Академический Документы
Профессиональный Документы
Культура Документы
March 9, 2009
Contents
Chapter 1 Summarize
1.1. Introduction to Certification Outline
This certification outline is compiled by WiMAX Network Planning & optimization Department, ZTE Corporation. The outline includes the standards for certifying the network planning and optimization skills on ZTE WIMAX products which are used by customers and third-parties. This outline can also serve as the basis for the design of the training courses, textbooks and test questions for the certification on skills demanded by network planning and optimization on ZTE WIMAX products.
Level
(Elementa ry Level)
Staff: Have at least one and a half years of practical experience in network planning and optimization; Optional: Have 35 years of practical experience in the related field; Optional: Have the competency of an engineer in
Certification Document of ZTE Skill Center Correspondin g Post Competency and Qualification communication system for at least two years. Have at least 35 years of practical experience in network planning and optimization; have 3 or more technical articles published in internal or external The ability of optimization and planning and negotiation of a city or nation publications; Optional: Have more than 5 years of practical experience in the related field; Optional: Have the competency of an engineer in communication system for more than 5 years.
Skill Level
Applicable Scope
Skill Requirement
Required Training
Level
(High Level)
The Optimization and planning optimization of province or nation level manager of city or nation
of
The test focuses on examining the understanding on related theories. Altogether there are 60 test questions involving Single Choice, Multiple Choice and Judgment types. Level-I ZTE Employee Judgment Gap Filling 20 20 20 (1Score/Ques. 0 (2 Score/Ques.) (2 Score/Ques.) ) Certification contents and percentage of each tested knowledge point
Percentage of Test Questions for ZTE Employees 10 Percentage of Test Questions for Outsourcing Parties 10
Single Choice
Multiple Choice
Brief Answer 0
I D 1
Knowledge Points Detail 1.1 Wireless Introduction 1.1.1 Wireless Network Topologies 1.1.2 Wireless Technologies 1.1.3 Kinds of Wireless Networks 1.1.4 Wireless Broadband Access (WBA) 1.2 Related Organization 1.2.1 IEEE 1.2.2 WiMAX Forum 1.3 What is WiMAX 1.3.1 What is WiMAX 1.3.2 What is 802.16d 1.3.3 What is 802.16e 1.3.4 WiMax Speed and Range 1.3.5 Why WiMAX1 1.3.6 WiMAX Goals 1.4 Salient Features of WiMAX 1.4.1 OFDM-based physical layer 1.4.2 Very High Peak Date Rate 1.4.3 Scalable bandwidth and rate support 1.4.4 Adaptive modulation and coding (AMC) 1.4.5 Link-layer
Certification Document of ZTE Skill Center Percentage of Test Questions for ZTE Employees Percentage of Test Questions for Outsourcing Parties Percentage of Test Questions for Customers
I D
Knowledge Points Detail retransmissions 1.4.6 Support for TDD and FDD 1.4.7 Orthogonal frequency division multiple access (OFDMA) 1.4.8 Flexible and dynamic per user resource allocation 1.4.9 Support for advanced antenna techniques 1.4.10 Qulity of service support 1.4.11 Robust security 1.4.12 Support for mobility 1.4.13 IP-based architecture Section2 OFDM 2.1 OFDM System Description 2.2 OFDM Orthogonality 2.3 How to Overcome Inter Symbol Interference (ISI) 2.4 How to Overcome Inter Carrier Interference (ICI) Section3 OFDMA 3.1 OFDMA Basics 3.2 OFDMA Symbol Structure and SubChannelization 3.3 Scalable OFDMA 3.4 TDD Frame Structure 3.5 Other Advanced PHY Layer Features 3.6 Difference between OFDMA and OFDM Section4 WiMAX MAC 4.1 Common MAC Concepts 4.1.1 CS Sublayer 4.1.2 MAC CPS Sublayer 4.2 Quality of Service (QoS) Support 4.3 MAC Scheduling Service 4.4 Mobility Management 4.4.1 Power Management 4.4.2 Handoff 4.5 Security Section5 WiMAX Advanced Features 5.1 Smart Antenna Technologies 5.2 Fractional Frequency Reuse 5.3 Multicast and Broadcast Service (MBS) Section6 WiMAX Network Architecture
Certification Document of ZTE Skill Center Percentage of Test Questions for ZTE Employees Percentage of Test Questions for Outsourcing Parties Percentage of Test Questions for Customers
I D
Knowledge Points Detail Section7 WiMAX Channel Estimation 7.1 Introduction 7.2 Channel Estimation 7.2.1 Transmitter 7.2.2 Channel 7.2.3 Reciever Section8 WiMAX Major Benefits Section1 Overview and Process of Wireless Network Planning 1.1 Definition of Wireless Network Planning 1.2 Objectives of WiMAX Network Planning 1.3 Process of WiMAX Wireless Network Planning Section2 Network Dimensioning and Design 2.1 Requirements 2.2 WiMAX Cell Site Design 2.3 WiMAX Networks Dimensioning 2.3.1 Deployment Scenarios 2.3.2 Dimensioning Process 2.4 Business Plan, Assets, and Key Performance Indicators 2.5 Strategy 2.6 Coverage Dimensioning 2.7 Capacity Dimensioning 2.8 Joint Dimensioning Section3 Radio Propagation models 3.1 Free-Space Model 3.2 SUI Model 3.3 Standard Macrocell Propagation Model Section4 WiMAX Coverage Planning 4.1 Overview of Link Budget 4.2 Physical Layer Parameters Meanings of PUSC in WiMAX 4.2.1 Link Budget of the WiMAX System 4.2.2 Overview of WiMAX Link Budget 4.3 Input and Output 4.3.1 Input Parameters 4.3.2 Compulsory Input Parameters 4.3.3 Default Parameters 4.4 Link Budget Table Section5 WiMAX Capacity Planning
45
45
45
Certification Document of ZTE Skill Center Percentage of Test Questions for ZTE Employees Percentage of Test Questions for Outsourcing Parties Percentage of Test Questions for Customers
I D
Knowledge Points Detail 5.1 Principles of Subscriber Predication 5.1.1 Methods of Subscriber Predication 5.2 Service Models 5.2.1 Voice Service Model 5.2.2 Data Service Model 5.3 WiMAX Capacity Planning 5.3.1 Physical Layer Traffic Calculation of Downlink Subframe 5.3.2 Physical Layer Traffic Calculation of Uplink Subframe 5.3.3 Summary of Traffic Calculation Section6 Detailed Calculation of Estimated Site Number 6.1 Site Number Estimation Based on Coverage Requirement 6.2 Site Number Estimation Based on Traffic Requirement Section7 Site Survey and Planning 7.1 Overview 7.2 Introduction to Site Survey 7.3 Available Site Survey and Selection 7.3.1 No Obvious Blocking Objects around the Site 7.3.2 Site Height 7.3.3 No Interference with Other Systems 7.4 Planned Site Survey and Selection 7.4.1 No Obvious Blocking Objects around the Site 7.4.2 Site Height 7.4.3 Distance between Site Location and Planned Site Location 7.5 Ultra-Wide Coverage Site Survey and Selection Section8 Antenna Selection 8.1 Overview 8.2 Antenna Selection 8.2.1 Frequency Range and Polarization Mode 8.2.2 Radiation Pattern, Horizontal BW, Vertical BW, and Gain 8.2.3 Downtilt Mode 8.2.4 Side Lobe Suppression and Null Fill 8.2.5 Front-to-back Ratio, Maximum Input Power,
Certification Document of ZTE Skill Center Percentage of Test Questions for ZTE Employees Percentage of Test Questions for Outsourcing Parties Percentage of Test Questions for Customers
I D
Knowledge Points Detail Third-order Intermodulation, Isolation 8.3 Selecting Antennas for Indoor Distribution Systems Section9 WiMAX Preamble & Neighbor Planning 9.1 Overview 9.2 Preamble & Neighbor Planning Flow 9.2.1 Preamble Planning Flow 9.2.2 Neighbor Planning Flow 9.3 Preamble Planning Procedure 9.4 Neighbor Planning via CNO 9.4.1 Neighbor Planning 9.4.2 Tips Section10 Tools Section1 Wireless Network Planning and Optimization Process 1.1 Basic Process Introduction 1.2 Requirement Analysis 1.3 Spectrum Scan 1.3.1 Scanning overview 1.3.2 Scanning test type and test tools 1.3.2.1 Test type 1.3.2.2 Test tools 1.3.2.3 Spectrum analyzer parameters setting 1.3.3 Test procedure 1.3.3.1 Drive test procedure 1.3.3.2 Fixed location test procedure 1.3.4 Analysis of test data 1.3.4.1 Analysis of drive test data 1.3.4.2 Analysis of fixed location test data 1.3.5 Analysis of interference in service areas 1.3.5.1 The influence of external interference 1.3.5.2 The influence of external interference on coverage 1.3.5.3 According to the result of frequency scanning export conclusions and scanning report. 1.3.6 System OMC uplink spectrum scanning instruction 1.3.6.1 Overview
37
37
37
