Вы находитесь на странице: 1из 190

ITCC

IT01-03, KB04-06 and RD03-04

APPENDIX

PROJECT No. J09-07800 October 2010

APPENDIX A: BUILDING MANAGEMENT SYSTEM (PLUMBING INPUT/OUTPUT LISTS)

ITCC in Riyadh Bldg KB04-KB06, IT01-IT03 & RD03-RD04 J09-07800

Divider

Project : ITCC- Building KB04 (Main Building) Subject : BMS Input / Output List - Plumbing & Fire Protection Item Qty. Point Description
Plumbing and Fire Protection Equipments In-line Electric Driven Fire Pumps (1-Duty) in basement 1 2 3 4 5 6 7 1 Pump On/Off Status Water flow status Pump Trip Alarm Pump Auto / Manual Status Pump Start/stop command Discharge header pressure Pump motor temperature high TOTAL Total Electric Driven Fire Pump Points Total Electric Driven Fire Pump Points Sump Pumps (1-Duty & 1-Lag each) [Ref.: SP-1,2,3] - 3 nos. Lift Sta. in basement 1 2 3 4 5 6 6 Pump on/off Status Pump Trip Status Pressure in the Common Discharge Header Pump Auto / Manual Status Run time meter reading (no input) Sump High & Low Level Total per Unit Total for all Units Total Sump Pumps Points 1 3 1 1 1 2 2

AI

Note: Fire Protection Control with Fire Alarm Panel BACnet Required Points Software Network OPC Client DI AO DO Thermostat Integration

Remarks

1 1 1 1 1

From Pump Control Panel Flow switch From Pump Control Panel From Pump Control Panel Relay Output From BMS Liquid pressure sensor From Pump Control Panel

4 4 7

0 0

1 1

2 1 1 2 2 6 36 51 0 0 2 12

From Pump Control Panel From Pump Control Panel Liquid Pressure Sensor From Pump Control Panel Vertual sensor with BMS From Tank Float Switch

1 of 2

Project : ITCC- Building KB04 (Main Building) Subject : BMS Input / Output List - Plumbing & Fire Protection Item Qty. Point Description
Diesel Fuel Transfer Pumps + Bulk Storage Tank [1-Duty ] -1 set 1 2 3 4 5 6 7 8 9 10 11 12 1 Pump On/Off Status Fuel flow status Pump Trip Alarm Pump Auto / Manual Status Pump Start/stop command Discharge header pressure switch Discharge header pressure Pump motor temperature high Bulk Storage Tank Fuel Level Bulk Storage Tank Low Level Alarm Day Tank Low Level Alarm Day Tank Fuel Level Total per Unit Total for all Units 2 2 1 1

AI

Note: Fire Protection Control with Fire Alarm Panel BACnet Required Points Software Network OPC Client DI AO DO Thermostat Integration

Remarks

1 1 1 1 1 1

From Pump Control Panel Flow switch From Pump Control Panel From Pump Control Panel Relay Output From BMS Liquid pressure switch Liquid pressure sensor From Pump Control Panel

1 1 1 1 9 9 12 0 0 1 1

From Pump Control Panel From Pump Control Panel From Pump Control Panel From Pump Control Panel

2 of 2

Project : ITCC- Building KB05(Main Building) Subject : BMS Input / Output List - Plumbing & Fire Protection Item Qty. Point Description
Plumbing and Fire Protection Equipments In-line Electric Driven Fire Pumps (1-Duty) in basement 1 2 3 4 5 6 7 1 Pump On/Off Status Water flow status Pump Trip Alarm Pump Auto / Manual Status Pump Start/stop command Discharge header pressure Pump motor temperature high TOTAL Total Electric Driven Fire Pump Points Total Electric Driven Fire Pump Points Sump Pumps (1-Duty & 1-Lag each) [Ref.: SP-1,2,3] - 3 nos. Lift Sta. in basement 1 2 3 4 5 6 6 Pump on/off Status Pump Trip Status Pressure in the Common Discharge Header Pump Auto / Manual Status Run time meter reading (no input) Sump High & Low Level Total per Unit Total for all Units Total Sump Pumps Points Fountain Pumps (1-Duty & 1-Standby) 1 2 3 4 5 6 7 8 2 Pump On/Off Status Water flow status Pump Trip Alarm Pump Auto / Manual Status Pump Start/stop command Discharge header pressure switch Discharge header pressure Pump motor temperature high TOTAL Total Fountain Pumps Points Total Fountain Pumps Points 1 1 2 1 3 1 1 1 2 2

AI

Note: Fire Protection Control with Fire Alarm Panel BACnet Required Points Software OPC Client Network Integration DI AO DO Thermostat

Remarks

1 1 1 1 1

From Pump Control Panel Flow switch From Pump Control Panel From Pump Control Panel Relay Output From BMS Liquid pressure sensor From Pump Control Panel

4 4 7

0 0

1 1

2 1 1 2 2 6 36 51 0 0 2 12

From Pump Control Panel From Pump Control Panel Liquid Pressure Sensor From Pump Control Panel Vertual sensor with BMS From Tank Float Switch

1 1 1 1 1 1 1 6 12 16 1 of 2 0 0 1 2

From Pump Control Panel Flow switch From Pump Control Panel From Pump Control Panel Relay Output From BMS Liquid pressure switch Liquid pressure sensor From Pump Control Panel

Project : ITCC- Building KB05(Main Building) Subject : BMS Input / Output List - Plumbing & Fire Protection Item Qty. Point Description
Filter Pumps for Fountains (1-Duty & 1-Standby) 1 2 3 4 5 6 7 2 Pump On/Off Status Water flow status Pump Trip Alarm Pump Auto / Manual Status Pump Start/stop command Discharge header pressure switch Pump motor temperature high TOTAL Total Filter Pumps for Fountains Points Total Filter Pumps for Fountains Points Diesel Fuel Transfer Pumps + Bulk Storage Tank [1-Duty ] -1 set 1 2 3 4 5 6 7 8 9 10 11 12 1 Pump On/Off Status Fuel flow status Pump Trip Alarm Pump Auto / Manual Status Pump Start/stop command Discharge header pressure switch Discharge header pressure Pump motor temperature high Bulk Storage Tank Fuel Level Bulk Storage Tank Low Level Alarm Day Tank Low Level Alarm Day Tank Fuel Level Total per Unit Total for all Units 2 2 1 1 1 1 2

AI

Note: Fire Protection Control with Fire Alarm Panel BACnet Required Points Software OPC Client Network Integration DI AO DO Thermostat

Remarks

1 1 1 1 1 1 5 10 14 0 0 1 2

From Pump Control Panel Flow switch From Pump Control Panel From Pump Control Panel Relay Output From BMS Liquid pressure switch From Pump Control Panel

1 1 1 1 1 1

From Pump Control Panel Flow switch From Pump Control Panel From Pump Control Panel Relay Output From BMS Liquid pressure switch Liquid pressure sensor From Pump Control Panel

1 1 1 1 9 9 12 0 0 1 1

From Pump Control Panel From Pump Control Panel From Pump Control Panel From Pump Control Panel

2 of 2

Project : ITCC- Building KB06(Main Building) Subject : BMS Input / Output List - Plumbing & Fire Protection Item Qty. Point Description
Plumbing and Fire Protection Equipments In-line Electric Driven Fire Pumps (1-Duty) in 2nd basement 1 2 3 4 5 6 7 1 Pump On/Off Status Water flow status Pump Trip Alarm Pump Auto / Manual Status Pump Start/stop command Discharge header pressure Pump motor temperature high TOTAL Total Electric Driven Fire Pump Points Total Electric Driven Fire Pump Points 1 1 2 2

AI

Note: Fire Protection Control with Fire Alarm Panel BACnet Required Points Software OPC Client Network Integration DI AO DO Thermostat

Remarks

1 1 1 1 1

From Pump Control Panel Flow switch From Pump Control Panel From Pump Control Panel Relay Output From BMS Liquid pressure sensor From Pump Control Panel

4 4 7

0 0

1 1

Sump Pumps (1-Duty & 1-Lag each) [Ref.: SP-1,2,3,4] - 4 nos. Lift Sta. in basement 1 2 3 4 5 6 8 Pump on/off Status Pump Trip Status Pressure in the Common Discharge Header Pump Auto / Manual Status Run time meter reading (no input) Sump High & Low Level Total per Unit Total for all Units Total Sump Pumps Points Fountain Pumps (1-Duty & 1-Standby) 1 2 3 4 5 6 7 8 2 Pump On/Off Status Water flow status Pump Trip Alarm Pump Auto / Manual Status Pump Start/stop command Discharge header pressure switch Discharge header pressure Pump motor temperature high TOTAL Total Fountain Pumps Points Total Fountain Pumps Points 1 1 2 1 1 6 12 16 1 of 2 0 0 1 2 1 1 1 1 1 From Pump Control Panel Flow switch From Pump Control Panel From Pump Control Panel Relay Output From BMS Liquid pressure switch Liquid pressure sensor From Pump Control Panel 1 3 2 6 48 67 0 0 1 1 2 2 16 2 1 From Pump Control Panel From Pump Control Panel Liquid Pressure Sensor From Pump Control Panel Vertual sensor with BMS From Tank Float Switch

Project : ITCC- Building KB06(Main Building) Subject : BMS Input / Output List - Plumbing & Fire Protection Item Qty. Point Description
Filter Pumps for Fountains (1-Duty & 1-Standby) 1 2 3 4 5 6 7 2 Pump On/Off Status Water flow status Pump Trip Alarm Pump Auto / Manual Status Pump Start/stop command Discharge header pressure switch Pump motor temperature high TOTAL Total Filter Pumps for Fountains Points Total Filter Pumps for Fountains Points Diesel Fuel Transfer Pumps + Bulk Storage Tank [1-Duty ] -1 set 1 2 3 4 5 6 7 8 9 10 11 12 1 Pump On/Off Status Fuel flow status Pump Trip Alarm Pump Auto / Manual Status Pump Start/stop command Discharge header pressure switch Discharge header pressure Pump motor temperature high Bulk Storage Tank Fuel Level Bulk Storage Tank Low Level Alarm Day Tank Low Level Alarm Day Tank Fuel Level Total per Unit Total for all Units 2 2 1 1 1 1 2

AI

Note: Fire Protection Control with Fire Alarm Panel BACnet Required Points Software OPC Client Network Integration DI AO DO Thermostat

Remarks

1 1 1 1 1 1 5 10 14 0 0 1 2

From Pump Control Panel Flow switch From Pump Control Panel From Pump Control Panel Relay Output From BMS Liquid pressure switch From Pump Control Panel

1 1 1 1 1 1

From Pump Control Panel Flow switch From Pump Control Panel From Pump Control Panel Relay Output From BMS Liquid pressure switch Liquid pressure sensor From Pump Control Panel

1 1 1 1 9 9 12 0 0 1 1

From Pump Control Panel From Pump Control Panel From Pump Control Panel From Pump Control Panel

2 of 2

Project : ITCC- Building RD-03(Main Building) Subject : BMS Input / Output List - Plumbing & Fire Protection Item Qty. Point Description
Plumbing and Fire Protection Equipments In-line Electric Driven Fire Pumps (1-Duty) in 4th basement 1 2 3 4 5 6 7 1 Pump On/Off Status Water flow status Pump Trip Alarm Pump Auto / Manual Status Pump Start/stop command Discharge header pressure Pump motor temperature high TOTAL Total Electric Driven Fire Pump Points Total Electric Driven Fire Pump Points 1 1 2 2

AI

Note: Fire Protection Control with Fire Alarm Panel BACnet Required Points Software Network OPC Client DI AO DO Thermostat Integration

Remarks

1 1 1 1 1

From Pump Control Panel Flow switch From Pump Control Panel From Pump Control Panel Relay Output From BMS Liquid pressure sensor From Pump Control Panel

4 4 7

0 0

1 1

Sump Pumps (1-Duty & 1-Lag each) [Ref.: SP-1,2,3,4,5] - 5 nos. Lift Sta. in basement 1 2 3 4 5 6 10 Pump on/off Status Pump Trip Status Pressure in the Common Discharge Header Pump Auto / Manual Status Run time meter reading (no input) Sump High & Low Level Total per Unit Total for all Units Total Sump Pumps Points Non-Potable Water Pumps (1-Duty&1-Standby) [Ref. No.: DP-1,2] 1 2 3 4 5 6 7 8 2 Pump On/Off Status Water flow status Pump Trip Alarm Pump Auto / Manual Status Pump Start/stop command Discharge header pressure Run time meter reading (no input) Pump motor temperature high TOTAL Total Potable Water Pumps Points Total Potable Water Pumps Points 1 2 3 4 8 19 0 0 1 3 4 8 1 1 1 1 1 VFC From Pump Control Panel Flow switch VFC From Pump Control Panel VFC From Pump Control Panel Relay Output From BMS Liquid pressure sensor Vertual sensor with BMS From Pump Control Panel 1 3 2 6 60 83 0 0 1 1 2 2 20 2 1 From Pump Control Panel From Pump Control Panel Liquid Pressure Sensor From Pump Control Panel Vertual sensor with BMS From Tank Float Switch

1 of 2

Project : ITCC- Building RD-03(Main Building) Subject : BMS Input / Output List - Plumbing & Fire Protection Item Qty.
1 2 3 4 5 6 7 8 9 10 11 12 1 Pump On/Off Status Fuel flow status Pump Trip Alarm Pump Auto / Manual Status Pump Start/stop command Discharge header pressure switch Discharge header pressure Pump motor temperature high Bulk Storage Tank Fuel Level Bulk Storage Tank Low Level Alarm Day Tank Low Level Alarm Day Tank Fuel Level Total per Unit Total for all Units 2 2 1 1

Point Description
Diesel Fuel Transfer Pumps + Bulk Storage Tank [1-Duty ] -1 set

AI

Note: Fire Protection Control with Fire Alarm Panel BACnet Required Points Software Network OPC Client DI AO DO Thermostat Integration
1 1 1 1 1 1

Remarks
From Pump Control Panel Flow switch From Pump Control Panel From Pump Control Panel Relay Output From BMS Liquid pressure switch Liquid pressure sensor From Pump Control Panel

1 1 1 1 9 9 12 0 0 1 1

From Pump Control Panel From Pump Control Panel From Pump Control Panel From Pump Control Panel

2 of 2

Project : ITCC- Building RD-04(Main Building) Subject : BMS Input / Output List - Plumbing & Fire Protection Item Qty. Point Description
Plumbing and Fire Protection Equipments In-line Electric Driven Fire Pumps (1-Duty) in 4th basement 1 2 3 4 5 6 7 1 Pump On/Off Status Water flow status Pump Trip Alarm Pump Auto / Manual Status Pump Start/stop command Discharge header pressure Pump motor temperature high TOTAL Total Electric Driven Fire Pump Points Total Electric Driven Fire Pump Points 1 1 2 2

AI

Note: Fire Protection Control with Fire Alarm Panel BACnet Required Points Software Network OPC Client DI AO DO Thermostat Integration

Remarks

1 1 1 1 1

From Pump Control Panel Flow switch From Pump Control Panel From Pump Control Panel Relay Output From BMS Liquid pressure sensor From Pump Control Panel

4 4 7

0 0

1 1

Sump Pumps (1-Duty & 1-Lag each) [Ref.: SP-1,2,3,4,5] - 5 nos. Lift Sta. in basement 1 2 3 4 5 6 10 Pump on/off Status Pump Trip Status Pressure in the Common Discharge Header Pump Auto / Manual Status Run time meter reading (no input) Sump High & Low Level Total per Unit Total for all Units Total Sump Pumps Points Non-Potable Water Pumps (1-Duty&1-Standby) [Ref. No.: DP-1,2] 1 2 3 4 5 6 7 8 2 Pump On/Off Status Water flow status Pump Trip Alarm Pump Auto / Manual Status Pump Start/stop command Discharge header pressure Run time meter reading (no input) Pump motor temperature high TOTAL Total Potable Water Pumps Points Total Potable Water Pumps Points 1 2 3 4 8 19 0 0 1 3 4 8 1 1 1 1 1 VFC From Pump Control Panel Flow switch VFC From Pump Control Panel VFC From Pump Control Panel Relay Output From BMS Liquid pressure sensor Vertual sensor with BMS From Pump Control Panel 1 3 2 6 60 83 0 0 1 1 2 2 20 2 1 From Pump Control Panel From Pump Control Panel Liquid Pressure Sensor From Pump Control Panel Vertual sensor with BMS From Tank Float Switch

1 of 2

Project : ITCC- Building RD-04(Main Building) Subject : BMS Input / Output List - Plumbing & Fire Protection Item Qty.
1 2 3 4 5 6 7 8 9 10 11 12 1 Pump On/Off Status Fuel flow status Pump Trip Alarm Pump Auto / Manual Status Pump Start/stop command Discharge header pressure switch Discharge header pressure Pump motor temperature high Bulk Storage Tank Fuel Level Bulk Storage Tank Low Level Alarm Day Tank Low Level Alarm Day Tank Fuel Level Total per Unit Total for all Units 2 2 1 1

Point Description
Diesel Fuel Transfer Pumps + Bulk Storage Tank [1-Duty ] -1 set

AI

Note: Fire Protection Control with Fire Alarm Panel BACnet Required Points Software Network OPC Client DI AO DO Thermostat Integration
1 1 1 1 1 1

Remarks
From Pump Control Panel Flow switch From Pump Control Panel From Pump Control Panel Relay Output From BMS Liquid pressure switch Liquid pressure sensor From Pump Control Panel

1 1 1 1 9 9 12 0 0 1 1

From Pump Control Panel From Pump Control Panel From Pump Control Panel From Pump Control Panel

2 of 2

Project : ITCC- Building IT01.IT02,IT03 Subject : BMS Input / Output List - Plumbing & Fire Protection Item Qty. Point Description
Plumbing and Fire Protection Equipments In-line Electric Driven Fire Pumps (1-Duty) in basement each building 1 2 3 4 5 6 7 1 Pump On/Off Status Water flow status Pump Trip Alarm Pump Auto / Manual Status Pump Start/stop command Discharge header pressure Pump motor temperature high TOTAL Total Electric Driven Fire Pump Points Total Electric Driven Fire Pump Points 1 1 2 2

AI

Note: Fire Protection Control with Fire Alarm Panel BACnet Required Points Software Network OPC Client DI AO DO Thermostat Integration

Remarks

1 1 1 1 1

From Pump Control Panel Flow switch From Pump Control Panel From Pump Control Panel Relay Output From BMS Liquid pressure sensor From Pump Control Panel

4 4 7

0 0

1 1

Sump Pumps (1-Duty & 1-Standby each) [Ref.: SP-1,2,3,4,] - 4 nos. Lift Sta. @ 3rd. Basement each building 1 2 3 4 5 6 8 Pump on/off Status Pump Trip Status Pressure in the Common Discharge Header Pump Auto / Manual Status Run time meter reading (no input) Sump High & Low Level Total per Unit Total for all Units Total Sump Pumps Points Non-Potable Water Pumps (2-Duty&1-Standby) each building 1 2 3 4 5 6 7 8 3 Pump On/Off Status Water flow status Pump Trip Alarm Pump Auto / Manual Status Pump Start/stop command Discharge header pressure Run time meter reading (no input) Pump motor temperature high TOTAL Total Potable Water Pumps Points Total Potable Water Pumps Points 1 2 4 5 15 31 0 0 1 3 4 12 2 1 1 1 1 VFC From Pump Control Panel Flow switch VFC From Pump Control Panel VFC From Pump Control Panel Relay Output From BMS Liquid pressure sensor Vertual sensor with BMS From Pump Control Panel 1 3 2 6 48 67 0 0 1 1 2 2 16 2 1 From Pump Control Panel From Pump Control Panel Liquid Pressure Sensor From Pump Control Panel Vertual sensor with BMS From Tank Float Switch

1 of 2

Project : ITCC- Building IT01.IT02,IT03 Subject : BMS Input / Output List - Plumbing & Fire Protection Item Qty.
1 2 3 4 5 6 7 8 9 10 11 12 2 Pump On/Off Status Fuel flow status Pump Trip Alarm Pump Auto / Manual Status Pump Start/stop command Discharge header pressure switch Discharge header pressure Pump motor temperature high Bulk Storage Tank Fuel Level Bulk Storage Tank Low Level Alarm Day Tank Low Level Alarm Day Tank Fuel Level Total per Unit Total for all Units 2 4 1 1

Point Description

AI

Note: Fire Protection Control with Fire Alarm Panel BACnet Required Points Software Network OPC Client DI AO DO Thermostat Integration
2 1 1 1 1 1

Remarks
From Pump Control Panel Flow switch From Pump Control Panel From Pump Control Panel Relay Output From BMS Liquid pressure switch Liquid pressure sensor From Pump Control Panel

Diesel Fuel Transfer Pumps + Bulk Storage Tank [1-Duty/1-Standby ] -1 set each building

1 1 1 1 10 20 26 0 0 1 2

From Pump Control Panel From Pump Control Panel From Pump Control Panel From Pump Control Panel

Fountain Pumps (1-Duty ) - Locations : Fountain-1 near IT-02 & Fountain-2 front of IT-1 & IT-2 1 2 3 4 5 6 7 8 2 Pump On/Off Status Water flow status Pump Trip Alarm Pump Auto / Manual Status Pump Start/stop command Discharge header pressure switch Discharge header pressure Pump motor temperature high TOTAL Total Fountain Pumps Points Total Fountain Pumps Points 1 1 2 1 1 6 12 16 0 0 1 2 1 1 1 1 1 From Pump Control Panel Flow switch From Pump Control Panel From Pump Control Panel Relay Output From BMS Liquid pressure switch Liquid pressure sensor From Pump Control Panel

2 of 2

APPENDIX B: BUILDING MANAGEMENT SYSTEM (HVAC INPUT/OUTPUT LISTS)

ITCC in Riyadh Bldg KB04-KB06, IT01-IT03 & RD03-RD04 J09-07800

Divider

Project : ITTC 18 PARCELS (KB-04) Subject : BMS Input / Output List Item Qty.
1 2 3 4 5 6 1 Chilled Water Meters Differential Pressure Transmitter Motorized Valve (HX) By-Pass Motorized Valve Pressure Indicator Temperature Indicator Total per Unit Total for all Units Total ETS Points Tertiary Chilled Water System 1 2 3 5 1 Tertiary Common Chilled Water Supply Temperature Tertiary commom Chilled Water Return Temperature Tertiary Chilled Water Flow Tertiary Loop Chilled Water Differential Pressure in Loop Total per Unit Tertiary Chilled Water Pump VFD Feedback 6 7 8 9 10 3 Tertiary Chilled Water Pump Run Status Tertiary Chilled Water Pump VFD Trip Tertiary Chilled Water Pump VFD Auto / Manual Tertiary Chilled Water Pump VFD Control Tertiary Chilled Water Pump Enable / Disable Total per Unit Total for all Units Total Tertiary Chilled Water System points 1 6 2 6 18 1 1 0 1 3 1 0 1 1 1 1 1 3 1 3 0-10V From Pump VFD Control Panel VFC From Pump Control Panel VFC From Pump Control Panel VFC From Pump Control Panel 0-10V DC Signal From BMS Relay Output From BMS Immersion Temperature Sensor Immersion Temperature Sensor Flow Meter(By Others) Liquid Differential Pressure Sensor 1 1 3 3 1 1 7 3 3 0 0

Point Description
Energy transfer Station (ETS)

AI
1

Required Points DI AO
1 1 1 1

DO

BACnet Network Thermostat

Software OPC Client Integration Water Flow Meter

Remarks

Liquid Differential Pressure Sensor VFC from Valve Limit Switch (valve by others) VFC from Valve Limit Switch (valve by others) Liquid Pressure Sensor Immersion Temperature Sensor

1 of 49

Project : ITTC 18 PARCELS (KB-04) Subject : BMS Input / Output List Item Qty.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 3

Point Description
Point List - Through OSP/BACnet connection (cont.) Frequency Output (in Hz) Percent Output Speed (in RPM) Current (in Amps) Torque (in %) Power(in %) Run Time hours Run/Stop Status VSD Fault Alarm Current Limit(in %) Accel Time (in sec) Decel Time(in sec) VSD speed modulate start/stop command Total per Unit Total for all Units Total Point List-Through OSP/BACnet connection (cont.)

