Академический Документы
Профессиональный Документы
Культура Документы
Page 1 of 8
Lathes
Vea esta pgina en Espaol
PL-4 Bench Lathe 165 mm centre height 175, 215, 250 & 254 Series Geared Head Lathes 175 to 300 mm centre height
"Manek" All Geared Lathe 200 mm centre height Heavy Duty Geared Head Lathe 375 mm centre height Single Spindle Automatic Lathes
"HMTL" All Geared Lathe 200 and 250 mm centre height Capstan Lathes
Bench Lathe
- Close grained ground alloyed Cast Iron bed with hardness of 190 - 200 BH. - Totally enclosed dial type Gear Box with hardened and ground shafts running in Ball Bearing. - Spindles and Shafts ground and wearable parts standardized for interchangeability.
Model: Length / Width of Bed (mm): Centre Height (mm): Admit between Centres (mm): Swing over Bed, Gap, Cross-Slide (mm): Spindle Bore (mm): 16 Speeds Spindle - Speed Range (RPM): MT-2 bored Tail Stock barrel travel (mm): Cross and Compound Slide Travel (mm): Longitudinal Feed Range per spindle rev.: Cross Feed Range per spindle rev.: 36 Pitches Range Whitworth Threads (TPI): 12 Pitches Range Metric Threads (mm): Lead Screw Diameter and Pitch: Motor: * Cabinet type Steel Stand & Tray seen above are Optional Accessories Standard Accessories: 1 HP Motor and Switch, 3-Jaw True Chuck (165 mm) with back Plate, 4 - Jaw Dog Chuck (200 mm) with back Plate, Face and Centre Plates, 2 Centres, 2 Pt. traveling guide, threading dial and chart. Optional Accessories: Taper Turning Attachment, Spot Lamp, Cabinet Type Steel Stand with Tray, 3 Point fixed Guide, Motorized Coolant Pump with Tank and fittings. Gross Weight (Kgs.): Bench Type: Lathe with Cabinet Stand: Shipping Dimensions Bench Type: Lathe with Cabinet Stand: Shipping Volume (m3): Bench Type: Lathe with Cabinet Stand:
PL - 4 1309 / 200 165 700 315, 430, 175 35 43 - 1045 120 200 - 90 0.002" - 0.031" 0.0005" - 0.007" 4 to 60 0.5 to 6.0 1", 4 TPI 1 HP 400 600 66" x 30" x 24" 66" x 30" x 48" 0.786 1.572
http://maneklalexports.com/English/McTools/Lathes.htm
9/9/2009
lathe, bench type, belt driven type, all geared type, high precision type, capstan, single spi... Page 2 of 8
Type of spindle nose: Size of spindle nose (mm): Spindle bore (mm): Taper bore in centre adopter: Tail stock spindle diameter (mm): Tail stock MT: Tail stock spindle travel (mm): Travel of top slide (mm): Tool shank section (mm): Lead screw diameter (mm): Lead screw thread (TPI): No. of speeds / range (rpm): No. of feeds / range (mm / rev) Longitudinal: Cross: Metric threads (nos. / mm pitch): Inch threads (nos. / TPI): Electric motor (HP): Net / Gross weight (Kgs.): Overall dimensions (m): Shipping volume (m3):
32 / 0.06-1.00 32 / 0.06-0.241 16 / 0.5 to 4 32 / 4 to 60 2 Optional Accessories: Taper turning attachment, revolving centre MT-4 950 / 1100 2.3 x 0.9 x 1.2 2.5 Standard Accessories: Electric Motor, reversible switch, 3 and 4 jaw chuck, coolant pump, machine lamp, 02 nos. dead centre, chuck plate, face plate, steady rest and follow rest.
