Академический Документы
Профессиональный Документы
Культура Документы
Step 1
Valet/Override Switch
ON ON
Step 2
Step 3
Step 4
1x
ON
OFF
OFF
Switch in On Position
Turn On Ignition
Step 5
Step 6
Regular
Arm/Dis #2
Step 7
#2
2x
Regular
Arm/Dis
#2
Regular
Arm/Dis
Code Hopping
1x
LOCK UNLOCK PANIC AUX
Switch the Valet Switch On then Off 2 Times
To Code #2 Button
The LED will begin flashing slowly and the horn /siren will emit 1 short chirp. Switch the Valet Switch On then Off 1 Time The horn/siren will chirp 1 time. The code has now been learned. You are now in the transmitter Note 1: Regular transmitters supplied are Not coded alike so you need to code in the second trans- The LED will be solid red and the mitter now by pushing the Arm/Dis button on the second transmitter. Go to Step 7. code programming mode. The horn/siren will chirp 1 time. Note 2: Code Hopping transmitters supplied are Not coded alike so you need to code in the secLED will be a solid RED. ond transmitter now by pushing the Lock button on the second transmitter. Note 3: If you are coding a Code Hopping transmitters, skip steps 7 and 8 and go to step 9. No further coding procedures are necessary. Code hopping transmitters learn all button functions when the Lock button is learned.
Step 8
Step 9
R
O FF
Turn Off the Ignition
Copyright 1997 Magnadyne Corporation
The LED will begin flashing slowly and the horn / siren will chirp 2 The horn /siren will emit 1 short times. chirp and 1 long chirp. You are Note 1: Regular transmitters supplied are Not coded alike so now out of the consumer transmityou need to code in the second transmitter now by pushing the #2 ter code learning mode. The LED is off. button on the second transmitter.
When the Carbine security system control module learns the transmitter operating code, a specific group of operating features are automatically programmed to a default setting. These default settings can be changed by following the enclosed procedure and using the consumer transmitter for programming. # 1 2 3 Programmable Alarm Feature Chirp Status Indicator Last Door Closed Automatic Arming Ignition Key Controlled Door Lock/ Unlock Default Setting On Automatic Arming of Alarm Off Off
Step 1
Valet/Override Switch
ON ON
Step 2
Step 3
Step 4
OFF
OFF
Switch in On Position
6x
ON
R
Step 5
Regular
Arm/Dis #2
Step 6
#2
Regular
Arm/Dis
#2
Regular
Arm/Dis
Code Hopping
LOCK UNLOCK PANIC AUX
O FF
# Transmitter Button
Confirmation = Change Function 1 Beep = Chirp Status Indication On * 2 Beeps = Chirp Status Indication Off 1 Beep = Automatic Arming On, Alarm will arm 10 seconds after door is closed and rearm 10 seconds after remote disarm. 2 Beeps = Automatic Arming On, Alarm will arm 20 seconds after door is closed and rearm 20 seconds after remote disarm. 3 Beeps = Automatic Arming On, Alarm will arm 30 seconds after door is closed and rearm 60 seconds after remote disarm. 4 Beeps = Automatic Arming Off * 1 Beep = Door will Lock 3 seconds after Ignition is Turned On. Door will not Unlock when Ignition is Turned Off. 2 Beeps = Door will Lock 3 seconds after Ignition is Turned On Door will Unlock when Ignition is Turned Off. 3 Beeps = Door will not Lock 3 seconds after Ignition is Turned On. Door will not Unlock when Ignition is Turned Off *.
3 ARM/DIS + #2
or LOCK + UNLOCK