AI
-

Required Points DI AO

DO

BACnet Network Thermostat

Software OPC Client Integration

Remarks

0 0 0 0 0 0 0 0 0

Through OSP/BACnet Connection

1 3 3

2 of 49

Project : ITTC 18 PARCELS (KB-04) Subject : BMS Input / Output List Item Qty.
AHU( VAV ) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 2 Return Air Temperature Return Air Humidity Return Air Carbon Dioxide Mixed Air Temperature Supply Air Temperature Supply Duct static pressure Outside Air Temperature 2-Way Cooling Valve Position feedback Chilled water supply temperature Chilled water return temperature Supply Fan VFD Feedback Supply Fan status Supply fan air flow status Supply Fan Auto / Manual Supply Fan General Alarm Fresh air Damper Open / Close Feedback Return air Damper Open / Close Feedback Smoke Detector Supply fan VFD control 2-Way Cooling Valve Control Supply Fan Start/Stop Final Filter Status Pre Filter Status Fresh air Damper open/close Command Return air Damper Open / Close Command Electric Heater Status Electric Heater Current Switch Electric Heater Auto / Manual Electric Heater Start / Stop Total per Unit Total for all Units TOTAL AHU (VAV) Points 11 22 10 20 52 2 4 0 0 0 0 3 6 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 1 1 1

Point Description

AI

Required Points DI AO

DO

BACnet Network Thermostat

Software OPC Client Integration

Remarks

3 of 49

Project : ITTC 18 PARCELS (KB-04) Subject : BMS Input / Output List Item Qty.
FAHU( CAV ) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 2 Supply Air Temperature Outside Air Temperature Chilled water supply temperature Chilled water return temperature 2-Way Cooling Valve Position feedback Final Filter Status Pre Filter Status Supply Fan Status Supply fan air flow status Supply Fan Trip Supply Fan Auto / Manual Fresh air Damper Open / Close Feedback Exhaust air Damper Open / Close Feedback Smoke Detector 2-Way Cooling Valve Control Supply Fan Start/Stop Fresh air Damper open / close Command Exhaust air Damper open / close Command Total per Unit Total for all Units TOTAL FAHU (CAV) Points 5 10 8 16 32 1 2 1 1 1 1 1 1 1 1 1 1 1 1 0 1 1 1 1 0 2 4

Point Description

AI

Required Points DI AO

DO

BACnet Network Thermostat

Software OPC Client Integration

Remarks

4 of 49

Project : ITTC 18 PARCELS (KB-04) Subject : BMS Input / Output List Item Qty.
Fan Coil Units (FCU) 1 2 3 4 5 6 7 Return Air Temperature Air Flow Filter Status Supply Fan Status 29 Supply Fan Auto / Manual Supply Fan Air Flow Switch Supply Fan Start / Stop 2- Way Control Valve Open / Close Command Total per Unit Total for all Units Total Fan Coil Units (FCU) Points Fan Coil Units (FCU) with Electric Heater 1 2 3 4 5 6 7 8 9 10 11 2 Return Air Temperature Air Flow Filter Status Supply Fan Status Supply Fan Auto / Manual Supply Fan Air Flow Switch Supply Fan Start / Stop 2- Way Control Valve Open / Close Command Electric Heater Status Electric Heater Current Switch Electric Heater Auto / Manual Electric Heater Start / Stop Total per Unit Total for all Units Total Fan Coil Units (FCU) with Electric Heater Points 1 2 7 14 22 0 0 1 1 1 1 3 6 1 1 1 1 1 1 1 1 29 4 116 203 0 0 1 1 1 1 1 1 1 2 58

Point Description

AI

Required Points DI AO

DO

BACnet Network Thermostat

Software OPC Client Integration

Remarks

5 of 49

Project : ITTC 18 PARCELS (KB-04) Subject : BMS Input / Output List Item Qty. Point Description
VAV Box with Electric Heater 1 2 3 7 Space Temperature sensor with set point Damper Actuator modulate Enable/Disable Stages of Electric Heater Total per Unit Total for all Units Total VAV Box with Electric Heater points VAV Box without Electric Heater 1 2 3 3 Space Temperature sensor with set point Damper Actuator modulate Enable/Disable Stages of Electric Heater Total per Unit Total for all Units Total VAV Box with Electric Heater points Exhaust Fans 1 2 3 4 5 19 Fan Status Fan Trip Fan Auto/Manual Fan Start/Stop Fan Air Flow Status Total per Unit Total for all Units Total Exhaust Fans Points Smoke Exhaust 1 2 3 4 2 Fan Status Fan Trip Fan Auto/Manual Fan Air Flow Status Total per Unit Total for all Units TOTAL Smoke Exhaust Fans Points 0 0 1 1 1 1 4 8 8 0 0 0 0 0 0 1 4 76 95 0 0 1 1 1 1 1 19 1 3 0 0 6 1 1 0 1 3 0 0 Space Temperature Sensor with set point 0-10v Signal to Damper Actuator Relay Output From BMS 1 7 0 0 28 1 1 2 1 7 2 14 Space Temperature Sensor with set point 0-10v Signal to Damper Actuator Relay Output From BMS

AI

Required Points DI AO

DO

BACnet Network Thermostat

Software OPC Client Integration

Remarks

6 of 49

Project : ITTC 18 PARCELS (KB-04) Subject : BMS Input / Output List Item Qty.
Pressurization Fans 1 2 3 4 5 6 0 Fan Status Fan Trip Fan Auto/Manual Fan Air Flow Status Air Damper Open / Close Feedback Air Damper Open / Close Command Total per Unit Total for all Units Total Pressurization Fans Points Impulse Fans 1 2 3 4 Start/Stop Control 15 Contactor Status Air Flow Monitoring Motor Fail/Trip Total per Unit Total for all Units Total Impulse Fans Points Energy Recovery Unit 1 2 3 4 5 2 Fan Status Fan Trip Fan Auto/Manual Fan Start/Stop Fan Air Flow Status Total per Unit Total for all Units Total Energy Recovery Units Points 0 0 1 4 8 10 0 0 1 1 1 1 1 2 0 0 3 45 60 0 0 0 1 1 1 1 1 15 0 0 0 0 1 1 1 1 1 5 0 0 0 0 1 1 0

Point Description

AI

Required Points DI AO

DO

BACnet Network Thermostat

Software OPC Client Integration

Remarks

7 of 49

Project : ITTC 18 PARCELS (KB-05) Subject : BMS Input / Output List Item Qty.
1 2 3 4 5 6 1 Chilled Water Meters Differential Pressure Transmitter Motorized Valve (HX) By-Pass Motorized Valve Pressure Indicator Temperature Indicator Total per Unit Total for all Units Total ETS Points Tertiary Chilled Water System 1 2 3 5 1 Tertiary Common Chilled Water Supply Temperature Tertiary commom Chilled Water Return Temperature Tertiary Chilled Water Flow Tertiary Loop Chilled Water Differential Pressure in Loop Total per Unit Tertiary Chilled Water Pump VFD Feedback 6 7 8 9 10 3 Tertiary Chilled Water Pump Run Status Tertiary Chilled Water Pump VFD Trip Tertiary Chilled Water Pump VFD Auto / Manual Tertiary Chilled Water Pump VFD Control Tertiary Chilled Water Pump Enable / Disable Total per Unit Total for all Units Total Tertiary Chilled Water System points 1 6 2 6 18 1 1 0 1 3 1 0 1 1 1 1 1 3 1 3 0-10V From Pump VFD Control Panel VFC From Pump Control Panel VFC From Pump Control Panel VFC From Pump Control Panel 0-10V DC Signal From BMS Relay Output From BMS Immersion Temperature Sensor Immersion Temperature Sensor Flow Meter(By Others) Liquid Differential Pressure Sensor 1 1 3 3 1 1 7 3 3 0 0

Point Description
Energy transfer Station (ETS)

AI
1

Required Points DI AO
1 1 1 1

DO

BACnet Network Thermostat

Software OPC Client Integration Water Flow Meter

Remarks

Liquid Differential Pressure Sensor VFC from Valve Limit Switch (valve by others) VFC from Valve Limit Switch (valve by others) Liquid Pressure Sensor Immersion Temperature Sensor

8 of 49

Project : ITTC 18 PARCELS (KB-05) Subject : BMS Input / Output List Item Qty.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 3

Point Description
Point List - Through OSP/BACnet connection (cont.) Frequency Output (in Hz) Percent Output Speed (in RPM) Current (in Amps) Torque (in %) Power(in %) Run Time hours Run/Stop Status VSD Fault Alarm Current Limit(in %) Accel Time (in sec) Decel Time(in sec) VSD speed modulate start/stop command Total per Unit Total for all Units Total Point List-Through OSP/BACnet connection (cont.)

AI
-

Required Points DI AO

DO

BACnet Network Thermostat

Software OPC Client Integration

Remarks

0 0 0 0 0 0 0 0 0

Through OSP/BACnet Connection

1 3 3

9 of 49

Project : ITTC 18 PARCELS (KB-05) Subject : BMS Input / Output List Item Qty.
FAHU( CAV ) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 2 Supply Air Temperature Outside Air Temperature Chilled water supply temperature Chilled water return temperature 2-Way Cooling Valve Position feedback Final Filter Status Pre Filter Status Supply Fan Status Supply fan air flow status Supply Fan Trip Supply Fan Auto / Manual Fresh air Damper Open / Close Feedback Exhaust air Damper Open / Close Feedback Smoke Detector 2-Way Cooling Valve Control Supply Fan Start/Stop Fresh air Damper open / close Command Exhaust air Damper open / close Command Total per Unit Total for all Units TOTAL FAHU (CAV) Points 5 10 8 16 32 1 2 1 1 1 1 1 1 1 1 1 1 1 1 0 1 1 1 1 0 2 4

Point Description

AI

Required Points DI AO

DO

BACnet Network Thermostat

Software OPC Client Integration

Remarks

10 of 49

Project : ITTC 18 PARCELS (KB-05) Subject : BMS Input / Output List Item Qty.
Fan Coil Units (FCU) 1 2 3 4 5 6 7 Return Air Temperature Air Flow Filter Status Supply Fan Status 32 Supply Fan Auto / Manual Supply Fan Air Flow Switch Supply Fan Start / Stop 2- Way Control Valve Open / Close Command Total per Unit Total for all Units Total Fan Coil Units (FCU) Points Fan Coil Units (FCU) with Electric Heater 1 2 3 4 5 6 7 8 9 10 11 4 Return Air Temperature Air Flow Filter Status Supply Fan Status Supply Fan Auto / Manual Supply Fan Air Flow Switch Supply Fan Start / Stop 2- Way Control Valve Open / Close Command Electric Heater Status Electric Heater Current Switch Electric Heater Auto / Manual Electric Heater Start / Stop Total per Unit Total for all Units Total Fan Coil Units (FCU) with Electric Heater Points Exhaust Fans 1 2 3 4 5 10 Fan Status Fan Trip Fan Auto/Manual Fan Start/Stop Fan Air Flow Status Total per Unit Total for all Units Total Exhaust Fans Points 0 0 1 4 40 0 0 50 11 of 49 1 1 1 1 1 10 1 4 7 28 44 0 0 1 1 1 1 3 12 1 1 1 1 1 1 1 1 32 4 128 224 0 0 1 1 1 1 1 1 1 2 64

Point Description

AI

Required Points DI AO

DO

BACnet Network Thermostat

Software OPC Client Integration

Remarks

Project : ITTC 18 PARCELS (KB-05) Subject : BMS Input / Output List Item Qty.
Smoke Exhaust 1 2 3 4 0 Fan Status Fan Trip Fan Auto/Manual Fan Air Flow Status Total per Unit Total for all Units TOTAL Smoke Exhaust Fans Points Pressurization Fans 1 2 3 4 5 6 0 Fan Status Fan Trip Fan Auto/Manual Fan Air Flow Status Air Damper Open / Close Feedback Air Damper Open / Close Command Total per Unit Total for all Units Total Pressurization Fans Points 0 0 1 1 1 1 1 5 0 0 0 0 1 1 0 0 0 1 1 1 1 4 0 0 0 0 0 0

Point Description

AI

Required Points DI AO

DO

BACnet Network Thermostat

Software OPC Client Integration

Remarks

12 of 49

Project : ITTC 18 PARCELS (KB-05) Subject : BMS Input / Output List Item Qty.
Impulse Fans 1 2 3 4 Start/Stop Control 17 Contactor Status Air Flow Monitoring Motor Fail/Trip Total per Unit Total for all Units Total Impulse Fans Points Energy Recovery Unit 1 2 3 4 5 2 Fan Status Fan Trip Fan Auto/Manual Fan Start/Stop Fan Air Flow Status Total per Unit Total for all Units Total Energy Recovery Units Points 0 0 1 4 8 10 0 0 1 1 1 1 1 2 0 0 3 51 68 0 0 0 1 1 1 1 1 17 0 0

Point Description

AI

Required Points DI AO

DO

BACnet Network Thermostat

Software OPC Client Integration

Remarks

13 of 49

Project : ITTC 18 PARCELS (KB-06) Subject : BMS Input / Output List Item Qty.
1 2 3 4 5 6 1 Chilled Water Meters Differential Pressure Transmitter Motorized Valve (HX) By-Pass Motorized Valve Pressure Indicator Temperature Indicator Total per Unit Total for all Units Total ETS Points Tertiary Chilled Water System 1 2 3 5 1 Tertiary Common Chilled Water Supply Temperature Tertiary commom Chilled Water Return Temperature Tertiary Chilled Water Flow Tertiary Loop Chilled Water Differential Pressure in Loop Total per Unit Tertiary Chilled Water Pump VFD Feedback 6 7 8 9 10 3 Tertiary Chilled Water Pump Run Status Tertiary Chilled Water Pump VFD Trip Tertiary Chilled Water Pump VFD Auto / Manual Tertiary Chilled Water Pump VFD Control Tertiary Chilled Water Pump Enable / Disable Total per Unit Total for all Units Total Tertiary Chilled Water System points 1 6 2 6 18 1 1 0 1 3 1 0 1 1 1 1 1 3 1 3 0-10V From Pump VFD Control Panel VFC From Pump Control Panel VFC From Pump Control Panel VFC From Pump Control Panel 0-10V DC Signal From BMS Relay Output From BMS Immersion Temperature Sensor Immersion Temperature Sensor Flow Meter(By Others) Liquid Differential Pressure Sensor 1 1 3 3 1 1 7 3 3 0 0

Point Description
Energy transfer Station (ETS)

AI
1

Required Points DI AO
1 1 1 1

DO

BACnet Network Thermostat

Software OPC Client Integration Water Flow Meter

Remarks

Liquid Differential Pressure Sensor VFC from Valve Limit Switch (valve by others) VFC from Valve Limit Switch (valve by others) Liquid Pressure Sensor Immersion Temperature Sensor

14 of 49

Project : ITTC 18 PARCELS (KB-06) Subject : BMS Input / Output List Item Qty.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 3

Point Description
Point List - Through OSP/BACnet connection (cont.) Frequency Output (in Hz) Percent Output Speed (in RPM) Current (in Amps) Torque (in %) Power(in %) Run Time hours Run/Stop Status VSD Fault Alarm Current Limit(in %) Accel Time (in sec) Decel Time(in sec) VSD speed modulate start/stop command Total per Unit Total for all Units Total Point List-Through OSP/BACnet connection (cont.)

AI
-

Required Points DI AO

DO

BACnet Network Thermostat

Software OPC Client Integration

Remarks

0 0 0 0 0 0 0 0 0

Through OSP/BACnet Connection

1 3 3

15 of 49

Project : ITTC 18 PARCELS (KB-06) Subject : BMS Input / Output List Item Qty.
FAHU( CAV ) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 2 Supply Air Temperature Outside Air Temperature Chilled water supply temperature Chilled water return temperature 2-Way Cooling Valve Position feedback Final Filter Status Pre Filter Status Supply Fan Status Supply fan air flow status Supply Fan Trip Supply Fan Auto / Manual Fresh air Damper Open / Close Feedback Exhaust air Damper Open / Close Feedback Smoke Detector 2-Way Cooling Valve Control Supply Fan Start/Stop Fresh air Damper open / close Command Exhaust air Damper open / close Command Total per Unit Total for all Units TOTAL FAHU (CAV) Points 5 10 8 16 32 1 2 1 1 1 1 1 1 1 1 1 1 1 1 0 1 1 1 1 0 2 4

Point Description

AI

Required Points DI AO

DO

BACnet Network Thermostat

Software OPC Client Integration

Remarks

16 of 49

Project : ITTC 18 PARCELS (KB-06) Subject : BMS Input / Output List Item Qty.
Fan Coil Units (FCU) 1 2 3 4 5 6 7 Return Air Temperature Air Flow Filter Status Supply Fan Status 51 Supply Fan Auto / Manual Supply Fan Air Flow Switch Supply Fan Start / Stop 2- Way Control Valve Open / Close Command Total per Unit Total for all Units Total Fan Coil Units (FCU) Points Fan Coil Units (FCU) with Electric Heater 1 2 3 4 5 6 7 8 9 10 11 1 Return Air Temperature Air Flow Filter Status Supply Fan Status Supply Fan Auto / Manual Supply Fan Air Flow Switch Supply Fan Start / Stop 2- Way Control Valve Open / Close Command Electric Heater Status Electric Heater Current Switch Electric Heater Auto / Manual Electric Heater Start / Stop Total per Unit Total for all Units Total Fan Coil Units (FCU) with Electric Heater Points Exhaust Fans 1 2 3 4 5 18 Fan Status Fan Trip Fan Auto/Manual Fan Start/Stop Fan Air Flow Status Total per Unit Total for all Units Total Exhaust Fans Points 0 0 1 4 72 0 0 90 17 of 49 1 1 1 1 1 18 1 1 7 7 11 0 0 1 1 1 1 3 3 1 1 1 1 1 1 1 1 51 4 204 357 0 0 1 1 1 1 1 1 1 2 102

Point Description

AI

Required Points DI AO

DO

BACnet Network Thermostat

Software OPC Client Integration

Remarks

Project : ITTC 18 PARCELS (KB-06) Subject : BMS Input / Output List Item Qty.
Smoke Exhaust 1 2 3 4 0 Fan Status Fan Trip Fan Auto/Manual Fan Air Flow Status Total per Unit Total for all Units TOTAL Smoke Exhaust Fans Points Pressurization Fans 1 2 3 4 5 6 3 Fan Status Fan Trip Fan Auto/Manual Fan Air Flow Status Air Damper Open / Close Feedback Air Damper Open / Close Command Total per Unit Total for all Units Total Pressurization Fans Points 0 0 1 1 1 1 1 5 15 18 0 0 1 1 3 0 0 1 1 1 1 4 0 0 0 0 0 0

Point Description

AI

Required Points DI AO

DO

BACnet Network Thermostat

Software OPC Client Integration

Remarks

18 of 49

Project : ITTC 18 PARCELS (KB-06) Subject : BMS Input / Output List Item Qty.
Impulse Fans 1 2 3 4 Start/Stop Control 34 Contactor Status Air Flow Monitoring Motor Fail/Trip Total per Unit Total for all Units Total Impulse Fans Points Energy Recovery Unit 1 2 3 4 5 2 Fan Status Fan Trip Fan Auto/Manual Fan Start/Stop Fan Air Flow Status Total per Unit Total for all Units Total Energy Recovery Units Points 0 0 1 4 8 10 0 0 1 1 1 1 1 2 0 0 3 102 136 0 0 0 1 1 1 1 1 34 0 0

Point Description

AI

Required Points DI AO

DO

BACnet Network Thermostat

Software OPC Client Integration

Remarks

19 of 49

Project : ITTC 18 PARCELS (RD-03) Subject : BMS Input / Output List Item Qty.
1 2 3 4 5 6 1 Chilled Water Meters Differential Pressure Transmitter Motorized Valve (HX) By-Pass Motorized Valve Pressure Indicator Temperature Indicator Total per Unit Total for all Units Total ETS Points Tertiary Chilled Water System 1 2 3 5 1 Tertiary Common Chilled Water Supply Temperature Tertiary commom Chilled Water Return Temperature Tertiary Chilled Water Flow Tertiary Loop Chilled Water Differential Pressure in Loop Total per Unit Tertiary Chilled Water Pump VFD Feedback 6 7 8 9 10 3 Tertiary Chilled Water Pump Run Status Tertiary Chilled Water Pump VFD Trip Tertiary Chilled Water Pump VFD Auto / Manual Tertiary Chilled Water Pump VFD Control Tertiary Chilled Water Pump Enable / Disable Total per Unit Total for all Units Total Tertiary Chilled Water System points 1 6 2 6 18 1 1 0 1 3 1 0 1 1 1 1 1 3 1 3 0-10V From Pump VFD Control Panel VFC From Pump Control Panel VFC From Pump Control Panel VFC From Pump Control Panel 0-10V DC Signal From BMS Relay Output From BMS Immersion Temperature Sensor Immersion Temperature Sensor Flow Meter(By Others) Liquid Differential Pressure Sensor 1 1 3 3 1 1 7 3 3 0 0

Point Description
Energy transfer Station (ETS)

AI
1

Required Points DI AO
1 1 1 1

DO

BACnet Network Thermostat

Software OPC Client Integration Water Flow Meter

Remarks

Liquid Differential Pressure Sensor VFC from Valve Limit Switch (valve by others) VFC from Valve Limit Switch (valve by others) Liquid Pressure Sensor Immersion Temperature Sensor

20 of 49

Project : ITTC 18 PARCELS (RD-03) Subject : BMS Input / Output List Item Qty.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 3

Point Description
Point List - Through OSP/BACnet connection (cont.) Frequency Output (in Hz) Percent Output Speed (in RPM) Current (in Amps) Torque (in %) Power(in %) Run Time hours Run/Stop Status VSD Fault Alarm Current Limit(in %) Accel Time (in sec) Decel Time(in sec) VSD speed modulate start/stop command Total per Unit Total for all Units Total Point List-Through OSP/BACnet connection (cont.)

AI
-

Required Points DI AO

DO

BACnet Network Thermostat

Software OPC Client Integration

Remarks

0 0 0 0 0 0 0 0 0

Through OSP/BACnet Connection

1 3 3

21 of 49

Project : ITTC 18 PARCELS (RD-03) Subject : BMS Input / Output List Item Qty.
FAHU( CAV ) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 1 Supply Air Temperature Outside Air Temperature Chilled water supply temperature Chilled water return temperature 2-Way Cooling Valve Position feedback Final Filter Status Pre Filter Status Supply Fan Status Supply fan air flow status Supply Fan Trip Supply Fan Auto / Manual Fresh air Damper Open / Close Feedback Exhaust air Damper Open / Close Feedback Smoke Detector 2-Way Cooling Valve Control Supply Fan Start/Stop Fresh air Damper open / close Command Exhaust air Damper open / close Command Total per Unit Total for all Units TOTAL FAHU (CAV) Points 5 5 8 8 16 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 1 1 1 1 0 2 2

Point Description

AI

Required Points DI AO

DO

BACnet Network Thermostat

Software OPC Client Integration

Remarks

22 of 49

Project : ITTC 18 PARCELS (RD-03) Subject : BMS Input / Output List Item Qty.
Fan Coil Units (FCU) 1 2 3 4 5 6 7 Return Air Temperature Air Flow Filter Status Supply Fan Status 55 Supply Fan Auto / Manual Supply Fan Air Flow Switch Supply Fan Start / Stop 2- Way Control Valve Open / Close Command Total per Unit Total for all Units Total Fan Coil Units (FCU) Points Fan Coil Units (FCU) with Electric Heater 1 2 3 4 5 6 7 8 9 10 11 6 Return Air Temperature Air Flow Filter Status Supply Fan Status Supply Fan Auto / Manual Supply Fan Air Flow Switch Supply Fan Start / Stop 2- Way Control Valve Open / Close Command Electric Heater Status Electric Heater Current Switch Electric Heater Auto / Manual Electric Heater Start / Stop Total per Unit Total for all Units Total Fan Coil Units (FCU) with Electric Heater Points Exhaust Fans 1 2 3 4 5 29 Fan Status Fan Trip Fan Auto/Manual Fan Start/Stop Fan Air Flow Status Total per Unit Total for all Units Total Exhaust Fans Points 0 0 1 4 116 0 0 145 23 of 49 1 1 1 1 1 29 1 6 7 42 66 0 0 1 1 1 1 3 18 1 1 1 1 1 1 1 1 55 4 220 385 0 0 1 1 1 1 1 1 1 2 110

Point Description

AI

Required Points DI AO

DO

BACnet Network Thermostat

Software OPC Client Integration

Remarks

Project : ITTC 18 PARCELS (RD-03) Subject : BMS Input / Output List Item Qty.
Smoke Exhaust 1 2 3 4 1 Fan Status Fan Trip Fan Auto/Manual Fan Air Flow Status Total per Unit Total for all Units TOTAL Smoke Exhaust Fans Points Pressurization Fans 1 2 3 4 5 6 3 Fan Status Fan Trip Fan Auto/Manual Fan Air Flow Status Air Damper Open / Close Feedback Air Damper Open / Close Command Total per Unit Total for all Units Total Pressurization Fans Points 0 0 1 1 1 1 1 5 15 18 0 0 1 1 3 0 0 1 1 1 1 4 4 4 0 0 0 0

Point Description

AI

Required Points DI AO

DO

BACnet Network Thermostat

Software OPC Client Integration

Remarks

24 of 49

Project : ITTC 18 PARCELS (RD-03) Subject : BMS Input / Output List Item Qty.
Impulse Fans 1 2 3 4 4 Start/Stop Control Contactor Status Air Flow Monitoring Motor Fail/Trip Total per Unit Total for all Units Total Impulse Fans Points Energy Recovery Unit 1 2 3 4 5 1 Fan Status Fan Trip Fan Auto/Manual Fan Start/Stop Fan Air Flow Status Total per Unit Total for all Units Total Energy Recovery Units Points 0 0 1 4 4 5 0 0 1 1 1 1 1 1 0 0 3 12 16 0 0 0 1 1 1 1 1 4 0 0

Point Description

AI

Required Points DI AO

DO

BACnet Network Thermostat

Software OPC Client Integration

Remarks

25 of 49

Project : ITTC 18 PARCELS (RD-04) Subject : BMS Input / Output List Item Qty.
1 2 3 4 5 6 1 Chilled Water Meters Differential Pressure Transmitter Motorized Valve (HX) By-Pass Motorized Valve Pressure Indicator Temperature Indicator Total per Unit Total for all Units Total ETS Points Tertiary Chilled Water System 1 2 3 5 1 Tertiary Common Chilled Water Supply Temperature Tertiary commom Chilled Water Return Temperature Tertiary Chilled Water Flow Tertiary Loop Chilled Water Differential Pressure in Loop Total per Unit Tertiary Chilled Water Pump VFD Feedback 6 7 8 9 10 3 Tertiary Chilled Water Pump Run Status Tertiary Chilled Water Pump VFD Trip Tertiary Chilled Water Pump VFD Auto / Manual Tertiary Chilled Water Pump VFD Control Tertiary Chilled Water Pump Enable / Disable Total per Unit Total for all Units Total Tertiary Chilled Water System points 1 6 2 6 18 1 1 0 1 3 1 0 1 1 1 1 1 3 1 3 0-10V From Pump VFD Control Panel VFC From Pump Control Panel VFC From Pump Control Panel VFC From Pump Control Panel 0-10V DC Signal From BMS Relay Output From BMS Immersion Temperature Sensor Immersion Temperature Sensor Flow Meter(By Others) Liquid Differential Pressure Sensor 1 1 3 3 1 1 7 3 3 0 0

Point Description
Energy transfer Station (ETS)

AI
1

Required Points DI AO
1 1 1 1

DO

BACnet Network Thermostat

Software OPC Client Integration Water Flow Meter

Remarks

Liquid Differential Pressure Sensor VFC from Valve Limit Switch (valve by others) VFC from Valve Limit Switch (valve by others) Liquid Pressure Sensor Immersion Temperature Sensor

26 of 49

Project : ITTC 18 PARCELS (RD-04) Subject : BMS Input / Output List Item Qty.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 3

Point Description
Point List - Through OSP/BACnet connection (cont.) Frequency Output (in Hz) Percent Output Speed (in RPM) Current (in Amps) Torque (in %) Power(in %) Run Time hours Run/Stop Status VSD Fault Alarm Current Limit(in %) Accel Time (in sec) Decel Time(in sec) VSD speed modulate start/stop command Total per Unit Total for all Units Total Point List-Through OSP/BACnet connection (cont.)