http://maneklalexports.com/English/McTools/Lathes.htm
9/9/2009
lathe, bench type, belt driven type, all geared type, high precision type, capstan, single spi... Page 3 of 8
Geared Head Precision Lathe - 175, 215, 250 & 254 Series
- Spindle Cam lock type D1 - 4 Hardened & Ground - Head stock gears, splines Hardened, Ground and Profile Ground - Head stock Lubricated by a built in Oil pump - Carriage, Surface Slide, Compound Slide & Tail Stock base of 25 Grad Casting, duly Stress Relieved - Taper Wages are of S. G. Iron in Surface slide & Compound slide - Apron Gears are Nitrated and made from EN 8 Material - Feed Box Gears are of EN 24 Material with Toughening Process - Four Position Tool Post with Heat treated Bolts - Tail Stock Spindle Hardened, Ground, Graduated on Outer Diameter with L. C. - End Gear train gears of 25 Graded Casting with bearing type Idler gear - Surface nut with Backlash Eliminator - All Dial Rings Hard chromed and least count Graduated. - Single Grounded Rack and Hardened & Ground Pinion - 2000 RPM in Spindle with two Speed Motor - All Screws made on CNC Turning Centers (Lead screw, Cross Slide screw, Compound Slide screw, Tail Stock screw) - Spindle instant stop electro plugging brake
Model: 175 / 750 Model: Capacity Height of Centre (mm): Swing over Bed (mm): Swing over Cross Slide (mm): Distance Between Centres (mm): Max. Swing in Gap (mm): Bed Bed Type: Bed Width (mm): Length of Gap in front of Face Plate (mm): Headstock Number of Spindle Speeds: Spindle Speeds Range (rpm): Type and Size of Spindle Nose: Spindle Bore (mm): Spindle Morse Taper Number: Diameter of Front Bearing (mm): Tailstock Spindle Diameter (mm): Spindle Morse Taper Number: Spindle Travel (mm): Lateral Movement of Tailstock (mm): Saddle Cross-slide Travel (mm): Cross-slide Dimensions (mm): Compound Slide Traverse (mm): Saddle Traverse (mm): Tool Shank Section (mm): Feeds and Threads Number of Feeds: 175 175 340 176 750 / 1000 620 2V & 2 Flat 280 160 8 54 to 1200 Cam lock size D1- 4 40 MT-5 110 x 60 50.8 MT-3 175 5 225 178 x 415 130 640 / 890 22 x 22 72 215 215 420 250 1000 / 1500 700 2V & 2 Flat 280 160 8 54 to 1200
Model: 215 / 1000 250 250 500 290 1000 / 1500 770 2V & 2 Flat 355 240 18 32 to 1650 Cam lock size 6 55 MT-6 150 x 85 57.15 4 200 5 325 550 x 200 150 890 / 1390 25 x 25 76 254 254 490 300 1000 / 1500 / 2000 / 2500 / 3000 800 2V & 2 Flat 325 175 8 30 to 1230 Cam lock size 6 52 MT-6 140 x 80 57.15 4 200 5 325 445 x 200 150 -25 x 25 72
Cam lock size D1- 4 40 MT-5 110 x 60 50.8 MT-3 175 5 225 178 x 415 130 890 / 1390 25 x 25 76
http://maneklalexports.com/English/McTools/Lathes.htm
9/9/2009
lathe, bench type, belt driven type, all geared type, high precision type, capstan, single spi... Page 4 of 8
Range of Longitudinal Feeds (mm/rev.): Range of Cross Feeds (mm / rev.): Number of Threads: Metric Range (number): Inch Range (number): D.P. Range (number): Module Range (number): Lead Screw Diameter (mm): Lead Screw Pitch (mm): Electricals Main Motor (kW):
0.033 to 0.468 0.021 to 0.301 103 0.2 to 6.5 mm (31) 72 to 4 TPI (36) 44 to 8 DP (21) 0.4 - 3.0 MOD (15) 31.75 6 1.5
0.026 to 0.936 0.016 to 0.620 106 0.2 to 7.0 mm (33) 72 to 4 TPI (36) 44 to 8 DP (21) 0.3 - 3.0 MOD (16) 31.75 6 2.25
0.45 to 1.600 0.003 to 0.128 106 0.2 to 7.0 mm (33) 72 to 4 TPI (36) 44 to 8 DP (21) 0.3 - 3.0 MOD (16) 31.75 6 3.75
0.45 to 1.600 0.003 to 0.128 103 0.2 to 6.5 mm (31) 72 to 4 TPI (36) 44 to 8 DP (21) 0.4 - 3.0 MOD (15) 38.1 6 2.25
