Академический Документы
Профессиональный Документы
Культура Документы
1. Once you get the log file ,first check if all the route in the cluster has been covered,ifnot,the log is useless,tell the DT Teams to test again 2. If you are now using the logs for ATP report ,check if the time reached 4 hours.If not, the log is useless,tell the DT Teams to test again 3. When you are analysisingthe Log file ,make sure you have selected the right Log files,if the log file is not right ,all the KPI you get is useless.
4. In the bracket of the name of each KPI is the services we need the pictures.If there are many service ,it means all these servicess pictures is need 5. Some pictures and KPIs are together ,we can finish it at the same time to save our time. 6. The Threshold and the coloer must be the same as the picture. 7. Combine all the logs if there are many logs with the same service. Here shows how to Combine:
8. Log name: when you get a log ,the name of it may be very long ,so in the lengend it will be very long ,its not good to see ,such like follow:
So we need to change the log names like this: Cluster 6 -short call Cluster 7 HSDPA short call Its short and easy to see So please rename the log before analysising(if the log with 2 MS,copy 2 with different names)
Position
Services
check
Scanner
Long Call
EcIo Histogram EcIo-Graph TxPower Pilot Pollution Active Set Size Droped Call
Best Server RSCP RSCP-Histogram RSCP-Graph EcIo Short Call-to Mobile EcIo Histogram EcIo-Graph TxPower Pilot Pollution Active Set Size Droped Call Access Failures
Best Server RSCP RSCP-Histogram HSDPA Long RSCP-Graph EcIo EcIo Histogram EcIo-Graph TxPower
Pilot Pollution
Best Server RSCP RSCP-Histogram RSCP-Graph EcIo HSUPA Long EcIo Histogram EcIo-Graph TxPower Pilot Pollution
HSUPA Throughput
Droped Call
Best Server RSCP RSCP-Histogram RSCP-Graph EcIo EcIo Histogram EcIo-Graph Pilot Pollution
R99 PS
R99 Throughput DL
R99 Throughput UL
HS Short
Access Failures
Some other Notice: 1. In the picture, no need to show PSC\NodeB ID\Sector ID, just show the sites, and the site should be on the front layer. 2. In the picture ,the route should be full-screen,the cluster boundary \PreDT route should be shown on the map ,dont show other things. 3. The legend and the color should allow the pictures below. 4. The names of superscream should be like this: Cluster6-Long Call Cluster6-Short Call to Mobile Cluster6-Short Call to PSTN Cluster6-HSDPA Long Cluster6-HSUPA Long Clusetr6-R99 CLuset6-Scanner Cluster6-HS Short
KPIBest Server
Snapshot
Position
Position
KPIRSCP
Snapshot
Position
KPIRSCP -Histogram
Snapshot
RSCP Histogram
100%
80%
17.58%
10.71% 4.20%
Position
Methodfill the percentage into the Excel(only the GREEN colum) file which I send to you and then the graph will appear automaticly
KPI : RSCP-Graph
RSCP distribution
100% 80% 60% 40% 20% 0%
<-120.00 -120.00to-90.00 -90.00to-85.00 -85.00to-75.00 -75.00to-60.00 >-60
Position
Methodfill the percentage into the Excel(only the GREEN colum) file which I send to you and then the graph will appear automaticly
Position
KPIRSCP-Histogram
KPIRSCP-Graph
KPIEc/Io
Snapshot
Position
KPIEc/Io Histogram
For scanner may be different ask ZhuJin Snapshot:
Ec/No Histogram
100%
80%
60%
50.68%
2.45%
4.39%
Position
Methodfill the percentage into the Excel(only the GREEN colum) file which I send to you and then the graph will appear automaticly
