Академический Документы
Профессиональный Документы
Культура Документы
THEFT-DETERRENT SYSTEM
STRUCTURAL VIEW
1 2 3 4 5 6 7 8 9
Theft-deterrent control module Theft-deterrent relay Key reminder switch Ignition switch Door switch Bonnet switch Door lock-link switch Theft-deterrent horn Theft-deterrent horn relay
10 11 12 13 14 15 16 17
Flasher unit Security light Drivers door key cylinder switch Passengers door key cylinder switch Door lock timer unit Front turn light Front side turn light Rear combination light
BONNET SWITCH REMOVAL/INSTALLATION 1. Disconnect the negative battery cable. 2. Remove the theft-deterrent horn relay. (Refer to THEFT-DETERRENT HORN RELAY REMOVAL/INSTALLATION.) 3. Remove in the order indicated in the table. 4. Install in the reverse order of removal.
BONNET SWITCH INSPECTION 1. Disconnect the bonnet switch connector. 2. Inspect for continuity between the bonnet switch terminals using an ohmmeter. : Continuity
Switch position Closed Open Terminal A B
123
1 2 3 4
T33
THEFT-DETERRENT SYSTEM
THEFT-DETERRENT HORN RELAY REMOVAL/INSTALLATION 1. Disconnect the negative battery cable. 2. Remove the washer tank from the bracket. 3. Remove in the order indicated in the table. 4. Install in the reverse order of removal.
1 2 3
1 2 3
THEFT-DETERRENT RELAY INSPECTION 1. Remove the theft-deterrent relay. 2. Inspect for continuity between the theft-deterrent relay terminals using an ohmmeter. : Continuity B+: Battery positive voltage
Step 1 2 B+ GND Terminal A B C F E
THEFT-DETERRENT HORN RELAY INSPECTION 1. Remove the theft-deterrent horn relay. 2. Inspect for continuity between the theft-deterrent horn relay terminals using an ohmmeter. : Continuity B+: Battery positive voltage
Step 1 2 B+ GND Terminal A B C D
C E F C : A B F E
B
123456567
C C D A B
123456567
THEFT-DETERRENT CONTROL MODULE REMOVAL/INSTALLATION Note D Because the lock section of the relay is damaged easily, do not remove the relay from the bracket unless replacement is necessary. Always perform an inspection of the relay before removal. 1. Disconnect the negative battery cable. 2. Remove the flasher unit. (Refer to EXTERIOR LIGHTING SYSTEM, FLASHER UNIT REMOVAL/INSTALLATION.) 3. Remove in the order indicated in the table. 4. Install in the reverse order of removal.
3. If not as specified, replace the theft-deterrent horn relay. THEFT-DETERRENT RELAY REMOVAL/INSTALLATION 1. Disconnect the negative battery cable. 2. Remove the front side trim. (Refer to section S, TRIM, FRONT SIDE TRIM REMOVAL/INSTALLATION.) 3. Remove in the order indicated in the table. 4. Install in the reverse order of removal.
T34
THEFT-DETERRENT SYSTEM
1 2 3 4
Theft-deterrent control module connector Nut Bracket Theft-deterrent control module + Removal Note
Theft-deterrent Control Module Removal Note D Remove the theft-deterrent control module by prying the lock section of side part with a flathead screwdriver.
T35
THEFT-DETERRENT SYSTEM
THEFT-DETERRENT CONTROL MODULE INSPECTION (VEHICLES BUILT UP TO 07/2002) 1. Remove the theft-deterrent control module without disconnecting the connectors. 2. Measure the voltage at the theft-deterrent control module terminals as indicated below. 3. Disconnect the theft-deterrent control module connectors before inspecting for continuity at terminals 1F, 2K, 2M, 2N and 2R. 4. If not as specified, inspect the parts listed under inspection area and related wiring harnesses. 5. If the parts and wiring harnesses are okay but the system still does not work properly, replace the theft-deterrent control module. Terminal Voltage List (Reference) B+: Battery positive voltage
1F 1E 1D 1C 1B 1A
2S 2Q 2O 2M 2K 2I 2G 2E 2C 2A 2T 2R 2P 2N 2L 2J 2H 2F 2D 2B
Terminal
Signal
Connection
Voltage ( V ) /Continuity B+ 0 B+
Inspection area
D Ignition switch D ENGINE 15 A
1A 1B
Ignition switch at LOCK or ACC position Constant Ignition switch at ON position Turn switch on Turn switch off
Alternates 0 and B+ 0 Alternates 0 and B+ 0 Alternates 0 and B+ 0 Alternates 0 and B+ 0 Alternates 0 and B+ Turn light (LH) 0 Alternates 0 and B+ 0 Alternates 0 and B+ 0 Alternates 0 and B+ Turn light (RH) 0 Alternates 0 and B+ 0 Yes
D Turn switch D Hazard warning
1C
Flasher input
Hazard warning switch on Hazard warning switch off Theft-deterrent system alarm 1: Active Theft-deterrent system alarm 1: Other Ignition switch at ON position Turn switch on Turn switch off
switch
D Flasher unit
switch
D Flasher unit
1D
Turn (LH)