Certification Document of ZTE Skill Center Percentage of Test Questions for ZTE Employees Percentage of Test Questions for Outsourcing Parties Percentage of Test Questions for Customers
I D
Knowledge Points Detail 1.3.6.2 Uplink spectrum scanning function 1.4 Single Station Test 1.4.1 Single station test scope and objective 1.4.2 Single station test verification requirement 1.4.2.1 Single site verification RNP 1.4.2.2 Coverage area verification 1.4.2.3 Coverage area KPI target 1.4.3 Single station test verification contents 1.4.3.1 Single site information verification 1.4.3.2 Functional test verification 1.4.3.3 Drive test result 1.4.4 Coverage test verification contents 1.4.4.1 Configuration information 1.4.4.2 Coverage polygon 1.4.4.3 Coverage street information 1.4.5 Single station and coverage test verification report 1.5 Calibration Test 1.6 Network Evaluation before Optimization 1.7 BS Cluster Optimization 1.8 Whole Network Optimization and Network Evaluation 1.9 Project Acceptance Test and Report Hand in Section2 Network Planning Issue 2.1 Optimization Test Tool Introduction 2.1.1 Optimization test tool CNT introduction 2.1.1.1 Overview 2.1.1.2 The use of ZXPOS CNT1 2.1.1.2.1 Test process 2.1.1.2.2 Hardware detection and configuration 2.1.1.2.3 Hardware configuration interface introduced 2.1.1.2.4 Hardware configuration interface introduced 2.1.1.3 Work interface 2.1.1.4 Window interface 2.1.1.4.1 Title bar
Certification Document of ZTE Skill Center Percentage of Test Questions for ZTE Employees Percentage of Test Questions for Outsourcing Parties Percentage of Test Questions for Customers
I D
Knowledge Points Detail 2.1.1.4.2 Menu bar 2.1.1.4.3 Status bar 2.1.1.5 Toolbar 2.1.1.6 Replay toolbar 2.1.1.7 Right key menu toolbar 2.1.1.8 Menu and function analysis 2.1.1.9 Explorer window 2.1.1.9.1 Device Config 2.1.1.9.2 Windows 2.1.1.10 Refresh rate to adjust the window style and the curve 2.1.1.10.1 Adjust wireless parameters window refresh rate chart 2.1.1.10.2 Style curve adjustment 2.1.1.11 Test software projects 2.1.1.12 Export of test data 2.1.1.12.1 Export pages 2.1.1.13 Subsection of test data 2.1.1.14 Route map 2.1.1.14.1 Toolbar introduction 2.1.1.14.2 Control Layer 2.1.1.14.3 Theme setting 2.1.1.14.4 Map parameters setting 2.1.1.14.5 Custom label settings 2.1.1.14.6 Marker parameters 2.1.1.14.7 Find the base station 2.1.1.15 Information display and switch 2.1.1.15.1 Values (WiMAX) 2.1.1.15.2 Information 2.1.1.15.3 Legend 2.1.1.16 Drive test map 2.1.1.17 Data test 2.1.1.17.1 Plans setting page automatic test plan 2.1.1.17.2 Message Test page news shows 2.1.1.17.3 Throughput shows the throughput of the page 2.1.1.17.4 Statistics show page 2.1.1.18 Data Monitor 2.1.1.19 WiMAX Logon Tool 2.1.1.20 WiMAX Logon Tool 2.1.1.21 WiMAX Communication Info
Certification Document of ZTE Skill Center Percentage of Test Questions for ZTE Employees Percentage of Test Questions for Outsourcing Parties Percentage of Test Questions for Customers
I D
Knowledge Points Detail 2.1.1.22 WiMAX Air Interface Message 2.1.1.23 WiMAX Modulation Statistics 2.1.1.24 WiMAX Date Throughput 2.1.2 Optimization analysis tool CNA introduction 2.1.2.1 Introduction 2.1.2.2 Terms, definitions and abbreviations 2.1.2.3 Comprehensive description 2.1.2.3.1 Background 2.1.2.3.2 Product Overview 2.1.2.4 Specific functions description 2.1.2.4.1 Basic function analysis 2.1.2.4.2 Segment'RSSI and Segment'CINR functions 2.1.2.4.3 Call event analysis and delay statistics 2.1.2.4.4 Analysis of handover events 2.1.2.4.5 Interference Analysis 2.1.2.4.6 Analysis of dropped calls 2.1.2.4.7 Calls, handover of the incident shows the geographical 2.1.2.4.8 Jitter Analysis of packet loss rate 2.1.2.4.9 Table part of the meaning of Item Value 2.2 Optimize Test 2.2.1 Test Content 2.2.1.1 Cover Test 2.2.1.2 Throughout Test 2.2.1.3 Cut-over Test 2.2.1.4 Calling Test 2.2.1.5 Operation Test 2.2.1.6 Handoff 2.2.1.7 Lose Words Rate 2.2.2 Testing Method 2.2.2.1 DT Testing 2.2.2.2 CQT Testing 2.3 RF Optimizing Subject 2.3.1 RF Optimizing Goal 2.3.2 Antenna Optimization 2.3.3 Calibration Power Optimizing 2.3.4 Interferences Searching and Frequency Scanning 2.4 Access and Paging
Certification Document of ZTE Skill Center Percentage of Test Questions for ZTE Employees Percentage of Test Questions for Outsourcing Parties Percentage of Test Questions for Customers
I D
Knowledge Points Detail 2.4.1 Basic connection flow 2.4.1.1 Connection flow chart 2.4.1.2 Small area option and downlink synchronization 2.4.1.2.1 OMC parameters chart below 2.4.1.2.2 Physicalal Layer Parameter OMC Configuration 2.4.1.3 Ranging 2.4.1.3.1 Ranging parameters 2.4.1.3.2 Ranging OMC parameter configuration 2.4.1.4 SBC negotiation ability 2.4.1.4.1 SBC parameters 2.4.1.4.2 SBC OMC parameters configuration 2.4.1.5 Coding and authorization 2.4.1.5.1 OMC parameters configuration 2.4.1.6 REG ability negotiation 2.4.1.7 Service flow setup 2.4.1.8 Obtaining IP 2.4.2 Idle Idle model and paging flow 2.4.2.1 The function of idle model 2.4.2.2 Paging chart 2.4.2.3 Entering idle flow chart 2.4.2.4 Location update 2.4.2.5 Paging flow 2.4.2.6 Exit idel state flow 2.4.2.6.1 OMC parameters configuration 2.5 Handover Technology 2.5.1 Handover types 2.5.1.1 Hard Handover (HHO) 2.5.1.2 Fast BS Switching (FBSS) 2.5.1.3 Macro Diversity HandoverMDHO 2.5.2 HHO workflow 2.5.3 The related parameters configure of HO 2.5.3.1 HO configure page 2.5.3.2 HO parameter instruction 2.5.3.3 Neighbor configure page 2.5.3.4 Neighbor parameters explan 2.5.3.5 Trigger configure
Certification Document of ZTE Skill Center Percentage of Test Questions for ZTE Employees Percentage of Test Questions for Outsourcing Parties Percentage of Test Questions for Customers
I D
Knowledge Points Detail 2.5.3.6 Trigger parameter instruction 2.6 Power Control optimization 2.6.1 PC and AMC principle 2.6.1.1 The purpose of PC 2.6.1.2 The principles of PC 2.6.1.3 Power Control Classification 2.6.1.4 AMC 2.6.1.5 PC and AMC arithmetic 2.6.2 Power Control and AMC configure 2.6.2.1 DL Burst Profile configure 2.6.2.2 DL Burst Profile parameters instruction 2.6.2.3 UL Burst Profile configure 2.6.2.4 UL Burst Profile parameter instruction 2.6.2.5 AMC configure 2.6.2.6 AMC frequent parameters instructions 2.6.2.7 PC configure parameters 2.6.2.8 PC parameters explanation 2.7 Admission and congestion control 2.7.1 QOS of the airinterface resource of WiMAX 2.7.1.1 Air-interface resource 2.7.1.2 Flux of subscribers service-flow 2.7.1.3 Types of serviceflow 2.7.1.4 Admission and congestion control 2.7.2 Admission Control 2.7.2.1 Basic principle 2.7.2.2 Realization method 2.7.2.3 The application scene of admission control 2.7.2.4 Serveral terms considering by admission control 2.7.2.5 Admission control parameters explanation 2.7.2.6 Admission configure page 2.7.3 Congestion control 2.7.3.1 Basic principle 2.7.3.2 Realized mode 2.7.3.3 The scene of congestion control 2.7.3.4 Congestion control
Certification Document of ZTE Skill Center Percentage of Test Questions for ZTE Employees Percentage of Test Questions for Outsourcing Parties Percentage of Test Questions for Customers
I D
Knowledge Points Detail parameter 2.7.3.5 Congestion control configure page Section3 WiMAX Terminal Introduction 3.1 Summary of frequent terminal sort summary 3.1.1 Sort according to the shape and interface 3.1.2 Sort according to the chip vendor 3.2 Detail configuration instruction of frequent terminal 3.2.1 USI CPE terminal 3.2.1.1 Configuration parameters operation instruction 3.2.1.2 Use command 3.2.2 ZTE terminal (base on Beceem chip) 3.2.2.1 Configuration parameters operation instruction 3.2.2.2 TTIS authentication configuration 3.2.3 GCT terminal 3.2.3.1 Configuration parameters operation instruction 3.2.3.2 Common command instruction 3.2.3.2.1 Set frequency 3.2.3.2.2 Print packet command 3.2.3.2.3 Dump command 3.2.3.2.4 Configuration command Section4 WiMAX Network KPI Introduction 4.1 WiMAX network performance KPI introduction 4.1.1 KPI concept 4.1.2 WiMAX KPI introduce 4.1.2.1 Coverage KPI 4.1.2.1.1 DL/UL RSSI 4.1.2.1.2 DL/UL CINR 4.1.2.1.2 DL/UL Tx Power 4.1.2.2 System Performance KPI 4.1.2.2.1 Initial Access 4.1.2.2.2 Service Flow Setup 4.1.2.2.3 System Connection Drop Rate 4.1.2.2.4 Hard Handover 4.1.2.2.5 Delay 4.1.2.2.6 Jitter 4.1.2.2.7 Packet Loss 4.1.2.3 KPI recommend value