AI
-

Required Points DI AO

DO

BACnet Network Thermostat

Software OPC Client Integration

Remarks

0 0 0 0 0 0 0 0 0

Through OSP/BACnet Connection

1 3 3

27 of 49

Project : ITTC 18 PARCELS (RD-04) Subject : BMS Input / Output List Item Qty.
FAHU( CAV ) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 2 Supply Air Temperature Outside Air Temperature Chilled water supply temperature Chilled water return temperature 2-Way Cooling Valve Position feedback Final Filter Status Pre Filter Status Supply Fan Status Supply fan air flow status Supply Fan Trip Supply Fan Auto / Manual Fresh air Damper Open / Close Feedback Exhaust air Damper Open / Close Feedback Smoke Detector 2-Way Cooling Valve Control Supply Fan Start/Stop Fresh air Damper open / close Command Exhaust air Damper open / close Command Total per Unit Total for all Units TOTAL FAHU (CAV) Points 5 10 8 16 32 1 2 1 1 1 1 1 1 1 1 1 1 1 1 0 1 1 1 1 0 2 4

Point Description

AI

Required Points DI AO

DO

BACnet Network Thermostat

Software OPC Client Integration

Remarks

28 of 49

Project : ITTC 18 PARCELS (RD-04) Subject : BMS Input / Output List Item Qty.
Fan Coil Units (FCU) 1 2 3 4 5 6 7 Return Air Temperature Air Flow Filter Status Supply Fan Status 84 Supply Fan Auto / Manual Supply Fan Air Flow Switch Supply Fan Start / Stop 2- Way Control Valve Open / Close Command Total per Unit Total for all Units Total Fan Coil Units (FCU) Points Fan Coil Units (FCU) with Electric Heater 1 2 3 4 5 6 7 8 9 10 11 Return Air Temperature Air Flow Filter Status Supply Fan Status Supply Fan Auto / Manual Supply Fan Air Flow Switch 13 Supply Fan Start / Stop 2- Way Control Valve Open / Close Command Electric Heater Status Electric Heater Current Switch Electric Heater Auto / Manual Electric Heater Start / Stop Total per Unit Total for all Units Total Fan Coil Units (FCU) with Electric Heater Points Exhaust Fans 1 2 3 4 5 12 Fan Status Fan Trip Fan Auto/Manual Fan Start/Stop Fan Air Flow Status Total per Unit Total for all Units Total Exhaust Fans Points 0 0 1 4 48 0 0 60 29 of 49 1 1 1 1 1 12 1 13 7 91 143 0 0 1 1 1 1 3 39 1 1 1 1 1 1 1 1 84 4 336 588 0 0 1 1 1 1 1 1 1 2 168

Point Description

AI

Required Points DI AO

DO

BACnet Network Thermostat

Software OPC Client Integration

Remarks

Project : ITTC 18 PARCELS (RD-04) Subject : BMS Input / Output List Item Qty.
Smoke Exhaust 1 2 3 4 3 Fan Status Fan Trip Fan Auto/Manual Fan Air Flow Status Total per Unit Total for all Units TOTAL Smoke Exhaust Fans Points Pressurization Fans 1 2 3 4 5 6 3 Fan Status Fan Trip Fan Auto/Manual Fan Air Flow Status Air Damper Open / Close Feedback Air Damper Open / Close Command Total per Unit Total for all Units Total Pressurization Fans Points 0 0 1 1 1 1 1 5 15 18 0 0 1 1 3 0 0 1 1 1 1 4 12 12 0 0 0 0

Point Description

AI

Required Points DI AO

DO

BACnet Network Thermostat

Software OPC Client Integration

Remarks

30 of 49

Project : ITTC 18 PARCELS (RD-04) Subject : BMS Input / Output List Item Qty.
Impulse Fans 1 2 3 4 Start/Stop Control 36 Contactor Status Air Flow Monitoring Motor Fail/Trip Total per Unit Total for all Units Total Impulse Fans Points Energy Recovery Unit 1 2 3 4 5 2 Fan Status Fan Trip Fan Auto/Manual Fan Start/Stop Fan Air Flow Status Total per Unit Total for all Units Total Energy Recovery Units Points 0 0 1 4 8 10 0 0 1 1 1 1 1 2 0 0 3 108 144 0 0 0 1 1 1 1 1 36 0 0

Point Description

AI

Required Points DI AO

DO

BACnet Network Thermostat

Software OPC Client Integration

Remarks

31 of 49

Project : ITTC 18 PARCELS (IT-01) Subject : BMS Input / Output List Item Qty.
1 2 3 4 5 6 1 Chilled Water Meters Differential Pressure Transmitter Motorized Valve (HX) By-Pass Motorized Valve Pressure Indicator Temperature Indicator Total per Unit Total for all Units Total ETS Points Tertiary Chilled Water System 1 2 3 5 1 Tertiary Common Chilled Water Supply Temperature Tertiary commom Chilled Water Return Temperature Tertiary Chilled Water Flow Tertiary Loop Chilled Water Differential Pressure in Loop Total per Unit Tertiary Chilled Water Pump VFD Feedback 6 7 8 9 10 3 Tertiary Chilled Water Pump Run Status Tertiary Chilled Water Pump VFD Trip Tertiary Chilled Water Pump VFD Auto / Manual Tertiary Chilled Water Pump VFD Control Tertiary Chilled Water Pump Enable / Disable Total per Unit Total for all Units Total Tertiary Chilled Water System points 1 6 2 6 18 1 1 0 1 3 1 0 1 1 1 1 1 3 1 3 0-10V From Pump VFD Control Panel VFC From Pump Control Panel VFC From Pump Control Panel VFC From Pump Control Panel 0-10V DC Signal From BMS Relay Output From BMS Immersion Temperature Sensor Immersion Temperature Sensor Flow Meter(By Others) Liquid Differential Pressure Sensor 1 1 3 3 1 1 7 3 3 0 0

Point Description
Energy transfer Station (ETS)

AI
1

Required Points DI AO
1 1 1 1

DO

BACnet Network Thermostat

Software OPC Client Integration Water Flow Meter

Remarks

Liquid Differential Pressure Sensor VFC from Valve Limit Switch (valve by others) VFC from Valve Limit Switch (valve by others) Liquid Pressure Sensor Immersion Temperature Sensor

32 of 49

Project : ITTC 18 PARCELS (IT-01) Subject : BMS Input / Output List Item Qty.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 3

Point Description
Point List - Through OSP/BACnet connection (cont.) Frequency Output (in Hz) Percent Output Speed (in RPM) Current (in Amps) Torque (in %) Power(in %) Run Time hours Run/Stop Status VSD Fault Alarm Current Limit(in %) Accel Time (in sec) Decel Time(in sec) VSD speed modulate start/stop command Total per Unit Total for all Units Total Point List-Through OSP/BACnet connection (cont.)

AI
-

Required Points DI AO

DO

BACnet Network Thermostat

Software OPC Client Integration

Remarks

0 0 0 0 0 0 0 0 0

Through OSP/BACnet Connection

1 3 3

33 of 49

Project : ITTC 18 PARCELS (IT-01) Subject : BMS Input / Output List Item Qty.
FAHU( CAV ) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 2 Supply Air Temperature Outside Air Temperature Chilled water supply temperature Chilled water return temperature 2-Way Cooling Valve Position feedback Final Filter Status Pre Filter Status Supply Fan Status Supply fan air flow status Supply Fan Trip Supply Fan Auto / Manual Fresh air Damper Open / Close Feedback Exhaust air Damper Open / Close Feedback Smoke Detector 2-Way Cooling Valve Control Supply Fan Start/Stop Fresh air Damper open / close Command Exhaust air Damper open / close Command Total per Unit Total for all Units TOTAL FAHU (CAV) Points 5 10 8 16 32 1 2 1 1 1 1 1 1 1 1 1 1 1 1 0 1 1 1 1 0 2 4

Point Description

AI

Required Points DI AO

DO

BACnet Network Thermostat

Software OPC Client Integration

Remarks

34 of 49

Project : ITTC 18 PARCELS (IT-01) Subject : BMS Input / Output List Item Qty.
Fan Coil Units (FCU) 1 2 3 4 5 6 7 Return Air Temperature Air Flow Filter Status Supply Fan Status 25 Supply Fan Auto / Manual Supply Fan Air Flow Switch Supply Fan Start / Stop 2- Way Control Valve Open / Close Command Total per Unit Total for all Units Total Fan Coil Units (FCU) Points Fan Coil Units (FCU) with Electric Heater 1 2 3 4 5 6 7 8 9 10 11 Return Air Temperature Air Flow Filter Status Supply Fan Status Supply Fan Auto / Manual Supply Fan Air Flow Switch 19 Supply Fan Start / Stop 2- Way Control Valve Open / Close Command Electric Heater Status Electric Heater Current Switch Electric Heater Auto / Manual Electric Heater Start / Stop Total per Unit Total for all Units Total Fan Coil Units (FCU) with Electric Heater Points Exhaust Fans 1 2 3 4 5 13 Fan Status Fan Trip Fan Auto/Manual Fan Start/Stop Fan Air Flow Status Total per Unit Total for all Units Total Exhaust Fans Points 0 0 1 4 52 0 0 65 35 of 49 1 1 1 1 1 13 1 19 7 133 209 0 0 1 1 1 1 3 57 1 1 1 1 1 1 1 1 25 4 100 175 0 0 1 1 1 1 1 1 1 2 50

Point Description

AI

Required Points DI AO

DO

BACnet Network Thermostat

Software OPC Client Integration

Remarks

Project : ITTC 18 PARCELS (IT-01) Subject : BMS Input / Output List Item Qty.
Smoke Exhaust 1 2 3 4 1 Fan Status Fan Trip Fan Auto/Manual Fan Air Flow Status Total per Unit Total for all Units TOTAL Smoke Exhaust Fans Points Pressurization Fans 1 2 3 4 5 6 2 Fan Status Fan Trip Fan Auto/Manual Fan Air Flow Status Air Damper Open / Close Feedback Air Damper Open / Close Command Total per Unit Total for all Units Total Pressurization Fans Points 0 0 1 1 1 1 1 5 10 12 0 0 1 1 2 0 0 1 1 1 1 4 4 4 0 0 0 0

Point Description

AI

Required Points DI AO

DO

BACnet Network Thermostat

Software OPC Client Integration

Remarks

36 of 49

Project : ITTC 18 PARCELS (IT-01) Subject : BMS Input / Output List Item Qty.
Impulse Fans 1 2 3 4 Start/Stop Control 30 Contactor Status Air Flow Monitoring Motor Fail/Trip Total per Unit Total for all Units Total Impulse Fans Points Energy Recovery Unit 1 2 3 4 5 2 Fan Status Fan Trip Fan Auto/Manual Fan Start/Stop Fan Air Flow Status Total per Unit Total for all Units Total Energy Recovery Units Points 0 0 1 4 8 10 0 0 1 1 1 1 1 2 0 0 3 90 120 0 0 0 1 1 1 1 1 30 0 0

Point Description

AI

Required Points DI AO

DO

BACnet Network Thermostat

Software OPC Client Integration

Remarks

37 of 49

Project : ITTC 18 PARCELS (IT-02) Subject : BMS Input / Output List Item Qty.
1 2 3 4 5 6 1 Chilled Water Meters Differential Pressure Transmitter Motorized Valve (HX) By-Pass Motorized Valve Pressure Indicator Temperature Indicator Total per Unit Total for all Units Total ETS Points Tertiary Chilled Water System 1 2 3 5 1 Tertiary Common Chilled Water Supply Temperature Tertiary commom Chilled Water Return Temperature Tertiary Chilled Water Flow Tertiary Loop Chilled Water Differential Pressure in Loop Total per Unit Tertiary Chilled Water Pump VFD Feedback 6 7 8 9 10 3 Tertiary Chilled Water Pump Run Status Tertiary Chilled Water Pump VFD Trip Tertiary Chilled Water Pump VFD Auto / Manual Tertiary Chilled Water Pump VFD Control Tertiary Chilled Water Pump Enable / Disable Total per Unit Total for all Units Total Tertiary Chilled Water System points 1 6 2 6 18 1 1 0 1 3 1 0 1 1 1 1 1 3 1 3 0-10V From Pump VFD Control Panel VFC From Pump Control Panel VFC From Pump Control Panel VFC From Pump Control Panel 0-10V DC Signal From BMS Relay Output From BMS Immersion Temperature Sensor Immersion Temperature Sensor Flow Meter(By Others) Liquid Differential Pressure Sensor 1 1 3 3 1 1 7 3 3 0 0

Point Description
Energy transfer Station (ETS)

AI
1

Required Points DI AO
1 1 1 1

DO

BACnet Network Thermostat

Software OPC Client Integration Water Flow Meter

Remarks

Liquid Differential Pressure Sensor VFC from Valve Limit Switch (valve by others) VFC from Valve Limit Switch (valve by others) Liquid Pressure Sensor Immersion Temperature Sensor

38 of 49

Project : ITTC 18 PARCELS (IT-02) Subject : BMS Input / Output List Item Qty.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 3

Point Description
Point List - Through OSP/BACnet connection (cont.) Frequency Output (in Hz) Percent Output Speed (in RPM) Current (in Amps) Torque (in %) Power(in %) Run Time hours Run/Stop Status VSD Fault Alarm Current Limit(in %) Accel Time (in sec) Decel Time(in sec) VSD speed modulate start/stop command Total per Unit Total for all Units Total Point List-Through OSP/BACnet connection (cont.)

AI
-

Required Points DI AO

DO

BACnet Network Thermostat

Software OPC Client Integration

Remarks

0 0 0 0 0 0 0 0 0

Through OSP/BACnet Connection

1 3 3

39 of 49

Project : ITTC 18 PARCELS (IT-02) Subject : BMS Input / Output List Item Qty.
FAHU( CAV ) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 2 Supply Air Temperature Outside Air Temperature Chilled water supply temperature Chilled water return temperature 2-Way Cooling Valve Position feedback Final Filter Status Pre Filter Status Supply Fan Status Supply fan air flow status Supply Fan Trip Supply Fan Auto / Manual Fresh air Damper Open / Close Feedback Exhaust air Damper Open / Close Feedback Smoke Detector 2-Way Cooling Valve Control Supply Fan Start/Stop Fresh air Damper open / close Command Exhaust air Damper open / close Command Total per Unit Total for all Units TOTAL FAHU (CAV) Points 5 10 8 16 32 1 2 1 1 1 1 1 1 1 1 1 1 1 1 0 1 1 1 1 0 2 4

Point Description

AI

Required Points DI AO

DO

BACnet Network Thermostat

Software OPC Client Integration

Remarks

40 of 49

Project : ITTC 18 PARCELS (IT-02) Subject : BMS Input / Output List Item Qty.
Fan Coil Units (FCU) 1 2 3 4 5 6 7 Return Air Temperature Air Flow Filter Status Supply Fan Status 25 Supply Fan Auto / Manual Supply Fan Air Flow Switch Supply Fan Start / Stop 2- Way Control Valve Open / Close Command Total per Unit Total for all Units Total Fan Coil Units (FCU) Points Fan Coil Units (FCU) with Electric Heater 1 2 3 4 5 6 7 8 9 10 11 Return Air Temperature Air Flow Filter Status Supply Fan Status Supply Fan Auto / Manual Supply Fan Air Flow Switch 19 Supply Fan Start / Stop 2- Way Control Valve Open / Close Command Electric Heater Status Electric Heater Current Switch Electric Heater Auto / Manual Electric Heater Start / Stop Total per Unit Total for all Units Total Fan Coil Units (FCU) with Electric Heater Points Exhaust Fans 1 2 3 4 5 17 Fan Status Fan Trip Fan Auto/Manual Fan Start/Stop Fan Air Flow Status Total per Unit Total for all Units Total Exhaust Fans Points 0 0 1 4 68 0 0 85 41 of 49 1 1 1 1 1 17 1 19 7 133 209 0 0 1 1 1 1 3 57 1 1 1 1 1 1 1 1 25 4 100 175 0 0 1 1 1 1 1 1 1 2 50

Point Description

AI

Required Points DI AO

DO

BACnet Network Thermostat

Software OPC Client Integration

Remarks

Project : ITTC 18 PARCELS (IT-02) Subject : BMS Input / Output List Item Qty.
Smoke Exhaust 1 2 3 4 1 Fan Status Fan Trip Fan Auto/Manual Fan Air Flow Status Total per Unit Total for all Units TOTAL Smoke Exhaust Fans Points Pressurization Fans 1 2 3 4 5 6 3 Fan Status Fan Trip Fan Auto/Manual Fan Air Flow Status Air Damper Open / Close Feedback Air Damper Open / Close Command Total per Unit Total for all Units Total Pressurization Fans Points 0 0 1 1 1 1 1 5 15 18 0 0 1 1 3 0 0 1 1 1 1 4 4 4 0 0 0 0

Point Description

AI

Required Points DI AO

DO

BACnet Network Thermostat

Software OPC Client Integration

Remarks

42 of 49

Project : ITTC 18 PARCELS (IT-02) Subject : BMS Input / Output List Item Qty.
Impulse Fans 1 2 3 4 Start/Stop Control 29 Contactor Status Air Flow Monitoring Motor Fail/Trip Total per Unit Total for all Units Total Impulse Fans Points Energy Recovery Unit 1 2 3 4 5 1 Fan Status Fan Trip Fan Auto/Manual Fan Start/Stop Fan Air Flow Status Total per Unit Total for all Units Total Energy Recovery Units Points 0 0 1 4 4 5 0 0 1 1 1 1 1 1 0 0 3 87 116 0 0 0 1 1 1 1 1 29 0 0

Point Description

AI

Required Points DI AO

DO

BACnet Network Thermostat

Software OPC Client Integration

Remarks

43 of 49

Project : ITTC 18 PARCELS (IT-03) Subject : BMS Input / Output List Item Qty.
1 2 3 4 5 6 1 Chilled Water Meters Differential Pressure Transmitter Motorized Valve (HX) By-Pass Motorized Valve Pressure Indicator Temperature Indicator Total per Unit Total for all Units Total ETS Points Tertiary Chilled Water System 1 2 3 5 1 Tertiary Common Chilled Water Supply Temperature Tertiary commom Chilled Water Return Temperature Tertiary Chilled Water Flow Tertiary Loop Chilled Water Differential Pressure in Loop Total per Unit Tertiary Chilled Water Pump VFD Feedback 6 7 8 9 10 3 Tertiary Chilled Water Pump Run Status Tertiary Chilled Water Pump VFD Trip Tertiary Chilled Water Pump VFD Auto / Manual Tertiary Chilled Water Pump VFD Control Tertiary Chilled Water Pump Enable / Disable Total per Unit Total for all Units Total Tertiary Chilled Water System points 1 6 2 6 18 1 1 0 1 3 1 0 1 1 1 1 1 3 1 3 0-10V From Pump VFD Control Panel VFC From Pump Control Panel VFC From Pump Control Panel VFC From Pump Control Panel 0-10V DC Signal From BMS Relay Output From BMS Immersion Temperature Sensor Immersion Temperature Sensor Flow Meter(By Others) Liquid Differential Pressure Sensor 1 1 3 3 1 1 7 3 3 0 0

Point Description
Energy transfer Station (ETS)

AI
1

Required Points DI AO
1 1 1 1

DO

BACnet Network Thermostat

Software OPC Client Integration Water Flow Meter

Remarks

Liquid Differential Pressure Sensor VFC from Valve Limit Switch (valve by others) VFC from Valve Limit Switch (valve by others) Liquid Pressure Sensor Immersion Temperature Sensor

44 of 49

Project : ITTC 18 PARCELS (IT-03) Subject : BMS Input / Output List Item Qty.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 3

Point Description
Point List - Through OSP/BACnet connection (cont.) Frequency Output (in Hz) Percent Output Speed (in RPM) Current (in Amps) Torque (in %) Power(in %) Run Time hours Run/Stop Status VSD Fault Alarm Current Limit(in %) Accel Time (in sec) Decel Time(in sec) VSD speed modulate start/stop command Total per Unit Total for all Units Total Point List-Through OSP/BACnet connection (cont.)

AI
-

Required Points DI AO

DO

BACnet Network Thermostat

Software OPC Client Integration

Remarks

0 0 0 0 0 0 0 0 0

Through OSP/BACnet Connection

1 3 3

45 of 49

Project : ITTC 18 PARCELS (IT-03) Subject : BMS Input / Output List Item Qty.
FAHU( CAV ) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 2 Supply Air Temperature Outside Air Temperature Chilled water supply temperature Chilled water return temperature 2-Way Cooling Valve Position feedback Final Filter Status Pre Filter Status Supply Fan Status Supply fan air flow status Supply Fan Trip Supply Fan Auto / Manual Fresh air Damper Open / Close Feedback Exhaust air Damper Open / Close Feedback Smoke Detector 2-Way Cooling Valve Control Supply Fan Start/Stop Fresh air Damper open / close Command Exhaust air Damper open / close Command Total per Unit Total for all Units TOTAL FAHU (CAV) Points 5 10 8 16 32 1 2 1 1 1 1 1 1 1 1 1 1 1 1 0 1 1 1 1 0 2 4

Point Description

AI

Required Points DI AO

DO

BACnet Network Thermostat

Software OPC Client Integration

Remarks

46 of 49

Project : ITTC 18 PARCELS (IT-03) Subject : BMS Input / Output List Item Qty.
Fan Coil Units (FCU) 1 2 3 4 5 6 7 Return Air Temperature Air Flow Filter Status Supply Fan Status 96 Supply Fan Auto / Manual Supply Fan Air Flow Switch Supply Fan Start / Stop 2- Way Control Valve Open / Close Command Total per Unit Total for all Units Total Fan Coil Units (FCU) Points Fan Coil Units (FCU) with Electric Heater 1 2 3 4 5 6 7 8 9 10 11 4 Return Air Temperature Air Flow Filter Status Supply Fan Status Supply Fan Auto / Manual Supply Fan Air Flow Switch Supply Fan Start / Stop 2- Way Control Valve Open / Close Command Electric Heater Status Electric Heater Current Switch Electric Heater Auto / Manual Electric Heater Start / Stop Total per Unit Total for all Units Total Fan Coil Units (FCU) with Electric Heater Points Exhaust Fans 1 2 3 4 5 29 Fan Status Fan Trip Fan Auto/Manual Fan Start/Stop Fan Air Flow Status Total per Unit Total for all Units Total Exhaust Fans Points 0 0 1 4 116 0 0 145 47 of 49 1 1 1 1 1 29 1 4 7 28 44 0 0 1 1 1 1 3 12 1 1 1 1 1 1 1 1 96 4 384 672 0 0 1 1 1 1 1 1 1 2 192

Point Description

AI

Required Points DI AO

DO

BACnet Network Thermostat

Software OPC Client Integration

Remarks

Project : ITTC 18 PARCELS (IT-03) Subject : BMS Input / Output List Item Qty.
Smoke Exhaust 1 2 3 4 1 Fan Status Fan Trip Fan Auto/Manual Fan Air Flow Status Total per Unit Total for all Units TOTAL Smoke Exhaust Fans Points Pressurization Fans 1 2 3 4 5 6 2 Fan Status Fan Trip Fan Auto/Manual Fan Air Flow Status Air Damper Open / Close Feedback Air Damper Open / Close Command Total per Unit Total for all Units Total Pressurization Fans Points 0 0 1 1 1 1 1 5 10 12 0 0 1 1 2 0 0 1 1 1 1 4 4 4 0 0 0 0

Point Description

AI

Required Points DI AO

DO

BACnet Network Thermostat

Software OPC Client Integration

Remarks

48 of 49

Project : ITTC 18 PARCELS (IT-03) Subject : BMS Input / Output List Item Qty.
Impulse Fans 1 2 3 4 Start/Stop Control 30 Contactor Status Air Flow Monitoring Motor Fail/Trip Total per Unit Total for all Units Total Impulse Fans Points Energy Recovery Unit 1 2 3 4 5 2 Fan Status Fan Trip Fan Auto/Manual Fan Start/Stop Fan Air Flow Status Total per Unit Total for all Units Total Energy Recovery Units Points 0 0 1 4 8 10 0 0 1 1 1 1 1 2 0 0 3 90 120 0 0 0 1 1 1 1 1 30 0 0

Point Description

AI

Required Points DI AO

DO

BACnet Network Thermostat

Software OPC Client Integration

Remarks

49 of 49

APPENDIX C: BUILDING MANAGEMENT SYSTEM (EE INPUT/OUTPUT LISTS)

ITCC in Riyadh Bldg KB04-KB06, IT01-IT03 & RD03-RD04 J09-07800

Divider

Project : ITCC IT01-03 BLDG Subject : BMS Input / Output List Date : 18-Oct-09 Item Qty.
1 1

Point Description 13.8 KV Switchgear Incoming Feeder line and Feeder line
Total per Unit Total for all Units Total 13.8 KV Switchgear Points

AI

Required Points DI AO

DO

BACnet Network Thermostat

Software OPC Client Integration 1 1

Remarks
MODBUS protocol integration all monitoring and measurement values

1 1

1 2

TRANSFORMER Temperature (Alarm and Tripping) Cooling Fan


Total per Unit Total for all Units Total TRANSFORMER Points 0

1 1 2 2 2 2 2 0 0 0 0 4 4 1 software integration all monitoring and measurement values software integration of Circuit Breaker control and measuring unit 0 0

Switchboard/EMPD/MDP Main breaker / Branch C.B


Total per Unit Total for all Units Total Switchboard/EMPD/MDP Points

1 2

Generator Set Genrator Set Genrator Set C.B


Total per Unit Total for all Units Total Generator Set Points 0 0 0 0

1 2 2 2 1 1 0 0 0 0 1 1 1 1 0 0 1 of 6 0 0 1 1

UPS SYSTEM UPS SYSTEM software integration


Total per Unit Total for all Units Total UPS System Points

software integration all monitoring and measurement values

FIRE ALARM SYSTEM FIRE ALARM SYSTEM software integration


Total per Unit Total for all Units Total Fire Alarm System Points

software integration only monitoring

Project : ITCC IT01-03 BLDG Subject : BMS Input / Output List Date : 18-Oct-09 Item Qty.
1 1

Point Description PUBLIC ADDRESS SYSTEM PUBLIC ADDRESS SYSTEM software integration
Total per Unit Total for all Units Total Public Address Points

AI

Required Points DI AO

DO

BACnet Network Thermostat

Software OPC Client Integration 1 1

Remarks
software integration only monitoring

1 1 1 1 software integration only monitoring

CCTV ADDRESS SYSTEM CCTV ADDRESS SYSTEM software integration


Total per Unit Total for all Units Total CCTV System Points 0 0 0 0

1 1 1 1 software integration only monitoring

ACCESS CONTROL SYSTEM ACCESS CONTROL SYSTEM software integration


Total per Unit Total for all Units Total Acess Control Points 0 0 0 0

1 1 1 1 software integration monitoring and controlling

EIB/KNX SWITCHING SYSTEM EIB/KNX SWITCHING SYSTEM software integration


Total per Unit Total for all Units Total Dali/Knx Switching System Points 0 0 0 0

1 1 1 1 software integration monitoring and controlling

CAR PARKING GUIDANCE SYSTEM CAR PARKING GUIDANCE SYSTEM software integration
Total per Unit Total for all Units Total CAR PARKING GUIDANCE SYSTEM Points 0 0 0 0

1 1

2 of 6

Project : ITCC KB04-05 BLDG Subject : BMS Input / Output List Date : 18-Oct-09 Item Qty.
1 1

Point Description 13.8 KV Switchgear Incoming Feeder line and Feeder line
Total per Unit Total for all Units Total 13.8 KV Switchgear Points

AI

Required Points DI AO

DO

BACnet Network Thermostat

Software OPC Client Integration 1 1

Remarks
MODBUS protocol integration all monitoring and measurement values

1 1

1 2

TRANSFORMER Temperature (Alarm and Tripping) Cooling Fan


Total per Unit Total for all Units Total TRANSFORMER Points 0

1 1 2 2 2 2 2 0 0 0 0 4 4 1 software integration all monitoring and measurement values software integration of Circuit Breaker control and measuring unit 0 0

Switchboard/EMPD/MDP Main breaker / Branch C.B


Total per Unit Total for all Units Total Switchboard/EMPD/MDP Points

1 2

Generator Set Genrator Set Genrator Set C.B


Total per Unit Total for all Units Total Generator Set Points 0 0 0 0

1 2 2 2 1 1 0 0 0 0 1 1

FIRE ALARM SYSTEM FIRE ALARM SYSTEM software integration


Total per Unit Total for all Units Total Fire Alarm System Points

software integration only monitoring

3 of 6

Project : ITCC KB04-05 BLDG Subject : BMS Input / Output List Date : 18-Oct-09 Item Qty.
1 1

