Академический Документы
Профессиональный Документы
Культура Документы
REMOVAL
CAUTION: Work must be started more than 90 seconds after the ignition switch is turned into the LOCK position and the negative (-) terminal cable is disconnected from the battery. The SRS is equipped with a back-up power source. If work is started within 90 seconds from disconnecting the negative (- ) terminal cable of the battery, the SRS may be deployed. HINT: A bolt without a torque specification is shown in the standard bolt chart. (see page SS-2 )
Cover
1. REMOVE CENTER CLUSTER FINISH PANEL (a) Using a screwdriver, pry out the cover. HINT: Tape the screwdriver tip before use.
H22781
(b) (c)
Remove the 2 screws. Using a screwdriver, disengage the 4 clips and remove the center cluster finish panel.
HINT: Tape the screwdriver tip before use. (d) w/ LEXUS navigation system: Disconnect the connectors.
4 Clips
H22782
2. (a)
REMOVE LOWER CENTER CLUSTER FINISH PANEL Using a screwdriver, disengage the 2 clips and remove the lower center cluster finish panel.
HINT: Tape the screwdriver tip before use. (b) Disconnect the connectors.
2 Clips
2005 LEXUS IS300 (RM1140U)
H15130
Author :
Date :
2376
BO-140
BODY INSTRUMENT PANEL
3. (a) (b)
REMOVE A/C CONTROL WITH RADIO RECEIVER ASSEMBLY Remove the 4 bolts and A/C control with radio receiver assembly. Disconnect the connectors.
H15131
4. (a) (b)
REMOVE UPPER CONSOLE PANEL M/T: Remove the shift lever knob. Using a screwdriver, disengage the 2 clips and remove the upper console panel as shown in the illustration.
HINT: Tape the screwdriver tip before use. (c) Disconnect the connector.
2 Clips
H19273
5. REMOVE PARKING BRAKE HOLE COVER Using a screwdriver, disengage the 2 clips and remove the parking brake hole cover. HINT: Tape the screwdriver tip before use.
2 Clips
H15133
w/o Arm rest: REMOVE CONSOLE BOX Remove the 6 screws. w/o LEXUS navigation system: Pull the console box rearward to remove it. w/ LEXUS navigation system: Pull the console box rearward to remove it, then disconnect the connector.
H15134
7. (a)
w/ Arm rest: REMOVE CONSOLE BOX Using a screwdriver, disengage the 3 claws and remove the box side No. 1 and No. 2 panels.
3 Claws
2005 LEXUS IS300 (RM1140U)
H22783
Author :
Date :
2377
BO-141
BODY INSTRUMENT PANEL
(b)
Remove the 2 bolts and remove the console compartment door. Torque:30 Nm (306 kgfcm, 22 ftlbf.)
H22935
(c)
H22934
(g)
H19279
Remove the 6 screws. w/o LEXUS navigation system: Pull the console box rearward to remove it. w/ LEXUS navigation system: Pull the console box rearward to remove it, then disconnect the connector. Remove the 4 bolts and rear console armrest hinge.
8. DISCONNECT PASSENGER AIRBAG CONNECTOR (a) Using a clip remover, disengage the connector clamp. (b) Disconnect the passenger airbag connector. NOTICE: When disconnecting the airbag connector, take care not to damage the airbag wire harness.
H15685
9. REMOVE GLOVE COMPARTMENT DOOR Disconnect the hinge shaft and remove the glove compartment door.
H15136
Author :
Date :
2378
BO-142
BODY INSTRUMENT PANEL
H15137
10. REMOVE FRONT PASSENGER AIRBAG ASSEMBLY Remove the 2 bolts, 2 nuts and the passenger airbag assembly from the instrument panel. Torque: 20 Nm (205 kgfcm, 15 ftlbf.) for bolt 5.5 Nm (56 kgfcm, 49 in.lbf) for nut CAUTION: S Do not store the front passenger airbag assembly with the airbag deployment side facing down. S Never disassemble the front passenger airbag assembly. 11. REMOVE STEERING WHEEL PAD (See page SR-13 ) 12. REMOVE STEERING WHEEL (See page SR-13 ) 13. REMOVE COLUMN UPPER AND LOWER COVERS (See page SR-13 ) 14. REMOVE SPIRAL CABLE (See page SR-13 )
REMOVE LOWER FINISH PANEL Remove the 3 screws. Using a screwdriver, disengage the 3 clips and remove the lower finish panel.
HINT: Tape the screwdriver tip before use. (c) Disconnect the connectors and hood lock control cable.
3 Clips
H23154
REMOVE CLUSTER FINISH PANEL Remove the 2 screws. Using a screwdriver, disengage the 4 clips and remove the cluster finish panel.
4 Clips
H15715
REMOVE COMBINATION METER Remove the 3 screws and combination meter. Disconnect the connector.
H15716
Author :
Date :
2379
BO-143
BODY INSTRUMENT PANEL
18. (a)
REMOVE FRONT DOOR INSIDE SCUFF PLATE LH Using a screwdriver, disengage the 5 clips and remove the front door inside scuff plate.
HINT: Tape the screwdriver tip before use. 19. REMOVE FRONT DOOR INSIDE SCUFF PLATE RH HINT: Use the same procedures described for the LH side.
5 Clips
H23155
20. REMOVE COWL SIDE TRIM BOARD LH (a) Remove the clip. (b) Pull the cowl side trim board rearward to remove it. 21. REMOVE COWL SIDE TRIM BOARD RH HINT: Use the same procedures described for the LH side. 22. REMOVE FRONT PART OF FRONT DOOR OPENING TRIMS
H15718
23. REMOVE FRONT PILLAR GARNISH LH (a) Using a screwdriver, remove the pillar garnish cover. (b) Remove the bolt. (c) Using a screwdriver, remove the pillar garnish. HINT: Tape the screwdriver tip before use. (d) Remove the bolt. Torque: 9.8 Nm (100 kgfcm, 87in.lbf)
Clip
H19277
(e)
24. HINT: Use the same procedures described for the LH side.
Cover the airbag with protective cover as shown in the illustration.. REMOVE FRONT PILLAR GARNISH RH
H19278
Author :
Date :
2380
BO-144
BODY INSTRUMENT PANEL
25. REMOVE INSTRUMENT PANEL (a) Disconnect the connectors. (b) Disengage the wire harness clamps. (c) Remove the 3 bolts, 2 screws and 2 nuts. (d) Pull the instrument panel rearward to remove it. NOTICE: Be careful not to damage the instrument panel and wire harness
H15720
Author :
Date :
2381
BO-145
BODY INSTRUMENT PANEL
REMOVE INSTRUMENT PANEL REINFORCEMENT Disengage the wire harness clamps. Remove the bolt<F> and ground cable. Remove the 2 bolts <A> and LH lower pad insert. Remove the bolt<B>, screw<B> and No. 1 mounting bracket. (e) Remove the bolt<C> and panel to floor brace. (f) Remove the bolt<D> and No. 2 mounting bracket. (g) Remove the 4 bolts<E> and No. 1 brace. (h) Remove the 5 bolts, 2 nuts, instrument panel reinforcement and the lower mounting bracket. NOTICE: Be careful not to damage the body and wire harness.
H19472
<F> <D> No. 2 Mounting Bracket <E> <C> <A> LH Lower Pad Insert No. 1 Brace Panel to Floor Brace Lower Molding Bracket
H23169
Author :
Date :
2382