Certification Document of ZTE Skill Center Percentage of Test Questions for ZTE Employees Percentage of Test Questions for Outsourcing Parties Percentage of Test Questions for Customers
I D
Knowledge Points Detail 4.2 KPI statistic tool CNO2 introduction 4.2.1 Introduction of CNO24.2.2 Benefit of using CNO2 4.2.3 Data Characteristic of CNO2 4.2.4 Advantage of CNO2 4.2.5 Main Operation Statistic steps of CNO2 for WiMAX
8 Section1 Network Simulation Introduction 1.1 Overview of network simulation 1.2 Network Simulation basics 1.2.1 Digital Map 1.2.2 Universal Transverse Mercator (UTM) 1.3 Wireless Propagation Scenarios Definition 1.4 Model Selection Section2 Propagation Model Tuning 2.1 Data Collection 2.2 Data Processing 2.3 Data Analysis 2.4 Assessment Precision Section3 Simulation Flow 3.1 Data Preparation 3.2 Path Loss Prediction 3.3 Traffic Distribution Creation 3.4 Wireless Network Simulation Analysis 3.5 Outputting Network Simulation Design Report Section4 Quality Assessment on Wireless Network Simulation Design 4.1 Acquiring Network Performance Data 4.2 Comparison Analysis 4.3 Deduction on Network Simulation Quality Section5 Simulation in Network Planning and Optimization 5.1 Network Topology Design 5.2 Network KPI Prediction 5.3 Capacity Expansion and Coverage Issue Section6 Static Simulation Algorithm 6.1 Effective Site Antenna Height Calculation Methods 6.2 Diffraction Loss Calculation (Knife Edge)
Certification Document of ZTE Skill Center Percentage of Test Questions for ZTE Employees Percentage of Test Questions for Outsourcing Parties Percentage of Test Questions for Customers
I D
20 20 10 10 (1Score/Ques (2Score/Ques (1Score/Ques (2Score/Ques .) .) .) .) Certification contents and percentage of each tested knowledge point
Percentage of Test Questions for ZTE Employees 10 Percentage of Test Questions for Outsourcing Parties 10
I D 1
Knowledge Points Detail Section1 Introduction to WiMAX 1.1 Wireless Introduction 1.1.1 Wireless Network Topologies 1.1.2 Wireless Technologies 1.1.3 Kinds of Wireless Networks 1.1.4 Wireless Broadband Access (WBA) 1.2 Related Organization 1.2.1 IEEE 1.2.2 WiMAX Forum 1.3 What is WiMAX 1.3.1 What is WiMAX 1.3.2 What is 802.16d 1.3.3 What is 802.16e 1.3.4 WiMax Speed and Range 1.3.5 Why WiMAX1 1.3.6 WiMAX Goals 1.4 Salient Features of WiMAX 1.4.1 OFDM-based physical layer 1.4.2 Very High Peak Date Rate
Certification Document of ZTE Skill Center Percentage of Test Questions for ZTE Employees Percentage of Test Questions for Outsourcing Parties Percentage of Test Questions for Customers
I D
Knowledge Points Detail 1.4.3 Scalable bandwidth and rate support 1.4.4 Adaptive modulation and coding (AMC) 1.4.5 Link-layer retransmissions 1.4.6 Support for TDD and FDD 1.4.7 Orthogonal frequency division multiple access (OFDMA) 1.4.8 Flexible and dynamic per user resource allocation 1.4.9 Support for advanced antenna techniques 1.4.10 Qulity of service support 1.4.11 Robust security 1.4.12 Support for mobility 1.4.13 IP-based architecture Section2 OFDM 2.1 OFDM System Description 2.2 OFDM Orthogonality 2.3 How to Overcome Inter Symbol Interference (ISI) 2.4 How to Overcome Inter Carrier Interference (ICI) Section3 OFDMA 3.1 OFDMA Basics 3.2 OFDMA Symbol Structure and SubChannelization 3.3 Scalable OFDMA 3.4 TDD Frame Structure 3.5 Other Advanced PHY Layer Features 3.6 Difference between OFDMA and OFDM Section4 WiMAX MAC 4.1 Common MAC Concepts 4.1.1 CS Sublayer 4.1.2 MAC CPS Sublayer 4.2 Quality of Service (QoS) Support 4.3 MAC Scheduling Service 4.4 Mobility Management 4.4.1 Power Management 4.4.2 Handoff 4.5 Security Section5 WiMAX Advanced Features 5.1 Smart Antenna Technologies 5.2 Fractional Frequency
Certification Document of ZTE Skill Center Percentage of Test Questions for ZTE Employees Percentage of Test Questions for Outsourcing Parties Percentage of Test Questions for Customers
I D
Knowledge Points Detail Reuse 5.3 Multicast and Broadcast Service (MBS) Section6 WiMAX Network Architecture Section7 WiMAX Channel Estimation 7.1 Introduction 7.2 Channel Estimation 7.2.1 Transmitter 7.2.2 Channel 7.2.3 Reciever Section8 WiMAX Major Benefits Section1 Overview and Process of Wireless Network Planning 1.1 Definition of Wireless Network Planning 1.2 Objectives of WiMAX Network Planning 1.3 Process of WiMAX Wireless Network Planning Section2 Network Dimensioning and Design 2.1 Requirements 2.2 WiMAX Cell Site Design 2.3 WiMAX Networks Dimensioning 2.3.1 Deployment Scenarios 2.3.2 Dimensioning Process 2.4 Business Plan, Assets, and Key Performance Indicators 2.5 Strategy 2.6 Coverage Dimensioning 2.7 Capacity Dimensioning 2.8 Joint Dimensioning Section3 Radio Propagation models 3.1 Free-Space Model 3.2 SUI Model 3.3 Standard Macrocell Propagation Model Section4 WiMAX Coverage Planning 4.1 Overview of Link Budget 4.2 Physical Layer Parameters Meanings of PUSC in WiMAX 4.2.1 Link Budget of the WiMAX System 4.2.2 Overview of WiMAX Link Budget 4.3 Input and Output
45
45
45
Certification Document of ZTE Skill Center Percentage of Test Questions for ZTE Employees Percentage of Test Questions for Outsourcing Parties Percentage of Test Questions for Customers
I D
Knowledge Points Detail 4.3.1 Input Parameters 4.3.2 Compulsory Input Parameters 4.3.3 Default Parameters 4.4 Link Budget Table Section5 WiMAX Capacity Planning 5.1 Principles of Subscriber Predication 5.1.1 Methods of Subscriber Predication 5.2 Service Models 5.2.1 Voice Service Model 5.2.2 Data Service Model 5.3 WiMAX Capacity Planning 5.3.1 Physical Layer Traffic Calculation of Downlink Subframe 5.3.2 Physical Layer Traffic Calculation of Uplink Subframe 5.3.3 Summary of Traffic Calculation Section6 Detailed Calculation of Estimated Site Number 6.1 Site Number Estimation Based on Coverage Requirement 6.2 Site Number Estimation Based on Traffic Requirement Section7 Site Survey and Planning 7.1 Overview 7.2 Introduction to Site Survey 7.3 Available Site Survey and Selection 7.3.1 No Obvious Blocking Objects around the Site 7.3.2 Site Height 7.3.3 No Interference with Other Systems 7.4 Planned Site Survey and Selection 7.4.1 No Obvious Blocking Objects around the Site 7.4.2 Site Height 7.4.3 Distance between Site Location and Planned Site Location 7.5 Ultra-Wide Coverage Site Survey and Selection
Certification Document of ZTE Skill Center Percentage of Test Questions for ZTE Employees Percentage of Test Questions for Outsourcing Parties Percentage of Test Questions for Customers
I D
Knowledge Points Detail Section8 Antenna Selection 8.1 Overview 8.2 Antenna Selection 8.2.1 Frequency Range and Polarization Mode 8.2.2 Radiation Pattern, Horizontal BW, Vertical BW, and Gain 8.2.3 Downtilt Mode 8.2.4 Side Lobe Suppression and Null Fill 8.2.5 Front-to-back Ratio, Maximum Input Power, Third-order Intermodulation, Isolation 8.3 Selecting Antennas for Indoor Distribution Systems Section9 WiMAX Preamble & Neighbor Planning 9.1 Overview 9.2 Preamble & Neighbor Planning Flow 9.2.1 Preamble Planning Flow 9.2.2 Neighbor Planning Flow 9.3 Preamble Planning Procedure 9.4 Neighbor Planning via CNO 9.4.1 Neighbor Planning 9.4.2 Tips Section10 Tools Section1 Wireless Network Planning and Optimization Process 1.1 Basic Process Introduction 1.2 Requirement Analysis 1.3 Spectrum Scan 1.3.1 Scanning overview 1.3.2 Scanning test type and test tools 1.3.2.1 Test type 1.3.2.2 Test tools 1.3.2.3 Spectrum analyzer parameters setting 1.3.3 Test procedure 1.3.3.1 Drive test procedure 1.3.3.2 Fixed location test procedure 1.3.4 Analysis of test data 1.3.4.1 Analysis of drive test data 1.3.4.2 Analysis of fixed
37
37
37
Certification Document of ZTE Skill Center Percentage of Test Questions for ZTE Employees Percentage of Test Questions for Outsourcing Parties Percentage of Test Questions for Customers
I D