Point Description PUBLIC ADDRESS SYSTEM PUBLIC ADDRESS SYSTEM software integration
Total per Unit Total for all Units Total Public Address Points

AI

Required Points DI AO

DO

BACnet Network Thermostat

Software OPC Client Integration 1 1

Remarks
software integration only monitoring

1 1 1 1 software integration only monitoring

CCTV ADDRESS SYSTEM CCTV ADDRESS SYSTEM software integration


Total per Unit Total for all Units Total CCTV System Points 0 0 0 0

1 1 1 1 software integration only monitoring

ACCESS CONTROL SYSTEM ACCESS CONTROL SYSTEM software integration


Total per Unit Total for all Units Total Acess Control Points 0 0 0 0

1 1 1 1 software integration monitoring and controlling

EIB/KNX SWITCHING SYSTEM EIB/KNX SWITCHING SYSTEM software integration


Total per Unit Total for all Units Total Dali/Knx Switching System Points 0 0 0 0

1 1 1 1 software integration monitoring and controlling

CAR PARKING GUIDANCE SYSTEM CAR PARKING GUIDANCE SYSTEM software integration
Total per Unit Total for all Units Total CAR PARKING GUIDANCE SYSTEM Points 0 0 0 0

1 1

4 of 6

Project : ITCC RD03-04 BLDG Subject : BMS Input / Output List Date : 18-Oct-09 Item Qty.
1 1

Point Description 13.8 KV Switchgear Incoming Feeder line and Feeder line
Total per Unit Total for all Units Total 13.8 KV Switchgear Points

AI

Required Points DI AO

DO

BACnet Network Thermostat

Software OPC Client Integration 1 1

Remarks
MODBUS protocol integration all monitoring and measurement values

1 1

1 2

TRANSFORMER Temperature (Alarm and Tripping) Cooling Fan


Total per Unit Total for all Units Total TRANSFORMER Points 0

1 1 2 2 2 2 2 0 0 0 0 4 4 1 software integration all monitoring and measurement values software integration of Circuit Breaker control and measuring unit 0 0

Switchboard/EMPD/MDP Main breaker / Branch C.B


Total per Unit Total for all Units Total Switchboard/EMPD/MDP Points

1 2

Generator Set Genrator Set Genrator Set C.B


Total per Unit Total for all Units Total Generator Set Points 0 0 0 0

1 2 2 2 1 1 0 0 0 0 1 1 1 1 0 0 5 of 6 0 0 1 1

UPS SYSTEM UPS SYSTEM software integration


Total per Unit Total for all Units Total UPS System Points

software integration all monitoring and measurement values

FIRE ALARM SYSTEM FIRE ALARM SYSTEM software integration


Total per Unit Total for all Units Total Fire Alarm System Points

software integration only monitoring

Project : ITCC RD03-04 BLDG Subject : BMS Input / Output List Date : 18-Oct-09 Item Qty.
1 1

Point Description PUBLIC ADDRESS SYSTEM PUBLIC ADDRESS SYSTEM software integration
Total per Unit Total for all Units Total Public Address Points

AI

Required Points DI AO

DO

BACnet Network Thermostat

Software OPC Client Integration 1 1

Remarks
software integration only monitoring

1 1 1 1 software integration only monitoring

CCTV ADDRESS SYSTEM CCTV ADDRESS SYSTEM software integration


Total per Unit Total for all Units Total CCTV System Points 0 0 0 0

1 1 1 1 software integration only monitoring

ACCESS CONTROL SYSTEM ACCESS CONTROL SYSTEM software integration


Total per Unit Total for all Units Total Acess Control Points 0 0 0 0

1 1 1 1 software integration monitoring and controlling

EIB/KNX SWITCHING SYSTEM EIB/KNX SWITCHING SYSTEM software integration


Total per Unit Total for all Units Total Dali/Knx Switching System Points 0 0 0 0

1 1 1 1 software integration monitoring and controlling

CAR PARKING GUIDANCE SYSTEM CAR PARKING GUIDANCE SYSTEM software integration
Total per Unit Total for all Units Total CAR PARKING GUIDANCE SYSTEM Points 0 0 0 0

1 1

6 of 6

APPENDIX D: 40-SDMS-02 REV. 5 SPECIFICATION FOR KILO-WATT-HOUR METER

ITCC in Riyadh Bldg KB04-KB06, IT01-IT03 & RD03-RD04 J09-07800

Divider

Saudi Electricity Company


SEC DISTRIBUTION MATERIALS SPECIFICATION


40-SDMS-02 REV. 05 DATE: 03 February 2007

40-SDMS-02 REV. 05 SPECIFICATIONS FOR


ELECTRONIC KILO-WATT-HOUR METER

This specification is property of SEC and subject to change or modification without any notice

Saudi Electricity Company


SEC DISTRIBUTION MATERIALS SPECIFICATION


40-SDMS-02 REV. 05 DATE: 03 February 2007

CONTENTS
Clause
1.0 2.0 3.0 4.0 5.0 6.0 7.0 8.0 9.0 10.0 11.0 12.0 13.0 14.0 15.0 16.0 17.0 18.0 19.0 20.0

Description
SCOPE CROSS REFERENCES APPLICABLE CODES AND STANDARDS SERVICE CONDITIONS SYSTEM PARAMETERS DESIGN AND CONSTRUCTION ELECTRICAL REQUIREMENTS ACCURACY CALIBRATION INPUT AND OUTPUT REQUIREMENTS FUNCTIONAL REQUIREMENTS DEFAULT SETTINGS PERIPHERAL DEVICES SUPPORT SYSTEM REQUIREMENTS MARKING OF METERS PACKING GUARANTEE SUBMITTALS TESTING TECHNICAL DATA SCHEDULE

Page
4 4 4 6 6 7 8 9 10 10 14 20 22 22 26 28 28 29 30 32

Page 2 of 40

Saudi Electricity Company


SEC DISTRIBUTION MATERIALS SPECIFICATION


40-SDMS-02 REV. 05 DATE: 03 February 2007

LIST OF DRAWINGS
Drawing No.
SEC/KWH-S-01 SEC/KWH-S-02

Description
OVERALL AND MOUNTING DIMENSIONS CONNECTION ARRANGEMENT FOR 3-PHASE 4-WIRE WHOLE CURRENT 127/220V & 220/380V METER CONNECTION ARRANGEMENT FOR 3-PHASE 4-WIRE CT OPERATED 127/220V OR 220/380V METER CONNECTION ARRANGEMENT FOR 3-PHASE 3-WIRE CT - VT OPERATED 110V METER DISPLAY ARRANGEMENT

Page
37 38

SEC/KWH-S-03

39

SEC/KWH-S-04

40

SEC/KWH-S-05

41

Page 3 of 40

Saudi Electricity Company


SEC DISTRIBUTION MATERIALS SPECIFICATION


40-SDMS-02 REV. 05 DATE: 03 February 2007

1.0

SCOPE This SEC Distribution Materials Specification (SDMS) describes the minimum technical requirements for design, materials, manufacturing, inspection, performance and supply of programmable electronic kilowatt-hour (kWh) meters, intended to be used for revenue metering in the distribution system of Saudi Electricity Company (SEC). This specification also describes the technical requirements for the electronic kWh meters to be used in an Automatic Meter Reading System (AMR).

2.0 2.1

CROSS REFERENCES This specification shall be read in conjunction with SEC General Specification No. 01-SDMS-01 (latest revision) titled General Requirements for all Equipments/Materials which shall be considered as an integral part of this specification. This Specification shall also be read in conjunction with SEC purchase order requirements. APPLICABLE CODES AND STANDARDS The latest revision of the following codes and standards shall be applicable for the equipment / material covered by this specification. In case of any deviation, the Vendor / Manufacturer may propose equipment / material conforming to equivalent alternate codes and standards. However, the provisions of SEC standards shall supersede the provisions of these standards in case of any conflict. IEC-62053-21 IEC-61037 IEC-61038 IEC-62053-22 Electricity metering equipment (a.c.) - static meters for active energy (classes 1 and 2). Electricity metering Tariff and load control Particular requirements for electronic ripple control receivers. Electricity metering Tariff and load control - Particular requirements for time switches. Electricity metering equipment (a.c.) - static meters for active energy (classes 0.2 S and 0.5 S).

2.2 3.0

Page 4 of 40

Saudi Electricity Company


SEC DISTRIBUTION MATERIALS SPECIFICATION


40-SDMS-02 REV. 05 DATE: 03 February 2007

IEC-62053-23 IEC-61268 IEC-60514 IEC-62054-11

Electricity metering equipment (a.c.) - static meters for reactive energy (classes 2 and 3). Alternating current static watt-hour-meters for reactive energy (classes 1 and 2). Acceptance inspection of Class 2 alternating-current watthour meters. Electricity metering - Data exchange for meter reading, tariff and load control Particular requirements for electronic ripple control receivers. Electricity metering - Data exchange for meter reading, tariff and load control Direct local data exchange. Electricity metering - Data exchange for meter reading, tariff and load control Interface classes. Electricity metering - Data exchange for meter reading, tariff and load control Physical layer. Electricity metering - Data exchange for meter reading, tariff and load control Data link layer. Electricity metering - Data exchange for meter reading, tariff and load control COSEM transport layers for IP networks. Electricity metering - Data exchange for meter reading, tariff and load control COSEM Application layer. Electricity metering - Data exchange for meter reading, tariff and load control Object identification system (OBIS). Distribution Automation Using Distribution Line Carrier Systems Part4. Electricity metering Data exchange for meter reading, tariff and load control, Use of local area networks on twisted pair with carrier signaling.

IEC-62056-21 IEC-62056-62 IEC-62056-42 IEC-62056-46 IEC-62056-47 IEC-62056-53 IEC-62056-61 IEC-61334-4-41 IEC-62056-31

Page 5 of 40

Saudi Electricity Company


SEC DISTRIBUTION MATERIALS SPECIFICATION


40-SDMS-02 REV. 05 DATE: 03 February 2007

IEC-62357

Power system control and associated communications Reference architecture for object models, services and protocols. Teleprotection equipment of power systems Performance and testing Command systems. Insulation coordination within Low Voltage System including clearances and creepage distance for equipments. Fire hazard testing part-2 test methods glow wire test and guidance. Spring operated impact tests apparatus test and its calibration. Test requirements of Terminal Blocks. Thermosetting Resins. Polycarbonate Resins.

IEC-62834-1 IEC-60664 IEC-60695-2-10 IEC-60817-1987 IEC-60947-7-1 ASTM D-4098 ASTM D-3935 4.0

SERVICE CONDITIONS The meter will be installed indoor and/or outdoor as referred to the latest revision of SEC General Specification No. 01-SDMS-01. In outdoor installations, the meter shall be enclosed in weatherproof fiberglass meter box. The air temperature inside the meter box may be regarded as 75C due to direct solar radiation, plus the effect of any internal heating. Temperature range: Limit range for storage and transportation Limit range for operation -10C to 85C -10C to 70C

5.0

SYSTEM PARAMETERS The meter shall be suitable for operation in SEC distribution system conditions as per the latest revision of SEC General Specification No.01-SDMS-01. The meter shall be deemed to meet the requirements without any adverse effect over the life cycle.

Page 6 of 40

Saudi Electricity Company


SEC DISTRIBUTION MATERIALS SPECIFICATION


40-SDMS-02 REV. 05 DATE: 03 February 2007

6.0 6.1

DESIGN AND CONSTRUCTION Case 6.1.1 6.1.2 The case of the meter shall be made of nonmetallic material. It shall be made of phenol or high-grade polycarbonate resin. The meter shall have an adequate dust proof and moisture proof case, which can be sealed in such a way that the internal parts of the meter are accessible only after breaking the seals. The degree of protection shall be IP51. Top and bottom mountings shall be metallic with anti rust coating. Thickness of these mountings shall not be less than 1.5 mm bolted / riveted to the meter case. Plastic mountings may also be acceptable provided the thickness of the mountings is enough to withstand the mounting pressure. Adequate sealing provision shall be provided in different parts of the meter, i.e., terminal cover, meter cover and battery cover if used. The overall and mounting dimensions and top & bottom mounting arrangements shall be provided similar to the sketch as given in drawing No. SEC/KWH-S-01. All the screws used in the meter shall be of slotted head type only except the screws used for the internal assembly of meter parts.

6.1.3

6.1.4 6.1.5

6.1.6 6.2

Terminals and Terminal Block 6.2.1 The terminals shall be grouped in a terminal block of adequate insulating properties and mechanical strength. They shall be arranged for bottom connection. For whole current meters, it shall be possible to disconnect easily but not accidentally the relevant voltage terminals from the input current terminals by means of any suitable type voltage links. The voltage links shall be either inside the meter cover or under a separate sealed cover. An additional fixed voltage screw with side-grooved head shall be extended from voltage link to terminal block in order to connect voltage test lead easily during testing of the meter in the SEC laboratory.

6.2.2

Page 7 of 40

Saudi Electricity Company


SEC DISTRIBUTION MATERIALS SPECIFICATION


40-SDMS-02 REV. 05 DATE: 03 February 2007

6.2.3

The terminals shall be suitable for copper conductors and provided with minimum of two screws for each conductor. The bore diameter for phase and neutral terminals shall be as given in Table No. 1 below. Table No. 1 kWh-meters Terminals bore diameter (mm) 9 - 12 4.5 - 5 Conductor size 35 mm soft drawn stranded copper 2.5 mm soft drawn single stranded copper

Whole Current CT & CT-VT operated 6.2.4 6.3

The terminal block shall include additional connection terminals for the communication interfaces and output relay.

Terminal Cover Terminal cover shall be made of the same materials as that of the meter case and sealed independently of the meter cover. The terminal cover shall include information indicating the correct phase sequence and connections as per drawing No. SEC/KWH-S-02, 03 and 04.

6.4

Meter Cover 6.4.1 6.4.2 The cover of the meter shall be made of opaque, shatterproof, ultra violet stabilized nonmetallic material with a clear glass or polycarbonate window. The clear window shall be large enough to view the display and the nameplate details and insured transparency during the whole service life of the meter. The meter cover shall have enough room to provide the optical port, display push-button, reset push-button and optical test outputs. These components shall be arranged either within or outside the window area.

6.4.3

7.0 7.1

ELECTRICAL REQUIREMENTS All electrical requirements shall be referred to SEC General Specification No. 01SDMS-01.
Page 8 of 40

Saudi Electricity Company


SEC DISTRIBUTION MATERIALS SPECIFICATION


40-SDMS-02 REV. 05 DATE: 03 February 2007

7.2

Nominal / basic current (Ib), rated maximum current (Imax) and reference voltages shall be as given in Table No. 2. Table No. 2 Kilowatt-hour meter type Whole Current CT operated CT-VT operated Current rating in Amps (Ib) (Imax) 10 20 1.5 100 160 6 Reference voltage in Volts Dual 127/220 & 220/380 127/220 OR 220/380 110

7.3

The power measuring elements for Whole Current, CT and CT-VT operated meters shall be as given in Table No. 3. Table No. 3 Kilowatt-hour meter Type Whole Current CT operated CT-VT operated Number of measuring elements 3 2 Kilowatt-hour meter connections 3 Phase 4 wire 3 Phase 3 wire

7.4

The temperature rise at any point of the electrical circuit, insulation and the external surface of the meter shall not exceed 30C with an ambient temperature not exceeding 55C. The meter shall have a fully redundant power supply; i.e. withstanding any phaseneutral inversion, missing phases or missing neutral. ACCURACY The Accuracy class index of the meter shall be Class 1 for whole current meters and Class 1 or better for CT and CT-VT operated meters. The whole current meter shall be designed and calibrated for wide voltage range application and the meter name plate shall indicate only the two operating voltages of the SEC LV Distribution network as mentioned in table No.2.
Page 9 of 40

7.5 8.0 8.1 8.2

Saudi Electricity Company


SEC DISTRIBUTION MATERIALS SPECIFICATION


40-SDMS-02 REV. 05 DATE: 03 February 2007

9.0

CALIBRATION Every meter shall be calibrated for error limits as per IEC 62053-21 and IEC 6205323.

10.0 10.1

INPUT AND OUTPUT REQUIREMENTS Display 10.1.1 The display shall be of a high contrast and easy to read Liquid Crystal Display (LCD) offers a wide array of information and flexibility. 10.1.2 The LCD shall withstand SEC environmental conditions specified in 01SDMS-01 latest revision and shall not have any change in color, contrast or brightness during the entire meter life period. The temperature limit range of operation for the LCD is the same as that of the meter as mentioned in clause 4.0. 10.1.3 For whole current meters, the display shall be of a standard LCD with multisegment. For CT & CT-VT operated meters legends/dimensions as shown in the drawing No. SEC/KWH-S-05 or any other similar LCD which provides equivalent text/legend information. 10.1.4 The display shall have access to all the metering parameters as given in the functional requirements and shall be tailored to display only the required information by masking-out undesired information. 10.1.5 The number of digits for displaying the energy registers (clause 11.1) shall be configurable with a minimum of 8 digits and pre-configured by the manufacturer to display 6 digits without any decimal for whole current meters and 5 digits without any decimal for CT and CT-VT operated meters. For all energy registers the leading zeros shall be displayed. 10.1.6 The minimum height and width of the CT & CT-VT operated meters display/digits for displaying different display parameters shall be as shown in drawing No. SEC/KWH-S-05. 10.1.7 For Item No.9 of drawing No. SEC/KWH-S-05, if the meter displays the OBIS code only, then a table containing a short description of the codes shall be fixed on the front panel.

Page 10 of 40

Saudi Electricity Company


SEC DISTRIBUTION MATERIALS SPECIFICATION


40-SDMS-02 REV. 05 DATE: 03 February 2007

10.1.8 The display shall also provide the following whenever it is required: 10.1.8.1 A register value with its appropriate unit, multiplication factor and description or DLMS/COSEM/OBIS code of the parameter of which the register is storing. 10.1.8.2 A tariff number indicates which tariff period is in view. 10.1.8.3 A 3-Phase status indicator remains static throughout the operation and goes off if the corresponding phases trip. 10.1.8.4 An anomaly indicator flashes when there is failure in the electronic components, overflow in calculation or any other error which results in meter malfunction. 10.1.8.5 A reverse direction indicator flashes when the active energy in one or more of the phases is flowing in the reverse (export) direction. (Alternately a four quadrant indicator is also acceptable provided it shall flash when the measured active energy in one or more of the phases is in the export direction). 10.1.8.6 A battery low indicator flashes when the battery is required replacement. 10.1.8.7 A communication indicator is lighted when the meter is communicating through one of its communication ports. 10.2 Optical test output 10.2.1 The meter shall have one or two optical test output devices capable of being monitored with suitable testing equipment. The optical output value, i.e., the meter constant in terms of Imp/kWh and Imp/kVARh shall be inscribed on the front panel of the meter. 10.2.2 If only one optical test output is used for both kWh and kVARh, it shall be possible to choose the required one while testing the meter in the site or laboratory. 10.2.3 The requirements of optical test outputs are according to IEC 62052-11.

Page 11 of 40

Saudi Electricity Company


SEC DISTRIBUTION MATERIALS SPECIFICATION


40-SDMS-02 REV. 05 DATE: 03 February 2007

10.3

Local Communication Interface 10.3.1 Optical Interface 10.3.1.1 The meter shall have an infrared optical interface module to enable the use of a RS-232 / USB compatible optical probe (See Clause 13.2) in compliance with IEC-62056-21 (previously IEC 61107) or latest version. 10.3.1.2 The optical port shall allow bi-directional communication with a Hand Held Unit (HHU) or IBM compatible PC for rapid, error free electronic data transfer using the DLMS/COSEM protocol as well as IEC 62056-21 (See Clause 13.2). 10.3.1.3 The optical port shall be used to configure the meter, read all the register values and load profile data. 10.3.2 Additional Local Interfaces 10.3.2.1 The whole current meters & CT operated meters shall have Euridis interface as per EURIDIS (IEC62056-31) standard, in order to connect the meter with an external (PLC/PSTN/GSM/GPRS/RF/ETHERNET) modem (see clause 10.4.1). 10.3.2.2 The same EURIDIS interface shall also communicate with other Euridis Meters and Meter Interface Unit (MIU). 10.3.2.3 The connections for EURIDIS ports shall be provided in the terminal block.

10.4

Remote Communication Interface 10.4.1 The whole current meters and CT operated meters shall not be equipped with any modem for remote communication at the initial stage but the meters shall be designed in such a way to accommodate internally/ externally a (PLC/PSTN/GSM/GPRS/RF/ETHERNET) modem (possibly a pluggable type) at a later stage without changing the hardware and firmware of the meter. This modem is required when the meter is placed in an AMR system at a later stage.

Page 12 of 40

Saudi Electricity Company


SEC DISTRIBUTION MATERIALS SPECIFICATION


40-SDMS-02 REV. 05 DATE: 03 February 2007

10.4.2 The CT-VT operated meters shall have a built in type (or possibly a pluggable type) of either an analogue PSTN, GSM or GPRS modem. The name-plate of the meter shall indicate the presence and type (PSTN/GSM/GPRS) of modem. SEC purchase order will state the breakup quantities of meters with each modem. The telephone connection for the PSTN modem shall be provided in the terminal block. 10.4.3 The telephone modem shall communicate successfully through the PSTN (Public switched telephone network) in the Kingdom of Saudi Arabia. 10.4.4 When the meter is installed in any AMR system environment, this remote communication shall permit reading of registers, load profile, and configuring the meter parameters according to the DLMS regulations. 10.5 Protocol 10.5.1 All types of meters shall be designed to use DLMS/COSEM protocol. However, the whole current and CT operated meters shall be designed to use EURIDIS/PLAN protocol based on the relevant IEC standards. 10.5.2 Any meter reading software based on DLMS/COSEM shall be able to successfully communicate with any DLMS/COSEM meter locally and remotely. This Software shall be provided with the meter manufacturer identification key and security attributes. 10.5.3 All meter types shall be certified by DLMS User and Euridis Associations for test and conformance. 10.6 Output Relay 10.6.1 The meter shall have an internally operating output relay whose contacts (C & NO) rated at 250V/1A shall be available at the terminal block. 10.6.2 The meter shall operate the output relay automatically if the current exceeds the trip point and stay there for more than a delay time. 10.6.3 The relay shall switch off if the current falls below the trip point and stay there for the same delay time. 10.6.4 The trip point which is in percentage of the basic current of a meter and the delay time in minutes shall be configurable.
Page 13 of 40

Saudi Electricity Company


SEC DISTRIBUTION MATERIALS SPECIFICATION


40-SDMS-02 REV. 05 DATE: 03 February 2007

11.0

FUNCTIONAL REQIUREMENTS The meter shall contain the following features, any combination of which can be selected to provide the required metering functions. Some features shall be configured by the vendor and the others shall be configured by the user.

11.1

Basic Energy Measurement 11.1.1 Three independent energy registers shall be used to measure total import kWh (P+), total import kVARh (Q+) and total kVAh (S). 11.1.2 Detect and measure the reverse energy and flash the reverse energy indicator if the reverse (export) energy measured is greater than the meters starting threshold. The measurements shall be stored in total export kWh (P-) and total export kVARh (Q-) registers. 11.1.3 For whole current and CT-operated meters (3 Phase 4 Wire type) the energy measurements shall be carried out separately for 3 phases and added to the relevant import or export energy registers. 11.1.4 The total kWh register is stored internally to 2 decimal places in whole current meters and 3 decimal places in CT and CT-VT operated meters. 11.1.5 The number of digits to be displayed for these 5 energy registers mentioned in clause 11.1.1 and 11.1.2 are as per the configured value (See clause 10.1.5) when the meter is operating at normal condition. It shall be selected via the display push-button as mentioned in clause 11.9.4 or via some other easy way to display these energy registers with all decimal places for testing purposes. 11.1.6 For CT and CT-VT operated meters the CT ratio and VT ratio shall be configurable. The meter shall calculate and use an appropriate multiplication factor in accordance with the CT and VT ratio. The multiplication factor shall be in terms of 1, 10, 100 or 1000 etc., with a default value of 1. The meter shall measure and store all the energy, demand and load profile values based on primary of the CT and VT only. 11.1.7 For whole current meters kVARh and kVAh measurements are not mandatory.

Page 14 of 40

Saudi Electricity Company


SEC DISTRIBUTION MATERIALS SPECIFICATION


40-SDMS-02 REV. 05 DATE: 03 February 2007

11.2

Tariff Measurement 11.2.1 A minimum of 4 tariff periods shall be used to accept inputs from the five energy registers specified in clause 11.1. 11.2.2 Each tariff period is independently time controlled using a 24-hour clock so that registration takes place over a restricted period of time. The time control shall have provision to exclude days like weekends and holidays. The tariff period which is active at a given time shall be displayed. 11.2.3 The number of digits to be displayed and the multiplication factor for tariff registers are the same as that of energy registers.

11.3

Demand Measurement 11.3.1 Three demand registers (optional for whole current meters) to measure the average demand in kW, kVAR and kVA. The demand calculations are based on either block method or sliding window method, which shall be configurable. A configurable integration time of 15, 30 or 60 minutes for both methods and a fixed sub interval of 5 minutes for the sliding method shall be used. 11.3.2 Three maximum demand registers used to store the highest value in each of the demand registers. 11.3.3 The time and date of occurrence of the maximum demand shall be recorded.

11.4

Reset Function and Historical Data Recording 11.4.1 The reset shall be carried through one of the following ways. a) Manually by pressing the front panel reset push-button. b) On command from the HHU or PC via the optical communication port. c) On command via the remote communication interface. d) Automatically, under control of the meter internal clock, at specific configurable predetermined time.

