Академический Документы
Профессиональный Документы
Культура Документы
141 141.1 D
Note: 50 and 75 GPM sizes have seal located in stuffing box area.
Cutaway View (Mechanical Seal Type) 50-75-100-135 GPM Sizes (11-17-23-31 m/hr)
SERIES 4125
MECHANICAL SEAL (SERIES 4125) G-HL, K-LL SIZES AK, AL, LS-M SIZES
BRACKET
200 PSI (14 BAR) for 100 SSU (21 cSt) and above 100 PSI (7 BAR) for below 100 SSU (21 cSt) -60F. to +650F. (-51C. to +343C.) 28 SSU to 2,000,000 SSU (0.1 cP to 440,000 cSt)
BRACKET
ROTOR
SHAFT
SHAFT
FEATURES
(Nominal Rating) It is the unique and unusually simple construction that has made our rotary pumps so adaptable to so many diversified installations. They possess excellent vacuum developing characteristics and operate equally well in either direction. Because of the cushioned action in providing a continuous and steady stream of liquid without foaming or churning, it is adaptable to an unlimited number of industrial applications. The rugged construction of these heavy-duty pumps assures long life and peak, trouble-free operation on normal-duty installation and outstanding performance when handling liquids at greater pressures. These heavy-duty pumps are furnished as standard with packed-type or mechanical seal construction for shaft protection and prevention of leakage. Packed pumps provide extra-deep stuffing box. The rotarytype mechanical seal works with, rather than against, pressure. It is self-adjusting and seals without leakage. Because of its method of sealing it prevents scoring of the pump drive shaft. The Series 4125 mechanical seal pumps can handle liquids with viscosities up to 15,000 SSU. Special seals for higher viscosities are available; consult factory.
Values shown represent minimums or maximums. Some special construction or
consideration may be required before a cataloged pump can be applied to an application involving maximum pressure or minimum or maximum temperature and/or viscosity. Certain models have restrictions in pressure and/or viscosities. See specifications, page 141.2, and performance curves.
(m/hr 2-3-7-11-17-23-31-32-45-68-95-114)
GPM 8-15-30-50-75-100135-140-200-300-420-500
2005
141 141.2 D
G, H, and HL Sizes
AK and AL Sizes
LS Size
Q and M Sizes
LQ and LL Sizes
QS Size
This series of heavy-duty pumps is available either revolvable casing feature on Page 141.1. Overpressure unmounted or mounted as shown on following pages. relief valve on head is standard for this series. To permit Available with packed stuffing box or Buna-N mechanical use of this type pump in a greater range of applications, seal with carbon rotating and Ni-Resist stationary faces. some sizes are available with jacketed head plate. For The integral thrust bearing is designed to handle heavyheavy-duty pumps with jacketed bracket and head, see duty pumping jobs without problems of end play and Catalog Section 142. distortion. For increased versatility of installation and Dimensions for Unmounted PumpsSee Page 141.8. complete selection of ports, many of the pump casings Performance Data for Unmounted PumpsSee Pages 141.15 through 141.42. are designed so they can be rotated on the bracket to any 45 or 90 angle from that shown in the illustrations. See CONSTRUCTION SERIES 125 AND 4125 (G THROUGH M SIZES)
Pump Construction Standard Construction Steel Fitted Bronze Fitted Casing Iron Iron Iron Head Iron Iron Iron Bracket Iron Iron Iron Rotor Iron Steel Bronze Idler Iron Iron Bronze Rotor Shaft And Idler Pin Steel Steel Steel Bushings Packed Idler Bronze Bronze Bronze Bracket Bronze Bronze Bronze Mechanical Seal Idler Carbon Graphite Carbon Graphite Carbon Graphite Bracket Bronze Bronze Bronze Internal Pressure Relief Valve Iron Iron Iron
Steel Fitted Construction Recommended Above This Viscosity SSU (cSt) 7,500 (1,650) 25,000 (5,500) 7,500 (1,650) 25,000 (5,500) 25,000 (5,500) 25,000 (5,500) 25,000 (5,500) 25,000 (5,500) 25,000 (5,500) 2,500 (550) 75,000 (16,500) 7,500 (1,650) 75,000 (16,500) 25,000 (5,500)
