Академический Документы
Профессиональный Документы
Культура Документы
1 Identification of substance:
Product details: Trade name: Purgasol Application of the substance / the preparation: Industrial cleaner Solvent for various applications Surface cleaning Manufacturer / Supplier: IBS Scherer GmbH Gewerbegebiet D-55599 Gau-Bickelheim Informing department: Labor Emergency information: Next toxicological information centre or for Germany: Beratungsstelle fr Vergiftungserscheinungen Mainz (Poison Information Center) Phone: +49 6131 / 19 24 0 Tel.: +49 (0) 6701 / 9383-0 Fax: +49 (0) 6701 / 9383-33
E-mail address of the competent person responsible for the Safety Data Sheet: info@ibs-scherer.de
2 Hazards identification
Hazard designation: Xn Harmful Information pertaining to particular dangers for man and environment Vapours of the product are heavier than air and may accumulate on the ground, in mines, drains or cellars with higher concentration. In the gas volume of sealed packages vapours of flammable solvents, especially at action of heat, may accumulate. Keep away fire and ignition sources. Long or repeated contact with skin may cause dermatitis due to the degreasing effect of the solvent. R 65 Harmful: may cause lung damage if swallowed. R 66 Repeated exposure may cause skin dryness or cracking. *
3 Composition/information on ingredients
Chemical characterization Description: Cleansing agent Dangerous components: Naphtha (petroleum), hydrotreated heavy CAS: 64742-48-9 EINECS: 265-150-3 Index number: 649-327-00-6 Additional information Content of benzene: < 0.1 % (percentage by weight)
Xn; R 65-66
> 90%
DR
Page 2/6
Revision: 06.05.2009
Personal protection for the person providing first aid. After inhalation: Supply fresh air. If required, provide artificial respiration. Keep patient warm. Consult doctor if symptoms persist. In case of unconsciousness bring patient into stable side position for transport. After skin contact: Wash with soap and water. After prolonged skin contact defatting of skin possible, use skin protecting agent after prolonged skin contact. If skin irritation continues, consult a doctor. After eye contact: Rinse opened eye for several minutes under running water. If symptoms persist, consult doctor. After swallowing: Rinse out mouth and then drink plenty of water. Do not induce vomiting! Call a doctor immediately. Information for doctor: Danger: Danger of pneumonia.
DR
Page 3/6
Revision: 06.05.2009
DR
Page 4/6
Revision: 06.05.2009
To avoid skin problems reduce the wearing of gloves to the required minimum. Material of gloves Polychloroprene Recommended thickness of the material: = 5 mm Maximum penetration time 4 h Nitrile rubber - NBR Recommended thickness of the material: 0.4 mm Fluorocarbon rubber (Viton) - FKM Recommended thickness of the material: 0.4 mm The selection of the suitable gloves does not only depend on the material, but also on further marks of quality and varies from manufacturer to manufacturer. Penetration time of glove material Penetration time: 8 hours The exact break through time has to be found out by the manufacturer of the protective gloves and has to be observed. Protective gloves should be replaced at first signs of wear. Eye protection: Safety glasses recommended during refilling. Body protection: Solvent resistant protective clothing Protective clothing should be selected specifically for the working place.
Change in condition Boiling point/Boiling range: 180 - 240C Setting temperature / range: -50C Flash point: Ignition temperature: Danger of explosion: > 60C ~ 230C Product is not explosive. However, formation of explosive air/vapour mixtures is possible.
Critical values for explosion: 0.6 Vol % Lower: 6.0 Vol % Upper: Vapour pressure at 20C: Density at 20C Vapour density (AIR = 1): Evaporation rate 2.3 kPa 0.77 g/cm > 1 / 101 kPa (Air=1) 212 (DIN 53170)
Solubility in / Miscibility with Not miscible or difficult to mix Water: pH-value: Viscosity: kinematic at 20C: not applicable 1.736 mm/s
(Contd. on page 5)
GB
DR
Page 5/6
Revision: 06.05.2009
Additional information
11 Toxicological information
Acute toxicity: LD/LC50 values that are relevant for classification: no data available Primary irritant effect: on the skin: Long or repeated contact can defat skin and may cause dermatitis. on the eye: Weak irritating effect Sensitization: No sensitizing effect known. Additional toxicological information: Inhalation of concentrated vapours as well as oral intake will lead to anaesthesia-like conditions and headache, dizziness, etc.
12 Ecological information:
Information about elimination (persistence and degradability): Other information: no data available Behaviour in environmental systems: Mobility and bioaccumulation potential: The product is lighter than water. General notes: Water hazard class 1 (Self-assessment): slightly hazardous for water
13 Disposal considerations
Product: Recommendation Disposal must be made according to official regulations. Contact manufacturer for recycling information. European waste catalogue: 14 06 03 other solvents and solvent mixtures
14 Transport information
Land transport ADR/RID (cross-border): ADR/RID Class: (Contd. on page 6)
GB
DR
Page 6/6
Revision: 06.05.2009
Maritime transport IMDG-Code: IMDG Class: Air transport ICAO-TI and IATA-DGR: ICAO/IATA Class: Transport/Additional information: Not dangerous according to the above specifications. *
15 Regulatory information
Designation according to EC guidelines: The product has been classified/labelled in accordance with EC Directives / relevant national laws. Code letter and hazard designation of product: Xn Harmful
Hazard-determining components of labelling: Distillates (petroleum), hydrotreated light Risk phrases: 65 Harmful: may cause lung damage if swallowed. 66 Repeated exposure may cause skin dryness or cracking. Safety phrases: 23 Do not breathe fumes/aerosol. 24 Avoid contact with skin. 62 If swallowed, do not induce vomiting: seek medical advice immediately and show this container or label. National regulations Information about limitation of use: Employment restrictions concerning young persons must be observed. Decree to be applied in case of technical fault: Water hazard class: Water hazard class 1 (Self-assessment): slightly hazardous for water
16 Other information:
These data are based on our present knowledge. However, they shall not constitute a guarantee for any specific product features and shall not establish a legally valid contractual relationship. Reasons for changes: The Material Safety Data Sheet has been revised. Changes in the respective chapters are characterized in the left side edge by *. Relevant R-phrases: 65 Harmful: may cause lung damage if swallowed. 66 Repeated exposure may cause skin dryness or cracking. Recommended restriction of use: Industrial use * Data compared to the previous version altered.
GB
DR