Page 15 of 40

Saudi Electricity Company


SEC DISTRIBUTION MATERIALS SPECIFICATION


40-SDMS-02 REV. 05 DATE: 03 February 2007

11.4.2 The manual and automatic reset options can be enabled/disabled through configuring the meter. Enabling the manual reset shall disable the automatic reset and vice versa. 11.4.3 The manual reset shall be carried out by pressing the reset push-button after breaking the sealing of reset button. 11.4.4 If automatic reset is being used and the power supply has failed at the specified time, then the reset may occur immediately following the return of the power supply. 11.4.5 On every reset all the registered data specified in clauses 11.1, 11.2, 11.3.2 and 11.3.3 along with the date and time of reset shall be transferred to historical registers storage. The maximum demand registers shall be reset to zero after transferring the data to the historical registers. 11.4.6 The meter shall retain the historical register data for at least the last four reset periods. 11.5 Load Profile Recording 11.5.1 The meter shall be able to record the 3 demand registers given in clause 11.3.1 at the end of every demand integration period. One or more of the 3 demand registers can be selected for load profile recording through meter configuration. The default recording shall be for demand kW and Demand kvar as given in clause 12.1. 11.5.2 Each demand value shall be identifiable to its respective date and time. The end of the last demand period in a day shall match with 00:00 hrs. 11.5.3 The meter shall have sufficient memory capacity to store one demand register value every 30 minutes for at least 120 days. When the storage is full, the new data shall overwrite the oldest stored data. 11.5.4 Load profile recording is not mandatory for whole current meters. 11.6 Real Time Clock and Calendar 11.6.1 The meter shall be equipped with a highly reliable quartz controlled real time clock / calendar which generates signals for the switching of various tariffs, automatic reset and integration period for demand and load curves.
Page 16 of 40

Saudi Electricity Company


SEC DISTRIBUTION MATERIALS SPECIFICATION


40-SDMS-02 REV. 05 DATE: 03 February 2007

11.6.2 Meter Clock shall automatically synchronize with the AMR System Clock. 11.6.3 The clock shall use the notation 00:00 to 23:59. The calendar shall be correct for meter service life and automatically cater for leap year. 11.6.4 A suitable battery or Super Capacitor shall support the real time clock in the event of power failure. The battery should offer back-up power for at least 5year continuous operation and 1 year continuous operation after 10 years storage. 11.6.5 The battery shall not be soldered directly to the hardware and be able to be replaced in the field without breaking the seal of the meter cover. 11.6.6 In case of battery failure the battery low indicator in the display shall be flashed. 11.7 Data Retention 11.7.1 All programmed/configured and registered data shall be retained in a nonvolatile memory. The meter shall employ a memory that offers a minimum of 10 years of data retention during power failure. 11.7.2 The meter memory shall also be used to record the following security data that may be displayed / read through the communication ports on request. 1. An 8-digit serial number of the meter as indicated in the name-plate, which should not be changed or erased at any cost. 2. Number of times the meter has been configured. 3. Date and time of last configuration. 4. Number of times the meter has been powered down. 5. Date and time of last power down. 6. Number of resets. 7. Date and time of last reset. 8. Date of battery install. 9. Date and time of battery fail. 10. Date and time of last reverse run. 11. Date and time of last phase loss. 11.7.3 All register data may be written into the memory at least once per day, and whenever power failure occurs.

Page 17 of 40

Saudi Electricity Company


SEC DISTRIBUTION MATERIALS SPECIFICATION


40-SDMS-02 REV. 05 DATE: 03 February 2007

11.7.4 The non-volatile memory shall be capable of being read by external equipment via contacts at the edge of the circuit board in the event of damage or component failure, which renders the meter inoperable. 11.8 Instantaneous Measurements The meter shall measure and display the instantaneous value of the following parameters. It shall be the secondary values in case of CT and CT-VT operated meters. 1. 2. 3. 4. 5. 11.9 3 Ph N Voltages (Ph Ph Voltages for 3 Ph. 3 Wire meters). 3 Phase currents (2 currents for 3 Ph. 3 Wire meters). Power factor. Power. Frequency.

Display Function 11.9.1 At normal operating condition the display should show only the first item in the display list and the phase status indicator as the default display. The total kWh register is the default first item in the display list. The default display list is given clause 12.2. The meter should not toggle the display on its own unless there is any failure to indicate. 11.9.2 A momentary press of the display push-button shall cause the display to advance to the next display in the display list. The meter shall revert to its default display after 5 seconds period of button inactivity. 11.9.3 Pressing and holding the display push-button for more than 2 seconds and releasing it cause the display automatically sequence through the display list. Each register in the display list shall be visible for 1 second. 11.9.4 Pressing and holding the display push-button for more than 5 seconds and releasing it cause the display to go to the dial test mode in which the display show all the energy registers sequentially with all decimal places as mentioned in clause 11.1.3 and 11.1.4. The meter shall revert to its default display after 5 seconds period of button inactivity. 11.9.5 As an alternate all the above-mentioned display functions may be obtained through some other user-friendly method using two buttons.

Page 18 of 40

Saudi Electricity Company


SEC DISTRIBUTION MATERIALS SPECIFICATION


40-SDMS-02 REV. 05 DATE: 03 February 2007

11.9.6 The following shows the full list of all the registers (some of them are not applicable for whole current meters) that can be displayed. In normal operation, many of these parameters would be masked out. Only the registers given in the display list are displayed on pressing the display pushbutton. The display list shall be configurable. 1. Total kWh 2. Total kVARh 3. Total kVAh 4. Total kWh export 5. Total kVARh export 6. Tariff registers (period1) 7. Tariff registers (period2) 8. Tariff registers (period3) 9. Tariff registers (period4) 10. Demand kW 11. Demand kVAR 12. Demand kVA 13. Maximum demand kW 14. Date of maximum demand kW 15. Time of maximum demand kW 16. Maximum demand kVAR 17. Date of maximum demand kVAR 18. Time of maximum demand kVAR 19. Maximum demand kVA 20. Date of maximum demand kVA 21. Time of maximum demand kVA 22. VT ratio 23. CT ratio 24. Voltage V1 (V12 for CT-VT operated meters) 25. Voltage V2 (V23 for CT-VT operated meters) 26. Voltage V3 (V31 for CT-VT operated meters) 27. Current I1 28. Current I2 (Not applicable for CT-VT operated meters) 29. Current I3 30. Power factor 31. Power kW 32. Frequency 33. Meter serial number 34. Date of battery install 35. Date of last reset
Page 19 of 40

Saudi Electricity Company


SEC DISTRIBUTION MATERIALS SPECIFICATION


40-SDMS-02 REV. 05 DATE: 03 February 2007

36. Time of last reset 37. Demand integration period 38. Date 39. Time 11.10 Security access The meter shall be provided with 3 different programmable security codes for programming/Configuring the meter, reading the data from the meter and reset. 11.11 Anti-tampering / Anti-fraud The meter shall have Anti-tampering/Anti-fraud functions that has indication and registration locally in the meter and can be transferred to any other device in the AMR system. 12.0 12.1 DEFAULT SETTINGS All the meters delivered to SEC store should have the following default settings as given in Table No.4. Table No. 4 Configuration Features Clock Tariff register Tariff period 1 Tariff period 2 Reset option From 12:00 to 17:00 From 17:00 to Next day 12:00
Push Button

Default Setting KSA Standard time (GMT + 3.00)

/ /

Automatic

Automatic reset date Demand integration method Demand integration time Load profile recording

1st day of every month at 00:00 hrs. Block 30 Minutes Demand kW & Demand kvar Sliding Window

Page 20 of 40

Saudi Electricity Company


SEC DISTRIBUTION MATERIALS SPECIFICATION


40-SDMS-02 REV. 05 DATE: 03 February 2007

CT ratio VT ratio No. of digits for display of energy registers Display list 12.2

--Whole current meter 6 digits CT & CT-VT meter 5 digits Default display list (clause 12.2)

The default display list (some of them are not applicable for whole current meters) shall be in the same sequential order as given below. 1. Total kWh 2. Date 3. Time 4. Total kvarh 5. Total kVAh 6. Total kWh export 7. Total kVARh export 8. VT ratio (Applicable for CT-VT operated meters only) 9. CT ratio 10. Voltage V1 (V12 for CT-VT operated meters) 11. Voltage V2 (V23 for CT-VT operated meters) 12. Voltage V3 (V31 for CT-VT operated meters) 13. Current I1 14. Current I2 (Not applicable for CT-VT operated meters) 15. Current I3 16. Power 17. Power factor 18. Frequency 19. Demand kW 20. Demand kVAR 21. Demand kVA 22. Demand integration time 23. Maximum demand kW 24. Date of maximum demand kW 25. Time of maximum demand kW

Page 21 of 40

Saudi Electricity Company


SEC DISTRIBUTION MATERIALS SPECIFICATION


40-SDMS-02 REV. 05 DATE: 03 February 2007

13.0

PERIPHERAL DEVICES

13.1

Hand Held Unit (HHU) The Hand Held Unit shall be commonly available and compatible with any meter reading software that operates with DLMS/COSEM protocol. The HHU shall communicate with any meter that conforms to DLMS UA. The HHU shall include a RS232 or USB data cable to communicate with the PC.

13.2

Optical Probe The optical probe shall be used to transfer data to and from the meter. The probe shall have an optical head on one end to interface with the meter and a 9 pin Dconnector or an USB connector on the other end to connect either to the HHU or directly the PC. The communication through optical probe shall conform to DLMS protocol as well as IEC-62056-21 Data Exchange for Meter Reading, Tariff and Load Control.

13.3
14.0

SEC purchase order will state the quantities of HHU and optical probe to be supplied by the vendor / manufacturer.
SUPPORT SYSTEM REQUIREMENTS

14.1

Software 14.1.1 The software shall be a package of one or more software to run under Pentium III or latter PC. The software shall have the following features. Windows NT/2000/XP based Multiple DBMS (Oracle, SQL Server) Client/Server 3-Tier model Scalable Design with Plug-in Modules 14.1.2 The Software Package shall consist of more than one module that cover (but not limited) the followings: a) b) c) d) e) f) Monitoring / reading Control / operation Diagnostic / troubleshooting / setting / configuration HHU interface Security privilege Billing interface
Page 22 of 40

Saudi Electricity Company


SEC DISTRIBUTION MATERIALS SPECIFICATION


40-SDMS-02 REV. 05 DATE: 03 February 2007

14.1.3 The software shall be a user friendly, menu driven and have options to use a variety of Hand Held Units. 14.1.4 The software shall have provisions to create user and configure different access levels for the user. 14.1.5 The software shall allow the user to create a consumer data bank grouped into area wise. Each consumer shall be identifiable by a name, consumer number, meter number, telephone number for remote communication and mode of communication. 14.1.6 The software shall allow the user to select the communication from one of the 3 options i.e., the optical port of the meter, the HHU and the remote communication through modem and/or data collection point. 14.1.7 Communication with the meter means it may either configuring the meter, reading the selected register data from the meter or reading the load profile data from the meter. 14.2 Configuring the Meter 14.2.1 Configuring the meter shall be possible through all the communication means given in clause 14.1.6. 14.2.2 Configuring the meter shall be controlled locally via access code/password and remotely via security privilege. 14.2.3 This option shall allow the user to configure the meter from a preset list of Configuration features called Configuration scheme. The list of Configuration features is given in Table No.4. 14.2.4 The Configuration features of the meter may be displayed on one or more dialogue boxes through which one can select the required features and store in the Configuration scheme. One of the many-stored Configuration schemes shall be selected and used for configuring the meter. 14.3 Reading from the Meter 14.3.1 Reading the meter shall be possible through all the communication means given in clause 14.1.6.

Page 23 of 40

Saudi Electricity Company


SEC DISTRIBUTION MATERIALS SPECIFICATION


40-SDMS-02 REV. 05 DATE: 03 February 2007

14.3.2 This option shall allow the user to read the meter from a preset list of readable features called reading scheme. 14.3.3 The readable features of the meter may be displayed on one or more dialogue boxes through which one can select the required features and store in the reading scheme. One of the many-stored reading schemes shall be selected and used for reading the meter. 14.3.4 The readable features are as given below: (1) (2) (3) (4) All Configuration features given in Table No. 4. All registers listed in clause 11.9.6. All security data listed in clause 11.7.2. The historical data given in clause 11.4

14.3.5 After reading all data it shall be displayed on separate dialogue boxes on the screen. 14.3.6 This option shall allow the user to store all the data in a file with meter number and the date of reading as a reference and later on it may be exported to different data formats for further analysis. 14.4 Reading the Meter for Billing 14.4.1 This option shall be possible through all the communication means given in clause 14.1.6. 14.4.2 This option shall allow the user to read the meter from a preset list of billing features called billing scheme. 14.4.3 The billing features of the meter may be displayed on a dialogue box through which one can select the required features and store in the billing scheme. One of the many-stored billing schemes shall be selected and used for reading the meter for billing purpose. 14.4.4 The readable billing features are as given below: (1) (2) Meter number. All energy registers listed in 11.1.

Page 24 of 40

Saudi Electricity Company


SEC DISTRIBUTION MATERIALS SPECIFICATION


40-SDMS-02 REV. 05 DATE: 03 February 2007

(3) (4)

All tariff registers listed in 11.2 All tariff registers stored in historical data

14.4.5 After reading the billing features it shall be displayed on the screen. 14.4.6 All billing readings taken on a single day shall be appended to one file and stored with user name and the date of reading as a reference and later on it may be exported to the mainframe computer in a different data format for billing purpose. 14.4.7 This option shall cause a reset if the selected reset option is not automatic in Table No. 4. 14.5 Reading the Load Profile Data 14.5.1 This option shall be possible through all the communication means given in clause 14.1.6. 14.5.2 This option shall allow the user to download the load profile data from the meter and store in a file with meter number and the date of reading as the reference. 14.5.3 This option shall have a variety of features to incorporate the acquired load profile data into charts and reports to produce flexible and user defined data analysis. 14.6 Data Export 14.6.1 This option shall allow the user to select the required item from the billing features mentioned in clause 14.4.4 and export the corresponding readings to main frame computer format or one of the data format given in clause 14.6.3. The meter numbers and readings are stored in a file as mentioned in clause 14.4.6 from which the user shall select a group of meters for which the data are to be exported. 14.6.2 This option shall also allow the user to export the load profile data to one of the data format given in clause 14.6.3. This data represents the load profile data of a single meter stored in a file as mentioned in clause 14.5.2.

Page 25 of 40

Saudi Electricity Company


SEC DISTRIBUTION MATERIALS SPECIFICATION


40-SDMS-02 REV. 05 DATE: 03 February 2007

14.6.3 The required export file formats are TXT, EBCDIC, CSV, Microsoft XLS, EDIFACT MSCONS and XML The file extension shall reflect the file format and the export file name shall be given by the user. 14.6.4 Data Export shall be compliant to the standard SAP interface like SAP-ISU CSS and SAP-ISU EDM and must have SAP approval.
15.0 MARKING OF METERS

15.1

Every KWH-Meter shall be provided with a suitable size of name-plate inside the meter cover. Information on this nameplate shall be bilingual (Arabic and English). These shall be printed clearly, indelibly and readable from outside through glass window. Name-plate shall include the following information: (1) (2) (3) (4) (5) (6) The Manufacturer's name or trademark and place of manufacturing. Designation and type. The number of phases and the number of wires for which the meter is designed. The serial number. Year of manufacture. The reference voltage in the form of the nominal voltage of the system or the secondary voltage of the instrument transformer to which the meter is to be connected. (7) (8) (9) (10) (11) (12) (13) The basic current and the rated maximum current; for example: 10 (100) Amps. The reference frequency in Hertz, for example: 60 Hz. The meter constant in the form Imp/kWh and Imp/kvarh. The class index of the meter. The reference temperature if different from 23C. "Property of SEC". SEC Monogram.
Page 26 of 40

15.2

Saudi Electricity Company


SEC DISTRIBUTION MATERIALS SPECIFICATION


40-SDMS-02 REV. 05 DATE: 03 February 2007

(14) (15) 15.3 15.4

SEC purchase order number. SEC item number.

Nameplate shall be included the following information as given in Table No. 5. The meter connections shall be suitable for WC, CT and CT-VT operated metering arrangements as given in Drawing Nos. SEC/KWH-S-02, 03 & 04 respectively. Applicable connection diagram shall be indelibly marked inside the terminal cover of every meter. Table No. 5

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17

Manufacture Type / Model Phases Wires Voltage / Volt / V Amp. / A Imp/KWh or Wh/Imp Frequency / Hz Accuracy Class Temperature C Serial Number Year of Manufacture Purchase Order No. SEC Item No. Property of SEC SEC Monogram Numerals 1 2 3 4 5 6 7 8 9 0

/ :
Page 27 of 40

Saudi Electricity Company


SEC DISTRIBUTION MATERIALS SPECIFICATION


40-SDMS-02 REV. 05 DATE: 03 February 2007

16.0

PACKING

16.1

16.2
17.0

Each meter shall be packed in an individual carton capable of withstanding the rigorous of transportation by Air or Sea or Truck. Other packing / shipping requirements shall be given in SEC General Specification 01-SDMS-01 (latest revision). Materials department shall be contacted for the details of SEC packing requirements.
GUARANTEE

17.1

The Vendor shall guarantee the meters against all defects arising out of faulty design or workmanship or defective material for a period of two years from the date of commissioning or three years from the date of delivery whichever comes first. SEC certificates for date of commissioning shall be accepted. The meters shipped to SEC warehouse shall be subjected to verification test in the SEC laboratory to satisfy all the requirements given in this specification. SEC will carry out the verification test for every meter or on a sample basis. SEC shall specify the method of testing and test reports / certificates shall be acceptable by the manufacturer. 17.3.1 Sample Testing: Testing (acceptance and rejection) shall be as per IEC-62053-21 and IEC1358. 17.3.2 Every KWh-Meter Testing: Every meter that is shipped to SEC warehouse shall be tested. The meters that are failed in accuracy verification test shall be returned to the manufacturer for replacement.

17.2

17.3

17.4

If no exceptions to this specification are taken and no list of deviations is submitted, it shall be deemed that, in every respect, the meters offered shall conform to this specification. SEC interpretation of this Specification shall be accepted.

Page 28 of 40

Saudi Electricity Company


SEC DISTRIBUTION MATERIALS SPECIFICATION


40-SDMS-02 REV. 05 DATE: 03 February 2007

18.0

SUBMITTALS

The following documents shall be submitted by vendor / manufacturer along with the bidding document: 18.1 18.2 18.3 18.4 18.5 18.6 Filled in data sheets. Original/clear copy of catalogues for offered item(s). Copy of type and routine test reports for the offered / identical meter. The type test report shall be obtained from an independent testing agency. Copy of DLMS UA and EURIDIS conformance test certificates for each type of meter. Reference List and experience. Drawing for the following items: (1) (2) (3) (4) (5) (6) 18.7 Sample: 18.7.1 At least one sample meter for each type should be submitted before delivery for final approval. The sample should include a HHU, an optical probe, the software and operational manual for software. 18.7.2 At least one EURIDIS/PLAN modem and one DLMS/COSEM/PLAN PLC type Data Concentrator Unit (DCU) shall be delivered with the sample in order to assure the interoperability with other manufacturers products in an AMR environment for final approval. Connection diagram Overall dimensions Mounting details Sealing arrangement Name-plate Terminal cover

Page 29 of 40

Saudi Electricity Company


SEC DISTRIBUTION MATERIALS SPECIFICATION


40-SDMS-02 REV. 05 DATE: 03 February 2007

19.0

TESTING

19.1

A sample meter of a particular type from a vendor / manufacturer shall be declared acceptable to SEC only if the meter satisfy this specification and the type test in all respects. In case of any conflict the decision of SEC shall be final.
Type Testing

19.2

Type test of the meter shall include but not limited to the following test: (1) Mechanical strength and thermal stability for meter case, cover, window, top and bottom mountings, terminals, terminal block, terminal cover, optical port window, push-buttons and all associated plastic and metallic parts of the meter. Non-flammability of terminal block. Dielectric test. Basic impulse voltage test. Temperature rise test. Power loss in voltage and current circuit. Accuracy test at reference condition and influence quantities as given in this specification and IEC specifications 62053-21 and 62053-23. Meter constant test. Short time over current test. Influence of self-heating. Verification of functional requirement as per this specification. Verification of compatibility of the support systems with other vendor / manufacturer.
19.3 Routine Test

(2) (3) (4) (5) (6) (7) (8) (9) (10) (11) (12)

19.3.1 Routine test shall be performed for each meter that has been delivered to the SEC Central Stores. The manufacturers seal shall be taken as an indication that each meter has been tested and conformed to this specification and respective IEC specifications.

Page 30 of 40

Saudi Electricity Company


SEC DISTRIBUTION MATERIALS SPECIFICATION


40-SDMS-02 REV. 05 DATE: 03 February 2007

19.3.2 Certified and complete routine test report for meters shall be submitted for SEC review / approval prior to shipment. 19.3.3 Routine test of the meter shall include but not limited to the following: (1) (2) (3) (4) (5) (6) (7) Physical checking. Starting. No load (creeping) Insulation (60Hz, 2 KV) Accuracy and calibration on balanced and single phase load. Register test. Verification of meter constant.

Page 31 of 40

Saudi Electricity Company


SEC DISTRIBUTION MATERIALS SPECIFICATION


40-SDMS-02 REV. 05 DATE: 03 February 2007

20.0

TECHNICAL DATA SCHEDULE

ELECTRONIC KILOWATT-HOUR-METER SEC Inquiry No._____________________________ (Sheet 1 of 4)


SEC REF. 3.0 DESCRIPTION APPLICABLE CODES AND STANDARDS
1. Standard to which Manufactured

Item No._________________
VENDOR PROPOSED VALUES

SEC SPECIFIED VALUES

6.0

DESIGN AND CONSTRUCTION


1. 2. 3. 4. 5. 6. Meter case Window material Terminal bore diameter. Terminal cover Overall & mounting dimensions (mm) Top suspension and bottom mountings Nonmetallic Glass / Polycarbonate Short cover Metallic / Hard Plastic Inside meter cover / Under separate cover Terminal block Terminal block Terminal block Terminal block

7. Voltage link for whole current meter 8. Connection for PSTN modem (CT-VT meters) 9. Connection for Euridis port 10. Connection for RS485 11. Connection for Output relay 12. Weight of meter

7.0

ELECTRICAL REQUIREMENTS
1. Nominal / Basic current 2. Over load current (A) Accuracy consideration (Imax) Thermal consideration 3. Reference voltage (V) 4. Measuring element 3 phase 4 wires meters 3 phase 3 wires meters 5. Temp. rise (C) Windings External surface

3 2

Page 32 of 40

Saudi Electricity Company


SEC DISTRIBUTION MATERIALS SPECIFICATION


40-SDMS-02 REV. 05 DATE: 03 February 2007

TECHNICAL DATA SCHEDULE

ELECTRONIC KILOWATT-HOUR-METER SEC Inquiry No._____________________________ (Sheet 2 of 4)


SEC REF. DESCRIPTION
6. Power losses (VA & Watt) 7. Insulation (kV) 8. Short time over current Current coil Voltage coil Power frequency Impulse (1.2 / 50 s) Impulse One millisecond 500 millisecond

Item No._________________
VENDOR PROPOSED VALUES

SEC SPECIFIED VALUES

9. Starting current (%Ib) 10. Creep (+/- % of reference voltage) Active energy measurement 11. Accuracy class Reactive energy measurement 12. Limits of error (%)

IEC-62053-21,23

10.0

INPUT OUTPUT REQUIREMENTS


Same as Drawing No. SEC/KWH-S-05 or equivalent Required IEC 62052 --11 IEC 62052 --11 IEC 62056-21 Required Required

1. LCD Display

Arrangement Max operation temperature

2. Optical Pulse output 3. 4. 5. 6.

Value (Imp / kWh) Value (Imp / kvarh)

Optical interface Display push-button Reset push-button Remote communication interface (CT-VT meters) - PSTN / GSM Modem - Built-in / Plug-in 7. Euridis port 8. RS485 9. Relay Contact rating

Required Required 250V / 1A

Page 33 of 40

Saudi Electricity Company


SEC DISTRIBUTION MATERIALS SPECIFICATION


40-SDMS-02 REV. 05 DATE: 03 February 2007

TECHNICAL DATA SCHEDULE

ELECTRONIC KILOWATT-HOUR-METER SEC Inquiry No._____________________________ (Sheet 3 of 4)


SEC REF. 11.0 DESCRIPTION FUNCTIONAL REQUIREMENTS
1. 2. 3. 4. 5. 6. 7. Energy measurement as per this specification Reverse energy indicator Tariff periods Demand measurement as per this specification Historical recording as per this specification Load profile recording Battery Guaranteed life Whether replaceable Battery fail indicator 8. Super Capacitor Guaranteed life 9. Data retention Type of memory used Guaranteed year of data retention Provision to retrieve data in case of meter failure 10. Instantaneous measurement as per this specification 11. Default settings as per this specification 18.0 Required Required Min. 2 Required Required Required

Item No._________________

SEC SPECIFIED VALUES

VENDOR PROPOSED VALUES

YES / NO Required YES / NO Required

Required Required

SUBMITTALS
Submittals as per this specification YES / NO

Page 34 of 40

Saudi Electricity Company


SEC DISTRIBUTION MATERIALS SPECIFICATION


40-SDMS-02 REV. 05 DATE: 03 February 2007

TECHNICAL DATA SCHEDULE

ELECTRONIC KILOWATT-HOUR-METER SEC Inquiry No._____________________________ (Sheet 4 of 4) Item No._________________

A. ADDITIONAL TECHNICAL INFORMATION OR FEATURES SPECIFIED BY SEC: B. C. ADDITIONAL SUPPLEMENTARY BIDDRE/VENDOR/SUPPLIER: DATA OR FEATURES PROPOSED BY

OTHER PARTICULARS TO BE FILLED UP BY BIDDER/VENDOR/SUPPLIER:

D. LIST OF DEVIATIONS & CLAUSES TO WHICH EXCEPTION IS TAKEN BY THE BIDDER/VENDOR/SUPPLIER:

MANUFACTURER OF MATERIALS/EQUIPMENT Name of Company Location and Office address Name and signature of Authorized Representative and Date Official Seal / Stamp

VENDOR / SUPPLIER

Page 35 of 40

Saudi Electricity Company


SEC DISTRIBUTION MATERIALS SPECIFICATION


40-SDMS-02 REV. 05 DATE: 03 February 2007

270 MAX

6
TERMINAL BLOCK WITH COVER

190 MAX

130 MAX

130 - 170

FRONT VIEW

SIDE VIEW

BACK VIEW

ELECTRONIC KWH METER OVERALL AND MOUNTING DIMENSIONS

DRAWING No. SEC/KWH-S-01

Note: All dimensions are in millimeters with appropriate tolerance.

Page 36 of 40

180 - 230

Saudi Electricity Company


SEC DISTRIBUTION MATERIALS SPECIFICATION


40-SDMS-02 REV. 05 DATE: 03 February 2007

METER BASE

2 METER TERMINAL BLOCK

21 22
9 10 11

31 32

C NO

RS485

Euridis

RELAY TERMINALS R MAIN Y B N SIDE GROOVED VOLTAGE SCREW POWER FLOW R LOAD Y B N

CONNECTION ARRANGEMENT FOR 3 PHASE 4 WIRE WHOLE CURRENT 127/220V & 220/380V ELECTRONIC KWH METER
DRAWING No. SEC/KWH-S-02

Page 37 of 40

Saudi Electricity Company


SEC DISTRIBUTION MATERIALS SPECIFICATION


40-SDMS-02 REV. 05 DATE: 03 February 2007

METER BASE

METER TERMINAL BLOCK

10 11

21 22

31 32
C NO

RS485 S1 S2 P1 R MAIN Y B N POWER FLOW P2 S1 S2 S1 S2 P1 P2

Euridis

RELAY TERMINALS

P1 P2

R Y B N LOAD

CONNECTION ARRANGEMENT FOR 3 PHASE 4 WIRE CT OPERATED 127/220V OR 220/380V ELECTRONIC KWH METER

DRAWING No. SEC/KWH-S-03

Page 38 of 40

Saudi Electricity Company


SEC DISTRIBUTION MATERIALS SPECIFICATION


40-SDMS-02 REV. 05 DATE: 03 February 2007

METER BASE

METER TERMINAL BLOCK

10 11

21 22

31 32

C NO

RS485 u v u U v V S1 S2 P1 P2 S1 S2 P1 P2

ANALOGUE PSTN MODEM

Y B POWER FLOW

Y B

CONNECTION ARRANGEMENT FOR 3 PHASE 3 WIRE CT - VT OPERATED 110V ELECTRONIC KWH METER

DRAWING No. SEC/KWH-S-04

Page 39 of 40

LOAD

MAIN

U V

RELAY TERMINALS R

Saudi Electricity Company


SEC DISTRIBUTION MATERIALS SPECIFICATION


40-SDMS-02 REV. 05 DATE: 03 February 2007

comm

B
kWh

PARAMETER

t.2
8 75

X 100 1 2 3
7

10

1. 2. 3. 4. 5. 6. 7. 8. 9. 10.