Maximum Recommended Discharge Pressure When Handling 100 SSU Liquid At Nominal Rated Speeds PSIG 200 200 200 150 150 200 200 200 200 200 150 150 150 150
Maximum Recommended Temperature for Cataloged Pump F. (C.) Packed 300 (149) 300 (149) 300 (149) 300 (149) 300 (149) 300 (149) 300 (149) 300 (149) 300 (149) 300 (149) 300 (149) 300 (149) 300 (149) 300 (149) Mech. Seal 225 (107) 225 (107) 225 (107) 225 (107) 225 (107) 225 (107) 225 (107) 225 (107) 225 (107) 225 (107) 225 (107) 225 (107) 225 (107) 225 (107)
Approximate Shipping Weight With Valve Pounds (KG) 22 38 40 78 81 105 110 155 175 185 190 440 540 600 (10) (17) (18) (35) (37) (48) (500 (70) (79) (84) (86) (200) (245) (272)
GPM (m/hr) 8 15 30 50 75 75 100 135 135 (2) (3) (7) (11) (17) (17) (23) (31) (31)
140 (32) 200 (45) 300 (68) 500 (114) 420 (95)
Buna-N elastomer used in mechanical seal of Series 4125 pumps. Viton , Neoprene, and Teflon mechanical seals also available. G, Q, and QS sizes have steel idler. For mechanical seal pumps on applications with viscosities above 15,000 SSU (3,300 cSt), provide details for recommendation. Ports are suitable for use with 125# ANSI cast iron or 150# ANSI steel companion flanges or flanged fittings. All others tapped for standard pipe. Standard seal can be used from -20F. to +225F. With special construction, temperatures from -60F. to +650F. can be handled with this series pumps. Nominal rating based on handling thin liquids. AK, AL, KK, LS, and QS sizes have ductile iron rotor.
Metric conversions are based on US measurements and rounded to the nearest whole number.
For maximum recommended discharge pressures when handling other viscosities and/or other speeds, see performance curves. Performance curves also show preferred constructions. If suction pressure exceeds 50 PSIG (3 BAR), consult factory. Check factory before using bronze rotors at viscosities normally requiring steelfitted construction. G, AK, AL, LS, and QS sizes not available in bronzefitted construction. AK, AL, LS, Q, QS, and M 4125 models furnished with carbon graphite bracket bushings and mechanical seal is mounted in stuffing box. Mechanical seal is mounted behind rotor in G, H, HL, K, KK, L, LQ, and LL pumps. AK and AL sizes not available in steel-fitted construction.
Teflon Registered trademark of E.I. DuPont Company. Viton Registered trademark of DuPont Dow Elastomers L.L.C.
2005
141 141.3 D
Heavy-duty pump Series 125 and 4125 are available with helical gear reducers that have been specifically developed for efficient operation with heavy-duty pumps. These rugged, compact, exceptionally quiet gear reducers come in three sizes: the small A size, medium B size, and large C size and are all bracket mounted requiring flexible couplings for both input and output shafts. The A size reducer, available with four gear ratios (2.24, 2.76, 3.43, and 4.17 to 1), is ideally suited for use with the G, H, HL, AK and AL size pumps. With the A size reducer and 1200 or 1800 RPM motors, the G, H, HL, AK, and AL size pumps can be used to cover a capacity range to 51 GPM. The medium size B helical gear reducer is available
with eight gear ratios from 1.87 to 1 to 7.65 to 1. This size normally is used with pump sizes AK through LS. With the B reducer, AK through LS pumps driven by 1200 or 1800 RPM motors can be used to cover a capacity range to 213 GPM. The large C size reducer also is available with seven gear ratios from 2.21 to 1 to 7.65 to 1. It is normally used with the KK through M size pumps. With the C reducer, KK through M size pumps driven by 1200 or 1800 RPM motors can cover a capacity range to 500 GPM.
Dimensions for R Drive Units See Pages 141.9 and 141.10. Performance Data for R Drive UnitsSee Pages 141.15 through 141.42.