Model 175 / 750 175 / 1000 215 / 1000 215 / 1500 250 / 1000 250 / 1500 254 / 1000 254 / 1500 254 / 2000 254 / 2500 254 / 3000
Net Weight (kgs) 800 1000 1200 1300 1500 1800 1500 1850 2250 2400 2550
Gross Weight (kgs) 1000 1200 1400 1500 1700 2100 1775 2150 2550 2800 2900
Case Dimensions (m) 2.1 x 1.0 x 1.3 2.3 x 1.0 x 1.3 2.3 x 1.0 x 1.5 3.0 x 1.0 x 1.5 2.8 x 1.0 x 1.5 3.3 x 1.0 x 1.5 2.7 x 1.1 x 1.4 3.2 x 1.1 x 1.5 3.8 x 1.1 x 1.5 4.3 x 1.1 x 1.5 4.8 x 1.1 x 1.5
Shipping Volume (m3) 2.70 3.00 3.50 4.50 4.20 5.00 4.20 5.30 6.30 7.10 8.00
Standard Accessories: Four Position Tool Post, Toolpost Spanner, Chuck Plate, Face Plate, Centre Adapter, 2 x Dead Centres, Electric Motor with Electrical Controls, Thread Dial Indicator, Steady Rest, Follow Rest, Chip Tray, 3 & 4 Jaw Chucks, Coolant Pump, Machine Lamp With model 175, 215 & 250 only: Carrier Plate, Rear Splash Guard & Mechanical Brake Optional Accessories: Quick Change Tool Post, Taper Turning Attachment, Rear Tool Post, Keyway cutting attachment, Tool Post Grinder with 8" Grinding Wheel and electricals With Model 254 only: 12" Centre Height in lieu of the standard
http://maneklalexports.com/English/McTools/Lathes.htm
9/9/2009
lathe, bench type, belt driven type, all geared type, high precision type, capstan, single spi... Page 5 of 8
- Geared Head Heavy Duty Lathe with Norton Gearbox - Flame Hardned Bed - Model GH-12 lathe with Cabinet Stand - All other models with Planner Type Bed
Model: Centre height (mm): Admit between centres (mm): Width of bed (mm): Spindle bore (mm): Swing over bed (mm): Swing in gap (mm): Width of gap in front of faceplate (mm): Swing over cross slide (mm): Thread range (mm): Thread range TPI (Inches): Lead screw (TPI): Number of Speed / Range (no / rpm): Power requirement (HP): Model: GH-16 with Planner type stand Net / Gross weight (kgs.): Overall Dimensions (m): Approximate Shipping
GH-12 375 2000 450 104 750 1050 575 475 0.5 - 7.5 4 - 60 4 8 / 15 400 5 3100 / 3400
GH-14 375 2500 450 104 750 1050 575 475 0.5 - 7.5 4 - 60 4 8 / 15 400 5 3400 / 3800
GH-16 375 3000 450 104 750 1050 575 475 0.5 - 7.5 4 - 60 4 8 / 15 400 5 3800 / 4200
GH-20 375 4000 450 104 750 1050 575 475 0.5 - 7.5 4 - 60 4 8 / 15 400 5 4800 / 5300
4.2 x 1.2 x 4.8 x 1.2 x 5.4 x 1.2 x 6.0 x 1.2 x 1.35 1.35 1.35 1.35
http://maneklalexports.com/English/McTools/Lathes.htm
9/9/2009
lathe, bench type, belt driven type, all geared type, high precision type, capstan, single spi... Page 6 of 8
Volume (m3):
6.8
7.8
8.8
9.8
Standard Accessories: Face plate, Drive plate, Steady rest, Follow rest, Thread dial indicator, 4way tool post, one M.T. centre, 3 and 4 Jaw chuck, suitable motor with control panel, coolant pump and machine lamp. Optional Accessories: Taper Turning Attachment (Can be supplied only if ordered with the Lathe)
Capstan Lathes
Model: Maximum Bar Turning Cap. (mm): Height of Centre (mm): Swing over bed (mm): Swing over cross slide (mm): Chucking Diameter of Chuck (mm): Max. distance between Spindle Face and Turret Head (mm): Number of Spindle Speeds: Range of Spindle Speeds (RPM): Max. useful stroke of Capstan Slide (mm): Cross Slide Movements (mm): Diameter of Holes in Turret (mm): Length x Width of Bed (mm): Approximate Net / Gross weight (kgs.): Approximate Shipping Dimensions (mm): Approximate Shipping Volume (m3): PC-25 25 165 300 165 165 275 3 650 - 1660 95 110 25.4 900 x 165 750 / 900 1350x765x1400 1.45 Standard Accessories: Collet attachment with one Collet, Three step Spindle Pulley bar feed, Toolbox, 2 HP Motor and Reversible Switch Optional Accessories: Norton Gearbox, Feed for Turret Slide, Panel Board Model: PC-25 with feed for Turret Slide (Optional) 25 mm capacity Capstan Lathe with 3 step spindle pulley