Position
Methodfill the percentage into the Excel(only the GREEN colum) file which I send to you and then the graph will appear automaticly
Position
KPIEc/Io-Histogram
KPIEc/Io-Graph
KPITxPower
Snapshot
Position
KPIPilot Pollution
Snapshot
Position
Position
KPIHSDPA Throughtput
Snapshot
Position
KPIR99 Throughtput DL
Snapshot
Position
KPIHSUPA Throughtput
Snapshot
Position
KPIR99 Throughtput UL
Snapshot
Position
KPIHSDPA CQIDL
Snapshot
Position
KPIAccess Failures
Snapshot
Position
KPIDroped Call
Snapshot
Position
Belows
report
Total
List
Part 9
Type of Call Actu Information Element Mod e Total attempts al valu e
CSV Access Failure Rate 1-MS 2 *Voice Call Setup time (Mobile to Mobile) Setup -A CS Setup Calls Setup -A CS Setup Calls
Devi ce
Accept ance
Comm ents
<1.0%
Yes
Setup -B
PS Setup Calls PS Setup Calls PS Setup Calls 210 Yes 1.0 % Yes 1.0 % Yes
PSD Drop Rate PSD R99 Average DL throughput PS DL/UL 1-MS 3 (kbps) Loaded PSD R99 Average UL throughput (kbps)Loaded
Setup -B
Setup -B
Setup -B
95th percentile PSD Call Setup time Setup -B PS Setup Calls seconds Voice Short( to PSTN ) 2-MS 1 sessions 3 Yes
*Voice Call Setup time (Mobile to PSTN) HSUPA Average UL Throughput Setup -B (kbps) for UE category 3 under load Setup -A
CS Setup Calls
HSUP A Long
2-MS 2
Time XXXmin s Setup -A Time XXXmin s 95th percentile of <1.0% Yes 1.0 %
Voice Long
Yes
Soft/Softer Handover Overhead HSDPA Average DL Throughput HSDP A Long 3-MS 2 (kbps) for UE category 8 under load
Setup -A
<1.6
Yes
Setup -B
> 2 Mbps
Yes
HSDPA Drop Rate HSDPA Access Failure HS Short 4-MS 2 Rate HSUPA Access Failure Rate
Setup -B Setup -B
1.0 %
Yes
1.0 %
Yes
Setup -B
1.0 %
Yes
Part 10
Accep Devi ce Type of Call Actu Information Element Mod e Total attempts al valu e t Limit( As Per SOW) (%)
95th HSDPA Latency-Statio nary 5-DC1 percenti HSPA Ping 1000 0 le session s 100 ms Stationary Maximum UL 5-DC 1 HSU PA Long HSUPA Bit Rate (kbps) under no load (UE Category 3) Stationary HSD PA Long Maximum DL HSDPA Bit Rate (kbps) under no load HSDPA Long N/A >6 Mbps Yes HSUPA Long N/A > 1.2 Mbps Yes Yes
Accepta nce
Comments
HSPA Ping
Yes
percenti 5-DC 2 PS Ping PSD Latency 5-DC2 PS Ping 1000 0 le session s 100 ms Yes
Part 11
Accep Devi ce Type of Call Actu Information Element Mod e Total attempts al valu e
Setup OK + Setup Fail Call CSV Drop Rate Setup -A Complete Time +Drop Time / Yes / Yes
Setup -A
Description: CSV Access Failure= CS Failed Setups / CS Call Setups *100% Example: CSV Access Failure = 1/7 *100% = 14.28%
KPI*Voice Call Setup time (Mobile to Mobile)From Short Call Mobile to Moble
Position:
Description: From RRCConnectionReq to Alerting Example: In the picture ,the percent of the time less than 9s is 100%
Description: HSDPA Access Failure= PS Failed Setups / PS Call Setups *100% Example: HSDPA Access Failure = 0/12 *100% = 0%
Decription PSD Drop Rate = PS Dropped Calls / PS Successful Calls *100% Example In this picture, PSD Drop Rate = 0/9*100% =0%
Description:
Example:
Description: From RRCConnectionReq to PDPActive Complete Example: In this picture,the percent of time less than 3s is 99.4%
KPI Voice Call Setup time (Mobile to PSTN)From Short Call (Mobile to PSTN)
Position:
Description: From RRCConnectionReq to Alerting Example: In the picture ,the percent of time less than 5s is 98.8%
