Академический Документы
Профессиональный Документы
Культура Документы
Motorola/IBM PowerPC
603/603e BGA Target System
with HP E5346A High-Density
Termination Adapters
Solutions for
Product Note Digital System Debug
2
Passively Probing a This product note describes how to connect an HP logic analyzer to the
Motorola/IBM PowerPC BGA package of a Motorola/IBM PowerPC 603/603e target system for
603/603e BGA Target use with an inverse assembler.
System with HP E5346A
High-Density Termination Signals required for inverse assembly are shown in the pinout
Adapters information beginning on page 7 and must be routed to AMP Mictor 38
connectors for connection to the logic analyzer.
Eight, 16-channel logic analyzer pods are required for inverse assembly.
These eight pods are connected via the Mictor connectors to four
HP E5346A high-density termination adapters. The adapters are not
included with the inverse assembler and must be ordered separately.
J4
PPC 603
J3 J1
BGA Processor
J2
Top View J5
Direct Connection The HP E5346A high-density adapters use a minimal amount of board
through HP E5346A space. Each high-density adapter connects two logic analyzer pods,
High-Density Adapter providing 32 channels of logic analysis per connector and access to two
Cables clock pins, as shown in figure 2.
Probe cables
from logic
analyzer
Odd # probes
Labels*
+5VDC 1 2 SCL
GND DC 3 4 SDA
CLK 5 6 CLK
D15 7 8 D15
D14 9 10 D14
Label (both
D13 11 12 D13 Pin 1
D12 13 14 D12 sides)*
10 Pf bevel
D11 15 16 D11 HP E5346A
D10 17 18 D10 High-Density
D9 19 20 D9
250Ω
Termination
D8 21 22 D8 RCR
Adapter
D7 23 24 D7
D6 25 26 D6
D5 27 28 D5 90KΩ
D4 29 30 D4
D3 31 32 D3 Shroud
* A package of labels is provided so that you can use your own
D2 33 34 D2
conventions to keep track of cable connections. For more labels,
D1 35 36 D1
order HP part number 01650-94310
D0 37 38 D0
Mictor
connector
Figure 2. HP E5346A High-Density Termination Adapter
4
The AMP Mictor connector must be placed close enough to the target
system so that the stub length created is less than 1/5 the
Tr (bus risetime). For PC board material (er=4.9) and Zo in the range of
50-80Ω , use a propagation delay of 160 ps/inch of stub.
To To
Logic Target
90 K Ω
Analyzer System
GND
J4
PPC603
J3 J1
BGA Processor
J2
Top View J5
0.030 in
∅ 0.100 in 0.250 in
0.76 mm TYP
Mounting holes for 2.54 mm 6.35 mm
support shroud
0.996 in 0.329 in
0.276 in 8.36 mm
25.30 mm
7.01 mm
0.245 in
6.22 mm 0.400 in
10.16 mm
Mictor Connector Placing the AMP Mictor connectors as close as possible to the signal
Placement source will minimize stub length and ensure a reliable measurement.
Figure 4 shows the connector layout of J1-J5. J1-J4 are required for
inverse assembly, while J5 is optional for timing or state analysis of
I/O ports.
Mictor Connector The AMP Mictor connectors are available directly from AMP
(PN 2-767004-2) or from HP (PN E5346-68701). The HP Mictor kit con-
tains five AMP Mictor connectors and five support shrouds. The signals
+5 V DC, SCL, and SDA are not used for probing and should not be
connected to the target system, as shown in figure 2.
Inverse Assembler An inverse assembler translates logic levels captured by the logic
analyzer into PowerPC 603/603e mnemonics and identifies the micro-
processor bus cycles captured, such as memory read/write, interrupt
acknowledge, or I/O read/write.
For better visibility of the external bus, the instruction cache should be
disabled. If the instruction cache is enabled, many instructions are
executed from the cache and do not appear on the external bus.
6
0.450 in
11.44 mm
17.500 in 0.209 in
444.50 mm 5.31 mm
0.465 in
11.80 mm
0.271 in
6.89 mm
1.400 in
35.56 mm
2.393 in 1.100 in
60.77 mm 27.94 mm
Source Correlation The inverse assembler can be used with the HP B4620B source
Tool Set correlation tool set. This allows you to time-correlate an acquired trace
to written code. The source correlation tool set uses the information pro-
vided in your object file to build a database of source files, line numbers
and symbol information.
