configured, then the uplink level is decreased. The difference between the downlink level and uplink level is increased. In such a case, the gain in the uplink of the BTS is decreased. The decrease can further affect the uplink receive capability of the BTS.
MS_TXPWR_MAX_CCH: MS transmit power levels are interpreted differently in GSM900 and GSM1800. In GSM900, MS power level 5 represents the full power 33 dBm. In GSM1800, however, MS power level 5 represents 20 dBm and the full power 30 dBm is represented by 0.
Be cautious when you configure the TMA Power Attenuation Factor. The factor cannot be too high. If the factor is set to an excessively high value, the uplink gain will be insufficient, which can further lead to uplink receiving problems. The TMA Power Attenuation Factor is usually set to a value equal to the TMA gain subtracted by 4 dB.
The uplink and downlink MRs are provided based on the TRX. Therefore, the uplink-downlink balance measurement per TRX can be used to analyze whether the uplink and downlink are in balance.
Faults mainly exist in the DDPU and the DTRU. TRX faults are usually caused by a faulty hardware version or the hardware fault of a certain lot. The problems occurring are usually software problems, which consist of the following: 2012-04-19 HUAWEI Confidential Page 19, Total 32
GSM BSS Network KPI (Uplink-Downlink Balance) Optimization Manual DDPU (RF front end module): Uplink gain is greater than the designed gain. Uplink gain is smaller than the designed gain. Inappropriate downlink transmit power is applied.
INTERNAL
DTRU (TRX module): Inappropriate downlink transmit power is applied. Uplink gain is greater than the designed gain. Uplink gain is smaller than the designed gain.
A specialized analyzer is required to test the abnormal uplink gain. Therefore, after identifying the uplink gain problem, send the related hardware to Huawei for further analysis with the specialized analysis.
3.5 Repeater
A variety of methods can be used to implement the function of a repeater. The application of a repeater will help obtain a certain amount of gain in both the uplink and downlink. Generally, the uplink gain and downlink gain can be adjusted. The adjustment further affects the balance between the uplink and downlink. Suppose a repeater is installed under a BTS, the uplink gain of the repeater is 6 dB, and the downlink gain of the repeater is 10 dB. In such a case, the difference between the uplink level and downlink level is 4 dB greater than the theoretical value. That is, the uplink is 4 dB weaker than the downlink. Such deviation does not affect the KPI; therefore, the adjustment is not required. Abnormal repeater gain in the uplink and downlink can also affect the balance between the uplink and downlink. If uplink-downlink imbalance is caused by the repeater, solve the problem by adjusting the repeater gain in the uplink and downlink. Along with the repeater gain adjustment, the BTS transmit power adjustment can also help rectify the uplink-downlink imbalance.
INTERNAL
2012-04-19
HUAWEI Confidential
INTERNAL
2012-04-19
HUAWEI Confidential
INTERNAL
If you save the reviewed signaling tracing results as .txt files, the .txt files can then be processed with Excel.
2012-04-19
HUAWEI Confidential
INTERNAL
The fields of messages in the tracing result should be identified when processing an MR. To identify the field of a message, do as follows: select a Measurement Result message for example; double-click the message; the MsgExplain dialog box is displayed. The field information about all messages is shown in this dialog box. For example, the Rxlev-sub-up corresponds to the six least significant bits of the 42nd bytes, and the corresponding content is 3F. You can also identify the fields of other messages in this way. To analyze problems, you usually need to identify the fields of these messages: rxlev_up(sub) rxlev_dl(sub) rxqual_up(sub) rxqual_dl(sub) rxlev_up(ful) rxlev_dl(ful) rxqual_up(ful) rxqual_dl(ful) BS_power MS_power meas_valid DTX_DL DTX_UL TA
2012-04-19
HUAWEI Confidential
INTERNAL
You may use these functions to process the fields: Hex2dec(): Convert from hexadecimal to decimal. Hex2bin(): Convert from hexadecimal to binary. Hex2dec(): Convert from binary to decimal. Trunc(): Truncates a number to a specified number of decimal places. Right(): Returns the specified number of rightmost characters of a string. Mid(): Returns a specified number of characters from a string. Note that if the Mid() function is applied to a number with zero at the left-most place, an error will occur, because the zero at the right-most place is not counted as a character. To use these functions in Excel, choose Tools > Add-Ins, and then select Analysis ToolPak and Analysis ToolPak VBA. This method can also be applied to the analysis of handover messages and immediate assignment messages.
2012-04-19
HUAWEI Confidential
INTERNAL
Are the uplink and downlink in balance in the cell? No Check the connection of the antenna and feeder in these cells. Yes Is there any problems with the antenna and feeder connection?