Register value / other metering parameter indicator. Communication indicator. Reverse direction indicator. Anomaly indicator. Battery low indicator. Unit of the value/parameter displayed in 1. Phase status indicator. Tariff indicator. DLMS/COSEM/OBIS code/Description of the value/parameter displayed in 1. Multiplication factor.
DISPLAY ARRANGEMENT
DRAWING No. SEC/KWH-S-05

Note: All dimensions are in millimeter. Register digits 6 to 10mm height and all other parameters 3 to 6mm height.

Page 40 of 40

22

00006.5

APPENDIX E: LIGHTING PACKAGE

ITCC in Riyadh Bldg KB04-KB06, IT01-IT03 & RD03-RD04 J09-07800

Divider

Hlderlinstr. 11 D-14050 Berlin - +49.30.3699904.0 www.kardorff.de

ITCC Parcels Design Preliminary Luminaire Catalogue 03.09.2010 03 09 2010

Schematic image

Product image

LUMINAIRE TYPE: T2 INSTALLATION TYPE: Floor mounted INSTALLATION LOCATION: Street pole MANUFACTURER / NAME: Selux/Discera Basys 750/400 PRODUCT NUMBER: 2 x SX 337 22-3 (only heads) LAMP / LIGHTCOLOUR: 1 x HIT-CE 150W / 840 & 1 x HIT-CE 35W / 840 PROTECTION LEVEL: IP 65 COLOUR OF HOUSING: Silver DIMENSIONS [MM]: Width (total) : 3050 Diameter: 750/400 Height: 165/106

Hlderlinstr. Hlderlinstr 11 D-14050 Berlin - +49 30 3699904 0 www kardorff de D 14050 +49.30.3699904.0 www.kardorff.de

PROJECT: ITCC Parcels Design LUMINAIRE: Street pole - HEAD DATE OF ISSUE: 03.09.2010 Reference image Dimensions DRAWN: wf
copyright by Kardorff Ingenieure Document protected by ISO 16016

REVISION / DATE: -

Kardorff Ingenieure Lightingdesign

Waste disposal

Emergency servces

Tourist information

Banner/ advertisements Dimensions

LUMINAIRE TYPE: Pole for Luminaire T2 INSTALLATION TYPE: Floor mounted INSTALLATION LOCATION: Street pole MANUFACTURER / NAME: Selux/ICI PRODUCT NUMBER: ICI O-Shape LAMP / LIGHTCOLOUR: PROTECTION LEVEL: IP 65 COLOUR OF HOUSING: Silver DIMENSIONS [MM]: Diameter: 200 Height: 8130

200 mm

Hlderlinstr. Hlderlinstr 11 D-14050 Berlin - +49 30 3699904 0 www kardorff de D 14050 +49.30.3699904.0 www.kardorff.de

PROJECT: ITCC Parcels Design LUMINAIRE: Street pole - POLE DATE OF ISSUE: 03.09.2010 DRAWN: wf
copyright by Kardorff Ingenieure Document protected by ISO 16016

REVISION / DATE: -

ICI-System for various functions


Kardorff Ingenieure Lightingdesign

Section ICI Pole O-Shape

Schematic light distribution

Product image

LUMINAIRE TYPE: T101 INSTALLATION TYPE: Floor recessed INSTALLATION LOCATION: Landscape / Plazas MANUFACTURER / NAME: WE-EF / ETR139 LED PRODUCT NUMBER: 186-0072 LAMP / LIGHTCOLOUR: 72 x LED 9W (total) / cold white PROTECTION LEVEL: IP 67 COLOUR OF HOUSING: Stainless steel DIMENSIONS [MM]: Width: 160 Length: 565 Height: 80 * max. load 5 tonnes * Optional: RGB

Hlderlinstr. Hlderlinstr 11 D-14050 Berlin - +49 30 3699904 0 www kardorff de D 14050 +49.30.3699904.0 www.kardorff.de

For totally flush luminaire installation: Housing 186-0101

PROJECT: ITCC Parcels Design LUMINAIRE: Light Lines - short DATE OF ISSUE: 03.09.2010 REVISION / DATE: -

Reference image

Dimensions

DRAWN: wf
copyright by Kardorff Ingenieure Document protected by ISO 16016

Kardorff Ingenieure Lightingdesign

Schematic light distribution

Product image

LUMINAIRE TYPE: T102 INSTALLATION TYPE: Floor recessed INSTALLATION LOCATION: Landscape / Plazas MANUFACTURER / NAME: WE-EF / ETR149 LED PRODUCT NUMBER: 186-0124 LAMP / LIGHTCOLOUR: 144 x LED 18W (total) / cold white PROTECTION LEVEL: IP 67 COLOUR OF HOUSING: Stainless steel DIMENSIONS [MM]: Width: 160 Length: 1015 Height: 80 * max. load 5 tonnes * Optional: RGB

Hlderlinstr. Hlderlinstr 11 D-14050 Berlin - +49 30 3699904 0 www kardorff de D 14050 +49.30.3699904.0 www.kardorff.de

For totally flush luminaire installation: Housing 186-0102

PROJECT: ITCC Parcels Design LUMINAIRE: Light Lines - medium DATE OF ISSUE: 03.09.2010 REVISION / DATE: -

Reference image

Dimensions

DRAWN: wf
copyright by Kardorff Ingenieure Document protected by ISO 16016

Kardorff Ingenieure Lightingdesign

Schematic light distribution

Product image

LUMINAIRE TYPE: T103 INSTALLATION TYPE: Floor recessed INSTALLATION LOCATION: Landscape / Plazas MANUFACTURER / NAME: WE-EF / ETR159 LED PRODUCT NUMBER: 186-0082 LAMP / LIGHTCOLOUR: 216 x LED 27W (total) / cold white PROTECTION LEVEL: IP 67 COLOUR OF HOUSING: Stainless steel DIMENSIONS [MM]: Width: 160 Length: 1465 Height: 80 * max. load 5 tonnes * Optional: RGB

Hlderlinstr. Hlderlinstr 11 D-14050 Berlin - +49 30 3699904 0 www kardorff de D 14050 +49.30.3699904.0 www.kardorff.de

For totally flush luminaire installation: Housing 186-0103

PROJECT: ITCC Parcels Design LUMINAIRE: Light Lines - long DATE OF ISSUE: 03.09.2010 REVISION / DATE: -

Reference image

Dimensions

DRAWN: wf
copyright by Kardorff Ingenieure Document protected by ISO 16016

Kardorff Ingenieure Lightingdesign

Schematic light distribution Optional: Concentric ring louver

Product image

LUMINAIRE TYPE: T104 INSTALLATION TYPE: Floor recessed INSTALLATION LOCATION: Landscape (palms/trees) MANUFACTURER / NAME: BEGA PRODUCT NUMBER: 8750 LAMP / LIGHTCOLOUR: HIT-TC-CE 35W / 830 PROTECTION LEVEL: IP 68 COLOUR OF HOUSING: Stainless steel DIMENSIONS [MM]: Diameter: 245 Height: 185 * max. load 2 tonnes

245

For totally flush luminaire installation: Housing 687

Hlderlinstr. Hlderlinstr 11 D-14050 Berlin - +49 30 3699904 0 www kardorff de D 14050 +49.30.3699904.0 www.kardorff.de

PROJECT: ITCC Parcels Design 210 LUMINAIRE: Tree uplight (adjustable) DATE OF ISSUE: 03.09.2010 DRAWN: wf
copyright by Kardorff Ingenieure Document protected by ISO 16016

185

310 Reference image Dimensions

REVISION / DATE: -

Kardorff Ingenieure Lightingdesign

Schematic light distribution Optional: Concentric ring louver

Product image

LUMINAIRE TYPE: T105 INSTALLATION TYPE: Floor recessed INSTALLATION LOCATION: Landscape (palms/trees) MANUFACTURER / NAME: BEGA PRODUCT NUMBER: 8751 LAMP / LIGHTCOLOUR: HIT-TC-CE 70W / 830 PROTECTION LEVEL: IP 68 COLOUR OF HOUSING: Stainless steel DIMENSIONS [MM]: Diameter: 330 Height: 225 * max. load 2 tonnes

330

For totally flush luminaire installation: Housing 688

Hlderlinstr. Hlderlinstr 11 D-14050 Berlin - +49 30 3699904 0 www kardorff de D 14050 +49.30.3699904.0 www.kardorff.de

PROJECT: ITCC Parcels Design 255 LUMINAIRE: Tree uplight (adjustable) DATE OF ISSUE: 03.09.2010 DRAWN: wf
copyright by Kardorff Ingenieure Document protected by ISO 16016

225

395 Reference image Dimensions

REVISION / DATE: -

Kardorff Ingenieure Lightingdesign

Schematic light distribution Optional: Concentric ring louver

Product image

LUMINAIRE TYPE: T106 INSTALLATION TYPE: Floor recessed INSTALLATION LOCATION: Landscape (palms/trees) MANUFACTURER / NAME: BEGA PRODUCT NUMBER: 8753 LAMP / LIGHTCOLOUR: HIT-TC-CE 35W / 830 PROTECTION LEVEL: IP 67 COLOUR OF HOUSING: Stainless steel DIMENSIONS [MM]: Diameter: 245 Height: 230 * max. load 5 tonnes * housing is required

245
Hlderlinstr. Hlderlinstr 11 D-14050 Berlin - +49 30 3699904 0 www kardorff de D 14050 +49.30.3699904.0 www.kardorff.de

PROJECT: ITCC Parcels Design 230 LUMINAIRE: Tree uplight (adjustable) DATE OF ISSUE: 03.09.2010 Reference image Dimensions DRAWN: wf
copyright by Kardorff Ingenieure Document protected by ISO 16016

REVISION / DATE: -

Kardorff Ingenieure Lightingdesign

Schematic light distribution Optional: Concentric ring louver

Product image

LUMINAIRE TYPE: T107 INSTALLATION TYPE: Floor recessed INSTALLATION LOCATION: Landscape (palms/trees) MANUFACTURER / NAME: BEGA PRODUCT NUMBER: 8756 LAMP / LIGHTCOLOUR: HIT-TC-CE 70W / 830 PROTECTION LEVEL: IP 67 COLOUR OF HOUSING: Stainless steel DIMENSIONS [MM]: Diameter: 330 Height: 250 * max. load 5 tonnes * housing is required

330
Hlderlinstr. Hlderlinstr 11 D-14050 Berlin - +49 30 3699904 0 www kardorff de D 14050 +49.30.3699904.0 www.kardorff.de

PROJECT: ITCC Parcels Design 250 LUMINAIRE: Tree uplight (adjustable) DATE OF ISSUE: 03.09.2010 Reference image Dimensions DRAWN: wf
copyright by Kardorff Ingenieure Document protected by ISO 16016

REVISION / DATE: -

Kardorff Ingenieure Lightingdesign

10

Optical accessories: Spread lens 185-2465

Schematic light distribution

Product image

LUMINAIRE TYPE: T108a INSTALLATION TYPE: Floor recessed INSTALLATION LOCATION: Tent shade structure MANUFACTURER / NAME: WE-EF / ETC130-GB PRODUCT NUMBER: 185-2350 LAMP / LIGHTCOLOUR: HIT-CE 35W / 830 PROTECTION LEVEL: IP 67 COLOUR OF HOUSING: Stainless steel DIMENSIONS [MM]: Diameter: 250 Height: 265 * max. load 5 tonnes * housing is required

Hlderlinstr. Hlderlinstr 11 D-14050 Berlin - +49 30 3699904 0 www kardorff de D 14050 +49.30.3699904.0 www.kardorff.de

PROJECT: ITCC Parcels Design LUMINAIRE: Floor recessed uplight DATE OF ISSUE: 03.09.2010 Reference image Dimensions DRAWN: wf
copyright by Kardorff Ingenieure Document protected by ISO 16016

REVISION / DATE: -

Kardorff Ingenieure Lightingdesign

11

Optical accessories: Spread lens 185-2465

Schematic light distribution

Product image

LUMINAIRE TYPE: T108a INSTALLATION TYPE: Floor recessed INSTALLATION LOCATION: Entrance columns (IT-02) MANUFACTURER / NAME: WE-EF / ETC130-GB PRODUCT NUMBER: 185-2350 LAMP / LIGHTCOLOUR: HIT-CE 35W / 830 PROTECTION LEVEL: IP 67 COLOUR OF HOUSING: Stainless steel DIMENSIONS [MM]: Diameter: 250 Height: 265 * max. load 5 tonnes * housing is required

Hlderlinstr. Hlderlinstr 11 D-14050 Berlin - +49 30 3699904 0 www kardorff de D 14050 +49.30.3699904.0 www.kardorff.de

PROJECT: ITCC Parcels Design LUMINAIRE: Floor recessed uplight DATE OF ISSUE: 03.09.2010 Reference image Dimensions DRAWN: wf
copyright by Kardorff Ingenieure Document protected by ISO 16016

REVISION / DATE: -

Kardorff Ingenieure Lightingdesign

12

Optical accessories: Spread lens 185-2467

Schematic light distribution

Product image

LUMINAIRE TYPE: T108b INSTALLATION TYPE: Floor recessed INSTALLATION LOCATION: Tent shade structure MANUFACTURER / NAME: WE-EF / ETC140-GB PRODUCT NUMBER: 185-2400 LAMP / LIGHTCOLOUR: HIT-CE 70W / 830 PROTECTION LEVEL: IP 67 COLOUR OF HOUSING: Stainless steel DIMENSIONS [MM]: Diameter: 300 Height: 315 * max. load 5 tonnes * housing is required

Hlderlinstr. Hlderlinstr 11 D-14050 Berlin - +49 30 3699904 0 www kardorff de D 14050 +49.30.3699904.0 www.kardorff.de

PROJECT: ITCC Parcels Design LUMINAIRE: Floor recessed uplight DATE OF ISSUE: 03.09.2010 Reference image Dimensions DRAWN: wf
copyright by Kardorff Ingenieure Document protected by ISO 16016

REVISION / DATE: -

Kardorff Ingenieure Lightingdesign

13

Schematic light distribution

Product image

LUMINAIRE TYPE: T109 INSTALLATION TYPE: Floor mounted INSTALLATION LOCATION: Fountains MANUFACTURER / NAME: ACDC / Polo PRODUCT NUMBER: LAMP / LIGHTCOLOUR: 9 x LED 3W / cold white PROTECTION LEVEL: IP 68 COLOUR OF HOUSING: Anodised Aluminum silver DIMENSIONS [MM]: Diameter: 192 Cutout: 48 Height: 60 * To use with external LED transformer * Optional: RGB

Hlderlinstr. Hlderlinstr 11 D-14050 Berlin - +49 30 3699904 0 www kardorff de D 14050 +49.30.3699904.0 www.kardorff.de

PROJECT: ITCC Parcels Design LUMINAIRE: Fountain Uplight DATE OF ISSUE: 03.09.2010 Reference image Dimensions DRAWN: wf
copyright by Kardorff Ingenieure Document protected by ISO 16016

REVISION / DATE: -

Kardorff Ingenieure Lightingdesign

14

Schematic light distribution

Product image

LUMINAIRE TYPE: T110 INSTALLATION TYPE: Floor mounted INSTALLATION LOCATION: Fountains MANUFACTURER / NAME: Wibre PRODUCT NUMBER: 4.0192.90.xx LAMP / LIGHTCOLOUR: 12 x LED 1W / cold white PROTECTION LEVEL: IP 68 COLOUR OF HOUSING: Stainless steel DIMENSIONS [MM]: Diameter: 170 Width: 80 Height: 212 * To use with external LED transformer * Optional: RGB

Hlderlinstr. Hlderlinstr 11 D-14050 Berlin - +49 30 3699904 0 www kardorff de D 14050 +49.30.3699904.0 www.kardorff.de

PROJECT: ITCC Parcels Design LUMINAIRE: Fountain Spot (adjustable) DATE OF ISSUE: 03.09.2010 Reference image Dimensions DRAWN: wf
copyright by Kardorff Ingenieure Document protected by ISO 16016

REVISION / DATE: -

Kardorff Ingenieure Lightingdesign

15

Schematic light distribution

Product image

Installation Housing

LUMINAIRE TYPE: T111 INSTALLATION TYPE: Wall recessed INSTALLATION LOCATION: Fountains MANUFACTURER / NAME: Wibre PRODUCT NUMBER: 4.0083.00.xx LAMP / LIGHTCOLOUR: 3 x LED 3W / cold white PROTECTION LEVEL: IP 68 COLOUR OF HOUSING: Stainless steel DIMENSIONS [MM]: Diameter: 84 Height: 158 * To use with external LED transformer * housing is required * Optional: RGB

Hlderlinstr. Hlderlinstr 11 D-14050 Berlin - +49 30 3699904 0 www kardorff de D 14050 +49.30.3699904.0 www.kardorff.de

PROJECT: ITCC Parcels Design LUMINAIRE: Fountain Spot DATE OF ISSUE: 03.09.2010 Reference image Dimensions DRAWN: wf
copyright by Kardorff Ingenieure Document protected by ISO 16016

REVISION / DATE: -

Kardorff Ingenieure Lightingdesign

16

Schematic light distribution

Product image
16

LUMINAIRE TYPE: T112a INSTALLATION TYPE: Wall recessed / surface mounted INSTALLATION LOCATION: Benches MANUFACTURER / NAME: LED-Linear / VarioLED Flex Venus PRODUCT NUMBER: 1111x-01 LAMP / LIGHTCOLOUR: LED / 2900K, 350lm/m PROTECTION LEVEL: IP 67 COLOUR OF HOUSING: DIMENSIONS [MM]: Width: 16 Lengths available: 269, 519, 1019, 2019 Height: 14.5 * To use with external LED transformer

varies
Hlderlinstr. Hlderlinstr 11 D-14050 Berlin - +49 30 3699904 0 www kardorff de D 14050 +49.30.3699904.0 www.kardorff.de

PROJECT: ITCC Parcels Design


14.5

LUMINAIRE: Linear light DATE OF ISSUE: 03.09.2010 DRAWN: wf


copyright by Kardorff Ingenieure Document protected by ISO 16016

varies

REVISION / DATE: -

Reference image

Dimensions

Kardorff Ingenieure Lightingdesign

17

Schematic light distribution

Product image
16

LUMINAIRE TYPE: T112b INSTALLATION TYPE: Wall recessed / surface mounted INSTALLATION LOCATION: Faade lighting (IT-01) MANUFACTURER / NAME: LED-Linear / VarioLED Flex Venus PRODUCT NUMBER: 1111x-01 LAMP / LIGHTCOLOUR: LED / 4100K, 350lm/m PROTECTION LEVEL: IP 67 COLOUR OF HOUSING: DIMENSIONS [MM]: Width: 16 Lengths available: 269, 519, 1019, 2019 Height: 14.5 * To use with external LED transformer

varies
Hlderlinstr. Hlderlinstr 11 D-14050 Berlin - +49 30 3699904 0 www kardorff de D 14050 +49.30.3699904.0 www.kardorff.de

PROJECT: ITCC Parcels Design


14.5

LUMINAIRE: Linear light DATE OF ISSUE: 03.09.2010 DRAWN: wf


copyright by Kardorff Ingenieure Document protected by ISO 16016

varies

REVISION / DATE: -

Reference image

Dimensions

Kardorff Ingenieure Lightingdesign

18

Schematic light distribution

Product image

LUMINAIRE TYPE: T113 INSTALLATION TYPE: Floor mounted INSTALLATION LOCATION: Driveway / Landscape areas MANUFACTURER / NAME: Santa Cole / Finisterra PRODUCT NUMBER: LAMP / LIGHTCOLOUR: 240 LED x 0.1W / red and green PROTECTION LEVEL: IP 55 COLOUR OF HOUSING: Black DIMENSIONS [MM]: Width: 310 Height: 810

310

Hlderlinstr. Hlderlinstr 11 D-14050 Berlin - +49 30 3699904 0 www kardorff de D 14050 +49.30.3699904.0 www.kardorff.de

810

PROJECT: ITCC Parcels Design LUMINAIRE: Protective Bollard

330

DATE OF ISSUE: 03.09.2010


110

REVISION / DATE: -

Reference image

Dimensions

DRAWN: wf
copyright by Kardorff Ingenieure Document protected by ISO 16016

Kardorff Ingenieure Lightingdesign

19

Schematic light distribution

Product image

LUMINAIRE TYPE: T114 INSTALLATION TYPE: Wall mounted INSTALLATION LOCATION: Central Canopy MANUFACTURER / NAME: Meyer / Nightvision Mini PRODUCT NUMBER: 8 705 056 000 LAMP / LIGHTCOLOUR: HIT-CE 35W / 830 PROTECTION LEVEL: IP 65 COLOUR OF HOUSING: Silver Gray DIMENSIONS [MM]: Length: 331 Height: 78 Width:147

Hlderlinstr. Hlderlinstr 11 D-14050 Berlin - +49 30 3699904 0 www kardorff de D 14050 +49.30.3699904.0 www.kardorff.de

PROJECT: ITCC Parcels Design LUMINAIRE: Adjustable uplight DATE OF ISSUE: 03.09.2010 Reference image Dimensions DRAWN: wf
copyright by Kardorff Ingenieure Document protected by ISO 16016

REVISION / DATE: -

Kardorff Ingenieure Lightingdesign

20

Schematic light distribution

Product image

LUMINAIRE TYPE: T115 INSTALLATION TYPE: Floor recessed INSTALLATION LOCATION: Entrance Canopy (KB04) MANUFACTURER / NAME: WE-EF / ETC 140 PRODUCT NUMBER: 185-1577 LAMP / LIGHTCOLOUR: HIT-CE 70W / 830 PROTECTION LEVEL: IP 67 COLOUR OF HOUSING: DIMENSIONS [MM]: Diameter: 300 Height: 315 * accessories: Concentric louvres, directional lens, cool touch adaptor * housing is required

Hlderlinstr. Hlderlinstr 11 D-14050 Berlin - +49 30 3699904 0 www kardorff de D 14050 +49.30.3699904.0 www.kardorff.de

PROJECT: ITCC Parcels Design LUMINAIRE: Floor recessed uplight DATE OF ISSUE: 03.09.2010 Reference image Dimensions i i DRAWN: wf
copyright by Kardorff Ingenieure Document protected by ISO 16016

REVISION / DATE: -

Kardorff Ingenieure Lightingdesign

21

Schematic light distribution

Product image

LUMINAIRE TYPE: T115 INSTALLATION TYPE: Floor recessed INSTALLATION LOCATION: Wrapped Roof Structure (WH-06) MANUFACTURER / NAME: WE-EF / ETC 140 PRODUCT NUMBER: 185-1577 LAMP / LIGHTCOLOUR: HIT-CE 70W / 830 PROTECTION LEVEL: IP 67 COLOUR OF HOUSING: DIMENSIONS [MM]: Diameter: 300 Height: 315 * accessories: Concentric louvres, directional lens, Cool touch adaptor * housing is required

Hlderlinstr. Hlderlinstr 11 D-14050 Berlin - +49 30 3699904 0 www kardorff de D 14050 +49.30.3699904.0 www.kardorff.de

PROJECT: ITCC Parcels Design LUMINAIRE: Floor recessed uplight DATE OF ISSUE: 03.09.2010 Reference image Dimensions i i DRAWN: wf
copyright by Kardorff Ingenieure Document protected by ISO 16016

REVISION / DATE: -

Kardorff Ingenieure Lightingdesign

22

Schematic light distribution

Product image

LUMINAIRE TYPE: T115 INSTALLATION TYPE: Floor recessed INSTALLATION LOCATION: Entrance columns (IT-01) MANUFACTURER / NAME: WE-EF / ETC 140 PRODUCT NUMBER: 185-1577 LAMP / LIGHTCOLOUR: HIT-CE 70W / 830 PROTECTION LEVEL: IP 67 COLOUR OF HOUSING: DIMENSIONS [MM]: Diameter: 300 Height: 315 * accessories: Concentric louvres, directional lens, Cool touch adaptor * housing is required

Hlderlinstr. Hlderlinstr 11 D-14050 Berlin - +49 30 3699904 0 www kardorff de D 14050 +49.30.3699904.0 www.kardorff.de

PROJECT: ITCC Parcels Design LUMINAIRE: Floor recessed uplight DATE OF ISSUE: 03.09.2010 Reference image Dimensions i i DRAWN: wf
copyright by Kardorff Ingenieure Document protected by ISO 16016

REVISION / DATE: -

Kardorff Ingenieure Lightingdesign

23

Schematic light distribution

Product image

LUMINAIRE TYPE: T115 INSTALLATION TYPE: Floor recessed INSTALLATION LOCATION: Entrance wall (WH-06 KB-03) (WH-06, MANUFACTURER / NAME: WE-EF / ETC 140 PRODUCT NUMBER: 185-1577 LAMP / LIGHTCOLOUR: HIT-CE 70W / 830 PROTECTION LEVEL: IP 67 COLOUR OF HOUSING: DIMENSIONS [MM]: Diameter: 300 Height: 315 * accessories: Concentric louvres, directional lens, Cool touch adaptor * housing is required

Hlderlinstr. Hlderlinstr 11 D-14050 Berlin - +49 30 3699904 0 www kardorff de D 14050 +49.30.3699904.0 www.kardorff.de

PROJECT: ITCC Parcels Design LUMINAIRE: Floor recessed uplight DATE OF ISSUE: 03.09.2010 Reference image Dimensions i i DRAWN: wf
copyright by Kardorff Ingenieure Document protected by ISO 16016

REVISION / DATE: -

Kardorff Ingenieure Lightingdesign

24

Schematic light distribution

Product image

LUMINAIRE TYPE: T116a INSTALLATION TYPE: Floor mounted INSTALLATION LOCATION: External faade Wall (KB-04) MANUFACTURER / NAME: ERCO / Focalflood PRODUCT NUMBER: 34103 LAMP / LIGHTCOLOUR: HIT-CE 35W / 830 PROTECTION LEVEL: IP 65 COLOUR OF HOUSING: Silver Grey DIMENSIONS [MM]: Length: 245 Height: 312 Width: 207

Hlderlinstr. Hlderlinstr 11 D-14050 Berlin - +49 30 3699904 0 www kardorff de D 14050 +49.30.3699904.0 www.kardorff.de