Model: Maximum Bar Turning Cap. (mm): Height of Centre (mm): Swing over bed (mm): Swing over cross slide (mm): Chucking Diameter of Chuck (mm): Max. distance between Spindle Face and Turret Head (mm): Number of Spindle Speeds: Range of Spindle Speeds (RPM): Max. useful stroke of Capstan Slide (mm): Cross Slide Movements (mm): Diameter of Holes in Turret (mm): Model: PC-32: 32 mm capacity Capstan Lathe available with and without Full Norton gearbox Standard Accessories: Collet attachment with one Collet, Toolbox, 2 HP Motor and Reversible Switch and Coolant Pump Length x Width of Bed (mm): Approximate Net / Gross weight (kgs.): Approximate Shipping Dimensions (mm):
PC-32 32 165 300 165 165 500 6 162 - 1500 95 200 25.4 1200 x 180 1200 / 1500 1650x900x1450
http://maneklalexports.com/English/McTools/Lathes.htm
9/9/2009
lathe, bench type, belt driven type, all geared type, high precision type, capstan, single spi... Page 7 of 8
Optional Accessories: Full Norton Gearbox with Self Shaft, Feed for Turret Slide, Pipe Bar Feed attachment, Panel Board
2.20
Model: Maximum Bar Turning Cap. (mm): Height of Centre (mm): Swing over bed (mm): Swing over cross slide (mm): Chucking Diameter of Chuck (mm): Max. distance between Spindle Face and Turret Head (mm): Number of Spindle Speeds: Range of Spindle Speeds (RPM): Max. useful stroke of Capstan Slide (mm): Cross Slide Movements (mm): Diameter of Holes in Turret (mm): Length x Width of Bed (mm): Approximate Net / Gross weight (kgs.): Approximate Shipping Dimensions (mm): Approximate Shipping Volume (m3):
PC-40 40 190 400 200 200 560 12 98 - 1040 200 250 32 1400 x 230 1800 / 2200 1800x1100x1500 3.00 Standard Accessories: Collet attachment with one Collet, Toolbox, 3 HP Motor, Panel Board, Pipe Bar feed Attachment, Automatic Feed for Cross Slide and Turret Slide by Self Shaft and Coolant Pump Model: PC-40: 40 mm capacity All Geared Capstan Lathe with Full Norton gearbox and 12 speeds
Model: Maximum Cap.: Round Hexagon Square Stroke of cross slide: Max. capacity of Tailstock Collect: Max. tailstock travel: Spindle Speeds (12 steps): Production Rate: Cycle Time: Maximum Turning Length (with longitudinal turning slide): Work Spindle Motor: Feed Drive Motor: Approximate Net / Gross weight: Approximate Dimensions: Model: D-25 Approximate Shipping Volume:
D-25 25 mm 22 mm 18 mm 22 mm 13 mm 100 mm 550 to 4000 rpm 28 to 2100 pcs/hr 1.71 sec/pc / 128.6 sec/pc 70 mm 1.3 / 1.6 kW 0.37 kW 850 / 1100 kgs. 1.65 x 1.00 x 1.80 m & 4.10 x 0.13 x 0.13 m 3.10 m3
Standard Accessories: Complete electrical equipment, bar feeding attachment, bar feed pipe, double vertical slide, single open tool holder front & rear, automatic electric shutter and a set of service tools Optional Accessories: Longitudinal Turning Attachment front, step turning tool holder, Collets - metric round (range 4 to 25 mm in steps of 0.5 mm), Drill Collets metric (range 3 to 13 mm in steps of 0.5 mm)
http://maneklalexports.com/English/McTools/Lathes.htm
9/9/2009
lathe, bench type, belt driven type, all geared type, high precision type, capstan, single spi... Page 8 of 8
http://maneklalexports.com/English/McTools/Lathes.htm
9/9/2009