Position:
Description: Drop times= 1 The lasting time: from 15:05 to 16:55 ,its totally 111 minutes. (make sure the time is coutinuous, if not ,we need to minus the time it inturrupt) The HSUPA Drop Rate = Drop times /The lasting time(minute)*1.5 Example: The HSUPA Drop Rate = 1/111*1.5 = 1.35%
Description: Drop times= 2 The lasting time: from 15:05 to 16:55 ,its totally 111 minutes. (make sure the time is coutinuous, if not ,we need to minus the time it inturrupt) The CSV Drop Rate = Drop times /The lasting time(minute)*1.5 Example: The CSV Drop Rate = 2/111*1.5 = 2.7%
Description: The BLER which below 2 percent Example: In the picture ,the CSV Quality(DL) = 95%
Longcall
Description:
Example: 2838*1:(2838 means the point nums of 1 pilot, 1 means that are 1 pilot in the ActiveSet) 217*2 : (217 means the point nums of 2 pilot, 2 meast that are 2 pilots in the ActiveSet) 19*3(19 means the point nums of 3 pilot, 3 meast that are 3 pilots in the ActiveSet) The Soft/Softer Handover Overhead = (2838*1+217*2+19*3)/(2838+217+19) = 1.115
Description: Drop times= 1 The lasting time: from 15:05 to 16:55 ,its totally 111 minutes. (make sure the time is coutinuous, if not ,we need to minus the time it inturrupt) The HSDPA Drop Rate = Drop times /The lasting time(minute)*1.5 Example: The HSDPA Drop Rate = 1/111*1.5 = 1.35%
Description: HSDPA Access Failure= PS Failed Setups / PS Call Setups *100% Example: HSDPA Access Failure = 0/12 *100% = 0%
KPIHSUPA Access Failure RateFrom HS Short callIts the same as HSDPA Access Failure Rate
Position:
Description: HSUPA Access Failure= PS Failed Setups / PS Call Setups *100% Example: HSUPA Access Failure = 0/12 *100% = 0%
KPIHSDPA Latency-Stationary
Positon:
Description Example:
KPIStationary Maximum UL HSUPA Bit Rate (kbps) under no load (UE Category 3)
Position: 1
KPIStationary Maximum DL HSDPA Bit Rate (kbps) under no load (UE Category 8)
Position:
KPIPSD Latency
Positon:
Description: CSV Access Failure Rate = Setup Fail / (Setup OK + Setup Fail) *100% Example: In the picture: CSV Access Failure Rate = 7 / (214 + 7) *100% = 3.2%
Description: CSV Drop Call Rate = Call Dropped / (Call Complete + Call Dropped)*100% Example: In this picture,its
2/(208+2) = 0.95%
PS-HSDPA Call
PS-HSUPA Call
Success
Accessibility 100.00 % 100.00 % 100.00 % 100.00 % 100.00 % 100.00 % 100.00 % 100.00 % 100.00 % 100.00 % 100.00 % 100.00 %
Retainability 0.00 % 0.00 % 0.00 % 0.00 % 1.38 % 0.00 % 0.00 % 0.00 % 0.00 %
SoftHandover Rate(%)
Ratio of Drop(%)
Ratio of Drop(%)
1453 1 100.00 %
KPI_CL35_CL32_CL7 .xls
Cluster 6 KPI Ratio of successful RRC connection establishment(%) Ratio of successful CS RAB establishment(%) Ratio of successful PS RAB establishment(HSDPA)(%)
100.00 % 100.00 %
Ratio of successful PS RAB establishment(HSUPA)(%) Ratio of CS-Speech Call Drop(%) Ratio of Drop(%) PS-HSDPA Call Ratio of Drop(%) PS-HSUPA Call
SoftHandover Rate(%)
Success Cell Inter-RAT CS Outgoing Handover Success Rate(WCDMA->GSM)(%) UL Block Error Rate(%)
RNCID 36 36 36 36 36
Exist Interference No No No No No
Maximum Average Minimum Cell Freq Cell Freq Cell Frep RTWP(dbm) RTWP(dbm) RTWP(dbm) -86.2 -63.7 -79.2 -81.2 -85.3 -106.516 -106.3173 -106.4029 -106.5058 -106.5548 -106.8 -112 -106.6 -106.8 -106.7
KPI_CL35_CL32_CL7 .xls
Reason
Action Taken
Problem Solved