PROJECT: ITCC Parcels Design LUMINAIRE: Flood light - External faade DATE OF ISSUE: 03.09.2010 Reference image Dimensions i i DRAWN: wf
copyright by Kardorff Ingenieure Document protected by ISO 16016

REVISION / DATE: -

Kardorff Ingenieure Lightingdesign

25

Schematic light distribution

Product image

LUMINAIRE TYPE: T116b INSTALLATION TYPE: Floor mounted INSTALLATION LOCATION: External faade Wall (KB-03 KB-04) (KB-03, MANUFACTURER / NAME: ERCO / Focalflood PRODUCT NUMBER: 34105 LAMP / LIGHTCOLOUR: HIT-CE 70W / 830 PROTECTION LEVEL: IP 65 COLOUR OF HOUSING: Silver Grey DIMENSIONS [MM]: Length: 245 Height: 312 Width: 207

Hlderlinstr. Hlderlinstr 11 D-14050 Berlin - +49 30 3699904 0 www kardorff de D 14050 +49.30.3699904.0 www.kardorff.de

PROJECT: ITCC Parcels Design LUMINAIRE: Flood light - External faade DATE OF ISSUE: 03.09.2010 Reference image Dimensions i i DRAWN: wf
copyright by Kardorff Ingenieure Document protected by ISO 16016

REVISION / DATE: -

Kardorff Ingenieure Lightingdesign

26

Schematic light distribution

Schematic sketch horizontal section through the walls Option A: Wall recessed Product image

LUMINAIRE TYPE: T117 INSTALLATION TYPE: Surface mounted / Recessed INSTALLATION LOCATION: Curved wall gaps (KB-04) MANUFACTURER / NAME: Linear LED / VarioLED HighFlux PRODUCT NUMBER: LAMP / LIGHTCOLOUR: LED 24V, 60, 3500K, 700 lumens/m PROTECTION LEVEL: IP 67 COLOUR OF HOUSING: Aluminum DIMENSIONS [MM]: Length: 410 (module) Height: 9 Width:18,7 * To use with external LED transformer

Option B: Wall mounted

Hlderlinstr. Hlderlinstr 11 D-14050 Berlin - +49 30 3699904 0 www kardorff de D 14050 +49.30.3699904.0 www.kardorff.de

PROJECT: ITCC Parcels Design LUMINAIRE: Linear Light for Curved Wall - internal face DATE OF ISSUE: 03.09.2010 Reference image Dimensions DRAWN: wf
copyright by Kardorff Ingenieure Document protected by ISO 16016

REVISION / DATE: -

Kardorff Ingenieure Lightingdesign

27

Schematic light distribution

Schematic sketch Vertical section through the canopy / pergola beams Option A: Recessed Product image

LUMINAIRE TYPE: T117 INSTALLATION TYPE: Surface mounted / Recessed INSTALLATION LOCATION: Canopy / Pergola-internal face (KB-03) MANUFACTURER / NAME: Linear LED / VarioLED HighFlux PRODUCT NUMBER: LAMP / LIGHTCOLOUR: LED 24V, 60, 3500K, 700 lumens/m PROTECTION LEVEL: IP 67 COLOUR OF HOUSING: Aluminum DIMENSIONS [MM]: Length: 410 (module) Height: 9 Width:18,7 * To use with external LED transformer

Option B: Surface mounted

Hlderlinstr. Hlderlinstr 11 D-14050 Berlin - +49 30 3699904 0 www kardorff de D 14050 +49.30.3699904.0 www.kardorff.de

PROJECT: ITCC Parcels Design LUMINAIRE: Linear Light for Canopy / Pergola - internal face DATE OF ISSUE: REVISION / DATE: 03.09.2010 Reference image Dimensions DRAWN: wf
copyright by Kardorff Ingenieure Document protected by ISO 16016

Kardorff Ingenieure Lightingdesign

28

Schematic light distribution

Product image

LUMINAIRE TYPE: T117 INSTALLATION TYPE: Surface mounted INSTALLATION LOCATION: Metal screen panels (KB-03) MANUFACTURER / NAME: Linear LED / VarioLED HighFlux PRODUCT NUMBER: LAMP / LIGHTCOLOUR: LED 24V, 60, 3500K, 700 lumens/m PROTECTION LEVEL: IP 67 COLOUR OF HOUSING: Aluminum DIMENSIONS [MM]: Length: 410 (module) Height: 9 Width:18.7 * To use with external LED transformer

Partial Section through the roof: LED profiles embedded in the metal screen panels Partial Vertical Section: LED profiles embedded in the metal screen p panels

Hlderlinstr. Hlderlinstr 11 D-14050 Berlin - +49 30 3699904 0 www kardorff de D 14050 +49.30.3699904.0 www.kardorff.de

PROJECT: ITCC Parcels Design LUMINAIRE: Linear Light for Metal Screen panels (Elevation B & C, Roof over inner courtyard) DATE OF ISSUE: REVISION / DATE: 03.09.2010 Reference image Dimensions DRAWN: wf
copyright by Kardorff Ingenieure Document protected by ISO 16016

Kardorff Ingenieure Lightingdesign

29

Schematic light distribution

Product image

LUMINAIRE TYPE: T118 INSTALLATION TYPE: Floor mounted INSTALLATION LOCATION: Landscape areas MANUFACTURER / NAME: Schrder/Modullum Midi PRODUCT NUMBER: LAMP / LIGHTCOLOUR: 3 x HIT-CE 70W / 840 PROTECTION LEVEL: IP 65 COLOUR OF HOUSING: Graphite DIMENSIONS [MM]: Height (one module): 460mm Height (total): 5400 Diameter: 178

Hlderlinstr. Hlderlinstr 11 D-14050 Berlin - +49 30 3699904 0 www kardorff de D 14050 +49.30.3699904.0 www.kardorff.de

PROJECT: ITCC Parcels Design LUMINAIRE: Pole luminaire General Lighting DATE OF ISSUE: 03.09.2010 Reference image Dimensions DRAWN: wf
copyright by Kardorff Ingenieure Document protected by ISO 16016

REVISION / DATE: -

Kardorff Ingenieure Lightingdesign

30

Schematic light distribution

Product image

LUMINAIRE TYPE: T119 INSTALLATION TYPE: Wall mounted INSTALLATION LOCATION: Central Courtyard MANUFACTURER / NAME: Sill PRODUCT NUMBER: 903-459 6 025 33 LAMP / LIGHTCOLOUR: HIT-DE 250W / 830 PROTECTION LEVEL: IP 55 COLOUR OF HOUSING: Aluminum DIMENSIONS [MM]: Length: 379 Width: 660 Height: 189

Hlderlinstr. Hlderlinstr 11 D-14050 Berlin - +49 30 3699904 0 www kardorff de D 14050 +49.30.3699904.0 www.kardorff.de

PROJECT: ITCC Parcels Design LUMINAIRE: Ceiling Washer Flood light DATE OF ISSUE: 03.09.2010 Dimensions DRAWN: wf
copyright by Kardorff Ingenieure Document protected by ISO 16016

REVISION / DATE: -

Kardorff Ingenieure Lightingdesign

31

Schematic light distribution

Product image

LUMINAIRE TYPE: T120a INSTALLATION TYPE: Floor recessed INSTALLATION LOCATION: External faade (KB05-06) MANUFACTURER / NAME: WE-EF/ ETR140 (A20) PRODUCT NUMBER: 186-0098 LAMP / LIGHTCOLOUR: T16 39W / 827 PROTECTION LEVEL: IP 67 COLOUR OF HOUSING: Aluminum DIMENSIONS [MM]: Length: 1015 Width: 160 Height: 80 * max. load 5 tonnes

Hlderlinstr. Hlderlinstr 11 D-14050 Berlin - +49 30 3699904 0 www kardorff de D 14050 +49.30.3699904.0 www.kardorff.de

For flush luminaire installation: Housing 186-0102

PROJECT: ITCC Parcels Design LUMINAIRE: Floor recessed linear wall washer DATE OF ISSUE: 03.09.2010 REVISION / DATE: -

Reference image

Dimensions

DRAWN: wf
copyright by Kardorff Ingenieure Document protected by ISO 16016

Kardorff Ingenieure Lightingdesign

32

Schematic light distribution

Product image

LUMINAIRE TYPE: T120b INSTALLATION TYPE: Floor recessed INSTALLATION LOCATION: Massive faade (IT-01) MANUFACTURER / NAME: WE-EF/ ETR140 (A20) PRODUCT NUMBER: 186-0098 LAMP / LIGHTCOLOUR: T16 39W / 840 PROTECTION LEVEL: IP 67 COLOUR OF HOUSING: Aluminum DIMENSIONS [MM]: Length: 1015 Width: 160 Height: 80 * max. load 5 tonnes

Hlderlinstr. Hlderlinstr 11 D-14050 Berlin - +49 30 3699904 0 www kardorff de D 14050 +49.30.3699904.0 www.kardorff.de

For flush luminaire installation: Housing 186-0102

PROJECT: ITCC Parcels Design LUMINAIRE: Floor recessed linear wall washer DATE OF ISSUE: 03.09.2010 REVISION / DATE: -

Reference image

Dimensions

DRAWN: wf
copyright by Kardorff Ingenieure Document protected by ISO 16016

Kardorff Ingenieure Lightingdesign

33

Schematic light distribution

Product image

LUMINAIRE TYPE: T121 INSTALLATION TYPE: Floor recessed INSTALLATION LOCATION: External faade MANUFACTURER / NAME: WE-EF/ ETC150 (A) PRODUCT NUMBER: 185-1608 LAMP / LIGHTCOLOUR: HIT-CE 150W / 830 PROTECTION LEVEL: IP 67 COLOUR OF HOUSING: Stainless steel DIMENSIONS [MM]: Diameter: 355 Height: 330 * max. load 5 tonnes

For flush luminaire installation: Housing 185-1622


355
Hlderlinstr. Hlderlinstr 11 D-14050 Berlin - +49 30 3699904 0 www kardorff de D 14050 +49.30.3699904.0 www.kardorff.de

435

PROJECT: ITCC Parcels Design LUMINAIRE: Floor recessed asymmetric uplight

385

DATE OF ISSUE: 03.09.2010 DRAWN: wf

REVISION / DATE: -

Reference image

Dimensions

Kardorff Ingenieure Lightingdesign

copyright by Kardorff Ingenieure Document protected by ISO 16016

34

Schematic light distribution

Product image

LUMINAIRE TYPE: T122 INSTALLATION TYPE: Floor mounted INSTALLATION LOCATION: Landscape areas MANUFACTURER / NAME: iGuzzini / Miniwoody PRODUCT NUMBER: B583 (Flood) LAMP / LIGHTCOLOUR: HIT-CE 20W / 830 PROTECTION LEVEL: IP 66 COLOUR OF HOUSING: Graphite DIMENSIONS [MM]: Length: 125 Width: 125 Height: 205

Hlderlinstr. Hlderlinstr 11 D-14050 Berlin - +49 30 3699904 0 www kardorff de D 14050 +49.30.3699904.0 www.kardorff.de

PROJECT: ITCC Parcels Design LUMINAIRE: Adjustable accent Plant Lighting DATE OF ISSUE: 03.09.2010 Reference image Dimensions DRAWN: wf
copyright by Kardorff Ingenieure Document protected by ISO 16016

REVISION / DATE: -

Kardorff Ingenieure Lightingdesign

35

Schematic light distribution

Product image

LUMINAIRE TYPE: T123a INSTALLATION TYPE: Wall mounted INSTALLATION LOCATION: Entrance MANUFACTURER / NAME: Sill PRODUCT NUMBER: 903-459 6 007 36 LAMP / LIGHTCOLOUR: HIT-CE 70W / 830 PROTECTION LEVEL: IP 55 COLOUR OF HOUSING: Aluminum DIMENSIONS [MM]: Length: 379 Width: 660 Height: 189 * Control gear required

Hlderlinstr. Hlderlinstr 11 D-14050 Berlin - +49 30 3699904 0 www kardorff de D 14050 +49.30.3699904.0 www.kardorff.de

PROJECT: ITCC Parcels Design LUMINAIRE: Ceiling Washer Flood light DATE OF ISSUE: 03.09.2010 Reference image g Dimensions DRAWN: wf
copyright by Kardorff Ingenieure Document protected by ISO 16016

REVISION / DATE: -

Kardorff Ingenieure Lightingdesign

36

Schematic light distribution

Product image

LUMINAIRE TYPE: T123b INSTALLATION TYPE: Wall mounted INSTALLATION LOCATION: Entrance MANUFACTURER / NAME: Sill PRODUCT NUMBER: 903-459 6 015 35 LAMP / LIGHTCOLOUR: HIT-DE 150W / 830 PROTECTION LEVEL: IP 55 COLOUR OF HOUSING: Aluminum DIMENSIONS [MM]: Length: 379 Width: 660 Height: 189 * Control gear required

Hlderlinstr. Hlderlinstr 11 D-14050 Berlin - +49 30 3699904 0 www kardorff de D 14050 +49.30.3699904.0 www.kardorff.de

PROJECT: ITCC Parcels Design LUMINAIRE: Ceiling Washer Flood light DATE OF ISSUE: 03.09.2010 Reference image g Dimensions DRAWN: wf
copyright by Kardorff Ingenieure Document protected by ISO 16016

REVISION / DATE: -

Kardorff Ingenieure Lightingdesign

37

Schematic light distribution

Product image

LUMINAIRE TYPE: T124 INSTALLATION TYPE: Ceiling recessed INSTALLATION LOCATION: Entrance (IT-02 WH-05) (IT-02, MANUFACTURER / NAME: BEGA PRODUCT NUMBER: 6902 + 443 (housing) LAMP / LIGHTCOLOUR: HIT-CE 35W / 840 PROTECTION LEVEL: IP 65 COLOUR OF HOUSING: Aluminum DIMENSIONS [MM]: Diameter: 240 Height: 230 * Equipped with electronic control gear

202

Hlderlinstr. Hlderlinstr 11 D-14050 Berlin - +49 30 3699904 0 www kardorff de D 14050 +49.30.3699904.0 www.kardorff.de

230

250

PROJECT: ITCC Parcels Design LUMINAIRE: Ceiling recessed downlight DATE OF ISSUE: 03.09.2010 DRAWN: wf
copyright by Kardorff Ingenieure Document protected by ISO 16016

202 240 320 Housing

REVISION / DATE: -

Reference image

Dimensions

Kardorff Ingenieure Lightingdesign

38

Schematic light distribution

Product image

LUMINAIRE TYPE: T125 INSTALLATION TYPE: Surface mounted INSTALLATION LOCATION: Faade construction MANUFACTURER / NAME: LEC/Mplec PRODUCT NUMBER: 1822 LAMP / LIGHTCOLOUR: LED / neutral white PROTECTION LEVEL: IP 67 COLOUR OF HOUSING: DIMENSIONS [MM]: Width: 84 Height: 45 * To use with external LED transformer

Hlderlinstr. Hlderlinstr 11 D-14050 Berlin - +49 30 3699904 0 www kardorff de D 14050 +49.30.3699904.0 www.kardorff.de

PROJECT: ITCC Parcels Design LUMINAIRE: Light dot DATE OF ISSUE: 03.09.2010 Reference image Light dots Dimensions DRAWN: wf
copyright by Kardorff Ingenieure Document protected by ISO 16016

REVISION / DATE: -

Kardorff Ingenieure Lightingdesign

39

Schematic light distribution

Product image

LUMINAIRE TYPE: T126 INSTALLATION TYPE: Floor recessed INSTALLATION LOCATION: Landscape areas MANUFACTURER / NAME: Wever & Ducr / DRUM PRODUCT NUMBER: 800057 LAMP / LIGHTCOLOUR: LED 8W / RGB PROTECTION LEVEL: IP 67 COLOUR OF HOUSING: DIMENSIONS [MM]: Width: 200 Length: 200 Height: 95 * max. load 600 kg * To use with external LED transformer

For totally flush luminaire installation: Housing 1800044

Hlderlinstr. Hlderlinstr 11 D-14050 Berlin - +49 30 3699904 0 www kardorff de D 14050 +49.30.3699904.0 www.kardorff.de

PROJECT: ITCC Parcels Design LUMINAIRE: Orientation Light DATE OF ISSUE: 03.09.2010 Reference image Dimensions DRAWN: wf
copyright by Kardorff Ingenieure Document protected by ISO 16016

REVISION / DATE: -

Kardorff Ingenieure Lightingdesign

40

Schematic light distribution

Product image

LUMINAIRE TYPE: T127 INSTALLATION TYPE: Floor mounted INSTALLATION LOCATION: Landscape areas MANUFACTURER / NAME: Lichtwerk / Light qube PRODUCT NUMBER: LAMP / LIGHTCOLOUR: Fluorescent or LED / cold white PROTECTION LEVEL: IP 65 COLOUR OF HOUSING: white DIMENSIONS [MM]: Width: 500 Length: 500 Height: 500 * Optional: RGB

Hlderlinstr. Hlderlinstr 11 D-14050 Berlin - +49 30 3699904 0 www kardorff de D 14050 +49.30.3699904.0 www.kardorff.de

PROJECT: ITCC Parcels Design


500

LUMINAIRE: Light Cubes DATE OF ISSUE: 03.09.2010 DRAWN: wf


copyright by Kardorff Ingenieure Document protected by ISO 16016

500

REVISION / DATE: -

Reference image

Dimensions

Kardorff Ingenieure Lightingdesign

41

Schematic light distribution

Dimensions

LUMINAIRE TYPE: T128 INSTALLATION TYPE: Recessed / surface mounted INSTALLATION LOCATION: Shading structure MANUFACTURER / NAME: GE-Lighting / Tetra Contour PRODUCT NUMBER: GWHXNLE1 LAMP / LIGHTCOLOUR: LED 3,39W/m, 24V, 6500K, 341 lumens/m PROTECTION LEVEL: IP 66 COLOUR OF HOUSING: DIMENSIONS [MM]: Length: up to 2438 (module) Height: 25 Width: 18 * To use with external LED transformer

Hlderlinstr. Hlderlinstr 11 D-14050 Berlin - +49 30 3699904 0 www kardorff de D 14050 +49.30.3699904.0 www.kardorff.de

PROJECT: ITCC Parcels Design LUMINAIRE: Linear light Shading structure DATE OF ISSUE: 03.09.2010 Reference image Product image DRAWN: wf
copyright by Kardorff Ingenieure Document protected by ISO 16016

REVISION / DATE: -

Kardorff Ingenieure Lightingdesign

42

Screen construction Wall washer up Dome Schematic light distribution

Product image

Wall washer down Metal mesh l h Schematic sketch

LUMINAIRE TYPE: T129 INSTALLATION TYPE: faade mounted INSTALLATION LOCATION: Metal screen construction MANUFACTURER / NAME: Meyer / Nightvision + Filter Blue PRODUCT NUMBER: 8 744 044 000 LAMP / LIGHTCOLOUR: HIT-DE-CE 150W / 840 PROTECTION LEVEL: IP 65 COLOUR OF HOUSING: Black DIMENSIONS [MM]: Width: 282 Length: 420 Height: 84

Hlderlinstr. Hlderlinstr 11 D-14050 Berlin - +49 30 3699904 0 www kardorff de D 14050 +49.30.3699904.0 www.kardorff.de

PROJECT: ITCC Parcels Design LUMINAIRE: Adjustable flood light - Dome DATE OF ISSUE: 03.09.2010 Reference image Dimensions DRAWN: wf
copyright by Kardorff Ingenieure Document protected by ISO 16016

REVISION / DATE: -

Kardorff Ingenieure Lightingdesign

43

Schematic light distribution

Possible control gear Product image

LUMINAIRE TYPE: T130 INSTALLATION TYPE: Surface mounted INSTALLATION LOCATION: Canopy roofs underside (WH01-04) roof s MANUFACTURER / NAME: ACDC / Contour Exterior PRODUCT NUMBER: LAMP / LIGHTCOLOUR: Cold Cathode / 3000 K PROTECTION LEVEL: IP 65 COLOUR OF HOUSING: DIMENSIONS [MM]: Width: 24 Length: varies Height: 50 * To use with remote control gear

Hlderlinstr. Hlderlinstr 11 D-14050 Berlin - +49 30 3699904 0 www kardorff de D 14050 +49.30.3699904.0 www.kardorff.de

PROJECT: ITCC Parcels Design LUMINAIRE: Light Line Canopy Roof DATE OF ISSUE: 03.09.2010 Reference image Dimensions DRAWN: wf
copyright by Kardorff Ingenieure Document protected by ISO 16016

REVISION / DATE: -

Kardorff Ingenieure Lightingdesign

44

Schematic light distribution

Possible control gear Product image

LUMINAIRE TYPE: T130 INSTALLATION TYPE: Surface mounted INSTALLATION LOCATION: Wrapped Roof Contours (WH-06) MANUFACTURER / NAME: ACDC / Contour Exterior PRODUCT NUMBER: LAMP / LIGHTCOLOUR: Cold Cathode / 3000 K PROTECTION LEVEL: IP 65 COLOUR OF HOUSING: DIMENSIONS [MM]: Width: 24 Length: as per design Height: 50 * To use with remote control gear

Hlderlinstr. Hlderlinstr 11 D-14050 Berlin - +49 30 3699904 0 www kardorff de D 14050 +49.30.3699904.0 www.kardorff.de

PROJECT: ITCC Parcels Design LUMINAIRE: Cold Cathode / Wrapped Roof Contours DATE OF ISSUE: 03.09.2010 Reference image Dimensions DRAWN: wf
copyright by Kardorff Ingenieure Document protected by ISO 16016

REVISION / DATE: -

Kardorff Ingenieure Lightingdesign

45

Schematic light distribution

Possible control gear Product image

LUMINAIRE TYPE: T130 INSTALLATION TYPE: Surface mounted INSTALLATION LOCATION: Highlighted text (KB01-02) MANUFACTURER / NAME: ACDC / Contour Exterior PRODUCT NUMBER: LAMP / LIGHTCOLOUR: Cold Cathode / 3000 K PROTECTION LEVEL: IP 65 COLOUR OF HOUSING: DIMENSIONS [MM]: Width: 24 Length: as per design Height: 50 * To use with remote control gear

Hlderlinstr. Hlderlinstr 11 D-14050 Berlin - +49 30 3699904 0 www kardorff de D 14050 +49.30.3699904.0 www.kardorff.de

Reference image

PROJECT: ITCC Parcels Design LUMINAIRE: Cold Cathode / Wrapped Roof Contours DATE OF ISSUE: 03.09.2010 Dimensions DRAWN: wf
copyright by Kardorff Ingenieure Document protected by ISO 16016

REVISION / DATE: -

Kardorff Ingenieure Lightingdesign

46

Schematic light distribution

Product image

LUMINAIRE TYPE: T131 INSTALLATION TYPE: Canopy ceiling recessed INSTALLATION LOCATION: Entrance Canopy MANUFACTURER / NAME: WE-EF / DOC240 PRODUCT NUMBER: 134-0815 + 134-0798 (housing) LAMP / LIGHTCOLOUR: HIT-CE 70W / 840 PROTECTION LEVEL: IP 66 COLOUR OF HOUSING: Like Canopy Specified by Architect DIMENSIONS [MM]: Diameter: 250 Width: 222+245 Height: 237+17

570

Hlderlinstr. Hlderlinstr 11 D-14050 Berlin - +49 30 3699904 0 www kardorff de D 14050 +49.30.3699904.0 www.kardorff.de

270

PROJECT: ITCC Parcels Design LUMINAIRE: Downlight Main Entrance

305

DATE OF ISSUE: 03.09.2010 DRAWN: wf

REVISION / DATE: -

Reference image

Dimensions

Housing

Kardorff Ingenieure Lightingdesign

copyright by Kardorff Ingenieure Document protected by ISO 16016

47

Schematic light distribution

Product image

LUMINAIRE TYPE: T132 INSTALLATION TYPE: Floor recessed INSTALLATION LOCATION: Signage wall (WH-06) MANUFACTURER / NAME: ERCO / Tesis Focal Wall Washer PRODUCT NUMBER: 33671 LAMP / LIGHTCOLOUR: HIT-CE 20W / 830 PROTECTION LEVEL: IP 68 COLOUR OF HOUSING: Silver Grey DIMENSIONS [MM]: Length: 213 Height: 150 Width: 213 * housing is required

Hlderlinstr. Hlderlinstr 11 D-14050 Berlin - +49 30 3699904 0 www kardorff de D 14050 +49.30.3699904.0 www.kardorff.de

PROJECT: ITCC Parcels Design LUMINAIRE: Focal Wall Washer - Entrance faade DATE OF ISSUE: 03.09.2010 Reference image Dimensions i i DRAWN: wf
copyright by Kardorff Ingenieure Document protected by ISO 16016

REVISION / DATE: -

Kardorff Ingenieure Lightingdesign

48

Schematic light distribution

Product image

LUMINAIRE TYPE: T133 INSTALLATION TYPE: Floor recessed INSTALLATION LOCATION: Rock formation (KB01-02) MANUFACTURER / NAME: ERCO / Tesis Focal Wall Washer PRODUCT NUMBER: 33671 LAMP / LIGHTCOLOUR: HIT-CE 20W / 840 PROTECTION LEVEL: IP 68 COLOUR OF HOUSING: Silver Grey DIMENSIONS [MM]: Length: 213 Height: 150 Width: 213 * housing is required

Hlderlinstr. Hlderlinstr 11 D-14050 Berlin - +49 30 3699904 0 www kardorff de D 14050 +49.30.3699904.0 www.kardorff.de

PROJECT: ITCC Parcels Design LUMINAIRE: Focal Wall Washer Rock formation DATE OF ISSUE: 03.09.2010 Reference image Dimensions i i DRAWN: wf
copyright by Kardorff Ingenieure Document protected by ISO 16016

REVISION / DATE: -

Kardorff Ingenieure Lightingdesign

49

Schematic light distribution

Product image

LUMINAIRE TYPE: T134 INSTALLATION TYPE: Floor recessed INSTALLATION LOCATION: Hardscape Area / Light Points MANUFACTURER / NAME: ERCO / Tesis LED varychrome PRODUCT NUMBER: 33698 LAMP / LIGHTCOLOUR: LED 10W / RGB PROTECTION LEVEL: IP 68 COLOUR OF HOUSING: Silver Grey DIMENSIONS [MM]: Length: 213 Height: 150 Width: 213 * housing is required * To use with additional LED transformer

Hlderlinstr. Hlderlinstr 11 D-14050 Berlin - +49 30 3699904 0 www kardorff de D 14050 +49.30.3699904.0 www.kardorff.de

PROJECT: ITCC Parcels Design LUMINAIRE: Orientation light - Light Points DATE OF ISSUE: 03.09.2010 Reference image Dimensions i i DRAWN: wf
copyright by Kardorff Ingenieure Document protected by ISO 16016