2005
141 141.4 D
Model Numbers Packed G125R H125R HL125R AK125R AL125R K125R KK125R L125R LQ125R LL125R LS125R Q125R QS125R M125R Mech. Seal G4125R H4125R HL4125R AK4125R AL4125R K4125R KK4125R L4125R LQ4125R LL4125R LS4125R Q4125R QS4125R M4125R
Nominal Pump Rating GPM (m/hr) 8 15 30 50 75 75 (2) (3) (7) (11) (17) (17) RPM 1800 1800 1800 1200 1200 780 780 640 640 520 640 520 520 420
Maximum HydroStatic Pressure PSIG (BAR) 400 (28) 400 (28) 400 (28) 400 (28) 400 (28) 400 (28) 400 (28) 400 (28) 400 (28) 400 (28) 400 (28) 400 (28) 400 (28) 400 (28)
300 (149) 225 (107) 109 (49) 300 (149) 225 (107) 125 (57) 300 (149) 225 (107) 130 (59)
300 (149) 225 (107) 170 (77) 300 (136) 300 (149) 225 (107) 173 (79) 303 (138) 300 (149) 225 (107) 300 (149) 225 (107) 300 (149) 225 (107) 300 (149) 225 (107) 300 (149) 225 (107) 300 (149) 225 (107) 300 (149) 225 (107) 300 (149) 225 (107) 300 (149) 225 (107) ... ... ... ... ... ... ... ... ... 327 (148) 334 (152) 380 (173) 415 (188) 445 (202) 490 (222) ... ... ...
100 (23) 135 (31) 135 (31) 140 (32) 200 (45) 300 (68) 500 (114) 420 (95)
Buna-N elastomer used in mechanical seal of Series 4125 pumps. Viton Neoprene, and Teflon mechanical seals also available. For mechanical seal pumps on applications with viscosities above 15,000 SSU (3,300 cSt), provide details for recommendation. For maximum recommended discharge pressures when handling other viscosities and/or at other speeds, see performance curves. If suction pressure exceeds 50 PSIG (3 BAR), consult factory.
Metric conversions are based on US measurements and rounded to the nearest whole number.
Ports are suitable for use with 125# ANSI cast iron or 150# ANSI steel companion flanges or flanged fittings. All others tapped for standard pipe. Nominal rating based on handling thin liquids. Standard seal can be used form -20F. to +225F. With special construction, temperatures from -60F. to +650F. can be handled with this series pumps. AK and AL sizes not available in steel-fitted construction.
OUTSTANDING FEATURES 1. Mounts NEMA standard motors, 1200 or 1800 RPM. (5 HP, 1800 RPM maximum with A reducer; 15 HP, 1800 RPM maximum with B reducer; and 50 HP, 1800 RPM maximum with C reducer.) 2. Complete reducers within a size may be interchanged on a pump unit to obtain desired pump speeds and capacities. Thus the four gear ratios within the A size reducer may be interchanged within the size by selecting the proper pinion and gear of a common ratio. Similarly, all eight B reducers are interchangeble on each respective series of B reducer units. All seven C reducers are interchangeable on each respective series of C reducer units. 3. Quiet operation. High hardness helical gears run in a bath of oil. 4. Compact, narrow and low to fit in small space and low overhead.
5. Pump, motor, or reducer can be removed without disturbing the other two components. 6. Units with A, B and C reducers have standard flexible coupling with guard between power and reducer as well as between reducer and pump. 7. Oil and weathertight for outdoor service. 8. Ball bearings throughout. 9. Reducers easily adjustable to different motor center heights. 10. Self-supported. Not hung on pump or motor shafts. No radial load on pump or motor shafts. 11. A reducers have dia., key input and output shafts; B reducers have 1 dia., key input shaft and 1 dia., key output shaft; C reducers have 1 dia., key input and output shafts.
2005
141 141.5 D
LOW SPEED SHAFT RPM MAXIMUM REDUCER HP LOW SPEED SHAFT RPM MAXIMUM REDUCER HP LOW SPEED SHAFT RPM MAXIMUM REDUCER HP LOW SPEED SHAFT RPM MAXIMUM REDUCER HP
For input speeds higher than 1750 RPM, consult the factory. Horsepower ratings based on 8-10 hours operation per day, electric motor drive. See Catalog Section 610 for specific reducer sizing information.
For input speeds higher than 1750 RPM, consult the factory. Horsepower ratings based on 8-10 hours operation per day, electric motor drive. See Catalog Section 610 for specific reducer sizing information.