Yes
Yes
No Check the parameter settings in this cell. The cause of the problem is identified. The flow is complete. Yes Yes
No
No Trace the signaling on the Abis interface in the faulty cells . The hardware fault is confirmed. Send the faulty TRX to Huawei for further analysis.
Conduct fixed-position tests in the faulty cells and trace the signaling on the Abis interface.
Are the user behaviors normal in the faulty cells? Yes Replace the faulty TRX with a normal TRX.
No
Yes
No
Yes
2012-04-19
HUAWEI Confidential
INTERNAL
You can also use the average difference between the uplink level and downlink level to check for the uplink-downlink imbalance of the TRX in a cell.
If Average difference between the uplink level and downlink level (Cabinet-top power MS power) > 3 dB, the uplink level and downlink level do not comply with the BTS performance specification, and the uplink and downlink are imbalanced.
Divide the cells with the uplink-downlink imbalance into two groups based on the KPI: the group with decreased KPI (high call drop rate) takes precedence over the group with normal KPI (normal call drop rate). The processing flows for the two groups are the same.
Analyze the connections of the hardware in the cell by checking the BTS hardware type, combining mode, TMA type, repeater, antenna specification, and devices connected to the feeder. Then, check whether TMA Power Attenuation Factor and MS_TXPWR_MAX_CCH are set correctly. Check whether the repeater gain in the uplink and downlink is normal. If problems are found during the analysis process, check whether the problems are solved. The analysis flow is completed if the problems are solved. If no problems are found in the preceding analysis, go to the next step. Test the cabinet-top power: Check whether a deviation exists between the actual cabinet-top power and its theoretical value. If a deviation exists, check whether the deviation is the cause for the uplink-downlink imbalance. For example, if the cabinet-top power is 3 dB greater than its theoretical value, and the average difference between the uplink level and downlink level is 3 dB greater than its theoretical value, the uplink-downlink imbalance is caused by excessively high cabinet-top power. If the cabinet power is normal, go to the next step. Trace the RSL signaling on the Abis interface in the cells with the uplink-downlink imbalance by doing the following: retrieve the MR; analyze the uplink level, downlink level and uplinkand-downlink balance distribution in the MR of various users. Signaling of individual users can be extracted by using the Signal Analyze Tool. Without the Signal Analyze Tool, you can save the signaling tracing result as a .txt file through the Review Tracing function and then analyze the file with Excel. Check whether the uplink level, downlink level, and difference between the uplink level and downlink level are normal. If there is a problem with these values, check whether the imbalance problem occurs to part of the users or all users. Go to the next step if the 2012-04-19 HUAWEI Confidential Page 27, Total 32
GSM BSS Network KPI (Uplink-Downlink Balance) Optimization Manual imbalance problem occurs to all users.
INTERNAL
From the tracing result of the signaling on the Abis interface, you can obtain the following information: the MRs of one user (mtls-ccb), the distance between the user and the BTS (TA), the mobility of the user (fluctuation of the uplink level and downlink level), and the levels when the uplink-downlink imbalance occurs. Trace the signaling of the dialing test conducted at a fixed position: In the main lobe coverage area, dial a fixed-line phone using the test MS in frequency locking mode in a place 500m away from the antenna. The antenna should be in sight at the test position. Enable the single MS tracing function on the LMT to trace the signaling of the test MS. Move the test MS around a circle (diameter: 3m) with the test spot as the center and test for a minimum of 10 minutes. Analyze the MR in the signaling tracing result by making calculation for the uplink level and downlink level in the MR. If the difference between the uplink level and downlink level equals the difference between the cabinet-top power and MS power, you can infer that the uplinkdownlink imbalance is caused by the user behavior rather than the BTS equipment. One possible behavior is that users make calls without moving the MSs. The BTS equipment is the cause for the imbalance if either of the following is true: Difference between the uplink level and downlink level < Cabinet-top power MS power. It indicates that the uplink gain is greater than its theoretical value. Difference between the uplink level and downlink level > Cabinet-top power MS power. It indicates that the uplink gain is smaller than its theoretical value. Confirm that the uplink gain is abnormal, and then return the faulty DDPU and DTRU to Huawei for further analysis. The uplink level and downlink level in the test can be used to determine the uplink gain and downlink gain. Typically, at a spot 500m away from the antenna, the cabinet-top power is 44 dBm, the antenna gain is 17 dB, the uplink level is about -73 dBm, and the downlink level is about -61 dBm. The signal strength at a spot within 500m from the antenna varies with reflections; therefore, the uplink level and downlink level are for reference only. The difference between the uplink level and downlink level, however, can be used to analyze whether the uplink and downlink are in balance. If Average difference between the uplink level and downlink level (Cabinet-top power MS power) > 3 dB, the uplink and downlink are imbalanced. If the cabinet-top power is determined to be normal in a cell where the uplink and downlink are imbalanced, you can infer that the uplink gain is abnormal. Then, go to the next step.
