Академический Документы
Профессиональный Документы
Культура Документы
! Antes:
L1 S1
N
L1 L1
! Ahora:
L1 S1
1
No1 No2 No3
L1
LOGO!
Q1
LOGO!
Si una desconexin ocurre mientras el programa era entrado, el progrma se borra una vez que se recobra la tensin Antes de Power OFF Despus de Power ON SIEMENS I : 0. , 1. , 2. 123456789 0123456789 01234 LOGO! SIEMENS I : 0. , 1. , 2. 123456789 0123456789 01234 LOGO!
En modo RUN
ESC
OK
SIEMENS
>
LOGO!
SIEMENS Program ..
>
LOGO! 12/24 RC
>
Q1
ESC OK
LOGO!
I1
Q1
&
I2
>
I1
Q1
Q2
3. However, you cannot connect an output to a input preceding it in the same path (no feedback loops).
&
&
B01 x & Q1
OK
B01 Co & Q1
OK
B01 & Q1
OK
B01 & Q1
OK
BF
Q1
B01 Q1 Co Q1
Programa Inicial
Refer to the following parallel circuit containing two switches.
S1
S2
K1
Switch S1 and switch S2 switch the load. The parallel circuit of S1 and S2 is an OR operation in LOGO!, because S1 or S2 switches on the output.
K1 v
E1
I1 I2 x
>1 Q1
Cableado
L1 N S1 L1 N S2 I1 I2 I3 I4 I5 I6 I7 I8
Switch S1 acts on input I1 and switch S2 acts on input I2. The load is connected at relay Q1.
SIEMENS
You now enter the program (from the output to the input!). To start, LOGO! displays output Q1. Q1
ESC OK
LOGO! 12/24 RC
Below the Q of Q1, you see an underscore (_). We refer to the underscore as a cursor. The cursor indicates your current location in the program.
Q1
Q2
Q3
Q4
The cursor indicates your location in the program. You enter the first block (the OR block) at this location. OK Change to editing mode by pressing .
SIEMENS
LOGO! 12/24 RC
Q1
ESC OK
The cursor now appears as a solid block Now, use the the following: Connector (Co) Basic function (BF) Special function (SF) keys to select one of
LOGO! 12/24 RC
SIEMENS
Co
Q1
ESC OK
LOGO!
SIEMENS
BF
Q1
ESC OK
LOGO! 12/24 RC
SIEMENS
B01 >1 Q1
ESC OK
SIEMENS
B01 >1 Q1
ESC OK
LOGO! 12/24 RC
SIEMENS
B01
The first element in the list (Co) is an x, which is the character for input not used. Select input I1 using the keys.
LOGO!
OK.
SIEMENS
B01 I1 >1 Q1
ESC OK
SIEMENS
I1 I2
We do not need the last input of the OR block for this program. In a LOGO! program, we designate an unused input with an x. You now know the principle behind doing this: 1. Change to editor mode with 2. Select the Co list with 3. Accept the Co list with 4. Select x with 5. Accept x with OK
OK OK
SIEMENS
B01 I1 I2 x LOGO! >1 Q1
ESC OK
Arrancando un Programa
Now, all inputs of the block are connected. LOGO! considers the program to be complete. LOGO! jumps back to output Q1.
SIEMENS
B01 If you still want to view your initial program, you can move the cursor through the program using the keys.
Q1
ESC OK
LOGO! 12/24 RC
>
However, we now leave the program entering step and return to the program menu ESC using the key. In order to be able to start the program, you must return to the main menu using the ESC key.
>
Using the keys, move the cursor to Start and confirm with the OK key.
ESC
OK
S1
=1
S2
=0
Q :0.,1.
1 23456789
0123456789 01234
=1 Q1
0123456
I :0.,1.,2.
123456789 0123456789 01234
ESC OK
LOGO!
SIEMENS Stop
LOGO! 12/24 RC
When the setting for the required block has been made, press the OK key. The cursor jumps to the first parameter to be modified. You can now modify the value using the keys.
SIEMENS
SIEMENS When the setting for the required value has been made, press the OK key. The cursor jumps to the block number. Using the keys, you can select the next block to be changed, and so on.
LOGO!
I :0.,1.,2.
123456789 0123456789 01234 LOGO!
ESC OK
Set Points (Par) Valores Actuales (RAM) Temporizadores (Timer) RE Remanencia - sin remanencia - con remanencia
1) LOGO! 2) LOGO!