REVISION / DATE: -

Kardorff Ingenieure Lightingdesign

50

Schematic light distribution

Product image

LUMINAIRE TYPE: T135 INSTALLATION TYPE: Surface mounted / Recessed INSTALLATION LOCATION: Lattice structure MANUFACTURER / NAME: Linear LED / VarioLED HighFlux PRODUCT NUMBER: LAMP / LIGHTCOLOUR: LED 24V, 60, 5000K, 700 lumens/m PROTECTION LEVEL: IP 67 COLOUR OF HOUSING: Aluminum DIMENSIONS [MM]: Length: 410 (module) Height: 9 Width:18.7 * To use with external LED transformer

Hlderlinstr. Hlderlinstr 11 D-14050 Berlin - +49 30 3699904 0 www kardorff de D 14050 +49.30.3699904.0 www.kardorff.de

PROJECT: ITCC Parcels Design LUMINAIRE: Lattice structure light lines DATE OF ISSUE: 03.09.2010 Reference image Dimensions DRAWN: wf
copyright by Kardorff Ingenieure Document protected by ISO 16016

REVISION / DATE: -

Kardorff Ingenieure Lightingdesign

51

Schematic light distribution

Product image

LUMINAIRE TYPE: T136 INSTALLATION TYPE: Surface mounted INSTALLATION LOCATION: Landscape areas / Crystalline paths MANUFACTURER / NAME: Modular / Ace of diamond PRODUCT NUMBER: 11350230 ( Ice White) LAMP / LIGHTCOLOUR: 2 x LED 1.44 W / cold white PROTECTION LEVEL: IP 67 COLOUR OF HOUSING: Ice White DIMENSIONS [MM]: Length: 300 Height: 120 Width: 220

Hlderlinstr. Hlderlinstr 11 D-14050 Berlin - +49 30 3699904 0 www kardorff de D 14050 +49.30.3699904.0 www.kardorff.de

PROJECT: ITCC Parcels Design LUMINAIRE: Ace of Diamond - Landscape areas Crystalline paths DATE OF ISSUE: REVISION / DATE: 03.09.2010 Reference image Dimensions DRAWN: wf
copyright by Kardorff Ingenieure Document protected by ISO 16016

Kardorff Ingenieure Lightingdesign

52

Schematic light distribution

Product image

LUMINAIRE TYPE: T137 INSTALLATION TYPE: Floor mounted INSTALLATION LOCATION: Main entrances faade entrance s MANUFACTURER / NAME: Schrder/Modullum Maxi PRODUCT NUMBER: LAMP / LIGHTCOLOUR: 4 x HIT-CE 150W / 840 PROTECTION LEVEL: IP 65 COLOUR OF HOUSING: Graphite DIMENSIONS [MM]: Height (one module): 610mm Height (total): 9500 Diameter: 245mm

Hlderlinstr. Hlderlinstr 11 D-14050 Berlin - +49 30 3699904 0 www kardorff de D 14050 +49.30.3699904.0 www.kardorff.de

PROJECT: ITCC Parcels Design LUMINAIRE: Pole luminaire faade lighting DATE OF ISSUE: 03.09.2010 Reference image g DRAWN: wf
copyright by Kardorff Ingenieure Document protected by ISO 16016

REVISION / DATE: -

Kardorff Ingenieure Lightingdesign

53

Schematic light distribution

Product image

LUMINAIRE TYPE: T138 INSTALLATION TYPE: Floor recessed INSTALLATION LOCATION: Tower s Towers wrapping envelope MANUFACTURER / NAME: ERCO PRODUCT NUMBER: 33716.000 LAMP / LIGHTCOLOUR: HIT-CE 35W / 830 PROTECTION LEVEL: IP 68 COLOUR OF HOUSING: Silver DIMENSIONS [MM]: Diameter: 247 Height: 365 * housing is required

Hlderlinstr. Hlderlinstr 11 D-14050 Berlin - +49 30 3699904 0 www kardorff de D 14050 +49.30.3699904.0 www.kardorff.de

PROJECT: ITCC Parcels Design LUMINAIRE: Floor recessed wallwasher DATE OF ISSUE: 03.09.2010 DRAWN: wf
copyright by Kardorff Ingenieure Document protected by ISO 16016

Reference image

Dimensions

REVISION / DATE: -

Kardorff Ingenieure Lightingdesign

54

g Schematic light distribution

Product image

Mounting position

LUMINAIRE TYPE: T139a INSTALLATION TYPE: Surface mounted INSTALLATION LOCATION: Tower s Towers flying ring (see opposite illustration) MANUFACTURER / NAME: Sill PRODUCT NUMBER: 903-021 3 007 33 LAMP / LIGHTCOLOUR: HIT-DE 70W / 830 PROTECTION LEVEL: IP 65 COLOUR OF HOUSING: Silver DIMENSIONS [MM]: Diameter: 271 Height: 326

Hlderlinstr. Hlderlinstr 11 D-14050 Berlin - +49 30 3699904 0 www kardorff de D 14050 +49.30.3699904.0 www.kardorff.de

PROJECT: ITCC Parcels Design LUMINAIRE: Parabolic projector DATE OF ISSUE: 03.09.2010 Reference image g Dimensions DRAWN: wf
copyright by Kardorff Ingenieure Document protected by ISO 16016

REVISION / DATE: -

Kardorff Ingenieure Lightingdesign

55

g Schematic light distribution

Product image

Mounting position

LUMINAIRE TYPE: T139b INSTALLATION TYPE: Surface mounted INSTALLATION LOCATION: Tower s Towers flying ring (see opposite illustration) MANUFACTURER / NAME: Sill PRODUCT NUMBER: 903-021 3 015 33 LAMP / LIGHTCOLOUR: HIT-DE 150W / 830 PROTECTION LEVEL: IP 65 COLOUR OF HOUSING: Silver DIMENSIONS [MM]: Diameter: 271 Height: 326

Hlderlinstr. Hlderlinstr 11 D-14050 Berlin - +49 30 3699904 0 www kardorff de D 14050 +49.30.3699904.0 www.kardorff.de

PROJECT: ITCC Parcels Design LUMINAIRE: Parabolic projector DATE OF ISSUE: 03.09.2010 Reference image g Dimensions DRAWN: wf
copyright by Kardorff Ingenieure Document protected by ISO 16016

REVISION / DATE: -

Kardorff Ingenieure Lightingdesign

56

g Schematic light distribution

Product image

Mounting position

LUMINAIRE TYPE: T139c INSTALLATION TYPE: Surface mounted INSTALLATION LOCATION: Tower s Towers flying ring (see opposite illustration) MANUFACTURER / NAME: Sill PRODUCT NUMBER: 903-021 3 025 33 LAMP / LIGHTCOLOUR: HIT-DE 250W / 830 PROTECTION LEVEL: IP 65 COLOUR OF HOUSING: Silver DIMENSIONS [MM]: Diameter: 271 Height: 326

Hlderlinstr. Hlderlinstr 11 D-14050 Berlin - +49 30 3699904 0 www kardorff de D 14050 +49.30.3699904.0 www.kardorff.de

PROJECT: ITCC Parcels Design LUMINAIRE: Parabolic projector DATE OF ISSUE: 03.09.2010 Reference image g Dimensions DRAWN: wf
copyright by Kardorff Ingenieure Document protected by ISO 16016

REVISION / DATE: -

Kardorff Ingenieure Lightingdesign

57

Schematic light distribution

Product image P d ti

LUMINAIRE TYPE: T140 INSTALLATION TYPE: Floor, semi-recessed INSTALLATION LOCATION: Paving-Main Fountain (WH-05 KB-03) (WH-05, MANUFACTURER / NAME: Cariboni / ZUVA PRODUCT NUMBER: 06ZU301AA4 + 06ZU901AA0 LAMP / LIGHTCOLOUR: HIT-CE 35W / 842 PROTECTION LEVEL: IP 67 COLOUR OF HOUSING: Like Paving Specified by Architect DIMENSIONS [MM]: Diameter: 223 Height: 31/437 * max. load 2.5 tonnes * housing is required

Luminaire installation housing: 600002004

Hlderlinstr. Hlderlinstr 11 D-14050 Berlin - +49 30 3699904 0 www kardorff de D 14050 +49.30.3699904.0 www.kardorff.de

PROJECT: ITCC Parcels Design LUMINAIRE: Accent light Paving DATE OF ISSUE: 03.09.2010 REVISION / DATE: -

Reference image

Dimensions

DRAWN: wf
copyright by Kardorff Ingenieure Document protected by ISO 16016

Kardorff Ingenieure Lightingdesign

58

Schematic light distribution

Product image P d ti

LUMINAIRE TYPE: T140 INSTALLATION TYPE: Floor, semi-recessed INSTALLATION LOCATION: Drop-off point (KB01-02) MANUFACTURER / NAME: Cariboni / ZUVA PRODUCT NUMBER: 06ZU301AA4 + 06ZU901AA0 LAMP / LIGHTCOLOUR: HIT-CE 35W / 842 PROTECTION LEVEL: IP 67 COLOUR OF HOUSING: DIMENSIONS [MM]: Diameter: 223 Height: 31/437 * max. load 2.5 tonnes * housing is required

Luminaire installation housing: 600002004

Hlderlinstr. Hlderlinstr 11 D-14050 Berlin - +49 30 3699904 0 www kardorff de D 14050 +49.30.3699904.0 www.kardorff.de

PROJECT: ITCC Parcels Design LUMINAIRE: Accent light DATE OF ISSUE: 03.09.2010 REVISION / DATE: -

Reference image

Dimensions

DRAWN: wf
copyright by Kardorff Ingenieure Document protected by ISO 16016

Kardorff Ingenieure Lightingdesign

59

Schematic light distribution

Product image

LUMINAIRE TYPE: T141a INSTALLATION TYPE: Floor recessed INSTALLATION LOCATION: Entrance faade (IT-02) MANUFACTURER / NAME: ERCO / Tesis PRODUCT NUMBER: 33723.000 LAMP / LIGHTCOLOUR: HIT-CE 70W / 840 PROTECTION LEVEL: IP 68 COLOUR OF HOUSING: Silver DIMENSIONS [MM]: Diameter: 297 Height: 410 * equipped with electronic control gear * housing is required

Hlderlinstr. Hlderlinstr 11 D-14050 Berlin - +49 30 3699904 0 www kardorff de D 14050 +49.30.3699904.0 www.kardorff.de

PROJECT: ITCC Parcels Design LUMINAIRE: Floor recessed wallwasher DATE OF ISSUE: 03.09.2010 Reference image Dimensions DRAWN: wf
copyright by Kardorff Ingenieure Document protected by ISO 16016

REVISION / DATE: -

Kardorff Ingenieure Lightingdesign

60

Schematic light distribution

Product image

LUMINAIRE TYPE: T141a INSTALLATION TYPE: Floor recessed INSTALLATION LOCATION: Signage wall (KB-03) MANUFACTURER / NAME: ERCO / Tesis PRODUCT NUMBER: 33723.000 LAMP / LIGHTCOLOUR: HIT-CE 70W / 840 PROTECTION LEVEL: IP 68 COLOUR OF HOUSING: Silver DIMENSIONS [MM]: Diameter: 297 Height: 410 * equipped with electronic control gear * housing is required

Hlderlinstr. Hlderlinstr 11 D-14050 Berlin - +49 30 3699904 0 www kardorff de D 14050 +49.30.3699904.0 www.kardorff.de

PROJECT: ITCC Parcels Design LUMINAIRE: Floor recessed wallwasher DATE OF ISSUE: 03.09.2010 Reference image Dimensions DRAWN: wf
copyright by Kardorff Ingenieure Document protected by ISO 16016

REVISION / DATE: -

Kardorff Ingenieure Lightingdesign

61

Schematic light distribution

Product image

LUMINAIRE TYPE: T141a INSTALLATION TYPE: Floor recessed INSTALLATION LOCATION: Metal cladded block MANUFACTURER / NAME: ERCO / Tesis PRODUCT NUMBER: 33723.000 LAMP / LIGHTCOLOUR: HIT-CE 70W / 840 PROTECTION LEVEL: IP 68 COLOUR OF HOUSING: Silver DIMENSIONS [MM]: Diameter: 297 Height: 410 * equipped with electronic control gear * housing is required

Hlderlinstr. Hlderlinstr 11 D-14050 Berlin - +49 30 3699904 0 www kardorff de D 14050 +49.30.3699904.0 www.kardorff.de

PROJECT: ITCC Parcels Design LUMINAIRE: Floor recessed wallwasher DATE OF ISSUE: 03.09.2010 Reference image Dimensions DRAWN: wf
copyright by Kardorff Ingenieure Document protected by ISO 16016

REVISION / DATE: -

Kardorff Ingenieure Lightingdesign

62

Schematic light distribution

Product image

LUMINAIRE TYPE: T141b INSTALLATION TYPE: Floor recessed INSTALLATION LOCATION: Metal cladded block MANUFACTURER / NAME: ERCO / Tesis PRODUCT NUMBER: 33729.000 LAMP / LIGHTCOLOUR: HIT-CE 150W / 840 PROTECTION LEVEL: IP 68 COLOUR OF HOUSING: Silver DIMENSIONS [MM]: Diameter: 297 Height: 410 * equipped with electronic control gear * housing is required

Hlderlinstr. Hlderlinstr 11 D-14050 Berlin - +49 30 3699904 0 www kardorff de D 14050 +49.30.3699904.0 www.kardorff.de

PROJECT: ITCC Parcels Design LUMINAIRE: Floor recessed wallwasher DATE OF ISSUE: 03.09.2010 Reference image Dimensions DRAWN: wf
copyright by Kardorff Ingenieure Document protected by ISO 16016

REVISION / DATE: -

Kardorff Ingenieure Lightingdesign

63

Schematic light distribution

Product image

LUMINAIRE TYPE: T142 INSTALLATION TYPE: Ceiling recessed INSTALLATION LOCATION: Entrance columns MANUFACTURER / NAME: BEGA PRODUCT NUMBER: 6825 + 443 (housing) LAMP / LIGHTCOLOUR: HIT-CE 35W/830 PROTECTION LEVEL: IP 65 COLOUR OF HOUSING: Silver DIMENSIONS [MM]: Diameter: 240 Height: 230 * equipped with electronic control gear * housing is required

202
Hlderlinstr. Hlderlinstr 11 D-14050 Berlin - +49 30 3699904 0 www kardorff de D 14050 +49.30.3699904.0 www.kardorff.de

230

250

PROJECT: ITCC Parcels Design LUMINAIRE: Ceiling recessed asymmetric downlight

202 240 Reference image Dimensions 320 Housing

DATE OF ISSUE: 03.09.2010 DRAWN: wf

REVISION / DATE: -

Kardorff Ingenieure Lightingdesign

copyright by Kardorff Ingenieure Document protected by ISO 16016

64

Schematic light distribution

Product image

LUMINAIRE TYPE: T143 INSTALLATION TYPE: Ceiling recessed INSTALLATION LOCATION: Planting areas MANUFACTURER / NAME: BEGA PRODUCT NUMBER: 6904 + 444 (housing) LAMP / LIGHTCOLOUR: HIT-CE 70W / 840 PROTECTION LEVEL: IP 65 COLOUR OF HOUSING: Silver DIMENSIONS [MM]: Diameter: 275 Height: 250 * equipped with electronic control gear * housing is required

240

Hlderlinstr. Hlderlinstr 11 D-14050 Berlin - +49 30 3699904 0 www kardorff de D 14050 +49.30.3699904.0 www.kardorff.de

250

270

PROJECT: ITCC Parcels Design LUMINAIRE: Ceiling recessed downlight DATE OF ISSUE: 03.09.2010 DRAWN: wf
copyright by Kardorff Ingenieure Document protected by ISO 16016

240 275 360 Housing

REVISION / DATE: -

Reference image

Dimensions

Kardorff Ingenieure Lightingdesign

65

Schematic light distribution Product image

LUMINAIRE TYPE: T144 INSTALLATION TYPE: Surface mounted INSTALLATION LOCATION: Shading screen MANUFACTURER / NAME: DGA / Starlight UP PRODUCT NUMBER: 760339.3 LAMP / LIGHTCOLOUR: 7 x LED 1W / 3200K PROTECTION LEVEL: IP 65 COLOUR OF HOUSING: Silver DIMENSIONS [MM]: Length: 98 mm Width: 80 mm Height: 105 mm * Optic: 30 lens * To use with external LED transformer

Hlderlinstr. Hlderlinstr 11 D-14050 Berlin - +49 30 3699904 0 www kardorff de D 14050 +49.30.3699904.0 www.kardorff.de

PROJECT: ITCC Parcels Design LUMINAIRE: Adjustable surface mounted LED spot DATE OF ISSUE: 03.09.2010 Reference image DRAWN: wf
copyright by Kardorff Ingenieure Document protected by ISO 16016

REVISION / DATE: -

Kardorff Ingenieure Lightingdesign

66

Schematic light distribution

Product image

LUMINAIRE TYPE: T145a INSTALLATION TYPE: Surface mounted INSTALLATION LOCATION: Roof walls/columns (IT02-03) MANUFACTURER / NAME: Meyer / Nightvision PRODUCT NUMBER: 8 747 054 000 LAMP / LIGHTCOLOUR: HIT-CE 35W / 830 PROTECTION LEVEL: IP 65 COLOUR OF HOUSING: Silver Grey DIMENSIONS [MM]: Length: 420 Height: 100 Width:162

Hlderlinstr. Hlderlinstr 11 D-14050 Berlin - +49 30 3699904 0 www kardorff de D 14050 +49.30.3699904.0 www.kardorff.de

PROJECT: ITCC Parcels Design LUMINAIRE: Surface mounted adjustable uplight DATE OF ISSUE: 03.09.2010 Reference image Dimensions DRAWN: wf
copyright by Kardorff Ingenieure Document protected by ISO 16016

REVISION / DATE: -

Kardorff Ingenieure Lightingdesign

67

Schematic light distribution

Product image

LUMINAIRE TYPE: T145a INSTALLATION TYPE: Wall mounted INSTALLATION LOCATION: Circular shading devices (KB-03) MANUFACTURER / NAME: Meyer / Nightvision PRODUCT NUMBER: 8 747 054 000 LAMP / LIGHTCOLOUR: HIT-CE 35W / 830 PROTECTION LEVEL: IP 65 COLOUR OF HOUSING: Silver Grey DIMENSIONS [MM]: Length: 420 Height: 100 Width:162

Hlderlinstr. Hlderlinstr 11 D-14050 Berlin - +49 30 3699904 0 www kardorff de D 14050 +49.30.3699904.0 www.kardorff.de

PROJECT: ITCC Parcels Design LUMINAIRE: Surface mounted adjustable uplight DATE OF ISSUE: 03.09.2010 Reference image Dimensions DRAWN: wf
copyright by Kardorff Ingenieure Document protected by ISO 16016

REVISION / DATE: -

Kardorff Ingenieure Lightingdesign

68

Schematic light distribution

Product image

LUMINAIRE TYPE: T145b INSTALLATION TYPE: Wall mounted INSTALLATION LOCATION: Circular shading devices (KB-03) MANUFACTURER / NAME: Meyer / Nightvision PRODUCT NUMBER: 8 741 054 000 LAMP / LIGHTCOLOUR: HIT-CE 70W / 830 PROTECTION LEVEL: IP 65 COLOUR OF HOUSING: Silver Grey DIMENSIONS [MM]: Length: 420 Height: 100 Width:162

Hlderlinstr. Hlderlinstr 11 D-14050 Berlin - +49 30 3699904 0 www kardorff de D 14050 +49.30.3699904.0 www.kardorff.de

PROJECT: ITCC Parcels Design LUMINAIRE: Surface mounted adjustable uplight DATE OF ISSUE: 03.09.2010 Reference image Dimensions DRAWN: wf
copyright by Kardorff Ingenieure Document protected by ISO 16016

REVISION / DATE: -

Kardorff Ingenieure Lightingdesign

69

Schematic light distribution

Product image

LUMINAIRE TYPE: T146 INSTALLATION TYPE: Floor recessed INSTALLATION LOCATION: Entrance faade Wall MANUFACTURER / NAME: ERCO / Tesis PRODUCT NUMBER: 33715.000 LAMP / LIGHTCOLOUR: HIT-CE 35W / 830 PROTECTION LEVEL: IP 68 COLOUR OF HOUSING: DIMENSIONS [MM]: Diameter: 247 Height: 365 * housing is required

Hlderlinstr. Hlderlinstr 11 D-14050 Berlin - +49 30 3699904 0 www kardorff de D 14050 +49.30.3699904.0 www.kardorff.de

PROJECT: ITCC Parcels Design LUMINAIRE: Wall Washer - Entrance faade DATE OF ISSUE: 03.09.2010 Reference image Dimensions i i DRAWN: wf
copyright by Kardorff Ingenieure Document protected by ISO 16016

REVISION / DATE: -

Kardorff Ingenieure Lightingdesign

70

Schematic light distribution

Product image

LUMINAIRE TYPE: T147 INSTALLATION TYPE: Suspended LED Mesh INSTALLATION LOCATION: Front Elevation (KB-03) MANUFACTURER / NAME: Traxon / IMAGIC WEAVE PRODUCT NUMBER: LAMP / LIGHTCOLOUR: LED / RGB PROTECTION LEVEL: IP 67 COLOUR OF HOUSING: DIMENSIONS [MM]: Length: 355-2980 Height: 13 Width: 23 * To use with external LED transformer * Lighting control required

Hlderlinstr. Hlderlinstr 11 D-14050 Berlin - +49 30 3699904 0 www kardorff de D 14050 +49.30.3699904.0 www.kardorff.de

PROJECT: ITCC Parcels Design LUMINAIRE: LED Mesh DATE OF ISSUE: 03.09.2010 Reference image Dimensions i i DRAWN: wf
copyright by Kardorff Ingenieure Document protected by ISO 16016

REVISION / DATE: -

Kardorff Ingenieure Lightingdesign

71

Schematic light distribution

Product image

LUMINAIRE TYPE: T147 INSTALLATION TYPE: Surface mounted LED Mesh INSTALLATION LOCATION: Shading structure (KB01-02) MANUFACTURER / NAME: Traxon / IMAGIC WEAVE PRODUCT NUMBER: LAMP / LIGHTCOLOUR: LED / RGB PROTECTION LEVEL: IP 67 COLOUR OF HOUSING: DIMENSIONS [MM]: Length: 355-2980 Height: 13 Width: 23 * To use with external LED transformer * Lighting control required

Hlderlinstr. Hlderlinstr 11 D-14050 Berlin - +49 30 3699904 0 www kardorff de D 14050 +49.30.3699904.0 www.kardorff.de

PROJECT: ITCC Parcels Design LUMINAIRE: LED Mesh DATE OF ISSUE: 03.09.2010 Reference image Dimensions i i DRAWN: wf
copyright by Kardorff Ingenieure Document protected by ISO 16016

REVISION / DATE: -

Kardorff Ingenieure Lightingdesign

72

Schematic light distribution

Product image

LUMINAIRE TYPE: T148 INSTALLATION TYPE: Ceiling recessed INSTALLATION LOCATION: Entrance Canopy MANUFACTURER / NAME: BEGA PRODUCT NUMBER: 6904 + 444 (housing) LAMP / LIGHTCOLOUR: HIT-CE 70W / 830 PROTECTION LEVEL: IP 65 COLOUR OF HOUSING: Silver DIMENSIONS [MM]: Diameter: 275 Height: 250 * equipped with electronic control gear * housing is required

240

Hlderlinstr. Hlderlinstr 11 D-14050 Berlin - +49 30 3699904 0 www kardorff de D 14050 +49.30.3699904.0 www.kardorff.de

250

270

PROJECT: ITCC Parcels Design LUMINAIRE: Ceiling recessed downlight DATE OF ISSUE: 03.09.2010 DRAWN: wf
copyright by Kardorff Ingenieure Document protected by ISO 16016

240 275 360 Housing

REVISION / DATE: -

Reference image

Dimensions

Kardorff Ingenieure Lightingdesign

73

Schematic light distribution Product image

LUMINAIRE TYPE: T149 INSTALLATION TYPE: Floor recessed INSTALLATION LOCATION: Walkways MANUFACTURER / NAME: Targetti / Mercure (Light line) PRODUCT NUMBER: LAMP / LIGHTCOLOUR: T16 24W / cold white PROTECTION LEVEL: IP 67 COLOUR OF HOUSING: DIMENSIONS [MM]: Width: 122 Length: 600 (module) Height: 51 * max. load 2 tonnes

Hlderlinstr. Hlderlinstr 11 D-14050 Berlin - +49 30 3699904 0 www kardorff de D 14050 +49.30.3699904.0 www.kardorff.de

PROJECT: ITCC Parcels Design LUMINAIRE: Recessed linear light DATE OF ISSUE: 03.09.2010 Reference image Dimensions DRAWN: wf
copyright by Kardorff Ingenieure Document protected by ISO 16016

REVISION / DATE: -

Kardorff Ingenieure Lightingdesign

74

Schematic light distribution

Product image

LUMINAIRE TYPE: T150 INSTALLATION TYPE: Floor recessed INSTALLATION LOCATION: Balustrade base MANUFACTURER / NAME: LED-Linear / VarioLED Flex Venus PRODUCT NUMBER: LAMP / LIGHTCOLOUR: LED / 5000K, 350lm/m PROTECTION LEVEL: IP 67 COLOUR OF HOUSING: DIMENSIONS [MM]: Width: 16 Lengths available: 269, 519, 1019, 2019 Height: 14.5 * To use with external LED transformer

16

varies
Hlderlinstr. Hlderlinstr 11 D-14050 Berlin - +49 30 3699904 0 www kardorff de D 14050 +49.30.3699904.0 www.kardorff.de

PROJECT: ITCC Parcels Design


14.5

LUMINAIRE: Linear light DATE OF ISSUE: 03.09.2010 DRAWN: wf


copyright by Kardorff Ingenieure Document protected by ISO 16016

varies

REVISION / DATE: -

Balustrade reference image

Dimensions

Kardorff Ingenieure Lightingdesign

75

Schematic light distribution Product image

LUMINAIRE TYPE: T151 INSTALLATION TYPE: Floor, semi-recessed INSTALLATION LOCATION: Entrance signage MANUFACTURER / NAME: ERCO/Tesis PRODUCT NUMBER: 33691.000 LAMP / LIGHTCOLOUR: HIT-CE 70W / 830 PROTECTION LEVEL: IP 68 COLOUR OF HOUSING: DIMENSIONS [MM]: Width: 260 Height: 266 * equipped with electronic control gear * housing is required

Hlderlinstr. Hlderlinstr 11 D-14050 Berlin - +49 30 3699904 0 www kardorff de D 14050 +49.30.3699904.0 www.kardorff.de

PROJECT: ITCC Parcels Design LUMINAIRE: Semi-recessed Semi recessed wallwasher DATE OF ISSUE: 03.09.2010 Reference image Dimensions DRAWN: wf
copyright by Kardorff Ingenieure Document protected by ISO 16016

REVISION / DATE: -

Kardorff Ingenieure Lightingdesign

76

Hlderlinstrae 11 D-14050 Berlin Tel.: 49 T l +49 (0)30 3699904 0 3699904-0 Fax.: +49 (0)30 3699904-99 berlin@kardorff.de www.kardorff.de
M1001_100903_Parcels-Design_Luminaire-Catalogue_wf.ppt

Вам также может понравиться