After you infer that the uplink gain on site is abnormal, replace the DDPU with a normal DDPU to check whether the uplink gain in the DDPU or that in the DTRU is abnormal. If the uplink and downlink are balanced after replacing the DDPU, the uplink gain associated with the DDPU in the problematic cell is abnormal. If the uplink and downlink are still imbalanced after replacing the DDPU, the uplink gain associated with the DTRU in the problematic cell is abnormal. When the hardware problem is confirmed, return the hardware to Huawei in time for further analysis.
2012-04-19
HUAWEI Confidential
INTERNAL
5
Problem Description Analysis and Solution
The following bar chart shows the uplink-downlink balance measurement distribution from 8:00 to 14:00 on Dec., 25th, 2007 in two cells, cell A and cell B.
30% 25% 20% 15% 10% 5% 0% 3. 9% 0% -9 1% ( - 8, - 7, - 6, - 5, - 4) 5% 2% ( - 3, - 2, - 1, 0) ( 1, 2, 3) ( 4, 5) 6 ( 7, 8) ( 9, 10, 11) 6% 4. 5% 4% 6. 3% 5. 8% 3. 1% 1. 0% ( 12, 13, 14, 15) ( 16, 17, 18, 19, 20) 5% 0. 5% ( > 21) = 15. 2% 12. 6% 12% 16% 25. 5% 21. 4% 22%
Cell A
Cell B
27%
Trace the signaling messages on the RSL over the Abis interface and analyze the MRsThe uplink-downlink balance measurement results of all users in the two cells differentiate greatly. Calculate the average difference between the uplink level and downlink level in all MRs of the signaling tracing results in the two cells. In cell A, the difference is 3 dB; in cell B, the difference is 11.24 dB.
2012-04-19
HUAWEI Confidential
INTERNAL
Test the transmit power of the two BTSs on site. The test shows that the transmit power of the DTRU is normal. The cabinet-top power complies with the theoretical value. In cell A, the cabinet-top power is 4 dBm; in cell B, the cabinet-top power is 43 dBm.
Calculate the difference between the uplink level and downlink level with formula 3: Uplink receive level - Downlink receive level = Cabinet-top power MS power Cell A: Cabinet-top power MS power = 41 33 = 8 Cell B: Cabinet-top power MS power = 43 33 = 10 Obviously, the uplink gain in cell A is abnormal (4 dB5 dB beyond the normal range).
Measure the uplink receive gain of the DDPU with a vector analyzer to ensure that the uplink gain is at least 3 dB greater than the designed value.
The software analysis shows that an error occurs when configuring the LNA gain for this DDPU version. Note: In the old DDPU (48.1.1), the LNA gain is set to an absolute value. No error occurs when configuring the LNA gain. Version 48.1.0 and later versions of the DDPU all work properly. In the new DDPU (48.1.0), the LNA gain in software versions earlier than V100R001C07B229 (V100R001C07B229 not included) is set to an absolute value. An error occurs when configuring the LNA gain. In the new DDPU (48.1.0), the LNA gain in software versions later than V100R001C07B229 (V100R001C07B229 not included) is set to a relative value. No error occurs when configuring the LNA gain.
INTERNAL
The cabinet-top transmit power is tested and is found to be normal. Thus, the downlink transmit power is normal.
Analyze the KPIs of this cell. The KPIs are found to be normal. We suspect that the software on the faulty TRX is not running properly; as a result, the reported uplink level on the Abis interface is smaller compared with its actual value.
The faulty TRX is sent to Huawei lab for further analysis. The analysis shows that when reporting the uplink received signal strength indicator (RSSI), the negative symbol or positive symbol in the compensation value reported by the compensation program is reversed. Consequently, the measurement shows the uplink-downlink imbalance.
To solve the problem, upgrade the software version and test in the lab. The solution is incorporated into version V100R001C07B239 and later versions.
Analyze the tracing result of the Abis signaling and the uplink level is found to be excessively low.
Check the maximum transmit power of the MS in the MR. The maximum transmit power is incorrectly set to 5.
Modify the parameter settings of this cell: set the maximum transmit power of the MS to 0. The problem is solved.
2012-04-19
HUAWEI Confidential
INTERNAL
2012-04-19
HUAWEI Confidential