Knowledge Points Detail location test data 1.3.5 Analysis of interference in service areas 1.3.5.1 The influence of external interference 1.3.5.2 The influence of external interference on coverage 1.3.5.3 According to the result of frequency scanning export conclusions and scanning report. 1.3.6 System OMC uplink spectrum scanning instruction 1.3.6.1 Overview 1.3.6.2 Uplink spectrum scanning function 1.4 Single Station Test 1.4.1 Single station test scope and objective 1.4.2 Single station test verification requirement 1.4.2.1 Single site verification RNP 1.4.2.2 Coverage area verification 1.4.2.3 Coverage area KPI target 1.4.3 Single station test verification contents 1.4.3.1 Single site information verification 1.4.3.2 Functional test verification 1.4.3.3 Drive test result 1.4.4 Coverage test verification contents 1.4.4.1 Configuration information 1.4.4.2 Coverage polygon 1.4.4.3 Coverage street information 1.4.5 Single station and coverage test verification report 1.5 Calibration Test 1.6 Network Evaluation before Optimization 1.7 BS Cluster Optimization 1.8 Whole Network Optimization and Network Evaluation 1.9 Project Acceptance Test and Report Hand in
Certification Document of ZTE Skill Center Percentage of Test Questions for ZTE Employees Percentage of Test Questions for Outsourcing Parties Percentage of Test Questions for Customers
I D
Knowledge Points Detail Section2 Network Planning Issue 2.1 Optimization Test Tool Introduction 2.1.1 Optimization test tool CNT introduction 2.1.1.1 Overview 2.1.1.2 The use of ZXPOS CNT1 2.1.1.2.1 Test process 2.1.1.2.2 Hardware detection and configuration 2.1.1.2.3 Hardware configuration interface introduced 2.1.1.2.4 Hardware configuration interface introduced 2.1.1.3 Work interface 2.1.1.4 Window interface 2.1.1.4.1 Title bar 2.1.1.4.2 Menu bar 2.1.1.4.3 Status bar 2.1.1.5 Toolbar 2.1.1.6 Replay toolbar 2.1.1.7 Right key menu toolbar 2.1.1.8 Menu and function analysis 2.1.1.9 Explorer window 2.1.1.9.1 Device Config 2.1.1.9.2 Windows 2.1.1.10 Refresh rate to adjust the window style and the curve 2.1.1.10.1 Adjust wireless parameters window refresh rate chart 2.1.1.10.2 Style curve adjustment 2.1.1.11 Test software projects 2.1.1.12 Export of test data 2.1.1.12.1 Export pages 2.1.1.13 Subsection of test data 2.1.1.14 Route map 2.1.1.14.1 Toolbar introduction 2.1.1.14.2 Control Layer 2.1.1.14.3 Theme setting 2.1.1.14.4 Map parameters setting 2.1.1.14.5 Custom label settings
Certification Document of ZTE Skill Center Percentage of Test Questions for ZTE Employees Percentage of Test Questions for Outsourcing Parties Percentage of Test Questions for Customers
I D
Knowledge Points Detail 2.1.1.14.6 Marker parameters 2.1.1.14.7 Find the base station 2.1.1.15 Information display and switch 2.1.1.15.1 Values (WiMAX) 2.1.1.15.2 Information 2.1.1.15.3 Legend 2.1.1.16 Drive test map 2.1.1.17 Data test 2.1.1.17.1 Plans setting page automatic test plan 2.1.1.17.2 Message Test page news shows 2.1.1.17.3 Throughput shows the throughput of the page 2.1.1.17.4 Statistics show page 2.1.1.18 Data Monitor 2.1.1.19 WiMAX Logon Tool 2.1.1.20 WiMAX Logon Tool 2.1.1.21 WiMAX Communication Info 2.1.1.22 WiMAX Air Interface Message 2.1.1.23 WiMAX Modulation Statistics 2.1.1.24 WiMAX Date Throughput 2.1.2 Optimization analysis tool CNA introduction 2.1.2.1 Introduction 2.1.2.2 Terms, definitions and abbreviations 2.1.2.3 Comprehensive description 2.1.2.3.1 Background 2.1.2.3.2 Product Overview 2.1.2.4 Specific functions description 2.1.2.4.1 Basic function analysis 2.1.2.4.2 Segment'RSSI and Segment'CINR functions 2.1.2.4.3 Call event analysis and delay statistics 2.1.2.4.4 Analysis of handover events 2.1.2.4.5 Interference Analysis 2.1.2.4.6 Analysis of dropped calls 2.1.2.4.7 Calls, handover of
Certification Document of ZTE Skill Center Percentage of Test Questions for ZTE Employees Percentage of Test Questions for Outsourcing Parties Percentage of Test Questions for Customers
I D
Knowledge Points Detail the incident shows the geographical 2.1.2.4.8 Jitter Analysis of packet loss rate 2.1.2.4.9 Table part of the meaning of Item Value 2.2 Optimize Test 2.2.1 Test Content 2.2.1.1 Cover Test 2.2.1.2 Throughout Test 2.2.1.3 Cut-over Test 2.2.1.4 Calling Test 2.2.1.5 Operation Test 2.2.1.6 Handoff 2.2.1.7 Lose Words Rate 2.2.2 Testing Method 2.2.2.1 DT Testing 2.2.2.2 CQT Testing 2.3 RF Optimizing Subject 2.3.1 RF Optimizing Goal 2.3.2 Antenna Optimization 2.3.3 Calibration Power Optimizing 2.3.4 Interferences Searching and Frequency Scanning 2.4 Access and Paging 2.4.1 Basic connection flow 2.4.1.1 Connection flow chart 2.4.1.2 Small area option and downlink synchronization 2.4.1.2.1 OMC parameters chart below 2.4.1.2.2 Physicalal Layer Parameter OMC Configuration 2.4.1.3 Ranging 2.4.1.3.1 Ranging parameters 2.4.1.3.2 Ranging OMC parameter configuration 2.4.1.4 SBC negotiation ability 2.4.1.4.1 SBC parameters 2.4.1.4.2 SBC OMC parameters configuration 2.4.1.5 Coding and authorization 2.4.1.5.1 OMC parameters configuration 2.4.1.6 REG ability negotiation 2.4.1.7 Service flow setup
Certification Document of ZTE Skill Center Percentage of Test Questions for ZTE Employees Percentage of Test Questions for Outsourcing Parties Percentage of Test Questions for Customers
I D
Knowledge Points Detail 2.4.1.8 Obtaining IP 2.4.2 Idle Idle model and paging flow 2.4.2.1 The function of idle model 2.4.2.2 Paging chart 2.4.2.3 Entering idle flow chart 2.4.2.4 Location update 2.4.2.5 Paging flow 2.4.2.6 Exit idel state flow 2.4.2.6.1 OMC parameters configuration 2.5 Handover Technology 2.5.1 Handover types 2.5.1.1 Hard Handover (HHO) 2.5.1.2 Fast BS Switching (FBSS) 2.5.1.3 Macro Diversity HandoverMDHO 2.5.2 HHO workflow 2.5.3 The related parameters configure of HO 2.5.3.1 HO configure page 2.5.3.2 HO parameter instruction 2.5.3.3 Neighbor configure page 2.5.3.4 Neighbor parameters explan 2.5.3.5 Trigger configure 2.5.3.6 Trigger parameter instruction 2.6 Power Control optimization 2.6.1 PC and AMC principle 2.6.1.1 The purpose of PC 2.6.1.2 The principles of PC 2.6.1.3 Power Control Classification 2.6.1.4 AMC 2.6.1.5 PC and AMC arithmetic 2.6.2 Power Control and AMC configure 2.6.2.1 DL Burst Profile configure 2.6.2.2 DL Burst Profile parameters instruction 2.6.2.3 UL Burst Profile configure 2.6.2.4 UL Burst Profile parameter instruction 2.6.2.5 AMC configure
10
Certification Document of ZTE Skill Center Percentage of Test Questions for ZTE Employees Percentage of Test Questions for Outsourcing Parties Percentage of Test Questions for Customers
I D
Knowledge Points Detail 2.6.2.6 AMC frequent parameters instructions 2.6.2.7 PC configure parameters 2.6.2.8 PC parameters explanation 2.7 Admission and congestion control 2.7.1 QOS of the airinterface resource of WiMAX 2.7.1.1 Air-interface resource 2.7.1.2 Flux of subscribers service-flow 2.7.1.3 Types of service-flow 2.7.1.4 Admission and congestion control 2.7.2 Admission Control 2.7.2.1 Basic principle 2.7.2.2 Realization method 2.7.2.3 The application scene of admission control 2.7.2.4 Serveral terms considering by admission control 2.7.2.5 Admission control parameters explanation 2.7.2.6 Admission configure page 2.7.3 Congestion control 2.7.3.1 Basic principle 2.7.3.2 Realized mode 2.7.3.3 The scene of congestion control 2.7.3.4 Congestion control parameter 2.7.3.5 Congestion control configure page Section3 WiMAX Terminal Introduction 3.1 Summary of frequent terminal sort summary 3.1.1 Sort according to the shape and interface 3.1.2 Sort according to the chip vendor 3.2 Detail configuration instruction of frequent terminal 3.2.1 USI CPE terminal 3.2.1.1 Configuration parameters operation instruction 3.2.1.2 Use command 3.2.2 ZTE terminal (base on
11
Certification Document of ZTE Skill Center Percentage of Test Questions for ZTE Employees Percentage of Test Questions for Outsourcing Parties Percentage of Test Questions for Customers
I D
Knowledge Points Detail Beceem chip) 3.2.2.1 Configuration parameters operation instruction 3.2.2.2 TTIS authentication configuration 3.2.3 GCT terminal 3.2.3.1 Configuration parameters operation instruction 3.2.3.2 Common command instruction 3.2.3.2.1 Set frequency 3.2.3.2.2 Print packet command 3.2.3.2.3 Dump command 3.2.3.2.4 Configuration command Section4 WiMAX Network KPI Introduction 4.1 WiMAX network performance KPI introduction 4.1.1 KPI concept 4.1.2 WiMAX KPI introduce 4.1.2.1 Coverage KPI 4.1.2.1.1 DL/UL RSSI 4.1.2.1.2 DL/UL CINR 4.1.2.1.2 DL/UL Tx Power 4.1.2.2 System Performance KPI 4.1.2.2.1 Initial Access 4.1.2.2.2 Service Flow Setup 4.1.2.2.3 System Connection Drop Rate 4.1.2.2.4 Hard Handover 4.1.2.2.5 Delay 4.1.2.2.6 Jitter 4.1.2.2.7 Packet Loss 4.1.2.3 KPI recommend value 4.2 KPI statistic tool CNO2 introduction 4.2.1 Introduction of CNO2 4.2.2 Benefit of using CNO2 4.2.3 Data Characteristic of CNO2 4.2.4 Advantage of CNO2 4.2.5 Main Operation Statistic steps of CNO2 for WiMAX Section1 Network Simulation Introduction 1.1 Overview of network simulation