For input speeds higher than 1750 RPM, consult the factory. Horsepower ratings based on 8-10 hours operation per day, electric motor drive. See Catalog Section 610 for specific reducer sizing information.
2005
141 141.6 D
Heavy-duty Series 125 and 4125 packed and mechanical seal pumps in sizes from K through M are available in the P drive arrangement. These heavy-duty units are mounted on formed steel bases (K through LS sizes) and structural or formed steel bases (Q through M sizes) as illustrated above.
All mount separate heavy-duty reducers with flexible couplings between pump, reducer, and motor. Coupling guards as illustrated are standard construction. Contact factory for specifications and motor horsepower range.
Dimensions for P Drive Units Consult Factory. Performance Data for P Drive Units See Pages 142.27 through 141.42.
The Direct Drive D mounting is specifically designed for compactness and quietness of operation. In this type assembly the pump is mounted on one end of a rectangular formed steel base and connected to a motor by means of a flexible coupling with guard. G, H, and HL sizes can be directly connected to 1800 RPM motors as well as gearhead motors. AK and AL size pumps are direct connected to 1200 RPM motors or gearhead motors providing high-capacity, compact pumping unit.
Dimensions for D Drive Units (G through AL sizes) See Page 141.9. Performance Data for D Drive UnitsSee Pages 141.15 through 141.42.
2005
141 141.7 D
V-belt driven line of heavy-duty Series 125 and 4125 pumps are all mounted on formed welded steel bases. Pumps mount on pads to accept totally enclosed V-belt drive. All units in this series feature standard pump shaft extension with totally guarded V-driven pulley mounted on end of heavy-duty pump shaft. SPECIFICATIONS V DRIVE UNITS
Nominal Pump Rating GPM (m/hr) 8 (2) 15 (3) 30 (7) 75 (17) 100 (23) 135 (31) 135 (31) 140 (32) 200 (45) 300 (68) 500 (114) 420 (95) RPM 1800 1800 1800 780 780 640 640 520 640 520 520 420
Dimensions for V Drive UnitsSee Page 141.12. Performance Data for V Drive UnitsSee Pages 141.15 through 410.42.
Model Numbers Packed G125V H125V HL125V K125V KK125V L125V LQ125V LL125V LS125V Q125V QS125V M125V Mech. Seal G4125V H4125V HL4125V K4125V KK4125V L4125V LQ4125V LL4125V LS4125V Q4125V QS4125V M4125V
Maximum Hydrostatic Pressure PSIG (BAR) 400 (28) 400 (28) 400 (28) 400 (28) 400 (28) 400 (28) 400 (28) 400 (28) 400 (28) 400 (28) 400 (28) 400 (28)
Steel-Fitted Construction Recommended Above This Viscosity SSU (cSt) 7,500 (1,650) 25,000 (5,500) 7,500 (1,650) 25,000 (5,500) 25,000 (5,500) 25,000 (5,500) 25,000 (5,500) 2,500 (550) 75,000 (16,500) 7,500 (1,650) 75,000 (16,500) 25,000 (5,500)
Maximum Recommended Discharge Pressure When Handling 100 SSU Liquid At Nominal Rated Speeds PSIG 200 200 200 200 200 200 200 200 150 150 150 150
Maximum Recommended Temperature For Cataloged Pump, F. (C.) Packed 300 (149) 300 (149) 300 (149) 300 (149) 300 (149) 300 (149) 300 (149) 300 (149) 300 (149) 300 (149) 300 (149) 300 (149) Mech. Seal 225 (107) 225 (107) 225 (107) 225 (107) 225 (107) 225 (107) 225 (107) 225 (107) 225 (107) 225 (107) 225 (107) 225 (107)
Approximate Shipping Weight With Valve (Less Power) Pounds (KG) 93 109 114 255 265 305 340 365 375 986 1,100 1,138 (42) (49) (52) (116) (120) (138) (154) (166) (170) (448) (499) (517)
Buna-N elastomer used in mechanical seal of Series 4125 pumps. Viton, Neoprene, and Teflon mechanical seals also available. For mechanical seal pumps on applications with viscosities above 15,000 SSU (3,300 cSt), provide details for recommendation. For maximum recommended discharge pressures when handling other viscosities and/or at other speeds, see performance curves. If suction pressure
Metric conversions are based on US measurements and rounded to the nearest whole number.
exceeds 50 PSIG (3 BAR), consult factory. Ports are suitable for use with 125# ANSI cast iron or 150# ANSI steel companion flanges or flanged fittings. All others tapped for standard pipe. Nominal rating based on handling thin liquids. Standard seal can be used from -20F. to +225F. With special construction, temperatures from -60F. to +650F. can be handled with this series pumps.
Teflon Registered trademark of E.I. DuPont Company. Viton Registered trademark of DuPont Dow Elastomers L.L.C.
2005
141 141.8 D
These dimensions are average and not for construction purposes. Certified prints on request.
Ports are suitable for use with 125# ANSI cast iron or 150# ANSI steel companion flanges or flanged fittings. All others tapped for standard pipe.
A
1 1 2 2 2 in mm in mm in mm in mm in mm in mm in mm in mm in mm in mm
B
2.50 64 3.00 76 4.50 114 5.12 130 6.50 165 7.19 183 7.19 183 7.19 183 8.25 210 9.50 241
C
3.50 89 4.75 121 6.62 168 8.00 203 10.25 260 10.25 260 10.25 260 10.25 260 14.00 356 438
D
2.75 70 3.50 89 5.25 133 5.50 140 7.00 178 7.00 178 7.00 178 7.00 178 8.75 222 254
E
1.62 41 2.75 70 2.88 73 4.00 102 4.38 111 4.38 111 4.38 111 4.38 111 4.12 105 5.00 127
F
1.31 33 2.25 57 2.00 51 2.75 70 4.00 102 4.00 102 4.00 102 4.00 102 4.00 102 6.00 152
G
4.00 102 6.75 171 6.75 171 9.25 235 10.00 254 10.00 254 10.00 254 10.00 254 10.00 254 12.00 305
H
2.44 62 3.50 89 4.00 102 4.00 102 5.38 137 5.38 137 5.38 137 5.38 137 6.00 152 8.50 216
J
.34 9 .47 12 .41 10 .53 13 .53 13 .53 13 .53 13 .53 13 .69 18 .69 18
K
1.00 25 1.50 38 2.25 57 2.00 51 2.00 51 2.00 51 2.00 51 3.25 83 4.38 111 4.00 102
L
1.12 28 3.38 86 2.81 71 3.00 76 3.38 86 3.38 86 3.38 86 4.75 121 6.62 168 7.75 197
M
4.88 124 5.19 132 8.88 226 9.38 238 9.12 232 9.12 232 9.12 232 9.12 232 11.12 282 8.12 206
N
1.09 28 1.19 30 2.00 51 1.75 44 1.75 44 1.75 44 2.25 57 2.44 62 3.00 76 4.00 102
O
.31 8 .56 14 .44 11 .62 16 .62 16 .62 16 .62 16 .62 16 .75 19 1.00 25
P
.69 18 .62 16 1.00 25 .62 16 .62 16 .62 16 .62 16 .62 16 1.00 25 1.50 38
R
7.31 186 265 335 359 397 397 397 400 489 511
S
9.52 242 337 449 460 498 498 511 551 679 721
T
1.12 28 1.62 41 2.50 64 2.25 57 2.25 57 2.25 57 2.25 57 3.50 89 4.50 114 4.25 108
U
.50 13 .75 19.05 1.00 25.40 1.12 28.58 1.12 28.58 1.12 28.58 1.12 28.58 1.44 36.51 1.94 1.94
V
.12 x .06 3.05 x 1.52 .19 x .09 4.76 x 2.38 .25 x .12 6.35 x 3.18 .25 x .12 6.35 x 3.18 .25 x .12 6.35 x 3.18 .25 x .12 6.35 x 3.18 .25 x .12 6.35 x 3.18 .38 x .19 9.53 x 4.76 50 x .25 .50 x .25
W
2.69 68 2.88 73 4.80 122 5.12 130 5.38 137 5.38 137 5.38 137 5.19 132 8.19 208 8.50 216
10.44 13.25 13.18 17.68 14.12 18.12 15.62 19.62 15.62 19.62 15.62 20.12 15.75 21.69 19.25 26.75 20.12 28.38
M4125 4
17.25 10.00
2005
141 141.9 D
These dimensions are average and not for construction purposes. Certified prints on request.
DIMENSIONS SERIES 125 AND 4125 (R DRIVE) G THROUGH AL SIZE PUMPS A SIZE REDUCER UNITS
Base suitable for motor frames 56 through 184-T on Models G, H, and HL through 215-T for Models AK and AL. For motor frames 213-T and 215-T, G dimension is increased to 34.00. All other dimensions remain the same. (Base has open ends.) Does not apply to Models AK and AL. Location of pump port centerline on Models G125R and G4125R. With motor frames 182-T and smaller, use the (four) corner base anchor holes. Motor frame 184-T covers up the lower left corner anchor hole, so the hole 9.00 to the right is used. Does not apply to Models AK and AL. On Models G125R and G4125R, E dimension includes pump block. Base height is 2.94.
A 1
H 38 38 35
H125R H4125R AND AND 1 HL125R HL4125R AK125R AK4125R AND AND AL125R AL4125R
DIMENSIONS SERIES 125 AND 4125 (R DRIVE) AK THROUGH LS SIZE PUMPS B SIZE REDUCER UNITS
MODEL NUMBER PACKED SEAL
Ports are suitable for use with 125# ANSI cast iron or 150# ANSI steel companion flanges or flanged fittings. All others tapped for standard pipe. With motor frames 184-T and smaller, these units are assembled on a shorter base with the following dimension changes: (F = 16, G = 39, L = 3, N = 5). Motor rails 1 high are required with 56, 143-T and 145-T frame motors. NOTE: Motor frame larger than 256-T requires larger base. Consult factory. Units available to accept 10HP, 1200 RPM maximum motor. NOTE: Motor rails 2 high are required on L through LS size units with 184-T or 4 center height motors.
AK125R AND AL125R AND KK125R L125R LQ125R LL125R LS125R AK4125R AND AL4125R AND KK4125R L4125R
A 2 2 2 in mm in mm in mm
J 35 35 35 35 35 35
M 6.80 173 6.88 175 7.12 181 7.12 181 7.62 194 7.62 194
N 4.88 124 4.25 108 4.62 117 4.62 117 4.62 117 4.62 117
K125R K4125R
6.50 11.00 4.00 14.25 48.00 1.38 7.19 11.00 4.00 14.25 48.00 1.38 7.19 11.00 4.00 14.25 48.00 1.38 7.19 11.00 4.00 14.25 48.00 1.38
in LQ4125R 2 mm
LL4125R LS4125R
3 3
in mm in mm
2005
141 141.10 D
DIMENSIONS
These dimensions are average and not for construction purposes. Certified prints on request.
DIMENSIONS SERIES 125 AND 4125 (R DRIVE) KK THROUGH M SIZE PUMPS (NOT FOR QS SIZE) C SIZE REDUCER UNITS
MODEL NUMBER PACKED
KK125R
SEAL
KK4125R
A 2 in mm in mm in mm in mm in mm in mm in mm
L 3.00 76 0 0 0 0 0 0 1.38 35
M 6.88 175 7.12 181 7.12 181 7.62 194 7.62 194
N 6.06 154 5.75 146 5.75 146 5.75 146 5.75 146
5.12 13.75 6.00 21.00 49.00 1.50 130 349 152 533 1245 38
L125R
L4125R
2 2 3 3 4 4
6.50 13.75 6.00 19.75 59.50 1.50 165 349 152 502 1511 38
LQ125R
LQ4125R
7.19 13.75 6.00 19.75 59.50 1.50 183 349 152 502 1511 38
LL125R
LL4125R
7.19 13.75 6.00 19.75 59.50 1.50 183 349 152 502 1511 38
LS125R
LS4125R
7.19 13.75 6.00 19.75 59.50 1.50 183 349 152 502 1511 38
Q125R
Q4125R
8.25 14.75 6.00 19.75 59.50 1.50 210 375 152 502 1511 38
M125R
M4125R
9.50 16.00 6.00 19.75 59.50 1.50 241 406 152 502 1511 38
DIMENSIONS SERIES 125 AND 4125 QS SIZE PUMPS C SIZE REDUCER UNITS
2005
141 141.11 D
These dimensions are average and not for construction purposes. Certified prints on request.
DIMENSIONS SERIES 125 AND 4125 (D DRIVE) G SIZE PUMPS DIRECT CONNECTED UNITS
B in mm G125D
OR
in mm in mm in mm
G4125D
DIMENSIONS SERIES 125 AND 4125 (D DRIVE) H THROUGH AL SIZE PUMPS DIRECT CONNECTED UNITS
MODEL NUMBER PACKED SEAL A 1
H125D OR H4125D OR HL4125D
B in mm in mm in mm in mm in mm in mm in mm 3.00 76 3.00 76 3.00 76 4.50 114 4.50 114 4.50 114 4.50 114
D 3.50 89 4.50 114 5.25 133 5.25 133 5.25 133 6.25 159 7.00 178
F 20.50 521 25.00 635 25.00 635 26.00 660 29.00 737 39.00 991 39.00 991
M 4.06 103 4.06 103 4.06 103 6.80 173 6.80 173 6.80 173 6.80 173
N 8.50 216 9.00 229 9.00 229 9.00 229 9.00 229 16.00 406 16.00 406
S 4.25 108 4.50 114 4.50 114 4.50 114 4.50 114 8.00 203 8.00 203
1 1 2
For motor frames 56, 143-T, and 145-T. (Base has open ends.) For motor frames 182, 182-T, 184, and 184-T. (Base has closed ends.) For motor frames 213 through 215-T. (Base has closed ends.) For motor frames 182 through 184-T. Dimension includes block under motor. (Base has open ends.) For motor frames 213 through 215-T. (Base has open ends.) For motor frames 254 through 256-T. (Base has closed ends.) For motor frames 284 through 286-T. (Base has closed ends.)
HL125D
AK125D OR AL125D
AK4125D OR AL4125D
2 2 2
2005
141 141.12 D
These dimensions are average and not for construction purposes. Certified prints on request.
DIMENSIONS SERIES 125 AND 4125 (V DRIVE) G SIZE PUMPS V-BELT DRIVE UNITS
NOTE: For motor frames 56 and 143-T. Maximum frame size is 143-T. D dimension for motor frame 56 is 3.50 (89 mm) less rail; for motor frame 143-T, 5.00 (127 mm) with rail. NOTE: Dimensions shown in parentheses are millimeters; others are inches.
DIMENSIONS SERIES 125 AND 4125 (V DRIVE) H THROUGH M SIZE PUMPS V-BELT DRIVE UNITS
A 1 2 2 2 3 3 4 4 in mm in mm in mm in mm in mm in mm in mm in mm B
3.00 76 5.12 130 650 165 7.19 183 7.19 183 7.19 183 8.25 210 9.50 241
SEAL
AND
C
9.25 235 13.81 351 15.31 389 15.31 389 15.31 389 15.31 389 21.25 540 22.50 572
E
1.75 44 3.25 83 3.25 83 3.25 83 3.25 83 3.25 83 6.00 152 6.00 152
F
14.75 375 17.00 432 17.00 432 17.00 432 17.00 432 17.00 432 21.00 533 21.00 533
G
23.75 603 28.75 730 28.75 730 28.75 730 28.75 730 28.75 730 49.00 1245 49.00 1245
J
.75 19 1.00 25 1.00 25 1.00 25 1.00 25 1.00 25 1.50 38 1.50 38
K
.50 13 .50 13 .50 13 .50 13 .50 13 .50 13 .81 21 .81 21
L
4.88 124 2.50 64 2.25 57 2.25 57 2.25 57 1.06 27 2.75 70 2.12 54
M
4.06 103 6.88 175 7.12 181 7.12 181 7.62 194 7.62 194 11.19 284 12.50 318
N
4.25 108 5.25 133 5.25 133 5.25 133 5.25 133 5.25 133 8.50 216 8.50 216
L4125V
LQ125V
LQ4125V
LL125V
LL4125V
LS125V Q125V
LS4125V
Ports are suitable for use with 125# ANSI cast iron or 150# ANSI steel companion flanges or flanged fittings. All others tapped for standard pipe. Base dimensions correct for all motors. Base dimensions correct through frame 215-T motors and 19 OD sheaves. Larger motors and/or 25 OD sheaves require larger base. QS size pump drawing available on request.
Q4125V
M125V
M4125V
2005