Hazard warning switch on Hazard warning switch off Theft-deterrent system alarm 1: Active Theft-deterrent system alarm 1: Other Ignition switch at ON position Turn switch on Turn switch off
1E
Turn (RH)
Hazard warning switch on Hazard warning switch off Theft-deterrent system alarm 1: Active Theft-deterrent system alarm 1: Other
1F
GND
T36
THEFT-DETERRENT SYSTEM
B+: Battery positive voltage
Terminal 2A 2B Signal Theft-deterrent horn on/off Key reminder switch on/off Connection Not used Not used Theft-deterrent horn relay Test condition Theft-deterrent system alarm 1: Active Theft-deterrent system alarm 1: Other Key reminder switch on Key reminder switch off Driver s door lock-link switch locked: inspect for continuity to ground Driver s door lock-link switch unlocked: inspect for continuity to ground Rear door lock-link switch locked: inspect for continuity to ground Rear door lock-link switch unlocked: inspect for continuity to ground Bonnet switch on: inspect for continuity to ground Bonnet switch off: inspect for continuity to ground Driver s or passenger s door locked with key Driver s or passenger s door unlocked with key Other Security light on Security light off Any door open: inspect for continuity to ground All doors closed: inspect for continuity to ground Theft-deterrent system alarm 1: Active Theft-deterrent system alarm 1: Other Voltage ( V ) /Continuity Inspection area
2C
Alternates 0 and B+ Theft-deterrent horn relay B+ B+ 0 No Driver s door lock-link switch Yes No Yes Yes Bonnet switch No 2.5 0 5 0 B+ Yes Door switch No 0 Theft-deterrent relay B+ Security light
D Driver s or
2D 2E 2F 2G 2H 2I 2J
Key reminder switch Not used Not used Not used Not used Not used Not used
D Door lock timer
2K
Lock/unlock
unit
D Driver s door
2M
Lock/unlock
2N
Bonnet open/closed
Bonnet switch
2O
cylinder switch D Passengers door key cylinder switch Not used Security light
2P 2Q
2R
Door open/closed
Door switch
2S
Theft-deterrent relay
2T
Not used
T37
THEFT-DETERRENT SYSTEM
THEFT-DETERRENT CONTROL MODULE INSPECTION (VEHICLES BUILT FROM 08/2002) 1. Remove the theft-deterrent control module without disconnecting the connectors. 2. Measure the voltage at the theft-deterrent control module terminals as indicated below. 3. Disconnect the theft-deterrent control module connectors before inspecting for continuity at terminals 1F, 2K, 2M, 2N and 2R. 4. If not as specified, inspect the parts listed under Action. D If the parts and wiring harnesses are okay but the system still does not work properly, replace the theft-deterrent control module. Terminal Voltage List (Reference)
Terminal
Signal
Connected to
Test condition Engine switch at ON position Engine switch a LOCK or ACC position Under any condition Under any condition: inspect for continuity to ground
Action
1A
IG1
ENGINE 15 A fuse
Below 1.0
1B 1C 1D 1E 1F 2A 2B
B+ Yes B+
D ROOM 10 A fuse
Theftdeterrent system alarm 1: Other Theftdeterrent system alarm 1: Active Key reminder switch on Key reminder switch off
2C
D Inspect theftdeterrent
horn relay
D Inspect related harness
2D
switch
D Inspect related harness
2E 2F 2G 2H 2I
T38
THEFT-DETERRENT SYSTEM
Terminal
Connected to
Test condition
Action
D Inspect keyless unit D Inspect related harness
2J
Keyless unit
D Door lock
2K
Lock/unlock
Driver s door lock link switch unlocked: inspect for continuity to ground Driver s door lock link switch unlocked: inspect for continuity to ground Passenger s and rear door lock link switch locked: inspect for continuity to ground Passenger s and rear door lock link switch unlocked: inspect for continuity to ground
No
D Inspect driver s door
locklink switch
D Inspect related harness
Yes
2L
No
D Passenger s
2M
Lock/unlock
D Inspect passenger s or
Yes
2N
Bonnet switch
Bonnet switch on: inspect for continuity to ground Bonnet switch off: inspect for continuity to ground Driver s or passenger s door locked with key or transmitter
Yes
D Inspect bonnet switch D Inspect related harness
No
D Driver s
2O
door key cylinder switch Passenger s door key cylinder switch keyless unit Instrument cluster Door lock timer unit
2.5
D Inspect driver s or
Below 1.0
passenger s door key cylinder switch D Inspect keyless unit (See KEYLESS UNIT INSPECTION) D Inspect related harness
Other Security light on Security light off Any door open: inspect for continuity to ground
2P 2Q
Security light
2R
Door open/closed
Door switch
No
T39
THEFT-DETERRENT SYSTEM
Terminal
Signal
Connected to
Test condition Theftdeterrent system alarm 1: Active Theftdeterrent system alarm 1: Other
Action
D Inspect flasher unit
2S
Flasher unit
2T
T40