0 оценок0% нашли этот документ полезным (0 голосов)
196 просмотров5 страниц
This document describes the automatic operation function of a CNC machine that allows programs stored on a memory card to be executed. There are two methods: (1) programs can be read from the memory card and run automatically once cycle start is triggered, like using a floppy disk; (2) subprograms stored on the memory card can be called and executed from the main program using a subprogram call command. Parameters must be set correctly to enable the memory card interface. Instructions are provided on selecting and running files from the memory card for DNC operation.
This document describes the automatic operation function of a CNC machine that allows programs stored on a memory card to be executed. There are two methods: (1) programs can be read from the memory card and run automatically once cycle start is triggered, like using a floppy disk; (2) subprograms stored on the memory card can be called and executed from the main program using a subprogram call command. Parameters must be set correctly to enable the memory card interface. Instructions are provided on selecting and running files from the memory card for DNC operation.
Авторское право:
Attribution Non-Commercial (BY-NC)
Доступные форматы
Скачайте в формате PDF, TXT или читайте онлайн в Scribd
This document describes the automatic operation function of a CNC machine that allows programs stored on a memory card to be executed. There are two methods: (1) programs can be read from the memory card and run automatically once cycle start is triggered, like using a floppy disk; (2) subprograms stored on the memory card can be called and executed from the main program using a subprogram call command. Parameters must be set correctly to enable the memory card interface. Instructions are provided on selecting and running files from the memory card for DNC operation.
Авторское право:
Attribution Non-Commercial (BY-NC)
Доступные форматы
Скачайте в формате PDF, TXT или читайте онлайн в Scribd
4, AUTOMATIC OPERATION
OPERATION B-64124ENOT
4.10
DNC OPERATION
WITH MEMORY
CARD
4.10.4
Specification
“DNC operation with Memory Card” is a function that it is possible to
perform machining with executing the program in the memory card,
which is assembled to the memory card interface, where is the left side
of the sei
this function as follows.
(a)By starting automatic operation (cycle start) during the DNC
‘operation mode (RMT), it is possible to perform machining (DNC
operation) while a program is being read from a memory card, as by
There are two methods to us
using the external input/output unit such asa floppy cassette and so on.
(Fig. 4.10.1 (a)
(b)It is possible to read subprograms written in the memory card and
‘execute them by the command Subprogram call (M198). (Fig. 4.10.1
(b)
Memory in CNC
(Program)
Itis possible to do the DNC
‘operation with Memory cara
instead of the normal memory
Memory Card
(Program)
Normal Memory
‘operation by memory in the CNC.
DNC operation
operation by with Memory
memory in the card
enc
Execution of programs
Fig. 4.10.4 (a)
Itis possible to execute the
Memory in CNC Memory Card Eubpregram nthe memory card
(Program) (Sub Program) during memory operation
Normal Memory NN. ‘Subprogram
‘operation by memory. Call (M198)
inthe CNC.
Execution of programs
Fig. 4.10.4 (b)
— sos —BH 124ENI01
OPERATION 4, AUTOMATIC OPERATION
NOTE
To use this function, it is necessary to set the parameter of
No.20 to 4 by setting screen.
No.20 [/O CHANEL: Setting to select an input/output unit]
Setting value is 4: It means using the memory card
interface.
4.10.2
Operations
4.10.2.4
DNC Operation
Procedure
Please set the parameter of No,0020 to 4 in the setting sereen in advance.
(1)Change to RMT mode.
(2)Push [PROG] function key.
(3)Push [ > ] soft key (continuance menu).
(4)When [DNC-CD] soft key is pushed, the following screen is
displayed
(5)The screen can be scrolled by page key. An arbitrary file number is
ut, and [F SRH] soft key is pushed. Then the arbitrary file name
is displayed at the top of DNC operation (memory card) sereen.
(6) When the file number that is exccuted is input and the [DNC-ST] soft
key is pushed, the file name that is selected is set to DNC FILE,
(7) When the cycle start is done, the program that is selected is executed.
DNC OPPRATTON (M CARD) ovaa1 Noaoo1
— 509 —4, AUTOMATIC OPERATION
OPERATION B-64124ENOT
4.10.2.2
Subprogram Call (M198)
Format
Explanation
When the following block in a program in CNC memory is executed, a
subprogram file in memory card is called
1. Normal format
M198 POOOO Aaaa
File number for a file in
the memory card
Number of repetition
Memory card call instruction
2. FS15 tape format
M198
LAAAA
tte number ot peton
File number for a file In the
memory card
Memory card call instruction
Both format 1 and 2 can be used. A different M code can be used for a
subprogram call depending on the setting of parameter No. 6030. In this,
case, MI98 is executed as a normal M code. The file number is specified
ataddress. Ifthe SBP (bit) of parameter No. 3404 is set to 1,a program
number can be specified. When a file number is specified at address P,
Fxxxx is indicated instead of Oxxxx.
NOTE
Please set the parameter of No. 0020 to 4 in the setting
screen in advance.
— slo —BH 124ENI01 OPERATION 4, AUTOMATIC OPERATION
4.10.3 (1) The memory cand can not be accessed, such as display of memory card
Limitation and Notes list and so on, during the DNC operation with memory card.
(2) The selection of DNC operation file that is set at DNC OPERATION
screen is cleared by the power supply turn off and on. Afierthe power
supply is turned on again, itis necessary to select the DNC operation
file again,
(3)Please do not pull out and insert memory card during the DNC
‘operation with memory card,
(4)It is not possible to call a program in the memory card from the DNC.
‘operation program.
(5) When this function is used, secure the memory card by following the
procedure described later, to prevent the card from becoming
disconnected or poorly connected due to vibration during operation or
for some other reason.
4.10.4
Parameter ww ss wt
ors] [oNir
[Data type} Bit
#7(DNM) The DNC operation with memory card function is
0: disable
1 enable.
4.10.5 Follow the procedure below to fix the memory card.
Procedure for Fixing 1. Inserting the memory card into the fixing bracket,
the Memory Card
Fix the card at this point
Insertthe memory card ntothe Fix the memory card tothe fixing
{xing bracket in the direction bracket
indicated by the arrow.
— si4, AUTOMATIC OPERATION OPERATION B-64124ENOT
2. Inserting the card into the PCMCIA port.
Loosen the screw of the
fixing bracket and insert
the memory card into the
PCMCIA port with the
claw ofthe fixing bracket
raised.
‘Align the claw with the groove.
‘Align the claw ofthe fixing bracket
with the groove ofthe PCMCIA port
and then push the bracket in the
direction indicated by the arrow.
Push the bracket to the right
Tighten the screw ofthe bracket
to fx the memory card,
Fix the card by tightening the screw.
— siz —