12
Certification Document of ZTE Skill Center Percentage of Test Questions for ZTE Employees Percentage of Test Questions for Outsourcing Parties Percentage of Test Questions for Customers
I D
Knowledge Points Detail 1.2 Network Simulation basics 1.2.1 Digital Map 1.2.2 Universal Transverse Mercator (UTM) 1.3 Wireless Propagation Scenarios Definition 1.4 Model Selection Section2 Propagation Model Tuning 2.1 Data Collection 2.2 Data Processing 2.3 Data Analysis 2.4 Assessment Precision Section3 Simulation Flow 3.1 Data Preparation 3.2 Path Loss Prediction 3.3 Traffic Distribution Creation 3.4 Wireless Network Simulation Analysis 3.5 Outputting Network Simulation Design Report Section4 Quality Assessment on Wireless Network Simulation Design 4.1 Acquiring Network Performance Data 4.2 Comparison Analysis 4.3 Deduction on Network Simulation Quality Section5 Simulation in Network Planning and Optimization 5.1 Network Topology Design 5.2 Network KPI Prediction 5.3 Capacity Expansion and Coverage Issue Section6 Static Simulation Algorithm 6.1 Effective Site Antenna Height Calculation Methods 6.2 Diffraction Loss Calculation (Knife Edge) Techniques 6.3 Giovaneli Diffraction Loss Technique
Total score 100 Question types The test focuses on examining the understanding on related theories. Altogether there are 64 test questions involving Single Choice, Multiple ChoiceGap Filling and Brief Answer types. Level-III ZTE Employee Single Choice Multiple Choice Judgeme nt Gap Filling Brief Answer 4 (5Score/Ques. )
Percentage of Test Questions for Customers 5
20 20 20 (1Score/Ques (1Score/Ques (2Score/Ques .) .) .) Certification contents and percentage of each tested knowledge point
Knowledge Point Name Percentage of Test Questions for ZTE Employees 5 Percentage of Test Questions for Outsourcing Parties 5
I D 1
Knowledge Points Detail Section1 Introduction to WiMAX 1.1 Wireless Introduction 1.1.1 Wireless Network Topologies 1.1.2 Wireless Technologies 1.1.3 Kinds of Wireless Networks 1.1.4 Wireless Broadband Access (WBA) 1.2 Related Organization 1.2.1 IEEE 1.2.2 WiMAX Forum 1.3 What is WiMAX 1.3.1 What is WiMAX 1.3.2 What is 802.16d 1.3.3 What is 802.16e 1.3.4 WiMax Speed and Range 1.3.5 Why WiMAX1 1.3.6 WiMAX Goals 1.4 Salient Features of WiMAX 1.4.1 OFDM-based physical layer 1.4.2 Very High Peak Date Rate 1.4.3 Scalable bandwidth and rate support 1.4.4 Adaptive modulation and coding (AMC) 1.4.5 Link-layer retransmissions 1.4.6 Support for TDD and FDD 1.4.7 Orthogonal frequency division multiple access (OFDMA) 1.4.8 Flexible and dynamic
14
Certification Document of ZTE Skill Center Percentage of Test Questions for ZTE Employees Percentage of Test Questions for Outsourcing Parties Percentage of Test Questions for Customers
I D
Knowledge Points Detail per user resource allocation 1.4.9 Support for advanced antenna techniques 1.4.10 Qulity of service support 1.4.11 Robust security 1.4.12 Support for mobility 1.4.13 IP-based architecture Section2 OFDM 2.1 OFDM System Description 2.2 OFDM Orthogonality 2.3 How to Overcome Inter Symbol Interference (ISI) 2.4 How to Overcome Inter Carrier Interference (ICI) Section3 OFDMA 3.1 OFDMA Basics 3.2 OFDMA Symbol Structure and SubChannelization 3.3 Scalable OFDMA 3.4 TDD Frame Structure 3.5 Other Advanced PHY Layer Features 3.6 Difference between OFDMA and OFDM Section4 WiMAX MAC 4.1 Common MAC Concepts 4.1.1 CS Sublayer 4.1.2 MAC CPS Sublayer 4.2 Quality of Service (QoS) Support 4.3 MAC Scheduling Service 4.4 Mobility Management 4.4.1 Power Management 4.4.2 Handoff 4.5 Security Section5 WiMAX Advanced Features 5.1 Smart Antenna Technologies 5.2 Fractional Frequency Reuse 5.3 Multicast and Broadcast Service (MBS) Section6 WiMAX Network Architecture Section7 WiMAX Channel Estimation 7.1 Introduction 7.2 Channel Estimation 7.2.1 Transmitter 7.2.2 Channel 7.2.3 Reciever
15
Certification Document of ZTE Skill Center Percentage of Test Questions for ZTE Employees 40 Percentage of Test Questions for Outsourcing Parties 40 Percentage of Test Questions for Customers 40
I D
Knowledge Points Detail Section8 WiMAX Major Benefits Section1 Overview and Process of Wireless Network Planning 1.1 Definition of Wireless Network Planning 1.2 Objectives of WiMAX Network Planning 1.3 Process of WiMAX Wireless Network Planning Section2 Network Dimensioning and Design 2.1 Requirements 2.2 WiMAX Cell Site Design 2.3 WiMAX Networks Dimensioning 2.3.1 Deployment Scenarios 2.3.2 Dimensioning Process 2.4 Business Plan, Assets, and Key Performance Indicators 2.5 Strategy 2.6 Coverage Dimensioning 2.7 Capacity Dimensioning 2.8 Joint Dimensioning Section3 Radio Propagation models 3.1 Free-Space Model 3.2 SUI Model 3.3 Standard Macrocell Propagation Model Section4 WiMAX Coverage Planning 4.1 Overview of Link Budget 4.2 Physical Layer Parameters Meanings of PUSC in WiMAX 4.2.1 Link Budget of the WiMAX System 4.2.2 Overview of WiMAX Link Budget 4.3 Input and Output 4.3.1 Input Parameters 4.3.2 Compulsory Input Parameters 4.3.3 Default Parameters 4.4 Link Budget Table Section5 WiMAX Capacity Planning 5.1 Principles of Subscriber Predication 5.1.1 Methods of Subscriber Predication 5.2 Service Models
16
Certification Document of ZTE Skill Center Percentage of Test Questions for ZTE Employees Percentage of Test Questions for Outsourcing Parties Percentage of Test Questions for Customers
I D
Knowledge Points Detail 5.2.1 Voice Service Model 5.2.2 Data Service Model 5.3 WiMAX Capacity Planning 5.3.1 Physical Layer Traffic Calculation of Downlink Subframe 5.3.2 Physical Layer Traffic Calculation of Uplink Subframe 5.3.3 Summary of Traffic Calculation Section6 Detailed Calculation of Estimated Site Number 6.1 Site Number Estimation Based on Coverage Requirement 6.2 Site Number Estimation Based on Traffic Requirement Section7 Site Survey and Planning 7.1 Overview 7.2 Introduction to Site Survey 7.3 Available Site Survey and Selection 7.3.1 No Obvious Blocking Objects around the Site 7.3.2 Site Height 7.3.3 No Interference with Other Systems 7.4 Planned Site Survey and Selection 7.4.1 No Obvious Blocking Objects around the Site 7.4.2 Site Height 7.4.3 Distance between Site Location and Planned Site Location 7.5 Ultra-Wide Coverage Site Survey and Selection Section8 Antenna Selection 8.1 Overview 8.2 Antenna Selection 8.2.1 Frequency Range and Polarization Mode 8.2.2 Radiation Pattern, Horizontal BW, Vertical BW, and Gain 8.2.3 Downtilt Mode 8.2.4 Side Lobe Suppression and Null Fill 8.2.5 Front-to-back Ratio,
17
Certification Document of ZTE Skill Center Percentage of Test Questions for ZTE Employees Percentage of Test Questions for Outsourcing Parties Percentage of Test Questions for Customers
I D
Knowledge Points Detail Maximum Input Power, Third-order Intermodulation, Isolation 8.3 Selecting Antennas for Indoor Distribution Systems Section9 WiMAX Preamble & Neighbor Planning 9.1 Overview 9.2 Preamble & Neighbor Planning Flow 9.2.1 Preamble Planning Flow 9.2.2 Neighbor Planning Flow 9.3 Preamble Planning Procedure 9.4 Neighbor Planning via CNO 9.4.1 Neighbor Planning 9.4.2 Tips Section10 Tools Section1 Wireless Network Planning and Optimization Process 1.1 Basic Process Introduction 1.2 Requirement Analysis 1.3 Spectrum Scan 1.3.1 Scanning overview 1.3.2 Scanning test type and test tools 1.3.2.1 Test type 1.3.2.2 Test tools 1.3.2.3 Spectrum analyzer parameters setting 1.3.3 Test procedure 1.3.3.1 Drive test procedure 1.3.3.2 Fixed location test procedure 1.3.4 Analysis of test data 1.3.4.1 Analysis of drive test data 1.3.4.2 Analysis of fixed location test data 1.3.5 Analysis of interference in service areas 1.3.5.1 The influence of external interference 1.3.5.2 The influence of external interference on coverage 1.3.5.3 According to the result of frequency scanning export conclusions and scanning report.
40
40
40
18
Certification Document of ZTE Skill Center Percentage of Test Questions for ZTE Employees Percentage of Test Questions for Outsourcing Parties Percentage of Test Questions for Customers
I D
Knowledge Points Detail 1.3.6 System OMC uplink spectrum scanning instruction 1.3.6.1 Overview 1.3.6.2 Uplink spectrum scanning function 1.4 Single Station Test 1.4.1 Single station test scope and objective 1.4.2 Single station test verification requirement 1.4.2.1 Single site verification RNP 1.4.2.2 Coverage area verification 1.4.2.3 Coverage area KPI target 1.4.3 Single station test verification contents 1.4.3.1 Single site information verification 1.4.3.2 Functional test verification 1.4.3.3 Drive test result 1.4.4 Coverage test verification contents 1.4.4.1 Configuration information 1.4.4.2 Coverage polygon 1.4.4.3 Coverage street information 1.4.5 Single station and coverage test verification report 1.5 Calibration Test 1.6 Network Evaluation before Optimization 1.7 BS Cluster Optimization 1.8 Whole Network Optimization and Network Evaluation 1.9 Project Acceptance Test and Report Hand in Section2 Network Planning Issue 2.1 Optimization Test Tool Introduction 2.1.1 Optimization test tool CNT introduction 2.1.1.1 Overview 2.1.1.2 The use of ZXPOS CNT1 2.1.1.2.1 Test process 2.1.1.2.2 Hardware detection and configuration
19
Certification Document of ZTE Skill Center Percentage of Test Questions for ZTE Employees Percentage of Test Questions for Outsourcing Parties Percentage of Test Questions for Customers
I D
Knowledge Points Detail 2.1.1.2.3 Hardware configuration interface introduced 2.1.1.2.4 Hardware configuration interface introduced 2.1.1.3 Work interface 2.1.1.4 Window interface 2.1.1.4.1 Title bar 2.1.1.4.2 Menu bar 2.1.1.4.3 Status bar 2.1.1.5 Toolbar 2.1.1.6 Replay toolbar 2.1.1.7 Right key menu toolbar 2.1.1.8 Menu and function analysis 2.1.1.9 Explorer window 2.1.1.9.1 Device Config 2.1.1.9.2 Windows 2.1.1.10 Refresh rate to adjust the window style and the curve 2.1.1.10.1 Adjust wireless parameters window refresh rate chart 2.1.1.10.2 Style curve adjustment 2.1.1.11 Test software projects 2.1.1.12 Export of test data 2.1.1.12.1 Export pages 2.1.1.13 Subsection of test data 2.1.1.14 Route map 2.1.1.14.1 Toolbar introduction 2.1.1.14.2 Control Layer 2.1.1.14.3 Theme setting 2.1.1.14.4 Map parameters setting 2.1.1.14.5 Custom label settings 2.1.1.14.6 Marker parameters 2.1.1.14.7 Find the base station 2.1.1.15 Information display and switch 2.1.1.15.1 Values (WiMAX) 2.1.1.15.2 Information 2.1.1.15.3 Legend 2.1.1.16 Drive test map 2.1.1.17 Data test 2.1.1.17.1 Plans setting
20
Certification Document of ZTE Skill Center Percentage of Test Questions for ZTE Employees Percentage of Test Questions for Outsourcing Parties Percentage of Test Questions for Customers
I D
Knowledge Points Detail page automatic test plan 2.1.1.17.2 Message Test page news shows 2.1.1.17.3 Throughput shows the throughput of the page 2.1.1.17.4 Statistics show page 2.1.1.18 Data Monitor 2.1.1.19 WiMAX Logon Tool 2.1.1.20 WiMAX Logon Tool 2.1.1.21 WiMAX Communication Info 2.1.1.22 WiMAX Air Interface Message 2.1.1.23 WiMAX Modulation Statistics 2.1.1.24 WiMAX Date Throughput 2.1.2 Optimization analysis tool CNA introduction 2.1.2.1 Introduction 2.1.2.2 Terms, definitions and abbreviations 2.1.2.3 Comprehensive description 2.1.2.3.1 Background 2.1.2.3.2 Product Overview 2.1.2.4 Specific functions description 2.1.2.4.1 Basic function analysis 2.1.2.4.2 Segment'RSSI and Segment'CINR functions 2.1.2.4.3 Call event analysis and delay statistics 2.1.2.4.4 Analysis of handover events 2.1.2.4.5 Interference Analysis 2.1.2.4.6 Analysis of dropped calls 2.1.2.4.7 Calls, handover of the incident shows the geographical 2.1.2.4.8 Jitter Analysis of packet loss rate 2.1.2.4.9 Table part of the meaning of Item Value 2.2 Optimize Test 2.2.1 Test Content 2.2.1.1 Cover Test 2.2.1.2 Throughout Test 2.2.1.3 Cut-over Test 2.2.1.4 Calling Test
21
Certification Document of ZTE Skill Center Percentage of Test Questions for ZTE Employees Percentage of Test Questions for Outsourcing Parties Percentage of Test Questions for Customers
I D
Knowledge Points Detail 2.2.1.5 Operation Test 2.2.1.6 Handoff 2.2.1.7 Lose Words Rate 2.2.2 Testing Method 2.2.2.1 DT Testing 2.2.2.2 CQT Testing 2.3 RF Optimizing Subject 2.3.1 RF Optimizing Goal 2.3.2 Antenna Optimization 2.3.3 Calibration Power Optimizing 2.3.4 Interferences Searching and Frequency Scanning 2.4 Access and Paging 2.4.1 Basic connection flow 2.4.1.1 Connection flow chart 2.4.1.2 Small area option and downlink synchronization 2.4.1.2.1 OMC parameters chart below 2.4.1.2.2 Physicalal Layer Parameter OMC Configuration 2.4.1.3 Ranging 2.4.1.3.1 Ranging parameters 2.4.1.3.2 Ranging OMC parameter configuration 2.4.1.4 SBC negotiation ability 2.4.1.4.1 SBC parameters 2.4.1.4.2 SBC OMC parameters configuration 2.4.1.5 Coding and authorization 2.4.1.5.1 OMC parameters configuration 2.4.1.6 REG ability negotiation 2.4.1.7 Service flow setup 2.4.1.8 Obtaining IP 2.4.2 Idle Idle model and paging flow 2.4.2.1 The function of idle model 2.4.2.2 Paging chart 2.4.2.3 Entering idle flow chart 2.4.2.4 Location update 2.4.2.5 Paging flow 2.4.2.6 Exit idel state flow 2.4.2.6.1 OMC parameters
22
Certification Document of ZTE Skill Center Percentage of Test Questions for ZTE Employees Percentage of Test Questions for Outsourcing Parties Percentage of Test Questions for Customers
I D
Knowledge Points Detail configuration 2.5 Handover Technology 2.5.1 Handover types 2.5.1.1 Hard Handover (HHO) 2.5.1.2 Fast BS Switching (FBSS) 2.5.1.3 Macro Diversity HandoverMDHO 2.5.2 HHO workflow 2.5.3 The related parameters configure of HO 2.5.3.1 HO configure page 2.5.3.2 HO parameter instruction 2.5.3.3 Neighbor configure page 2.5.3.4 Neighbor parameters explan 2.5.3.5 Trigger configure 2.5.3.6 Trigger parameter instruction 2.6 Power Control optimization 2.6.1 PC and AMC principle 2.6.1.1 The purpose of PC 2.6.1.2 The principles of PC 2.6.1.3 Power Control Classification 2.6.1.4 AMC 2.6.1.5 PC and AMC arithmetic 2.6.2 Power Control and AMC configure 2.6.2.1 DL Burst Profile configure 2.6.2.2 DL Burst Profile parameters instruction 2.6.2.3 UL Burst Profile configure 2.6.2.4 UL Burst Profile parameter instruction 2.6.2.5 AMC configure 2.6.2.6 AMC frequent parameters instructions 2.6.2.7 PC configure parameters 2.6.2.8 PC parameters explanation 2.7 Admission and congestion control 2.7.1 QOS of the airinterface resource of WiMAX 2.7.1.1 Air-interface resource
23
Certification Document of ZTE Skill Center Percentage of Test Questions for ZTE Employees Percentage of Test Questions for Outsourcing Parties Percentage of Test Questions for Customers
I D
Knowledge Points Detail 2.7.1.2 Flux of subscribers service-flow 2.7.1.3 Types of service-flow 2.7.1.4 Admission and congestion control 2.7.2 Admission Control 2.7.2.1 Basic principle 2.7.2.2 Realization method 2.7.2.3 The application scene of admission control 2.7.2.4 Serveral terms considering by admission control 2.7.2.5 Admission control parameters explanation 2.7.2.6 Admission configure page 2.7.3 Congestion control 2.7.3.1 Basic principle 2.7.3.2 Realized mode 2.7.3.3 The scene of congestion control 2.7.3.4 Congestion control parameter 2.7.3.5 Congestion control configure page Section3 WiMAX Terminal Introduction 3.1 Summary of frequent terminal sort summary 3.1.1 Sort according to the shape and interface 3.1.2 Sort according to the chip vendor 3.2 Detail configuration instruction of frequent terminal 3.2.1 USI CPE terminal 3.2.1.1 Configuration parameters operation instruction 3.2.1.2 Use command 3.2.2 ZTE terminal (base on Beceem chip) 3.2.2.1 Configuration parameters operation instruction 3.2.2.2 TTIS authentication configuration 3.2.3 GCT terminal 3.2.3.1 Configuration parameters operation instruction 3.2.3.2 Common command instruction
24
Certification Document of ZTE Skill Center Percentage of Test Questions for ZTE Employees Percentage of Test Questions for Outsourcing Parties Percentage of Test Questions for Customers
I D
Knowledge Points Detail 3.2.3.2.1 Set frequency 3.2.3.2.2 Print packet command 3.2.3.2.3 Dump command 3.2.3.2.4 Configuration command Section4 WiMAX Network KPI Introduction 4.1 WiMAX network performance KPI introduction 4.1.1 KPI concept 4.1.2 WiMAX KPI introduce 4.1.2.1 Coverage KPI 4.1.2.1.1 DL/UL RSSI 4.1.2.1.2 DL/UL CINR 4.1.2.1.2 DL/UL Tx Power 4.1.2.2 System Performance KPI 4.1.2.2.1 Initial Access 4.1.2.2.2 Service Flow Setup 4.1.2.2.3 System Connection Drop Rate 4.1.2.2.4 Hard Handover 4.1.2.2.5 Delay 4.1.2.2.6 Jitter 4.1.2.2.7 Packet Loss 4.1.2.3 KPI recommend value 4.2 KPI statistic tool CNO2 introduction 4.2.1 Introduction of CNO2 4.2.2 Benefit of using CNO2 4.2.3 Data Characteristic of CNO2 4.2.4 Advantage of CNO2 4.2.5 Main Operation Statistic steps of CNO2 for WiMAX Section1 Network Simulation Introduction 1.1 Overview of network simulation 1.2 Network Simulation basics 1.2.1 Digital Map 1.2.2 Universal Transverse Mercator (UTM) 1.3 Wireless Propagation Scenarios Definition 1.4 Model Selection Section2 Propagation Model Tuning 2.1 Data Collection 2.2 Data Processing
15
15
15
25
Certification Document of ZTE Skill Center Percentage of Test Questions for ZTE Employees Percentage of Test Questions for Outsourcing Parties Percentage of Test Questions for Customers
I D
Knowledge Points Detail 2.3 Data Analysis 2.4 Assessment Precision Section3 Simulation Flow 3.1 Data Preparation 3.2 Path Loss Prediction 3.3 Traffic Distribution Creation 3.4 Wireless Network Simulation Analysis 3.5 Outputting Network Simulation Design Report Section4 Quality Assessment on Wireless Network Simulation Design 4.1 Acquiring Network Performance Data 4.2 Comparison Analysis 4.3 Deduction on Network Simulation Quality Section5 Simulation in Network Planning and Optimization 5.1 Network Topology Design 5.2 Network KPI Prediction 5.3 Capacity Expansion and Coverage Issue Section6 Static Simulation Algorithm 6.1 Effective Site Antenna Height Calculation Methods 6.2 Diffraction Loss Calculation (Knife Edge) Techniques 6.3 Giovaneli Diffraction Loss Technique
Choice
nt 5 (4Score/Ques. )
20 20 20 (1Score/Ques (1Score/Ques (2Score/Ques .) .) .) Certification contents and percentage of each tested knowledge point
Percentage of Test Questions for ZTE Employees 5 Percentage of Test Questions for Outsourcing Parties 5
I D 1
Knowledge Points Detail Section1 Introduction to WiMAX 1.1 Wireless Introduction 1.1.1 Wireless Network Topologies 1.1.2 Wireless Technologies 1.1.3 Kinds of Wireless Networks 1.1.4 Wireless Broadband Access (WBA) 1.2 Related Organization 1.2.1 IEEE 1.2.2 WiMAX Forum 1.3 What is WiMAX 1.3.1 What is WiMAX 1.3.2 What is 802.16d 1.3.3 What is 802.16e 1.3.4 WiMax Speed and Range 1.3.5 Why WiMAX1 1.3.6 WiMAX Goals 1.4 Salient Features of WiMAX 1.4.1 OFDM-based physical layer 1.4.2 Very High Peak Date Rate 1.4.3 Scalable bandwidth and rate support 1.4.4 Adaptive modulation and coding (AMC) 1.4.5 Link-layer retransmissions 1.4.6 Support for TDD and FDD 1.4.7 Orthogonal frequency division multiple access (OFDMA) 1.4.8 Flexible and dynamic per user resource allocation 1.4.9 Support for advanced antenna techniques 1.4.10 Qulity of service support 1.4.11 Robust security 1.4.12 Support for mobility 1.4.13 IP-based architecture
27
Certification Document of ZTE Skill Center Percentage of Test Questions for ZTE Employees Percentage of Test Questions for Outsourcing Parties Percentage of Test Questions for Customers
I D
Knowledge Points Detail Section2 OFDM 2.1 OFDM System Description 2.2 OFDM Orthogonality 2.3 How to Overcome Inter Symbol Interference (ISI) 2.4 How to Overcome Inter Carrier Interference (ICI) Section3 OFDMA 3.1 OFDMA Basics 3.2 OFDMA Symbol Structure and SubChannelization 3.3 Scalable OFDMA 3.4 TDD Frame Structure 3.5 Other Advanced PHY Layer Features 3.6 Difference between OFDMA and OFDM Section4 WiMAX MAC 4.1 Common MAC Concepts 4.1.1 CS Sublayer 4.1.2 MAC CPS Sublayer 4.2 Quality of Service (QoS) Support 4.3 MAC Scheduling Service 4.4 Mobility Management 4.4.1 Power Management 4.4.2 Handoff 4.5 Security Section5 WiMAX Advanced Features 5.1 Smart Antenna Technologies 5.2 Fractional Frequency Reuse 5.3 Multicast and Broadcast Service (MBS) Section6 WiMAX Network Architecture Section7 WiMAX Channel Estimation 7.1 Introduction 7.2 Channel Estimation 7.2.1 Transmitter 7.2.2 Channel 7.2.3 Reciever Section8 WiMAX Major Benefits Section1 Overview and Process of Wireless Network Planning 1.1 Definition of Wireless Network Planning 1.2 Objectives of WiMAX
40
40
40
28
Certification Document of ZTE Skill Center Percentage of Test Questions for ZTE Employees Percentage of Test Questions for Outsourcing Parties Percentage of Test Questions for Customers
I D
Knowledge Points Detail Network Planning 1.3 Process of WiMAX Wireless Network Planning Section2 Network Dimensioning and Design 2.1 Requirements 2.2 WiMAX Cell Site Design 2.3 WiMAX Networks Dimensioning 2.3.1 Deployment Scenarios 2.3.2 Dimensioning Process 2.4 Business Plan, Assets, and Key Performance Indicators 2.5 Strategy 2.6 Coverage Dimensioning 2.7 Capacity Dimensioning 2.8 Joint Dimensioning Section3 Radio Propagation models 3.1 Free-Space Model 3.2 SUI Model 3.3 Standard Macrocell Propagation Model Section4 WiMAX Coverage Planning 4.1 Overview of Link Budget 4.2 Physical Layer Parameters Meanings of PUSC in WiMAX 4.2.1 Link Budget of the WiMAX System 4.2.2 Overview of WiMAX Link Budget 4.3 Input and Output 4.3.1 Input Parameters 4.3.2 Compulsory Input Parameters 4.3.3 Default Parameters 4.4 Link Budget Table Section5 WiMAX Capacity Planning 5.1 Principles of Subscriber Predication 5.1.1 Methods of Subscriber Predication 5.2 Service Models 5.2.1 Voice Service Model 5.2.2 Data Service Model 5.3 WiMAX Capacity Planning 5.3.1 Physical Layer Traffic Calculation of Downlink Subframe 5.3.2 Physical Layer Traffic
29
Certification Document of ZTE Skill Center Percentage of Test Questions for ZTE Employees Percentage of Test Questions for Outsourcing Parties Percentage of Test Questions for Customers
I D
Knowledge Points Detail Calculation of Uplink Subframe 5.3.3 Summary of Traffic Calculation Section6 Detailed Calculation of Estimated Site Number 6.1 Site Number Estimation Based on Coverage Requirement 6.2 Site Number Estimation Based on Traffic Requirement Section7 Site Survey and Planning 7.1 Overview 7.2 Introduction to Site Survey 7.3 Available Site Survey and Selection 7.3.1 No Obvious Blocking Objects around the Site 7.3.2 Site Height 7.3.3 No Interference with Other Systems 7.4 Planned Site Survey and Selection 7.4.1 No Obvious Blocking Objects around the Site 7.4.2 Site Height 7.4.3 Distance between Site Location and Planned Site Location 7.5 Ultra-Wide Coverage Site Survey and Selection Section8 Antenna Selection 8.1 Overview 8.2 Antenna Selection 8.2.1 Frequency Range and Polarization Mode 8.2.2 Radiation Pattern, Horizontal BW, Vertical BW, and Gain 8.2.3 Downtilt Mode 8.2.4 Side Lobe Suppression and Null Fill 8.2.5 Front-to-back Ratio, Maximum Input Power, Third-order Intermodulation, Isolation 8.3 Selecting Antennas for Indoor Distribution Systems Section9 WiMAX Preamble & Neighbor Planning 9.1 Overview
30
Certification Document of ZTE Skill Center Percentage of Test Questions for ZTE Employees Percentage of Test Questions for Outsourcing Parties Percentage of Test Questions for Customers
I D
Knowledge Points Detail 9.2 Preamble & Neighbor Planning Flow 9.2.1 Preamble Planning Flow 9.2.2 Neighbor Planning Flow 9.3 Preamble Planning Procedure 9.4 Neighbor Planning via CNO 9.4.1 Neighbor Planning 9.4.2 Tips Section10 Tools Section1 Wireless Network Planning and Optimization Process 1.1 Basic Process Introduction 1.2 Requirement Analysis 1.3 Spectrum Scan 1.3.1 Scanning overview 1.3.2 Scanning test type and test tools 1.3.2.1 Test type 1.3.2.2 Test tools 1.3.2.3 Spectrum analyzer parameters setting 1.3.3 Test procedure 1.3.3.1 Drive test procedure 1.3.3.2 Fixed location test procedure 1.3.4 Analysis of test data 1.3.4.1 Analysis of drive test data 1.3.4.2 Analysis of fixed location test data 1.3.5 Analysis of interference in service areas 1.3.5.1 The influence of external interference 1.3.5.2 The influence of external interference on coverage 1.3.5.3 According to the result of frequency scanning export conclusions and scanning report. 1.3.6 System OMC uplink spectrum scanning instruction 1.3.6.1 Overview 1.3.6.2 Uplink spectrum scanning function 1.4 Single Station Test 1.4.1 Single station test
40
40
40
31
Certification Document of ZTE Skill Center Percentage of Test Questions for ZTE Employees Percentage of Test Questions for Outsourcing Parties Percentage of Test Questions for Customers
I D
Knowledge Points Detail scope and objective 1.4.2 Single station test verification requirement 1.4.2.1 Single site verification RNP 1.4.2.2 Coverage area verification 1.4.2.3 Coverage area KPI target 1.4.3 Single station test verification contents 1.4.3.1 Single site information verification 1.4.3.2 Functional test verification 1.4.3.3 Drive test result 1.4.4 Coverage test verification contents 1.4.4.1 Configuration information 1.4.4.2 Coverage polygon 1.4.4.3 Coverage street information 1.4.5 Single station and coverage test verification report 1.5 Calibration Test 1.6 Network Evaluation before Optimization 1.7 BS Cluster Optimization 1.8 Whole Network Optimization and Network Evaluation 1.9 Project Acceptance Test and Report Hand in Section2 Network Planning Issue 2.1 Optimization Test Tool Introduction 2.1.1 Optimization test tool CNT introduction 2.1.1.1 Overview 2.1.1.2 The use of ZXPOS CNT1 2.1.1.2.1 Test process 2.1.1.2.2 Hardware detection and configuration 2.1.1.2.3 Hardware configuration interface introduced 2.1.1.2.4 Hardware configuration interface introduced 2.1.1.3 Work interface 2.1.1.4 Window interface
32
Certification Document of ZTE Skill Center Percentage of Test Questions for ZTE Employees Percentage of Test Questions for Outsourcing Parties Percentage of Test Questions for Customers
I D
Knowledge Points Detail 2.1.1.4.1 Title bar 2.1.1.4.2 Menu bar 2.1.1.4.3 Status bar 2.1.1.5 Toolbar 2.1.1.6 Replay toolbar 2.1.1.7 Right key menu toolbar 2.1.1.8 Menu and function analysis 2.1.1.9 Explorer window 2.1.1.9.1 Device Config 2.1.1.9.2 Windows 2.1.1.10 Refresh rate to adjust the window style and the curve 2.1.1.10.1 Adjust wireless parameters window refresh rate chart 2.1.1.10.2 Style curve adjustment 2.1.1.11 Test software projects 2.1.1.12 Export of test data 2.1.1.12.1 Export pages 2.1.1.13 Subsection of test data 2.1.1.14 Route map 2.1.1.14.1 Toolbar introduction 2.1.1.14.2 Control Layer 2.1.1.14.3 Theme setting 2.1.1.14.4 Map parameters setting 2.1.1.14.5 Custom label settings 2.1.1.14.6 Marker parameters 2.1.1.14.7 Find the base station 2.1.1.15 Information display and switch 2.1.1.15.1 Values (WiMAX) 2.1.1.15.2 Information 2.1.1.15.3 Legend 2.1.1.16 Drive test map 2.1.1.17 Data test 2.1.1.17.1 Plans setting page automatic test plan 2.1.1.17.2 Message Test page news shows 2.1.1.17.3 Throughput shows the throughput of the page 2.1.1.17.4 Statistics show page
33
Certification Document of ZTE Skill Center Percentage of Test Questions for ZTE Employees Percentage of Test Questions for Outsourcing Parties Percentage of Test Questions for Customers
I D
Knowledge Points Detail 2.1.1.18 Data Monitor 2.1.1.19 WiMAX Logon Tool 2.1.1.20 WiMAX Logon Tool 2.1.1.21 WiMAX Communication Info 2.1.1.22 WiMAX Air Interface Message 2.1.1.23 WiMAX Modulation Statistics 2.1.1.24 WiMAX Date Throughput 2.1.2 Optimization analysis tool CNA introduction 2.1.2.1 Introduction 2.1.2.2 Terms, definitions and abbreviations 2.1.2.3 Comprehensive description 2.1.2.3.1 Background 2.1.2.3.2 Product Overview 2.1.2.4 Specific functions description 2.1.2.4.1 Basic function analysis 2.1.2.4.2 Segment'RSSI and Segment'CINR functions 2.1.2.4.3 Call event analysis and delay statistics 2.1.2.4.4 Analysis of handover events 2.1.2.4.5 Interference Analysis 2.1.2.4.6 Analysis of dropped calls 2.1.2.4.7 Calls, handover of the incident shows the geographical 2.1.2.4.8 Jitter Analysis of packet loss rate 2.1.2.4.9 Table part of the meaning of Item Value 2.2 Optimize Test 2.2.1 Test Content 2.2.1.1 Cover Test 2.2.1.2 Throughout Test 2.2.1.3 Cut-over Test 2.2.1.4 Calling Test 2.2.1.5 Operation Test 2.2.1.6 Handoff 2.2.1.7 Lose Words Rate 2.2.2 Testing Method 2.2.2.1 DT Testing 2.2.2.2 CQT Testing 2.3 RF Optimizing Subject 2.3.1 RF Optimizing Goal
34
Certification Document of ZTE Skill Center Percentage of Test Questions for ZTE Employees Percentage of Test Questions for Outsourcing Parties Percentage of Test Questions for Customers
I D
Knowledge Points Detail 2.3.2 Antenna Optimization 2.3.3 Calibration Power Optimizing 2.3.4 Interferences Searching and Frequency Scanning 2.4 Access and Paging 2.4.1 Basic connection flow 2.4.1.1 Connection flow chart 2.4.1.2 Small area option and downlink synchronization 2.4.1.2.1 OMC parameters chart below 2.4.1.2.2 Physicalal Layer Parameter OMC Configuration 2.4.1.3 Ranging 2.4.1.3.1 Ranging parameters 2.4.1.3.2 Ranging OMC parameter configuration 2.4.1.4 SBC negotiation ability 2.4.1.4.1 SBC parameters 2.4.1.4.2 SBC OMC parameters configuration 2.4.1.5 Coding and authorization 2.4.1.5.1 OMC parameters configuration 2.4.1.6 REG ability negotiation 2.4.1.7 Service flow setup 2.4.1.8 Obtaining IP 2.4.2 Idle Idle model and paging flow 2.4.2.1 The function of idle model 2.4.2.2 Paging chart 2.4.2.3 Entering idle flow chart 2.4.2.4 Location update 2.4.2.5 Paging flow 2.4.2.6 Exit idel state flow 2.4.2.6.1 OMC parameters configuration 2.5 Handover Technology 2.5.1 Handover types 2.5.1.1 Hard Handover (HHO) 2.5.1.2 Fast BS Switching (FBSS) 2.5.1.3 Macro Diversity
35
Certification Document of ZTE Skill Center Percentage of Test Questions for ZTE Employees Percentage of Test Questions for Outsourcing Parties Percentage of Test Questions for Customers
I D
Knowledge Points Detail HandoverMDHO 2.5.2 HHO workflow 2.5.3 The related parameters configure of HO 2.5.3.1 HO configure page 2.5.3.2 HO parameter instruction 2.5.3.3 Neighbor configure page 2.5.3.4 Neighbor parameters explan 2.5.3.5 Trigger configure 2.5.3.6 Trigger parameter instruction 2.6 Power Control optimization 2.6.1 PC and AMC principle 2.6.1.1 The purpose of PC 2.6.1.2 The principles of PC 2.6.1.3 Power Control Classification 2.6.1.4 AMC 2.6.1.5 PC and AMC arithmetic 2.6.2 Power Control and AMC configure 2.6.2.1 DL Burst Profile configure 2.6.2.2 DL Burst Profile parameters instruction 2.6.2.3 UL Burst Profile configure 2.6.2.4 UL Burst Profile parameter instruction 2.6.2.5 AMC configure 2.6.2.6 AMC frequent parameters instructions 2.6.2.7 PC configure parameters 2.6.2.8 PC parameters explanation 2.7 Admission and congestion control 2.7.1 QOS of the airinterface resource of WiMAX 2.7.1.1 Air-interface resource 2.7.1.2 Flux of subscribers service-flow 2.7.1.3 Types of service-flow 2.7.1.4 Admission and congestion control 2.7.2 Admission Control 2.7.2.1 Basic principle 2.7.2.2 Realization method
36
Certification Document of ZTE Skill Center Percentage of Test Questions for ZTE Employees Percentage of Test Questions for Outsourcing Parties Percentage of Test Questions for Customers
I D
Knowledge Points Detail 2.7.2.3 The application scene of admission control 2.7.2.4 Serveral terms considering by admission control 2.7.2.5 Admission control parameters explanation 2.7.2.6 Admission configure page 2.7.3 Congestion control 2.7.3.1 Basic principle 2.7.3.2 Realized mode 2.7.3.3 The scene of congestion control 2.7.3.4 Congestion control parameter 2.7.3.5 Congestion control configure page Section3 WiMAX Terminal Introduction 3.1 Summary of frequent terminal sort summary 3.1.1 Sort according to the shape and interface 3.1.2 Sort according to the chip vendor 3.2 Detail configuration instruction of frequent terminal 3.2.1 USI CPE terminal 3.2.1.1 Configuration parameters operation instruction 3.2.1.2 Use command 3.2.2 ZTE terminal (base on Beceem chip) 3.2.2.1 Configuration parameters operation instruction 3.2.2.2 TTIS authentication configuration 3.2.3 GCT terminal 3.2.3.1 Configuration parameters operation instruction 3.2.3.2 Common command instruction 3.2.3.2.1 Set frequency 3.2.3.2.2 Print packet command 3.2.3.2.3 Dump command 3.2.3.2.4 Configuration command Section4 WiMAX Network KPI Introduction
37
Certification Document of ZTE Skill Center Percentage of Test Questions for ZTE Employees Percentage of Test Questions for Outsourcing Parties Percentage of Test Questions for Customers
I D
Knowledge Points Detail 4.1 WiMAX network performance KPI introduction 4.1.1 KPI concept 4.1.2 WiMAX KPI introduce 4.1.2.1 Coverage KPI 4.1.2.1.1 DL/UL RSSI 4.1.2.1.2 DL/UL CINR 4.1.2.1.2 DL/UL Tx Power 4.1.2.2 System Performance KPI 4.1.2.2.1 Initial Access 4.1.2.2.2 Service Flow Setup 4.1.2.2.3 System Connection Drop Rate 4.1.2.2.4 Hard Handover 4.1.2.2.5 Delay 4.1.2.2.6 Jitter 4.1.2.2.7 Packet Loss 4.1.2.3 KPI recommend value 4.2 KPI statistic tool CNO2 introduction 4.2.1 Introduction of CNO2 4.2.2 Benefit of using CNO2 4.2.3 Data Characteristic of CNO2 4.2.4 Advantage of CNO2 4.2.5 Main Operation Statistic steps of CNO2 for WiMAX Section1 Network Simulation Introduction 1.1 Overview of network simulation 1.2 Network Simulation basics 1.2.1 Digital Map 1.2.2 Universal Transverse Mercator (UTM) 1.3 Wireless Propagation Scenarios Definition 1.4 Model Selection Section2 Propagation Model Tuning 2.1 Data Collection 2.2 Data Processing 2.3 Data Analysis 2.4 Assessment Precision Section3 Simulation Flow 3.1 Data Preparation 3.2 Path Loss Prediction 3.3 Traffic Distribution Creation 3.4 Wireless Network
15
15
15
38
Certification Document of ZTE Skill Center Percentage of Test Questions for ZTE Employees Percentage of Test Questions for Outsourcing Parties Percentage of Test Questions for Customers
I D
Knowledge Points Detail Simulation Analysis 3.5 Outputting Network Simulation Design Report Section4 Quality Assessment on Wireless Network Simulation Design 4.1 Acquiring Network Performance Data 4.2 Comparison Analysis 4.3 Deduction on Network Simulation Quality Section5 Simulation in Network Planning and Optimization 5.1 Network Topology Design 5.2 Network KPI Prediction 5.3 Capacity Expansion and Coverage Issue Section6 Static Simulation Algorithm 6.1 Effective Site Antenna Height Calculation Methods 6.2 Diffraction Loss Calculation (Knife Edge) Techniques 6.3 Giovaneli Diffraction Loss Technique
39