Pin-out Information on This table describes the connections for the four Mictor 38 connectors
Required Signals for necessary for compatibility with the inverse assembler and the
Inverse Assembly HP E5346A high-density termination adapter cables. This is intended to
be a guide for placing probing connectors on a target system.
For inverse assembly, the J1, J2, J3, and J4 connectors listed below must
be connected through the four high-density adapter cables. For simulta-
neous timing and state analysis for all signals, additional connectors must
be used.
J1 38 1 0 P01 A31(LSB)
36 1 J15 A30
34 2 M01 A29
32 3 H16 A28
30 4 K02 A27
28 5 G15 A26
26 6 K01 A25
24 7 G13 A24
22 8 F04 A23
20 9 F16 A22
18 10 H03 A21
16 11 F15 A20
14 12 J02 A19
12 13 F14 A18
10 14 J01 A17
8 15 F13 A16
6 CLK C09 SYSCLK
____________________________________________________________
J1 37 2 0 H02 A15
35 1 E16 A14
33 2 H01 A13
31 3 E15 A12
29 4 G02 A11
27 5 E13 A10
25 6 D04 A9
23 7 D16 A8
21 8 E02 A7
19 9 D15 A6
17 10 G01 A5
15 11 D14 A4
13 12 F02 A3
11 13 D13 A2
9 14 E04 A1
7 15 C16 A0(MSB)
5 CLK
8
J3 38 5 0 R04 DL31(LSB)
36 1 T03 DL30
34 2 P04 DL29
32 3 T02 DL28
30 4 T01 DL27
28 5 R03 DL26
26 6 N04 DL25
24 7 NO3 DL24
22 8 P03 DL23
20 9 T13 DL22
18 10 N12 DL21
16 11 P13 DL20
14 12 N10 DL19
12 13 T14 DL18
10 14 R14 DL17
8 15 R16 DL16
6 CLK
9
J4 37 8 0 R09 DH15
35 1 T10 DH14
33 2 N09 DH13
31 3 P09 DH12
29 4 R10 DH11
27 5 T11 DH10
25 6 T12 DH9
23 7 R11 DH8
21 8 N11 DH7
19 9 P11 DH6
17 10 R12 DH5
15 11 R13 DH4
13 12 T15 DH3
11 13 R15 DH2
9 14 T16 DH1
7 15 P14 DH0(MSB)
5 CLK
10
Warranty Information
These Hewlett-Packard products have a warranty against defects in
material and workmanship for a period of one year from date of ship-
ment. During this warranty period, Hewlett-Packard Company will, at
its option, either repair or replace products that prove to be defective.
For more information about the
HP 16600A and 16700A Series analysis
systems visit our web site,
http://www.hp.com/go/las-data
United States:
Hewlett-Packard Company
Test and Measurement Call Center
P.O. Box 4026
Englewood, CO 80155-4026
1 800 452 4844
Canada:
Hewlett-Packard Canada Ltd.
5150 Spectrum Way
Mississauga, Ontario
L4W 5G1
(905) 206 4725
Europe:
Hewlett-Packard
European Marketing Centre
P.O. Box 999
1180 AZ Amstelveen
The Netherlands
(31 20) 547 9900
Japan:
Hewlett-Packard Japan Ltd.
Measurement Assistance Center
9-1, Takakura-Cho, Hachioji-Shi,
Tokyo 192, Japan
Tel: (81-426) 56-7832
Fax: (81-426) 56-7840
Latin America:
Hewlett-Packard
Latin American Region Headquarters
5200 Blue Lagoon Drive
9th Floor
Miami, Florida 33126
U.S.A.
Tel: (305) 267 4245/4220
Fax: (305) 267 4288
Australia/New Zealand:
Hewlett-Packard Australia Ltd.
31-41 Joseph Street
Blackburn, Victoria 3130
Australia
Tel: 1 800 629 485 (Australia)
Tel: 0 800 738 378 (New Zealand)
Fax: (61 3) 9210 5489
Asia Pacific:
Hewlett-Packard Asia Pacific Ltd
17-21/F Shell Tower, Times Square,
1 Matheson Street, Causeway Bay,
Hong Kong
Tel: (852) 2599 7777
Fax: (852) 2506 9285