Академический Документы
Профессиональный Документы
Культура Документы
ISO 7053:1992
STANDARDS AUSTRALIA
1 The Crescent,
Homebush NSW 2140 Australia
STANDARDS NEW ZEALAND
Level 10, Standards House,
155 The Terrace,
Wellington 6001 New Zealand
ISBN 0 7337 0542 1
ii
PREFACE
This Standard was prepared by the Joint Standards Australia/Standards New Zealand Committee
ME/29 on Fasteners.
The objective of this Standard is to provide the dimensions and mechanical properties of a standard
range of heat-treated steel hexagon washer head tapping screws.
This Standard is identical with and has been reproduced from ISO 7053:1992, Hexagon washer head
tapping screws.
Statements expressed in mandatory terms in notes to text, tables and figures are deemed to be
requirements of this Standard.
As this Standard is reproduced from an International Standard, the following applies:
This is a free 7 page sample. Access the full version at http://infostore.saiglobal.com.
(a) Its number appears on the cover and title page while the International Standard number
appears only on the cover.
(b) In the source text, ‘this International Standard’ should read ‘this Australian/New Zealand
Standard’.
(c) A full point substitutes for a comma when referring to a decimal marker.
Reference to International Standards should be replaced by equivalent Australian, New Zealand or
Australian/New Zealand Standards, as follows:
Reference to International Standard Australian, New Zealand or Australian/New
Zealand Standard
ISO AS/NZS
1478 Tapping screws thread 4411 Tapping screws thread
2702 Heat-treated steel tapping 4412 Heat-treated steel tapping
screws —Mechanical properties screws —Mechanical properties
3269 Fasteners— Acceptance inspection —
AS
4042 Threaded components — Electroplated 1897 Electroplated coatings on threaded
coatings components (metric coarse series)
4759 Tolerance for fasteners
4759-1 Part 1: Bolts, screws and nuts with —
thread diameters ≥1.6 and ≤150 mm
and product grades A, B and C.
CONTENTS
Page
1 Scope . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. .. . .. .. .. 1
2 Normative references . . . . . . . . . . . . . . . . . . . . . . . . . . . .. .. ... .. .. 1
3 Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. .. .. . .. .. 2
4 Specifications and reference International Standards . . . . .. .. ... .. .. 4
5 Designation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. .. .. . .. .. 4
This is a free 7 page sample. Access the full version at http://infostore.saiglobal.com.
iv
NOTES
1
1 Scope
This International Standard specifies hexagon washer head tapping screws with threads from ST2,2 up to and
including ST8.
2 Normative references
The following standards contain provisions which, through reference in this text, constitute provisions of this
International Standard. At the time of publication, the editions indicated were valid. All standards are subject to
revision, and parties to agreements based on this International Standard are encouraged to investigate the
possibility of applying the most recent editions of the standards indicated below. Members of IEC and ISO
maintain registers of currently valid International Standards.
ISO 4759-1:1978, Tolerances for fasteners — Part 1: Bolts, screws and nuts with thread diameters between 1,6
(inclusive) and 150 mm (inclusive) and product grades A, B and C.
COPYRIGHT
This is a free preview. Purchase the entire publication at the link below: