Академический Документы
Профессиональный Документы
Культура Документы
SERVICE MANUAL
INTEGRATED COLOR TV / STEREO VIDEO CASSETTE RECORDER BASIC TAPE MECHANISM : OVD-6
SPECIFICATIONS
GENERAL POWER REQUIREMENTS ................. 120V AC, 60Hz POWER CONSUMPTION ................... 89W TYP 4W (power save mode) WEIGHT .............................................. 13.5 kg (29.8 lbs.) DIMENSIONS ...................................... 435 mm (W) x 370.5 mm (D) x 384.5 mm (H) (17 1/4 x 14 5/8 x 15 1/4 in.) TV SECTION PICTURE TUBE .................................. 208 mm (W) x 211 mm (H) (8 1/4 x 8 3/8 in.) 335 mm (diagonal) (13 in.) TUNER SYSTEM ................................ Frequency synthesized tuner CHANNEL COVERAGE ...................... VHF: 2 to 13 UHF: 14 to 69 CATV: 5A, A-1 to A-5, A to W, W+1 to W+84 PROGRAM MEMORY ......................... 181 TV SYSTEM ........................................ M HORIZONTAL RESOLUTION ............ 230 lines ANTENNA INPUT ............................... 75 ohms, unbalanced VCR SECTION OPERATING TEMPERATURE ........... 5C to 40C VIDEO RECORDING SYSTEM .......... Rotary 2 head helical scanning system and specifications are subject to change without Design notice. VIDEO SIGNAL SYSTEM ................ NTSC color system, 525 lines, 60 fields VIDEO HEAD ................................... Azimuth 2 head USABLE CASSETTES ..................... VHS video cassette S-VHS video cassette (play back only) TAPE SPEED ................................... SP: 33.35 mm/sec LP: 16.67 mm/sec SLP: 11.12 mm/sec RECORDING/PLAYBACK TIME ..... SP: 3 hours with T-180 tape LP: 6 hours with T-180 tape SLP: 9 hours with T-180 tape VIDEO INPUT ................................... 1.0Vp-p, 75 ohm, unbalanced VIDEO OUTPUT .............................. 1.0Vp-p, 75 ohm, unbalanced VIDEO S/N ....................................... 53dB (nominal) AUDIO INPUT .................................. 8dBs, 50K ohm AUDIO OUTPUT .............................. 8dBs, less than 1K ohm AUDIO TRACK ................................. 1 tracks (Normal sound) FAST-FORWARD TIME ................... Approx. 2 minutes 15 seconds with T-120 tape REWIND TIME ................................. Approx. 1 minute 48 seconds with T-120 tape
DA TA
TABLE OF CONTENTS
SPECIFICATIONS .............................................................................................................................................................. COVER TABLE OF CONTENTS ..................................................................................................................................................... A1-1 SERVICING NOTICES ON CHECKING ............................................................................................................................. A2-1 DISASSEMBLY INSTRUCTIONS REMOVAL OF MECHANICAL PARTS AND P.C. BOARDS ........................................................................................... B1-1, B1-2 REMOVAL OF DECK PARTS .......................................................................................................................................... B2-1~B2-5 REMOVAL OF ANODE CAP ............................................................................................................................................ B3-1 KEY TO ABBREVIATIONS ................................................................................................................................................. C1-1, C1-2 SERVICE MODE LIST ....................................................................................................................................................... C2-1 PREVENTIVE CHECKS AND SERVICE INTERVALS ....................................................................................................... C3-1, C3-2 NOTE FOR THE REPLACING OF MEMORY IC ................................................................................................................ C4-1 SERVICING FIXTURES AND TOOLS ................................................................................................................................ C5-1 PREPARATION FOR SERVICING ..................................................................................................................................... C5-2, C5-3 VCR TEST TAPE INTERCHANGEABILITY TABLE ........................................................................................................... C6-1 MECHANICAL ADJUSTMENTS CONFIRMATION AND ADJUSTMENT ............................................................................................................................ D1-1, D1-2 CONFIRMATION AND ADJUSTMENT OF TAPE RUNNING MECHANISM .................................................................. D1-2, D1-3 MECHANISM ADJUSTMENT PARTS LOCATION GUIDE ............................................................................................. D1-4 ELECTRICAL ADJUSTMENTS ADJUSTMENT PROCEDURE ......................................................................................................................................... D2-1 BASIC ADJUSTMENTS ................................................................................................................................................... D2-1~D2-4 ELECTRICAL ADJUSTMENT PARTS LOCATION GUIDE ............................................................................................. D2-5, D2-6 PURITY AND CONVERGENCE ADJUSTMENTS .......................................................................................................... D2-7 TROUBLESHOOTING GUIDES .......................................................................................................................................... E-1~E-26 IC DESCRIPTIONS ............................................................................................................................................................ F1-1~F1-3 SERVO TIMING CHART .................................................................................................................................................... F2-1 SYSTEM SWITCH MODE ................................................................................................................................................... F2-2 SEMICONDUCTOR BASE CONNECTIONS ...................................................................................................................... G-1 BLOCK DIAGRAMS TV .................................................................................................................................................................................... H-1 Y/C/AUDIO/HEAD AMP/IN/OUT ...................................................................................................................................... H-2 MICON/POWER/OPERATION ......................................................................................................................................... H-3 PRINTED CIRCUIT BOARDS (OPERATION/DECK) ......................................................................................................... I-1 OPERATION SCHEMATIC DIAGRAM ............................................................................................................................... I-2 DECK SCHEMATIC DIAGRAM ........................................................................................................................................... I-3 PRINTED CIRCUIT BOARDS (SYSCON) .......................................................................................................................... I-4~I-6 Y/C/AUDIO/HEAD AMP SCHEMATIC DIAGRAM .............................................................................................................. I-7 MICON SCHEMATIC DIAGRAM ......................................................................................................................................... I-8 CHROMA/IF SCHEMATIC DIAGRAM ................................................................................................................................ I-9 IN/OUT SCHEMATIC DIAGRAM ........................................................................................................................................ I-10 POWER SCHEMATIC DIAGRAM ....................................................................................................................................... I-11 SOUND AMP SCHEMATIC DIAGRAM ............................................................................................................................... I-12 PRINTED CIRCUIT BOARDS (MAIN/CRT) ........................................................................................................................ I-13 DEFLECTION SCHEMATIC DIAGRAM .............................................................................................................................. I-14 TV POWER SCHEMATIC DIAGRAM ................................................................................................................................. I-15 CRT SCHEMATIC DIAGRAM ............................................................................................................................................. I-16 INTERCONNECTION DIAGRAM ........................................................................................................................................ I-17 WAVEFORMS .................................................................................................................................................................... J-1~J-3 MECHANICAL EXPLODED VIEW ...................................................................................................................................... K1-1, K1-2 MECHANICAL REPLACEMENT PARTS LIST ................................................................................................................... K1-3 ACCESSORY REPLACEMENT PARTS LIST .................................................................................................................... K1-3 CHASSIS EXPLODED VIEW (TOP VIEW) ......................................................................................................................... K2-1 CHASSIS EXPLODED VIEW (BOTTOM VIEW) ................................................................................................................. K2-2 CHASSIS REPLACEMENT PARTS LIST ........................................................................................................................... K2-3 ELECTRICAL REPLACEMENT PARTS LIST ..................................................................................................................... K3-1~K3-4
A1-1
6. AVOID AN X-RAY
Safety is secured against an X-ray by considering about the cathode-ray tube and the high voltage peripheral circuit, etc. Therefore, when repairing the high voltage peripheral circuit, use the designated parts and make sure not modify the circuit. Repairing except indicates causes rising of high voltage, and it emits an X-ray from the cathode-ray tube.
4. PUT PARTS AND WIRES IN THE ORIGINAL POSITION AFTER ASSEMBLING OR WIRING
There are parts which use the insulation material such as a tube or tape for safety, or which are assembled in the condition that these do not contact with the printed board. The inside wiring is designed not to get closer to the pyrogenic parts and high voltage parts. Therefore, put these parts in the original positions.
1. Unplug the plug from the AC outlet. 2. Remove the antenna terminal on TV and turn on the TV. 3. Insulation resistance between the cord plug terminals and the eternal exposure metal [Note 2] should be more than 1M ohm by using the 500V insulation resistance meter [Note 1]. 4. If the insulation resistance is less than 1M ohm, the inspection repair should be required.
[Note 1]
If you have not the 500V insulation resistance meter, use a Tester.
[Note 2]
A2-1
DISASSEMBLY INSTRUCTIONS
1. REMOVAL OF MECHANICAL PARTS AND P.C. BOARDS
1-1: BACK CABINET (Refer to Fig. 1-1) 1. Remove the 2 screws 1. 2. Remove the 2 screws 2. 3. Remove the 2 screws 3 which are used for holding the Back Cabinet. 4. Remove the AC cord from the AC cord hook 4. 5. Remove the Back Cabinet in the direction of arrow.
Front Cabinet
1-3: TV/VCR BLOCK (Refer to Fig. 1-3) 1. Remove the 2 screws 1. 2. Disconnect the following connectors: (CP351, CP352, CP353, CP354, CP401 and CP502). 3. Unlock the support 2. 4. Remove the TV/VCR Block in the direction of arrow.
1
Front Cabinet
2
UP TO RELEASE
TV/VCR Block
Fig. 1-3
2 3 3 2 4
Back Cabinet
1-4: MAIN PCB (Refer to Fig. 1-4) 1. Remove the screw 1. 2. Remove the Main PCB Holder. 3. Remove the 2 screws 2. 4. Remove the 3 screws 3. 5. Disconnect the following connectors: (CP810, CP820, CP811 and CP804). 6. Remove the Main PCB in the direction of arrow.
2 2
Main PCB
Fig. 1-1 1-2: CRT PCB (Refer to Fig. 1-2) CAUTION: BEFORE REMOVING THE ANODE CAP, DISCHARGE ELECTRICITY BECAUSE IT CONTAINS HIGH VOLTAGE. BEFORE ATTEMPTING TO REMOVE OR REPAIR ANY PCB, UNPLUG THE POWER CORD FROM THE AC SOURCE. 1. Remove the Anode Cap. (Refer to REMOVAL OF ANODE CAP) 2. Disconnect the following connectors: (CP801, CP802 and CP850). 3. Remove the CRT PCB in the direction of arrow.
Front Cabinet CRT PCB
VCR Block
Fig. 1-4
Fig. 1-2
B1-1
DISASSEMBLY INSTRUCTIONS
1-5: DECK SHIELD PLATE (Refer to Fig. 1-5) 1. Remove the 2 screws 1. 2. Remove the screw 2. 3. Remove the Deck Shield Plate in the direction of arrow.
Deck Shield Plate
1-7: JACK PLATE AND SYSCON PCB (Refer to Fig. 1-7) 1. Remove the screw 1. 2. Remove the Syscon PCB in the direction of arrow (A). 3. Remove the screw 2. 4. Remove the nut 3. 5. Remove the washer 4. 6. Unlock the 2 supports 5. 7. Remove the Jack Plate in the direction of arrow (B).
Jack Plate
2 1
1 5
Syscon PCB (B)
2 3 4 5
Fig. 1-5 1-6: DECK CHASSIS (Refer to Fig. 1-6) 1. Remove the 3 screws 1. 2. Disconnect the following connectors: (CP1002, CP1005, CP1006, CP4001, CP4004 and CP4005). 3. Remove the Deck Chassis in the direction of arrow.
1 1 1
Deck Holder
Fig. 1-7
Deck Chassis
Syscon PCB
Fig. 1-6
B1-2
DISASSEMBLY INSTRUCTIONS
2. REMOVAL OF DECK PARTS
2-1: TOP BRACKET (Refer to Fig. 2-1) 1. Remove the 2 screws 1. 2. Slide the 2 supports 2 and remove the Top Bracket. NOTE
Tape Guide L
NOTE When you install the Tape Guide L, install as shown in the circle of Fig. 2-3-B. (Refer to Fig. 2-3-B)
When you install the Top Bracket, install the screw (1) first, then install the screw (2).
REC Lever (2)
1
Top Bracket
(1)
Top Bracket The REC Lever is not installed on the Video Cassette Player.
Fig. 2-3-B
1. Move the Cassette Holder Ass'y to the front side. 2. Push the Locker R to remove the Cassette Side R. 3. Remove the Cassette Side L. Fig. 2-1
Cassette Side R Main Chassis Locker R
2-2: FLAP LEVER/TAPE GUIDE R (Refer to Fig. 2-2) 1. Move the Cassette Holder Ass'y to the back side. 2. Remove the Polyslider Washer 1. 3. Remove the Flap Lever. 4. Unlock the 3 supports 2 and remove the Tape Guide R.
Fig. 2-4 2-5: CASSETTE SIDE L/R (Refer to Fig. 2-5) 1. Remove the Locker Spring. 2. Unlock the 4 supports 1 and then remove the Cassette Side L/R. NOTE When you install the Cassette Side L/R, be sure to move the Locker L/R after installing.
1 1
Locker Spring
2 2 1
Main Chassis
Fig. 2-2
2-3: TAPE GUIDE L (Refer to Fig. 2-3-A) 1. Move the Cassette Holder Ass'y to the back side. 2. Unlock the 2 supports 1 and remove the Tape Guide L. 3. Remove the REC Lever. (Recorder only)
Fig. 2-5
1
Main Chassis The REC Lever is not installed on the Video Cassette Player.
Fig. 2-3-A
B2-1
DISASSEMBLY INSTRUCTIONS
2-6: LINK ASS'Y (Refer to Fig. 2-6) 1. Set the Link Ass'y to the Eject position. 2. Remove the (A) side of the Link Ass'y first, then remove the (B) side. 2-9: TENSION ASS'Y (Refer to Fig. 2-9-A) 1. Move the Inclined S Ass'y to the back side. 2. Unlock the support 1 and remove the S Reel Stopper. 3. Remove the Tension Spring. 4. Unlock the support 2 and remove the Tension Arm Ass'y. 5. Remove the Tension Adjust. 6. Unlock the 2 supports 3 and remove the Tension Band Ass'y. 7. Unlock the support 4 and remove the Tension Holder.
Tension Adjust (B) (A) Link Ass'y
Link Ass'y
3 3
Tension Band Ass'y
Fig. 2-6
2-7: LOADING MOTOR ASS'Y (Refer to Fig. 2-7) 1. Remove the Link Lever. 2. Remove the Dumper Spring. 3. Remove the 2 screws 1. 4. Unlock the support 2 and remove the Loading Motor Ass'y. 5. Unlock the 2 supports 3 and remove the Deck PCB (BOT).
1
Loading Motor Ass'y S Reel Stopper
2 4 1
Tension Holder
Inclined S Ass'y
Fig. 2-9-A NOTE When you install the Tension Adjust, install as shown in Fig. 2-9-B. (Refer to Fig. 2-9-B)
Adjust the direction of the Marker to inside.
Dumper Spring
3
Main Chassis
1
Deck PCB (BOT) Link Lever
Fig. 2-9-B 2-10: T BRAKE ASS'Y (Refer to Fig. 2-10) 1. Remove the T Brake Spring. 2. Remove the T Brake Ass'y.
T Brake Ass'y
Fig. 2-7
2-8: SENSOR COVER L (Refer to Fig. 2-8) 1. Unlock the support 1 and remove the Sensor Cover L. 2. Unlock the 2 supports 2 and remove the Deck PCB (EOT).
T Brake Spring
Main Chassis
Fig. 2-10
1 2
Fig. 2-8
B2-2
DISASSEMBLY INSTRUCTIONS
2-11: S REEL/T REEL ASS'Y (Refer to Fig. 2-11) 1. Remove the Idler Ass'y. 2. Remove the S Reel and T Reel Ass'y. 3. Remove the 2 Polyslider Washers 1. NOTE 1. Take care not to damage the gears of the S Reel, T Reel Ass'y and Idler Ass'y. 2. The Polyslider Washer may be remained on the back of the reel. 3. Take care not to damage the shaft. 4. Do not touch the section "A" of S Reel and T Reel Ass'y. (Use gloves.) (Refer to Fig. 2-11) Do not adhere the stains on it. 5. When you install the reel, clean the shaft and oil it (KYODO OIL Slidas #150). (If you do not oil, noise may be heard in FF/REW mode.) 6. After installing the reel, adjust the height of the reel. (Refer to MECHANICAL ADJUSTMENT) NOTE 1. Do not touch the Pinch Roller. (Use gloves.) 2. When you install the Pinch Roller Ass'y, install as shown in the circle. (Refer to Fig. 2-12-B)
Fig. 2-12-B 2-13: A/C HEAD (Refer to Fig. 2-13-A) 1. Remove the screw 1. 2. Remove the A/C Head Base. 3. Remove the 3 screws 2. 4. Remove the A/C Head and A/C Head Spring. NOTE 1. Do not touch the A/C Head. (Use gloves.) 2. When you install the A/C Head Spring, install as shown in Fig. 2-13-B. (Refer to Fig. 2-13-B) 3. When you install the A/C Head, tighten the screw (1) first, then tighten the screw (2), finally tighten the screw (3).
(1) (3)
(A)
T Reel Ass'y
1
(A)
Fig. 2-11 2-12: PINCH ROLLER ASS'Y/P5 ARM ASS'Y (Refer to Fig. 2-12-A) 1. Remove the P5 Spring. 2. Remove the screw 1. 3. Unlock the 2 supports 2 and remove the Cassette Opener. 4. Remove the Pinch Roller Ass'y, Pinch Roller Lever and P5 Arm Ass'y.
1
P5 Spring
2
(2) A/C Head
1
A/C Head Base
Fig. 2-13-A
2
Cassette Opener
2
Spring Position
Fig. 2-13-B
Main Chassis
Fig. 2-12-A
The FE Head is not installed on the Video Cassette Player.
Fig. 2-14
B2-3
DISASSEMBLY INSTRUCTIONS
2-15: AHC ASS'Y/CYLINDER UNIT ASS'Y (Refer to Fig. 2-15) 1. Unlock the support 1 and remove the AHC Ass'y. 2. Remove the 3 screws 2. 3. Remove the Cylinder Unit Ass'y. NOTE When you install the Cylinder Unit Ass'y, tighten the screws from (1) to (3) in order while pulling the Ass'y toward the left front direction.
2
(3) AHC Ass'y Pinch Roller Cam Link Lever Spacer E-Ring Main Cam
1
Middle Gear
2 3
Joint Gear P5 Cam
Fig. 2-17-A
Cylinder Unit Ass'y
2
(1)
NOTE When you install the Pinch Roller Cam, P5 Cam and Main Cam, align each marker. (Refer to Fig. 2-17-B)
Pinch Roller Cam
2
(2)
P5 Cam
Fig. 2-15
Marker Main Cam
2-16: CAPSTAN DD UNIT (Refer to Fig. 2-16) 1. Remove the Capstan Belt. 2. Remove the 3 screws 1. 3. Remove the Capstan DD Unit. Fig. 2-17-B
Capstan Belt Capstan DD Unit
2-18: CLUTCH ASS'Y (Refer to Fig. 2-18) 1. Remove the Polyslider Washer 1. 2. Remove the Clutch Ass'y, Ring Spring, Ring Clutch, Gear Clutch and Polyslider Washer 2. NOTE When you install the Clutch Ass'y, oil the shaft (KYODO OIL Slidas #150).
1 1
Screw Torque: 5 0.5kgfcm
1 1
Fig. 2-16
Clutch Ass'y
2-17: MIDDLE GEAR/MAIN CAM (Refer to Fig. 2-17-A) 1. Remove the Polyslider Washer 1, then remove the Middle Gear. 2. Remove the E-Ring, then remove the Main Cam, Link Lever Spacer and P5 Cam. 3. Remove the Polyslider Washer 2, then remove the Pinch Roller Cam. 4. Remove the Polyslider Washer 3, then remove the Joint Gear.
Ring Spring Ring Clutch
Gear Clutch
App. 5mm
Fig. 2-18
B2-4
DISASSEMBLY INSTRUCTIONS
2-19: LOADING GEAR S/T ASS'Y (Refer to Fig. 2-19-A) 1. Remove the E-Ring 1 and remove the Main Loading Gear. 2. Remove the Capstan Brake Spring. 3. Slide the Main Rod and remove the Capstan Brake Arm Ass'y. 4. Remove the Main Rod. 5. Remove the Tension Lever. 6. Unlock the 2 supports 2 and remove the Clutch Lever. 7. Remove the screw 3. 8. Remove the LED Reflector. 9. Remove the Loading Arm S Ass'y and Loading Arm T Ass'y. 10. Remove the Loading Gear S and Loading Gear T. 11. Remove the Loading Gear Spring.
Capstan Brake Spring Capstan Brake Arm Ass'y S-S Brake Arm
2-20: INCLINED S/T ASS'Y (Refer to Fig. 2-20) 1. Unlock the support 1 and remove the P4 Cover. 2. Remove the S-S Brake Spring. 3. Unlock the support 2 and remove the Loading Gear Holder. 4. Remove the S-S Brake Arm. 5. Remove the Inclined S. 6. Remove the Inclined T. 7. Remove the 2 screws 3, then remove the Guide Roller. NOTE Do not touch the roller of Guide Roller.
2
Guide Roller S-S Brake Spring
1 3
Main Loading Gear Main Rod Inclined S Guide Roller
3
Tension Lever Clutch Lever Loading Gear T Inclined T
P4 Cover
2 2
LED Reflector
Loading Gear Spring Loading Arm T Ass'y Loading Gear S Loading Gear Spring Screw Torque: 0.7 0.2kgfcm
Fig. 2-20
Fig. 2-19-A NOTE When you install the Loading Arm S Ass'y, Loading Arm T Ass'y and Main Loading Gear, align each marker. (Refer to Fig. 2-19-B)
Marker
Marker
Fig. 2-19-B
B2-5
DISASSEMBLY INSTRUCTIONS
3. REMOVAL OF ANODE CAP
Read the following NOTED items before starting work. * After turning the power off there might still be a potential voltage that is very dangerous. When removing the Anode Cap, make sure to discharge the Anode Cap's potential voltage. * Do not use pliers to loosen or tighten the Anode Cap terminal, this may cause the spring to be damaged. REMOVAL 1. Follow the steps as follows to discharge the Anode Cap. (Refer to Fig. 3-1.) Connect one end of an Alligator Clip to the metal part of a flat-blade screwdriver and the other end to ground. While holding the plastic part of the insulated Screwdriver, touch the support of the Anode with the tip of the Screwdriver. A cracking noise will be heard as the voltage is discharged. Location of Anode Cap 3. After one side is removed, pull in the opposite direction to remove the other. NOTE Take care not to damage the Rubber Cap. INSTALLATION 1. Clean the spot where the cap was located with a small amount of alcohol. (Refer to Fig. 3-3.)
Fig. 3-3 GND on the CRT NOTE Confirm that there is no dirt, dust, etc. at the spot where the cap was located. 2. Arrange the wire of the Anode Cap and make sure the wire is not twisted. 3. Turn over the Rubber Cap. (Refer to Fig. 3-4.)
Screwdriver
Fig. 3-1
Fig. 3-4 4. Insert one end of the Anode Support into the anode button, then the other as shown in Fig. 3-5.
2. Flip up the sides of the Rubber Cap in the direction of the arrow and remove one side of the support. (Refer to Fig. 3-2.) Rubber Cap
CRT
5. Confirm that the Support is securely connected. 6. Put on the Rubber Cap without moving any parts.
B3-1
KEY TO ABBREVIATIONS
A A/C ACC AE AFC AFT AFT DET AGC AMP ANT A.PB APC ASS'Y AT AUTO A/V B BGP BOT BPF BRAKE SOL BUFF B/W C C CASE CAP CARR CH CLK CLOCK (SY-SE) COMB CONV CPM CTL CYL CYL-M CYL SENS D DATA (SY-CE) dB DC DD Unit DEMOD DET DEV E E EF EMPH ENC ENV EOT EQ EXT F F FBC FE FF FG FL SW FM FSC FWD G GEN GND H H.P.F : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : Audio/Control Automatic Color Control Audio Erase Automatic Frequency Control Automatic Fine Tuning Automatic Fine Tuning Detect Automatic Gain Control Amplifier Antenna Audio Playback Automatic Phase Control Assembly All Time Automatic Audio/Video Burst Gate Pulse Beginning of Tape Bandpass Filter Brake Solenoid Buffer Black and White Capacitance, Collector Cassette Capstan Carrier Channel Clock Clock (Syscon to Servo) Combination, Comb Filter Converter Capstan Motor Control Cylinder Cylinder-Motor Cylinder-Sensor Data (Syscon to Servo) Decibel Direct Current Direct Drive Motor Unit Demodulator Detector Deviation Emitter Emitter Follower Emphasis Encoder Envelope End of Tape Equalizer External Fuse Feed Back Clamp Full Erase Fast Forward, Flipflop Frequency Generator Front Loading Switch Frequency Modulation Frequency Sub Carrier Forward Generator Ground High Pass Filter I H.SW Hz IC IF IND INV KIL L LED LIMIT AMP LM, LDM LP L.P.F LUMI. M MAX MINI MIX MM MOD MPX MS SW NC NR OSC OPE PB PB CTL PB-C PB-Y PCB P. CON PD PG P-P R REC REC-C REC-Y REEL BRK REEL S REF REG REW REV, RVS RF RMC RY S. CLK S. COM S. DATA SEG SEL SENS SER SI SIF SO SOL SP STB SW : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : Head Switch Hertz Integrated Circuit Intermediate Frequency Indicator Inverter Killer Left Light Emitting Diode Limiter Amplifier Loading Motor Long Play Low Pass Filter Luminance Motor Maximum Minimum Mixer, mixing Monostable Multivibrator Modulator, Modulation Multiplexer, Multiplex Mecha State Switch Non Connection Noise Reduction Oscillator Operation Playback Playback Control Playback-Chrominance Playback-Luminance Printed Circuit Board Power Control Phase Detector Pulse Generator Peak-to Peak Right Recording Recording-Chrominance Recording-Luminance Reel Brake Reel Sensor Reference Regulated, Regulator Rewind Reverse Radio Frequency Remote Control Relay Serial Clock Sensor Common Serial Data Segment Select, Selector Sensor Search Mode Serial Input Sound Intermediate Frequency Serial Output Solenoid Standard Play Serial Strobe Switch
K L
N O P
C1-1
KEY TO ABBREVIATIONS
S SYNC SYNC SEP T TR TRAC TRICK PB TP U UNREG V V VCO VIF VP V.PB VR V.REC VSF VSR VSS V-SYNC VT X X'TAL Y Y/C : : : : : : : : : : : : : : : : : : : : : Synchronization Sync Separator, Separation Transistor Tracking Trick Playback Test Point Unregulated Volt Voltage Controlled Oscillator Video Intermediate Frequency Vertical Pulse, Voltage Display Video Playback Variable Resistor Video Recording Visual Search Fast Forward Visual Search Rewind Voltage Super Source Vertical-Synchronization Voltage Tuning Crystal Luminance/Chrominance
C1-2
Method Press the ATR button on the remote control for more than 2 seconds during PLAY. Make the short circuit between the test point of SERVICE and the GND.
Operations Adjusting of the Tracking to the center position. Refer to the "MECHANICAL ADJUSTMENT" (GUIDE ROLLER) and "ELECTRICAL ADJUSTMENT" (PG SHIFTER). The EOT/BOT/Reel sensor do not work at this moment. Refer to the "PREPARATION FOR SERVICING"
C2-1
500 hours
1,000 hours
1,500 hours
2,000 hours
3,000 hours
Notes
INIT
00
83
Initial setting content of MEMORY IC. POWER ON total hours. PLAY/REC total hours.
(16 x 16 x 16 x thousands digit value) + (16 x 16 x hundreds digit value) + (16 x tens digit value) + (ones digit value)
C3-1
Cylinder Head
C3-2
Table 1 1. Enter DATA SET mode by setting VOLUME to minimum. 2. While holding down VOLUME button on front cabinet, press key 6 on remote control simultaneously. 3. ADDRESS and DATA should appear as FIG 1.
ADDRESS DATA
INIT
00
83
C4-1
JG162C Cable (10 Pins) Parts No. SJ-G16-2C0-000 JG162D Cable (11 Pins) Parts No. SJ-G16-2D0-000 JG162Y Cable (5 Pins) Parts No. SJ-G16-2Y0-000
Tentelometer
Part No. JG001 JG001A JG001T JG001B JG001I JG001S JG002B JG002E JG002F JG005 JG153 JG022/JG024A JG100A JG154 JG162C/JG162D JG162Y Stair Steps, 7KHz (For 2 heads model) Color Bar, 1KHz (For 2 heads model) X Value Adjustment (For 2 heads model) Stair Steps, 7KHz (For 4 heads model) Color Bar, 1KHz (For 4 heads model) X Value Adjustment (For 4 heads model)
Remarks
VSR Torque, Brake Torque (S Reel/T Reel Ass'y) Brake Torque (T Reel Ass'y) VSR Torque, Brake Torque (S Reel) Guide Roller Adjustment X Value Adjustment Reel Disk Height Adjustment Playback Torque, Back Tension Torque During Playback Used to connect the test point of SERVICE and GROUND Used to connect the Syscon PCB and Main PCB Used to connect the Syscon PCB and CRT PCB
C5-1
CP820
CP810 JG162D
TP1001
CP354
C5-2
L503 (2 Pin)
Main PCB
C5-3
TTV-N1
CH-1B(4) *2
NTSC, Stairsteps, NTSC, Stairsteps, Head ACE Azimuth ADJ. CH-1B(1) 7kHz, SP 7kHz, SP
TTV-N12
(SCV-1998)
CH-1B(4)
TTV-N7A
NTSC, Stairsteps, NTSC, Color, No 1kHz, SP, HiFi CH-1B(3) sound SP, HiFi 400Hz 400Hz
TTV-P1
CH-2(2) *3
Switching position ADJ. PB-Y Level/General electrical ADJ. Head ACE Height/Tilt ADJ.
CH-2(4)
Switching position. (LP Model) FM Envelope ADJ. (LP Model) X-Value ADJ. (LP Model)
CH-2(1)
Head ACE Azimuth ADJ. FM Envelope ADJ. (SP Model) X-Value ADJ. (SP Model)
TTV-P7
PAL, Stairsteps, 1kHZ, SP, HiFi, 1kHz PAL, Color, 400Hz, SP, HiFi 1kHz
CH-2(3)
TTV-P16
No Changed.
FM Filter ADJ.
*1. Described in the order of color format. Video signal. Linear audio. Tape speed and Hi-Fi audio. *2. Use CH-1B (1) - (3) with models used exclusively in the SP mode. *3. Use CH-2 (3) and (4) when it is necessary to observe the chroma signal.
C6-1
MECHANICAL ADJUSTMENTS
1. CONFIRMATION AND ADJUSTMENT
Read the following NOTES before starting work. Place an object which weighs between 450g~500g on the Cassette Tape to keep it steady when you want to make the tape run without the Cassette Holder. (Do not place an object which weighs over 500g.) When you activate the deck without the Cassette Holder, short circuit between TP1001 and GND. (Refer to ELECTRICAL ADJUSTMENT PARTS LOCATION GUIDE) In this condition the BOT/EOT/Reel Sensor will not function. 1-1: CONFIRMATION AND ADJUSTMENT OF REEL DISK HEIGHT 1. Turn on the power and set to the STOP mode. 2. Set the master plane (JG022) and reel disk height adjustment jig (JG024A) on the mechanism framework, taking care not to scratch the drum, as shown in Fig. 11-A. 3. Confirm that "A" of the reel disk is lower than "B" of the reel disk height adjustment jig (JG024A) , and is higher than "C". If it is not enough height, adjust to 10(+0.2, -0) mm with the height adjustment washer. 4. Adjust the other reel in the same way.
Master Plane (JG022)
1-2: CONFIRMATION AND ADJUSTMENT OF TENSION POST POSITION 1. Set to the PLAY mode. 2. Adjust the Tension Adjust until the edge of the Tension Arm is positioning within 0.5mm range from the standard line center of Main Chassis. After this adjustment, confirm that the cut position is located in "A" area as shown in Fig. 1-2-B. If it is located in "B" area, adjust again. 3. While turning the S Reel clockwise, confirm that the edge of the Tension Arm is located in the position described above.
Standard line of Main Chassis
Tension Arm 0.5mm (Adjusting range) Standard line center of Main Chassis Tension Adjust
Fig. 1-2-A
Fig. 1-2-B 1-3: CONFIRMATION OF PLAYBACK TORQUE AND BACK TENSION TORQUE DURING PLAYBACK Fig. 1-1-A
Reel Disk Height Adjustment Jig (JG024A)
1. Load a video tape (T-120) recorded in standard speed mode. Set the unit to the PLAY mode. 2. Install the tentelometer as shown in Fig. 1-3. Confirm that the meter indicates 20 2gf in the beginning of playback. USING A CASSETTE TYPE TORQUE TAPE (JG100A) 1. After confirmation and adjustment of Tension Post position (Refer to item 1-2), load the cassette type torque tape (JG100A) and set to the PLAY mode. 2. Confirm that the right meter of the torque tape indicates 70~110gfcm during playback in SP mode. 3. Confirm that the left meter of the torque tape indicates 25~40gfcm during playback in SP mode.
Tentelometer
Reel Disk
(B)
Video Tape
Fig. 1-1-B
P1 Post
Guide Roller
Fig. 1-3
D1-1
MECHANICAL ADJUSTMENTS
1-4: CONFIRMATION OF VSR TORQUE 1. Operate within 4~5 seconds after the reel disk begins to turn. 2. Install the Torque Gauge (JG002F) and Adapter (JG002B) on the S Reel. Set to the Rewind mode. (Refer to Fig.1-4) 3. Then, confirm that it indicates 120~180gfcm. NOTE Install the Torque Gauge on the reel disk firmly. Press the REW button to turn the reel disk. 1-5: CONFIRMATION OF REEL BRAKE TORQUE (S Reel Brake) (Refer to Fig. 1-4) 1. Set to the STOP mode. 2. Move the Idler Ass'y from the S Reel. 3. Install the Torque Gauge (JG002F) and Adapter (JG002B) on the S Reel. Turn the Torque Gauge (JG002F) clockwise. 4. Then, confirm that it indicates 70~100gfcm. (T Reel Brake) (Refer to Fig. 1-4) 1. Set to the STOP mode. 2. Move the Idler Ass'y from the T Reel Ass'y. 3. Install the Torque Gauge (JG002E) and Adapter (JG002B) on the T reel. Turn the Torque Gauge (JG002E) counterclockwise. 4. Then, confirm that it indicates 35~60gfcm.
Torque Gauge/Adapter (JG002F/JG002B)
CH-2 Track
S Reel Envelope
T Reel Ass'y
Fig. 1-4
NOTE If the torque is out of the range, replace the following parts. Check item 1-4 1-5 Replacement Part Idler Ass'y/Clutch Ass'y T Brake Spring/Tension Spring
Max
Fig. 2-1-A
Entrance
Exit
Max
A:B=3:2
Fig. 2-1-B
D1-2
MECHANICAL ADJUSTMENTS
2-2: CONFIRMATION AND ADJUSTMENT OF AUDIO/ CONTROL HEAD When the Tape Running Mechanism does not work well, adjust the following items. 1. Playback the VHS Alignment Tape (JG001 or JG001B). (Refer to SERVICING FIXTURE AND TOOLS) 2. Confirm that the reflected picture of stamp mark is appeared on the tape prior to P4 Post as shown in Fig. 2-2-A. a) When the reflected picture is distorted, turn the screw 1 clockwise until the distortion is disappeared. b) When the reflected picture is not distorted, turn the screw 1 counterclockwise until little distortion is appeared, then adjust the a). 3. Turn the screw 2 to set the audio level to maximum. 4. Confirm that the bottom of the Audio/ Control Head and the bottom of the tape is shown in Fig. 2-2-C. c) When the height is not correct, turn the screw 3 to adjust the height. Then, adjust the 1~3 again.
Audio/Control Head Reflected picture of Stamp Mark P4 Post
2-3: TAPE RUNNING ADJUSTMENT (X VALUE ADJUSTMENT) 1. Confirm and adjust the height of the Reel Disk. (Refer to item 1-1) 2. Confirm and adjust the position of the Tension Post. (Refer to item 1-2) 3. Adjust the Guide Roller. (Refer to item 2-1) 4. Confirm and adjust the Audio/Control Head. (Refer to item 2-2) 5. Connect CH-1 of the oscilloscope to TP4001, CH-2 to TP1002 and CH-3 to HOT side of Audio Out Jack. 6. Playback the VHS Alignment Tape (JG001S or JG001T). (Refer to SERVICING FIXTURE AND TOOLS) 7. Press and hold the TRACKING-AUTO button on the remote control more than 2 seconds to set tracking to center. 8. Set the X Value adjustment driver (JG153) to the 4 of Fig. 2-2-B. Adjust X value so that the envelope waveform output becomes maximum. Check if the relation between Audio and Envelope waveform becomes (1) or (2) of Fig. 2-1-A.
Stamp Mark
Fig. 2-2-A
Audio/Control Head
2 4
Fig. 2-2-B
0.250.05mm
Fig. 2-2-C
D1-3
MECHANICAL ADJUSTMENTS
3. MECHANISM ADJUSTMENT PARTS LOCATION GUIDE
3 7 2 1 8
12
11
10
1. Tension Adjust 7. P4 Post 2. Tension Arm 8. T Brake Spring 3. Guide Roller 9. T Reel Ass'y 4. P1 Post 10. Idler Ass'y 5. Audio/Control Head 11. S-S Brake Spring 6. X value adjustment driver hole 12. S Reel
D1-4
ELECTRICAL ADJUSTMENTS
1. ADJUSTMENT PROCEDURE
Read and perform these adjustments when repairing the circuits or replacing electrical parts or PCB assemblies. CAUTION When replacing IC's or transistors, use only specified silicon grease (G746). (To prevent the damage to IC's and transistors.) On-Screen Display Adjustment 1. Unplug the AC plug for more than 5 seconds to set the clock to the non-setting state. Then, set the volume level to minimum. 2. Press the VOL. DOWN button on the set and the channel button (9) on the remote control simultaneously to display adjustment mode on the screen as shown in Fig. 1-1. NOTE Use the channel buttons (1-8) on the remote control to select the options shown in Fig. 1-1. Press the channel button (0) on the remote control to end the adjustments. 1. H/V 2. AKB 3. COLOR TEMP 4. PICTURE 5. OTHERS 6. TEST PATTERN 7. STEREO/SAP 8. (VOL TEST) 0. END "The adjustment items 3, 6, 7 and 8 are not used for this model." Fig. 1-1
6.5H 6.5H CH-1 CH-2
Fig. 2-1-A
CH-2
CH-1
Fig. 2-1-B 2-2: VCO FREERUN 1. Place the set with Aging Test for more than 15 minutes. 2. Receive the VHF HIGH. 3. Disconnect the Antenna while receiving the VHF HIGH and set to the Noise screen. 4. Once turn off the Power and turn on the Power again. 5. Approxi. 3 seconds later, input the Antenna again. 6. Connect the digital voltmeter to TP601. 7. Adjust the L610 until the digital voltmeter is 3.1 0.05V. 2-3: RF AGC 1. Receive the VHF HIGH (70dB). 2. Connect the digital voltmeter between the pin 5 of CP603 and the pin 1 (GND) of CP603. 3. Activate the adjustment mode display of Fig. 1-1 and press the channel button (5) on the remote control. The Fig. 2-2 appears on the display. 4. Press the channel button (1) on the remote control. 5. Press the VOL. UP/DOWN button on the remote control until the digital voltmeter is 2.3 0.05V. 1. RF AGC DELAY 2. VIDEO LEVEL 3. FM LEVEL 4. OSD H 5. CUT OFF 6. 7. 8. 0. RETURN "The adjustment items 2 and 3 are not used for this model." Fig. 2-2
D2-1
ELECTRICAL ADJUSTMENTS
(TV SECTION)
2-4: CONSTANT VOLTAGE 1. Connect the digital voltmeter to TP401. 2. Set condition is AV MODE without signal. 3. Adjust the VR502 until the DC voltage is 135 0.5V. 2-5: OSD HORIZONTAL 1. Using the remote control, set the brightness and contrast to normal position. 2. Activate the adjustment mode display of Fig. 1-1 and press the channel button (5) on the remote control. The Fig. 2-2 appears on the display. 3. Press the channel button (4) on the remote control. 4. Press the VOL. UP/DOWN button on the remote control until the difference of A and B becomes minimum. (Refer to Fig. 2-3) 2-7: VERTICAL SIZE NOTE: Adjust after performing adjustments in section 2-6. 1. Receive the cross hatch signal from the Pattern Generator. 2. Using the remote control, set the brightness and contrast to normal position. 3. Activate the adjustment mode display of Fig. 1-1 and press the channel button (1) on the remote control. The Fig. 2-4 appears on the display. 4. Press the channel button (3) on the remote control. 5. Press the VOL. UP/DOWN button on the remote control until the rectangle on the center of the screen becomes square. 6. Receive a broadcast and check if the picture is normal. 2-8: VERTICAL LINEARITY NOTE: Adjust after performing adjustments in section 2-7. [ TV ] 1. Receive the cross hatch signal from the Pattern Generator. 2. Using the remote control, set the brightness and contrast to normal position. 3. Activate the adjustment mode display of Fig. 1-1 and press the channel button (1) on the remote control. The Fig. 2-4 appears on the display. 4. Press the channel button (5) on the remote control. 5. Press the VOL. UP/DOWN button on the remote control until the SHIFT quantity of the OVER SCAN on upside and downside becomes minimum. 2-9: VERTICAL POSITION NOTE: Adjust after performing adjustments in section 2-8. 1. Receive the center cross signal from the Pattern Generator. 2. Using the remote control, set the brightness and contrast to normal position. 3. Activate the adjustment mode display of Fig. 1-1 and press the channel button (1) on the remote control. The Fig. 2-4 appears on the display. 4. Press the channel button (4) on the remote control. 5. Press the VOL. UP/DOWN button on the remote control until the horizontal line becomes fit to the notch of the shadow mask. 2-10: FOCUS 1. Receive a broadcast. 2. Turn the Focus Volume fully counterclockwise once. 3. Adjust the Focus Volume until picture is distinct. 2-11: CUT OFF 0. RETURN 1. Place the set with Aging Test for more than 15 minutes. 2. Set condition is AV MODE without signal. 3. Using the remote control, set the brightness and contrast to normal position. 4. Activate the adjustment mode display of Fig. 1-1 and press the channel button (5) on the remote control. The Fig. 2-2 appears on the display. 5. Press the channel button (5) on the remote control. 6. Adjust the Screen Volume until a dim raster is obtained.
OSD H
Fig. 2-3
1. Receive the center cross signal from the Pattern Generator. 2. Using the remote control, set the brightness and contrast to normal position. 3. Activate the adjustment mode display of Fig. 1-1 and press the channel button (1) on the remote control. The Fig. 2-4 appears on the display. 4. Press the channel button (1) on the remote control. 5. Press the VOL. UP/DOWN button on the remote control until the right and left screen size of the vertical line becomes the same. 1. H. PHASE 2. H. BLK 3. V. SIZE 4. V. POSI 5. V. LIN 6. V. SC 7. V. COMP 8. (H FREQ)
"The adjustment item 8 is not used for this model." Fig. 2-4
D2-2
ELECTRICAL ADJUSTMENTS
2-12: SUB BRIGHTNESS 1. Receive the black pattern*. (RF Input) 2. Using the remote control, set the brightness and contrast to normal position. 3. Activate the adjustment mode display of Fig. 1-1 and press the channel button (4) on the remote control. The Fig. 2-5 appears on the display. 4. Press the channel button (1) on the remote control. 5. Press the VOL. UP/DOWN button on the remote control until the screen begin to shine. 6. Receive the black pattern*. (Audio Video Input) 7. Press the TV/VCR button on the remote control to set to the AV mode. Then perform the above adjustments 2~5. *The Black Pattern means the whole black raster signal. Select the "RASTER" of the pattern generator, set to the OFF position for each R, G and B. 1. BRIGHT 2. CONTRAST 3. COLOR 4. TINT 5. SHARPNESS 6. OSD CONT 7. 8. 2-14: SUB TINT 1. Receive the color bar pattern. (RF Input) 2. Using the remote control, set the brightness, contrast, color and tint to normal position. 3. Connect the synchro scope to TP803. 4. Activate the adjustment mode display of Fig. 1-1 and press the channel button (4) on the remote control. The Fig. 2-5 appears on the display. 5. Press the channel button (4) on the remote control. 6. Press the VOL. UP/DOWN button on the remote control until the section "A" becomes a straight line. (Refer to Fig. 2-7) 7. Receive the color bar pattern. (Audio Video Input) 8. Press the TV/VCR button on the remote control to set to the AV mode. Then perform the above adjustments 2~6.
0. RETURN
"A" Fig. 2-5 Fig. 2-7 2-15: SUB CONTRAST 1. Activate the adjustment mode display of Fig. 1-1 and press the channel button (4) on the remote control. The Fig. 2-5 appears on the display. 2. Press the channel button (2) on the remote control. 3. Press the VOL. UP/DOWN button on the remote control until the contrast step No. becomes "82" 4. Press the TV/VCR button on the remote control to set to the AV mode. 5. Activate the adjustment mode display of Fig. 1-1 and press the channel button (4) on the remote control. The Fig. 2-5 appears on the display. 6. Press the channel button (2) on the remote control. 7. Press the VOL. UP/DOWN button on the remote control until the contrast step No. becomes "97" 2-16: SUB SHARPNESS 1. Activate the adjustment mode display of Fig. 1-1 and press the channel button (4) on the remote control. The Fig. 2-5 appears on the display. 2. Press the channel button (5) on the remote control. 3. Check if the step No. of SHARPNESS is "24". 4. Press the TV/VCR button on the remote control to set to the AV mode. Then perform the above adjustments 1~3. 2-17: OSD CONTRAST 1. Using the remote control, set the brightness and contrast to normal position. 2. Activate the adjustment mode display of Fig. 1-1 and press the channel button (4) on the remote control. The Fig. 2-5 appears on the display. 3. Press the channel button (6) on the remote control. 4. Check if the step No. of OSD CONT. is "0". D2-3
2-13: SUB COLOR 1. Receive the color bar pattern. (RF Input) 2. Using the remote control, set the brightness, contrast, color and tint to normal position. 3. Connect the synchro scope to TP801. 4. Activate the adjustment mode display of Fig. 1-1 and press the channel button (4) on the remote control. The Fig. 2-5 appears on the display. 5. Press the channel button (3) on the remote control. 6. Adjust the VOLTS RANGE VARIABLE knob of the oscilloscope until the range between white 100% and 0% is set to 4 scales on the screen of the oscilloscope. 7. Press the VOL. UP/DOWN button on the remote control until the red color level is adjusted to 100 5% of the white level. (Refer to Fig. 2-6) 8. Receive the color bar pattern. (Audio Video Input) 9. Press the TV/VCR button on the remote control to set to the AV mode. Then perform the above adjustments 2~7. White 0% 0%
100%
ELECTRICAL ADJUSTMENTS
2-18: WHITE BALANCE NOTE: Adjust after performing adjustments in section 2-11. 1. Place the set with Aging Test for more than 15 minutes. 2. Receive the white 100% signal from the Pattern Generator. 3. Using the remote control, set the brightness and contrast to normal position. 4. Activate the adjustment mode display of Fig. 1-1 and press the channel button (2) on the remote control. The Fig. 2-8 appears on the display. 5. Perform channel button 2 through 7 on the remote control until the screen becomes white. 1. AKB AUTO 2. R.BIAS 3. G.BIAS 4. B.BIAS 5. R.DRIVE 6. G.DRIVE 7. B.DRIVE 8. AGC AUTO
0. RETURN
"The adjustment items 1 and 8 are not used for this model." Fig. 2-8 2-19: H. BLK 1. Activate the adjustment mode display of Fig. 1-1 and press the channel button (1) on the remote control. The Fig. 2-4 appears on the display. 2. Press the channel button (2) on the remote control. 3. Switch the R/L by using the ENTER button on the remote control and check if the H. BLK step No. becomes "R0, L0". 2-20: V. S-CORRECTION (V. SC) 1. Activate the adjustment mode display of Fig. 1-1 and press the channel button (1) on the remote control. The Fig. 2-4 appears on the display. 2. Press the channel button (6) on the remote control. 3. Check if the step No. of V. SC is "0". 2-21: V. COMP 1. Activate the adjustment mode display of Fig. 1-1 and press the channel button (1) on the remote control. The Fig. 2-4 appears on the display. 2. Press the channel button (7) on the remote control. 3. Check if the step No. of V. COMP is "7".
D2-4
ELECTRICAL ADJUSTMENTS
3. ELECTRICAL ADJUSTMENT PARTS LOCATION GUIDE (VCR SECTION)
TP1001
TP1002 TP4001
SYSCON PCB
D2-5
ELECTRICAL ADJUSTMENTS
(TV SECTION)
CRT PCB
VR502
TP401 T501
FB401
MAIN PCB
D2-6
ELECTRICAL ADJUSTMENTS
4. PURITY AND CONVERGENCE ADJUSTMENTS
NOTE 1. Turn the unit on and let it warm up for at least 30 minutes before performing the following adjustments. 2. Place the CRT surface facing east or west to reduce the terrestrial magnetism. 3. Turn ON the unit and demagnetize with a Degauss Coil. 4-1: STATIC CONVERGENCE (ROUGH ADJUSTMENT) 1. Tighten the screw for the magnet. Refer to the adjusted CRT for the position. (Refer to Fig. 4-1) If the deflection yoke and magnet are in one body, untighten the screw for the body. 2. Receive the green raster pattern from the color bar generator. 3. Slide the deflection yoke until it touches the funnel side of the CRT. 4. Adjust center of screen to green, with red and blue on the sides, using the pair of purity magnets. 5. Switch the color bar generator from the green raster pattern to the crosshatch pattern. 6. Combine red and blue of the 3 color crosshatch pattern on the center of the screen by adjusting the pair of 4 pole magnets. 7. Combine red/blue (magenta) and green by adjusting the pair of 6 pole magnets. 8. Adjust the crosshatch pattern to change to white by repeating steps 6 and 7. 4-2: PURITY NOTE Adjust after performing adjustments in section 4-1. 1. Receive the green raster pattern from color bar generator. 2. Adjust the pair of purity magnets to center the color on the screen. Adjust the pair of purity magnets so the color at the ends are equally wide. 3. Move the deflection yoke backward (to neck side) slowly, and stop it at the position when the whole screen is green. 4. Confirm red and blue colors. 5. Adjust the slant of the deflection yoke while watching the screen, then tighten the fixing screw. DEFLECTION YOKE DEFLECTION YOKE SCREW MAGNET SCREW 4-3: STATIC CONVERGENCE NOTE Adjust after performing adjustments in section 4-2. 1. Receive the crosshatch pattern from the color bar generator. 2. Combine red and blue of the 3 color crosshatch pattern on the center of the screen by adjusting the pair of 4 pole magnets. 3. Combine red/blue (magenta) and green by adjusting the pair of 6 pole magnets. 4-4: DYNAMIC CONVERGENCE NOTE Adjust after performing adjustments in section 4-3. 1. Adjust the differences around the screen by moving the deflection yoke upward/downward and right/left. (Refer to Fig. 4-2-a) 2. Insert three wedges between the deflection yoke and CRT funnel to fix the deflection yoke. (Refer to Fig. 4-2-b) RGB RGB
R G B
R G B RIGHT/LEFT SLANT
UPWARD/DOWNWARD SLANT
Fig. 4-2-a
WEDGE
WEDGE
D2-7
TROUBLESHOOTING GUIDE
(Television division)
( 1 ) that a power supply doesn't enter (In case that there isn't a normal tension for time to do standby CD810 every terminal)
NO
NO
Whether there is output for IC501 3rd pin or not ? YES Investigate T501.
NO
NO
Investigate T502.
AT6V is it normal ?
NO
Investigate IC505.
YES
AT5.6V is it normal ?
NO
Investigate IC502.
YES
P.CON 9V is it normal ?
NO
YES
AT 12V is it normal ?
NO
YES
NO E-1
TROUBLESHOOTING GUIDE
( 2 ) that a power supply doesn't enter (In case that there is a normal tension for time to do standby CD810 every terminal)
NO
NO
Is there 12MHz OSC for IC1001 38th pin and 39th pin or not ? YES
NO
Investigate X1001.
NO
NO
NO
NO
Investigate CRT.
E-2
TROUBLESHOOTING GUIDE
A voice isn't though an image appears
NO
Whether does a signal come to IC604 66th pin or not ? YES Investigate IC604 peripheral circuit.
NO
NO
Investigate IC604.
NO
NO
Investigate a speaker.
E-3
TROUBLESHOOTING GUIDE
A color doesn't adhere to it
NO
Investigate X604.
NO
Investigate IC604.
IC604 17th pin, 18th pin, and whether is wave form of 19th pin normal or not ? YES
NO
Investigate IC604.
E-4
TROUBLESHOOTING GUIDE
An image doesn't appear
NO
NO
Investigate IC604.
NO
Investigate IC4001.
R, G, B signal out from the 17th pin, the 18th pin and 19th pin ? YES
NO
E-5
TROUBLESHOOTING GUIDE
An only horizontal line appears
NO
NO
Whether does a vertical signal appear for IC604 26th pin or not ?
NO
Investigate IC604.
The wave form of the 62nd pin, the 63rd pin, the 64th pin, and also the 60th pin of IC1001 normal ? YES
NO
The wave form of the 58th pin, the 59th pin, and also the 56th pin of IC1001 is investigated. Q1016 and also Q1015 are investigated.
The wave form of the 17th pin, 18th pin and 19th pin of IC604 normal ?
NO
E-6
Yes
Yes
Check IC1001.
E-7
TROUBLESHOOTING GUIDE
NO PLAYBACK PICTURE
No
No
Yes
Yes
No
Yes
No
Yes
No
Replace IC4001.
Yes
No
Yes
No
Replace IC4001.
Yes
E-8
TROUBLESHOOTING GUIDE
NO COLOR DURING PLAYBACK
No
Yes
No
Yes
No
Replace IC4001.
Check TV Block.
E-9
TROUBLESHOOTING GUIDE
PLAYBACK PICTURE IS NOISY (EVEN AFTER CLEANING HEADS)
No
Yes
No
Yes
Is VIDEO waveform at pins 20 and 21 of IC4001 about 450mVp-p, and are there any noises ? Yes
No
Replace IC4001.
Is VIDEO waveform at pin 29 of IC4001 2V, and are there any noises ? Yes
No
Replace IC4001.
E-10
TROUBLESHOOTING GUIDE
NO COLOR DURING SELF RECORDING AND PLAYBACK
No
No
Replace IC4001.
E-11
TROUBLESHOOTING GUIDE
NO NORMAL AUDIO IN PLAYBACK MODE
No
Yes
No
Check AUDIO HEAD for debris or stains. Check the connector from AUDIO HEAD is fully inserted to CP4005. Replace IC4001.
Yes
No
Replace IC4001.
E-12
TROUBLESHOOTING GUIDE
CAPSTAN DD MOTOR NOT ROTATING
No
No
Yes
No
Replace IC1001.
No
E-13
TROUBLESHOOTING GUIDE
AUDIO CAN NOT BE RECORDED
No
No
Yes
L4003 is broken or shorted. Check peripheral circuit. Is there AUDIO signal at pins 78 or 80 of IC4001 ? No Check the circuit between audio out of Tuner and pins 78 or 80 of IC4001.
Yes
No
Yes
No
Replace IC4001.
Yes
E-14
TROUBLESHOOTING GUIDE
CASSETTE CAN BE LOADED BUT UNIT HAS NO FUNCTIONS
Yes
No
No
Check IC1001.
Yes
Yes
E-15
TROUBLESHOOTING GUIDE
RECORDING MECHANISM WORKS, BUT NO VIDEO RECORDED FROM INPUT JACK OR TUNER
No
Check the circuit from VIDEO input jack to IC4001 and from Tuner Pack to IC4001.
No
No
Replace IC1001.
Yes
Yes
Replace IC4001. Does VIDEO signal appear at pin 21 of IC4001 ? No Check the peripheral circuit of Q4009.
Yes
E-16
TROUBLESHOOTING GUIDE
NO E-E (NO VIDEO AND AUDIO FROM TUNER)
Yes
Replace J4201.
Do the following voltages appear on TU601, 30V at pin 9 and 5V at pin 7 ? Yes
No
No
Yes
No
No
Yes
No
Yes
E-17
TROUBLESHOOTING GUIDE
CYLINDER NOT ROTATING DURING PLAYBACK AND RECORDING
No
Yes
Yes
No
Replace IC1001.
E-18
TROUBLESHOOTING GUIDE
AUDIO SHAKES
Yes
No
No
In playback, is the voltage at pin 4 of CP1004 2.8V ? Is the voltage at No pin 4 of CP1004 3.3V when you stop the CAPSTAN DD MOTOR manually ? Yes
No
No
Replace IC1001.
Yes
E-19
TROUBLESHOOTING GUIDE
CASSETTE TAPE IS NOT ACCEPTED
When cassette is not inserted, is the voltage 1.6V at Emitter of Q102 and Q101 ? Yes
No
When a cassette is inserted, is the voltage between pins 3 and 4 of CP1006 12V ? No
Yes
No
No
Replace X1001.
Yes
Replace IC1001.
E-20
TROUBLESHOOTING GUIDE
WHEN INSERTING CASSETTE, IT EJECTS IMMEDIATELY
Does this same problem appear when using another cassette tape ? Yes
No
No
No
Yes
No
Yes
E-21
TROUBLESHOOTING GUIDE
FF/REW DO NOT WORK
When the FF (or REW) is pressed, does the voltage at pin 11 of IC1001 change to high (low in REW) ? Yes
No
When the FF (or REW) is pressed, does the FF (or REW) indicator appear on screen ? Yes
No
No
Yes
No
Yes
E-22
TROUBLESHOOTING GUIDE
TAPE LOADING IS OK, BUT UNLOADS IMMEDIATELY
No
No
Yes
No
No
Yes
No Does TP1002 feed HEAD SWITCHING PULSE signal ? 30 Hz Yes Does PG PULSE signal, 4.2Vp-p appear at pin 90 of IC1001 ? Yes
No
Replace IC1001.
Yes
E-23
TROUBLESHOOTING GUIDE
PLAYBACK PICTURE JITTERS VERTICALLY
No
Yes
By adjusting the manual tracking UP/DOWN buttons, will the noise disappear in the picture ? Yes
No
No
Yes
No
Adjust PG SHIFTER.
Yes
E-24
TROUBLESHOOTING GUIDE
PLAYBACK PICTURE JITTERS HORIZONTALLY
No
Yes
Is the voltage at pin 5 of CP1005 1.3V or When slowing CYLINDER, is the voltage about 5V ? Yes
No
Replace IC1001.
No
In auto tracking, is the voltage at pin 6 of IC1001 more than DC1.85V ? Yes
No
Does the CTL PULSE (about 2.0Vp-p) appear at pin 96 of IC1001 ? 2.0Vp-p Yes
No
Replace IC1001.
E-25
TROUBLESHOOTING GUIDE
WHEN PLAYBACK, FAST FORWARD OR REWIND MODE IS ACTIVATED, UNIT STOPS IMMEDIATELY
No
Yes
No
Yes
No
No
Replace IC1001.
E-26
IC DESCRIPTION
OEC7041A (IC1001)
Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 Pin Name MSSEN-A MSSEN-B EOT BOT HI-FI-ENV VIDEO-ENV AFT(MONI) AFT(REC) KEY A KEY B CAP-FWD CAP-LIMIT DUMMY-V.SYNC REMOCON-IN COLOR ROTARY HEAD.AMP.SW ENV-CMP-IN VIDEO-H.SW HI-FI-H.SW LDM-RVS LDM-FWD TRICK-PB-H MSSENS-CTL CAP-HI H PLAY LED EXT-MUTE VCR-POWER TV-POWER T-REC LED REC LED ON-TIMER LED OTPB LED AKB CTL RESET-L XC_IN(32kHz) XC_OUT(32kHz) VCC X-IN(12MHz) X-OUT(12MHz) VSS AV1 AV2 CLKSEL OSC-IN2 I/O I I I I I I I I I I O Capstan forward and backward command.(forward "L" output) O Switch the maximum output current of the Capstan Motor. O Virtual V Pulse output. I Receive the remote control signal. O Color Rotary Control output. O Switching output of Head Amp SW on 4 heads. I Comparison results input of Playback Envelope level ON SP/LP heads(4heads). O Output terminal of Head SW to Y/C/A and Head Amp. O Output terminal of audio Head SW to Y/C/A and Head Amp. O Output signal to control the rotation direction of the loading motor. O O Special effect playback.(CUE/REVIEW/STILL/SLOW etc) O MSSEN sensor LED. O Power of Capstan Motor select. O PLAY indication LED output. O Mute signal of external video mute. O VCR power output. O TV power output. O T-REC indication LED output. O REC indication LED output. O ON-TIMER indication LED output. O OTPB indication LED output. O "H" is output at the time of AKB white adjustment. I I O I O Ground. O Not used. O Not used. I I 5V Condenser connection for OSC-IN2. 5V Connect the main crystal.(10MHz) RESET will be done when the voltage goes to HIGH after the reset signal. Subclock pulse.(32kHz) Tape end sensor input signal. Tape start sensor input signal. Input terminal of HiFi RF envelope. Input terminal of video RF envelope. Input terminal of AFT. Not used. Main unit key input. Input terminal of mecha state sensor. DESCRIPTION
F1-1
IC DESCRIPTION
OEC7041A (IC1001)
Pin No. 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 Pin Name OSC-OUT2 NUB CM_ADV_VIDEO CM_ADV_AUDIO OSD-VSS TAB SW SERVICE SD-IN(MONI) OSD-VCC HLF VHOLD CVIN NUA H/C-SYNC V-SYNC OSD OUT1 CENTER LED B G R CAP FULL V-REC-ST-H IIC-CLK3 IIC-DATA3 SP-H IIC-DATA2 IIC-CLK1 IIC-DATA1 IIC-OFF JUST CLOCK AGC(REC) CAP-PWM DRUM-PWM E/V_MASK REEL-S REEL-T VCR_A_MUTE TV_A_MUTE FF/REW-L CA/MA_SEL POWER_FAIL_L CFG AMP-OUT CAP-FG I/O I I I I I I I Ground. Not used. Ground. Input terminal for judge the tape if it has TAB or not. Input terminal for Service Mode. Not used. 5V Condenser connection for HLF. Condenser connection for VHOLD. Composite Video input terminal. Ground. Input terminal for H-SYNC. Input terminal for V-SYNC. DESCRIPTION O Condenser connection for OSC-OUT2. I/O Not used.
O Blanking output terminal of OSD. O Tape end sensor LED. O Color signal blue output. O Color signal green output. O Color signal red output. O Output the HIGH during the acceleration force of capstan motor at SLOW mode. O On control of A/V recording (Whole width erase) circuit. O Not used. I/O Not used. O Output "H" terminal of Playback/Recording SP mode. I/O Terminal for I2C BUS communication. O CLOCK terminal for I2C BUS communication. I/O DATA terminal for I2C BUS communication. I I When input "L" the I2CBUS communication is stopped. Not used.
O Not used. O PWM putput of Capstan control. O PWM putput of Cylinder control. I I I Not used. Input terminal of reel sensor supply. Input terminal of reel sensor take up.
O Mute signal of audio mute.(VCR) O Mute signal of audio mute.(TV) O The output terminal of to that switches the frequency characteristic of CTL by the circuit bill outside. Input for the detection of power interruption. Input terminal for capstan rotation signal detection.
F1-2
IC DESCRIPTION
OEC7041A (IC1001)
Pin No. 88 89 90 91 92 93 94 95 96 97 98 99 100 100 Pin Name AMP-VSS DRUM-FG DRUM-PG AMP-VREFOUT AMP-VREFIN C CTLCTL+ AMP C CTL AMP-OUT AMP-VCC ANALOG VCC DEW(mono) STEREO SEL(HiFi) I/O I I I I Ground. Input terminal for drum rotation signal detection. Input terminal for DRUM PG signal detection. Condenser connection for AMP-VREFIN. Condenser connection for C. DESCRIPTION
I/O Input and output terminal of Control Head. I/O Input terminal of Control Head. I I Condenser connection for AMP C. 5V 5V Input terminal for the detection with the dew of the cylinder. Input terminal for the judgement of voice reception condition. O Output terminal for amp out.
The assignment for Pin 100 is varies according to the SET which is MONO or Hi-Fi. It is used for DEW terminal in MONO and STEREO SEL terminal in Hi-Fi.
F1-3
H. SW. P !8 PIN V-SYNC (E-E) %9 PIN REC CTL (REC) (7 PIN V-SYNC (TRICK PB) !3 PIN
CH 1
CH 2
F2-1
FWD : CAPSTAN FWD ROTATING DIRECTION RVS : CAPSTAN RVS ROTATING DIRECTION
UNLOADING STP3 VSR
PB
SLOW
: MECHANICAL MOVEMENT AND CAPSTAN ROTATING : MECHANICAL MOVEMENT (NO CAPSTAN ROTATING) F. SLOW PB/STP STP2 FF/REW
LIGHT GUARD LIGHT RECEIVING LIGHT GUARD LIGHT RECEIVING(H) LIGHT GUARD (L) LIGHT RECEIVING LIGHT GUARD
T BRAKE S BRAKE
FWD
TAPE LOADING (WHEN MSSEN A IS CHANGED FROM LIGHT GUARD TO LIGHT RECEIVING, CASSETTE IN WILL BE DETECTED)
FWD
RVS
(VCP) POWER OFF (VCR)
PB/STP
STP3
FWD
STP FF/FWD FF/REW FF/REW PB/STP
FF/REW
STP
POWER ON
PB
STP3
PB
FWD PB
F2-2
IC
1 2 1 1 7PIN LA7840
100PIN LA71170M-MPB
8PIN S-24C04BDP-LA
3 3PIN PST600H
1 9PIN AN7523
1 1 4 4PIN PQ09RD08 1 1 5 4PIN 80PIN 5PIN TLP621(D4-GR-LF2) LA76814BM-MPB STR-F6612 100PIN OEC7041A 1 8PIN BA6955AN
TRANSISTOR
K E C E CB B CE 2SD2599 B CE DTC114TSTP I O
ACE GP1S94L
2SC4217(D,E)-RAC 2SD2396(J,K)
DTC114ESTP
C 2SA1037AKT146R,S DTA114EKAT146 2SB1134R GP1S566 2SC2412KT146 R,S DTA124EKAT146 2SC4160-OEC-YAC1 SG-260 DTC114TKAT146 DTC114EKAT146 DTC124EKAT146 DTC143EKAT146
G-1
TV BLOCK DIAGRAM
R. SIGNAL G. SIGNAL B. SIGNAL COLOR SIGNAL
V. OUTPUT IC401 LA7840 THERMAL PROTECTION PUMP UP AMP VCC 2 5 6 7 Q405 H. DRIVE Q406 H. OUTPUT DY FB401
X604 3.579545MHz
CHROMA/IF IC604 LA76814BM Q608 BUFFER 47
ABL
52 54 66 73
8 CLMP CLMP
FBP PFC2 PHASE AHIFTER HOR OUT VER C/D VER SEP
VER RANP
11 33
4 2
9 1
DC VOL
PMP LIM
TU_AUDIO TU_VIDEO
Q602
75 69 67 56 BUS 9
TU601 1 4 5 11 SAW FILTER CF601 1 4 5
BPF
26
Q806 BLUE AMP Q804 RED AMP Q805 Q605 CUT OFF P.CON+9V
MICON/ POWER
SDA SCL
BUFFER
VIDEO DET
DEMO
DRIVE/CUT-OFF
19 17 18
10
77 RF AGC
IF AGC
CONTRAST BRIGHT
GREEN AMP
VD
HD OSD_BLK OSD_B OSD_G OSD_R AFT_M MICON/ POWER
CLAMP
AFT
PLL P2C
PEAKING CORING
14 13 12
8
3 1
F501 AC IN Q507
FEED BACK SW.
RY501 RELAY
D501~D504 RECTIFIER
9 8
3
AT 10V
T502 T501
Q503
+B 100V DRIVE
SP352 SPEAKER
3
6 4
14
AT 30V
5V POWER REG. IC502 KIA7806PI
100V DRIVE
SP351 SPEAKER
VR502
+B ADJ. Q506 5V SW. Q513 5V SW.
1
Q501 AT 5.6V AT +12V 100V SW.
1 2 2 7
J351 HEAD PHONE
12 9
1 1
3 3
16
H-1
X4001 3.579545MHz
Q4010 BUFFER
CP4001 6 SP CH1 (R) 5 SP COM 4 SP CH2 (L) CYL 3 EP/LP CH1 (R) 2 EP/LP COM 1 EP/LP-CH2 (L) 85 94 88 Q4004 BUFFER 90
REC FM AGC2
71 82
ENV DET R
72
P KIL DET
64
VXO
63
61
59
57
54
52 51
84
KIL R P
CLK 49 -IN 46
45
CLAMP Y.N.R
AFTER
COMP OUT
320FH VXO VCO PB_FM XO Sub AGC CONV P R REC BGA R P PB BGA AFTER C-LPF Main CONV BPF2 REC FM-AGC S-EQ P PB/EE AMP EQ AUTO BIAS LINE AMP REC AMP R PB_FM EQ ALC ALC DAT P R S N TH FM FM DEM DEM P
B_UP AMP ACC
Q4012 43
NL DE EMP BUFFER
R
YC SEP IN COMP IN
41
N.C.1
COMP SCL
SDA MICON/ POWER H.SW
PIC_CTL ANR
Y/C MIX
38 36 34
1/2
CTLCTL+
FBC
32 31 29 Q4011
BUFFER Y/C_VIDEO
3 4 11
MUTE
CLAMP
Q4001, Q4002
AUDIO PB SW
Y-VCC 19 21 20 16
SD_VIDEO
99
98
96
97 76 78 80
17
18
CP4005
6 5 HEAD AUDIO CONTROL 4 3 2 1 AUDIO PB AUDIO REC CTL+ CTLAE HEAD(-) AE HEAD(+) Q4005
Q4212
Q4007 AMP Q4009 BUFFER
Q4210 MUTE SW
EXT_MUTE
5 4
2 3
DRIVER
Q4013
SW
BUFFER
MICON/ POWER
V.REC_ST_H FRONT_VIDEO FRONT_AUDIO
FE HEAD
H-2
RECORD LUMINANCE SIGNAL PLAYBACK LUMINANCE SIGNAL RECORD COLOR SIGNAL PLAYBACK COLOR SIGNAL TUNER VIDEO SIGNAL AUDIO SIGNAL(REC) AUDIO SIGNAL (PB) TUNER AUDIO SIGNAL
2 1
3 4 50
TAB SW
RESET-L
34
3 OUT
TV
AT+5.6V
POWER_FAIL_L 1 2 1 4 3 4 3 1
MS_SEN A Q1009
85 39 38 36 35
P. CON 5V
MSSEN-A
X-OUT(12MHz) X-IN(12MHz)
2
MS_SEN B Q1003
MSSEN-B
XC-OUT(32KHz)
XC-IN(32MHz) ENV_CMP_IN
23
VIDEO 17
26 95 94 66 56 18
Q1002
SENSOR SW SENS LED
EXT-MUTE CTL+
P. CON 5V
1 2 1
79
REEL-S
CTL-
V-REC-ST-H
CVIN
80
REEL-T
VIDEO-H.SW
VIDEO_H SW
AT+12V
72 71 97 83 64 63 62 7 60 59 58
Q1018
TV VCR_POWER_H
BUFFER
27
VCR-POWER
R G B
CP1004 4 CTL CAPSTAN 5 VCO DD UNIT 6 FG 7 CAP.M F/R CP1005 1 CYL PG 3 CYL FG 5 CYL DRIVE
TV
Q1015
OSD_BLK
Q1016
INVERTER INVERTER
VD HD TV_POWER_H
MICRO MOTOR
P. CON 5V
LOADING MOTOR DRIVER IC1003 BA6955AN
BUFFER
POWER ON/OFF
REC/OTR
STOP/EJECT
PLAY
FF/CUE
REW/REV
10 Q4204 OS753 1 2 3
CONTROL LOGIC POWER SAVE 3 TSD 4 2 CP1006 2 BOT 3 LDM4 LDM+ CP1002 1 EOT 5 7 4 BOT REC LED 30 EOT REMOCON-IN 14 Q4205
TV POWER SW
CH DOWN
CH UP
VOL. UP
VOL. DOWN
PLAY BACK
AT+5.6V D791 D793 D792 D795 D796 D797 R. SIGNAL G.SIGNAL B. SIGNAL CAPSTAN AFC SIGNAL Q4202
REC LED SW
Q4206
20 21
LDM-RVS LDM-FWD
T-REC LED
29
T-REC LED SW
Q4207
DECK
25 32 31
PLAY LED SW
OTPB LED SW
Q4201
ON TIMER LED SW
CYLINDER AFC SIGNAL CYLINDER APC SIGNAL DEFLECTION SIGNAL TUNER VIDEO SIGNAL
H-3
OPERATION
SOLDER SIDE
W814 W805 W004 CD351_2 W813 R351 D792 C354 J701_1 D791 J351 W811 B701 C353
SW799
R763
SW798
SW795
SW791
R774
D797
W806
OS753 C752
SW797
R772
R775 W001
R776
R777
W816
R793
SW792
SW793
C781
SW751
DECK
SOLDER SIDE
CP101 CP102
Q101
Q102
I-1
(OPERATION PCB)
R761
R762
R763
270
D795 EM-553-F1T
D793 EQ-552-F1T
D791 EQ-552-F1T
R766 CD750 (CP354) CH2B026A REMOCON OUT 1 2 3 4 5 6 7 8 9 GND AT+5V POWER ON/OFF SW751 SKHVBED010 POWER ON L 0.001 B C781 OTPB/PLAY LED KEY A T-REC LED REC LED KEY B 0.001 B C779 ON TIMER LED PLAY LED R778 SW795 SKHVBED010 820 REC/OTR R771 SW791 SKHVBED010 1K STOP/EJECT R772 SW792 SKHVBED010 1.5K PLAY R773 SW793 SKHVBED010 2.7K FF/CUE R774 SW794 SKHVBED010 6.3V 220 KA 5.6K REW/REV 100P B 100 1/2W
3 GND 2 B+ 1 Vout
0.1 F C751
C755
C752
W804
D796 EM-553-F1T
OTPB LED
R793
R754
R755
270
270
270
OS753 PIC-28143TH5
D792 EQ-552-F1T
REC/OTR
PLAY LED
FROM/TO I/O
POWER LED
270
270
T-REC
10 11
6
R775 SW799 SKHVBED010 SW798 SKHVBED010 820 CH UP R776 SW796 SKHVBED010 1K VOL UP R777 SW797 SKHVBED010 1.5K VOL DOWN R780 SW750 SKHVBED010 2.7K PLAY BACK
CH DOWN
J351 HSJ2630-010070 1 NC R350 220 1/2W 5 4 3 C353 16V47 KA R351 220 1/2W 16V47 KA 2 6 7
W811
C354
D797 EQ-552-F1T
W812
4
W813
W806
W809
4 3 AUDIO L
1 E VIDEO
J701_1 JPJ3811-01-430
FROM/TO I/O CD351_2 (CP351) CH27086A 1 2 3 4 FRONT VIDEO IN GND FRONT AUDIO IN SOUND GND SOUND OUT SP OUT GND
5 6 7
AUDIO SIGNAL(REC) AUDIO SIGNAL(PB) RECORD LUMINANCE SIGNAL RECORD COLOR SIGNAL
NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
CAUTION: SINCE THESE PARTS MARKED BY CRITICAL FOR SAFETY,USE ONES DESCRIBED IN PARTS LIST ONLY
ARE
ATTENTION: LES PIECES REPAREES PAR UN ETANT DANGEREUSES AN POINT DE VUE SECURITE NUTILISER QUE CELLS DECRITES DANS LA NOMENCLATURE DES PIECES
PCB030 TEXA19
I-2
(DECK PCB)
S105
S106
S101
S102
S103
S104
FROM/TO MICON CP101 52044-0445 4 3 2 1 LDM+ LDMBOT VCC FROM/TO MICON CP102 173979-2 2 1 VCC EOT
PCB550 VE8851
CAUTION: SINCE THESE PARTS MARKED BY CRITICAL FOR SAFETY,USE ONES DESCRIBED IN PARTS LIST ONLY
ARE
ATTENTION: LES PIECES REPAREES PAR UN ETANT DANGEREUSES AN POINT DE VUE SECURITE NUTILISER QUE CELLS DECRITES DANS LA NOMENCLATURE DES PIECES
NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
I-3
R1039
R1018
R1064
Q1023
C1072 R1075 C1014 R1006 R1051 R1049 R1002 C1048 C1041 C1046 C1047 C1017 C1049 C1050 C1026 C1040 C1090 C1074 C1068 31 R1032 51 R1019 R1066 R1046 Q1024 1
IC 10 01
R1047
Q1002 C1088 Q4202 C1085_1 Q4201 Q4206 Q1017 Q1018 R4204 Q4207 Q4205
R1011 C1005 C4066 C4065 R1033 C4091 C4084 R4052 Q4010 C4095 C4082 R4048 C4047 C4024 R4040 R4019 C4020 C4042 C4034 C4033 C4094 C4097 C4054 C4069 C4038 C4029 R4027 R4024 51 C4079 C4061 C4056 C4060 C4059 Q4012 R4056 C4074 31 R1034 C1038 C4064 R4055 R4053 C4057
81
Q1004
C1034
R1017
C1019 R1012
C1007
R4036 R1070
R4028
I-4
C4204 W872
R4046
Q4009
Q4007
R4049 R4050 C4052 1 R4021 R4010 R4030 C4030 C4018 C4017 C4043 R4043 R4018 C4022 C4031 R4004 R4003 R4060 R4059 Q4004 C4077 R4045 R4042 C4044 R4038 C4036 C4037
C4049 R4051
R4041
Q4013
R4039 C4045
C4206
C1070
C4207
Q4204
R4064
C4005 R4058
Q4003
R4001
R631
W865
W863 R624 R627 R686 C631 R669 C4083 C4001 R351 R353 R618 W823 Q352 R4005 C4002 C1053 C1073 C1044_1 R1057 Q1016 R1058 C1055 R4203 R642 R648 R637 C665 R645 R646 R1060 C685 R621 C675 Q602 R4213 R4212 R4244 W980 C4210 C4205 C642 C630 64 C615 C670 R667 C669 W828 R654 R639 C644 C671 Q608 R625 R636 R635 C609 C614 C1078 R1061 W819 R1062 C1077 C622 R617
R1056
Q1015 R647 R649 R651 R601 R641 25 C620 R653 C649 W864 R620 C648 41
IC 60 4
Q1010
C662 R603
C607 C641 R1076 C616 Q1006 C687 R606 C657 R605 C604
R634
R1065
R612 R611 R623 W188 C658 C612 R4238 Q4212 R4236 C613
C647 R619
Q607
W133
CP352
RISK
OF FIRE
- REPLACE
AS MARKED.
C661 IC601
C683
CP351 L615
W083
W038
W200
CP601
TP1001
D622 W080 W032 L4005 W847 W030 W091 W089 C4023 W090 W047 L4011 L4015 W045 W077 C4078 W078 C1037
R4061
C4007
W088
L4014
R4067
W141 CP4001 R358 L4001 W137 W136 C4012 W201 R4007 R652 W134
W086
W202
C4051
C359_1
C4016
C4015
W177
C4055
W178
C352
W832 CD604
S801X W184
HS351
D605
R1016
R616
Q4005
C4025 C4048
C4063
D4004
C618
C4073
R4031
C4067
D1003
W182 D601
R4074
W181
Q4002
W868 C4071
L4003
L4004
W052
C4076
C4035 Q4006
W009
W094
C4003
W097
W098
C646
W049
D4001
C645 C611
C617 C624
X1002
C640
W157
TP4201
W160
W164
W158
TP601
W154
C621
C623 CF601
W153
W105
W199
L611
W198
W100
W099
Q1011
B602
W029 W076
C1020
R1079
Q1003
Q1
C601
L604
W058 C1018
00
R4239
R1087
W172
TU601 W194
L605
S801Y
R1050
W060
C355_2
W186 C605
W829
R1010
R1005
C1043
W173 D1001
W126
W024
W025
C1042
CP1006
IC1003 C1001 R1069 D4202 W074 W168 C1004 W122 W125 D4201 W822
W191
R1068
W190
L4205 CP353
I-5
TP1002 CP1002 TP4001 CC001 R4201 R4025
CP4
004
R4020
W037
W036
W035
R4029
SW1001
L4012
L4009
C1063
W003 W002
L4006
X4001
R4044
W833
C4041
W147
W007
W006
C4027
W085
W084
W854
C4039
C4046
C4050
C4053
W016
C4058
C634 C659
W015 C4070 W810 W054 W839 W840 W841 W051 W013 W012 W011 W050 W010 R1040 W008 W022 D1017 W053
C4062
W150
C4028
C643 C626
W014
L4007
C4068
C4040
C4006 W118
W815 W092
L1001 W048
W096
W093
W119
X1001
0 Q1
J4201 C4211
W073
R1001
05
R4063
R4062
R4035
R1053 W109
CP4005 W161
W110 W114
W113 W111
C1021
W112
W021
W163
C1058 C1056
W103
W803 C1032
CP
10
04
W018
W028
D1006
W027
C1015
D1007
R4032
D1005
D1014
W023
CC002
R1039
C1056
D1006
C1003_1
W002
W007
W003
W013
W022
W015
C1058
C1072
R1075
R1079
R1050
Q1002
Q1003 R1087
W014
W012
W010
C1063 IC1002
D1017
TP1001 W016
C1088
01 10 Q
W009
0 Q1
05
Q4201
W020
R1002
C1085_1 W076 W803 R1047 W018 C1049 C1050 X1002 C1017 C1074 C1068 W073 W029
W873
W069
L1001
W072
W055
CP1002
W050
Q1017 Q1018
W037
W810
Q1024
W043
W057
W813
W042
R4201
W047
W032
C4098
C4046
R4025
R1011 C1005 R4061 L4011 L4009 C4066 C4065 W045 C4038 L4014 R4048 C4047 C4039 R4040 C4050 C4084 R4052 C4053 Q4010 C4062 C4063 R4056 C4061 C4055 C4060 C4056 C4034 C4033 C4094 C4074 C4058 W030 R4067 C4024 W847 W077 C4097 C4078 W078 R4044 L4006 C4042 W084 W085 C4079 X4001 R4019 C4020 C4041 C4091 W035 W036 R4029 C4029 W833 W200 R4020 W083 TP4001 C4070 R1033 D4004 R1016 D1003 W038 C4095 C4082 C4069 C1038
W059
IC 10 01
81
R1031 C1035
C1031 W052 C1071 W048 C1082 W049 R1034 R4074 B4003 R1059 W096 R1055 W097 C1006 R661
C1034
C1089 Q1014 C1025 C1027 W065 Q1004 C1022 R1013 R1009 W060
W058
R1032
L4015
R4204 51 1
C1020 C1018 C1013 R1077 C1029 R1020 W098 R1044 W094 R660 D4001 R4054 R1001 W868 C4075 C4071 C1062 C4072 R1078
TP1002
W062 W063 W067 C1019 W102 R1012 W099 W107 IC1099 C4059 Q4012
R1028
R1053
CC001
C1030
Q4011
CP
W093
10
L4005
004
R4036 C1066 W128 R1070 C1091 C4027 R1010 C4007 C4048 1 W116 C4045 R4049 R4050 C4052 Q4009 C4016 C4011 W086 C4043 R4043 Q4007 W115 C4076 R4041 W118 C4077 W110 W114 R1029 R1023 R1027 Q4013 R4039 W130 W129
CP4
C4023
W091
R1024
R4032 W101 W100 W126 D4207 R4021 C4035 R4045 R4042 R4012 C4044 R4038 W854 L4007 C4013 C4036 R4018 C4040 R4009 C4022 C4012 C4031 R4031 C4037 R4030 C4030 C4018 C4017 W088 C4025 W147 R4011 R4010 C4015 R4064 C4005 R4058 CP4001 R4059 W141 W142 W137 L4004 C4028 R4004 Q4005 R4003 Q4002 R4060 R4007 Q4003 L4002 W201 W136 W134 C4006 R4008 C4089 C4008 R4015 Q4006 C4003 W808 W113 W111 C4009 W112 W165 C678 W157 R1003 C1070 W822 C1065 W168 IC1003 Q4204 C4207 CP1006 C4206
W133
C683
CP601
CP352
D622
C661
D1004
Q4001
W851
IC601
R357
R673
W146
R652
W169
C622 R617
R670
CD850
D1010
R628
D605
Q1008
C1043
CD820
R620
L604
C654
W829
W178
R646 R1060 R664 R640 C642 W177 IC352 C660 R351 C630 C634 R616 C356 R353 C685 L607 C675 C618 W184 R618 Q602 C359_1 R358 C352 W823
X604
IC 60 4
C623
R1058 C1055
R4203
W139 R360
Q1012
C648
C652
C650
C646
C645
R1057
R1038
Q1010
C638 W860
L611
C1042 R1035
W190 C621 C620 R653 41 D1018 C662 W203 C601 1 R634 C607 C641 C659 64 C615 C670 R667 C669 W828 R654 C643 C644 L613 R621 S801X C671 R639 Q608 C626 R625 W189 R626 R675 R623 W188 W181 C617 CF601 C616 W195 C687 L602 R636 R635 L610 C609 C614 C624 W186 C605 B602 CD810 D1008 R606 W812 W193 R1076 R1068 Q1006 W191 R612 L605 W187 W196 R613 R611 C613 TP601 C684 C656 C1079 C658 C612 C4209 TP4201 R4213 C4205 R4212 C625 R662 R4238 Q4212 R4244 W980 C4210 W194 W197 R4236 R4239 R663 Q4210 R1065 TU601 C657 R605 C604 W182 D601 R603
- REPLACE
AS MARKED.
Q1019
CP603
OF FIRE
C355_2
RISK
W832
Q352
CD604
S801Y
J4201
C4220
C4211
C668
C647 R619
W864
D604
C611
C357 C1044_1
Q605
R649
R651
C649
R632
Q1016
R1056
W159
W156 W152
Q1011
W171 W818
Q1015
W145
R650
C4002
D603
R630
R1037
W172
W170
R1069
W143
W173 D1001
C4001
R4005
C633
W154
W174
L4001
W162
W814
R1005
C4083
W161 R624 W164 R627 R631 W160 R686 C631 W158 R669 W163 Q4004 W148 R4001 L4003 W150
CP1005_1
W151
W804
D1007
C1001
W167
D4202
D1005
W153
W127
R1048
W090
R1008
C1007
D4201
CC002 31
L4012 W053
W054
W061
R1018
Q1 00 9
R1046 Q4206
R4028
I-6
(SYSCON PCB)
C4095 47K 1/4W 47K 1/4W 47K 1/4W 100P CH L4014 C4082 68uH 18P CH
R4020
R4025
C4097 0.1 B
L4015
Y/C_AUDIO
L4009
6.8K
6.8K
12K
100uH
R4019
R4024
R4027
L4012
100uH0607
0.1 B
C4055
C4084
C4079
100uH
0.1 B
R4029
ENV TP4001
GND
W813
C4027 16V 22 KA
C4041
2.2M
C4056
0.1 B
16V 33 KA
W854
C4042
C4023
R4028
0.047 B
0.022 B
C4029
50V 1KA
0.1 F
0.1 F
1 F
50V 1 KA
C4033
C4034
6
4 6 NC
0.1 B
2.7K
C4054
150P CH
C4024
0.01 B
C4094
8.2K
R4052
1 F
C4091
0.01 B
C4020
1 F
1.8K
1.2
C4047
C4050
C4051
C4053
4.5 CP4001 TOC-C09X-A1 9 8 GND GND GND SP-CH1 (R) SP COM SP-CH2 (L) EP/LP-CH1 (R) EP/LP COM EP/LP-CH2 (L) C4016 ENV_DET C4005 R4058 0.33 B 15K R4059 50V1 KA 1K R4012 3.9K 0 4.5 4.5 0 5.4 0 0 4.0 0 1.6 2.5 2.9
82
49 48 47
FROM/TO CYL/MOTOR
ID DET
84
NC NC NC NC 2.5 2.5 2.5 0 2.5 5.0 1.9 2.0 3.4 2.6 3.0 4.2 0 2.0 3.0 4.1 3.3 3.5 3.5 3.5 5.3 3.5 5.3 5.4 2.5 0 2.5 2.0 80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51 A-Vcc C-GND REC C-Vcc 4fsc APC S-DET -OUT H.A GND OUT VXO CLK SLD -IN R P C COMB KIL 320FH Vref DET VCO 2.3V CCD GND CCD Vcc NTSC:H P ALC H.A GND H.A VCC 320FH VCO Sub CONV BALANCER P R Main CONV BPF2 REC FM_AGC1 R A.GND MUTE AUTO BIAS Vref PB/EE EQ AMP 1 2 0 0 3 0 ALC DET REC/EE LINE AMP P R P TH S-EQ Vref PB /EE PB_FM EQ REC AMP S N FM AGC DET REC EQ OUT P ACC DET BAL/TC1 Y-Vcc CLAMP P R SERIAL DECODER CHARA CLAMP INS W/D CLIP DOUBLE NL DETAIL LIM EMPHA ENH R R P REC FM-AGC B-UP AMP FM DEM FM DEM C-LPF ACC DET ACC SUB LPF Y-LPF P R 1/2 P R R P FBC R P R P N.C.1 N.C.2 PIC_CTL ANR Y/C MIX SYNC DET TC2 TC1 EE AGC 6DB REC BGA R P KIL R P COMB AMP PB BGA BEFORE BPF1 VXO XO PB BGA AFTER P R CLAMP Y.N.R NL DE EMP VCA DET CCD LPF Y_DELAY R
R4007
81
18
50
NC 0.1 C4059 0.01 B 1.2 2.4 9.7 1.3 2.0 NC 5.3 C4058 2.0 50V1 KA 3.0 C4063 16 C4060 0.01 B C4061 0.01 B 0 1.3 BUFFER 2.1 Q4012 2SA1037AK C4062 16V 10 KA R4056 1K C4073 6.3V 47 KA C4074 0.01 B D4004 MTZJ5.6B C4065 0.1 B C4066 0.1 B FRONT_VIDEO C4064 0.01 B R4055 C4071 B4003 BL01RN1-A63
83
FROM/TO MICON VCR_A_MUTE COL_ROTA H.SW H.AMP_SW_1 SCL SDA D.V_SYNC V.REC_ST_H 15 TU_VIDEO ENV_DET CTL+ CTLCOMP
85
BEFORE AFTER
86
45
46
7 6 5 4 3 2 1
87
88
89
90
91
92
ENV DET
93
38 37 36
39
COMP OUT
40
REC FM AGC2
ALWAY 2.7 50V 1 KA 5V 5.2 REG 4.0 C4069 SYNC DET AGC DET AGC TEC2 2.2 0.1 B 4.9 1.8 3.1 1.8 1.4 2.2 3.0
96
35
4
R4009 R4008 10K 470
95
94
41
PB_FM AGC
42
43
44
97
98
33
SYNC SEP
34
H-PLL
1.8K 50V 1 KA C4072 0.01 B C4067 16V 33KA C4068 50V 3.3 KA D4001 2.2M 1/4W 1SS133 C4076 6.3V 100 KA C4077 0.1 B
4
SD_VIDEO REAR_VIDEO
100 99
R4071
Y-GND
L4002 5.2 V.REC_ST_H FROM/TO A/C HEAD 5.1 21.1 100uH SW 0607 Q4003 DTA124EKA
C4015 6.3V 47KA R4016 DRIVER Q4005 2SA1318 5.3 22K 5.0 5.0 L4004 100uH 0607 56K R4022 R4021
1.2K +-1%
0.0027 Y
4 5 2.5 0 C4030
6 0 R4031
7 0
8 0
31
C4037 0.033 B
C4040 50V1 KA
C4057 560PCH
PB EQ CTL 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 0 1.0 3.5 5.2 1.6 1.6 2.4 5.2 3.1 2.1 1.2 3.1 2.5 0 2.6 2.6 5.2 0 0.4 0.4 2.5 4.8 NC NC NC W815 R4053 560K 50V 2.2 KA 50V3.3 KA 0.01 B
32
V.REC_ST_H
C4017
0.1 B
C4035
0.01 B
5.6K
R4030
50V 4.7 KA
390
2 1
AE HEAD(-) AE HEAD(+) 2.7 AUDIO 21.2 PB SW Q4001 2SC3331 15.1 AUDIO 15.1 PB SW 20.8 Q4002 2SC3331 0 TO F/E HEAD
4 L4003 1626007
14
CTL-
CTL-
47
10K
CTL+
R4001
C4036
CTL+
AUDIO REC
R4060
C4089
11
AUDIO PB
C4031 820P CH
CP4005 52045-0645
R4018 27K
C4044
C4048
R4074
RECORD LUMINANCE SIGNAL PLAYBACK LUMINANCE SIGNAL RECORD COLOR SIGNAL PLAYBACK COLOR SIGNAL TUNER VIDEO SIGNAL AUDIO SIGNAL(REC)
R4043 L4011 2.7K C4043 5P CH R4042 220 R4045 680 2.5 C4052 R4050 180P CH 1.5K 4.7K 1.9 560 BUFFER Q4009 5.2 2SC2412K 270 1/4W 270 1/4W 100uH 0607 R4054 BUFFER Q4011 2SA1037AK 6.3V 100 KA R4057 330 470 2.3 3.0 C4070 C4075 0.1 B 68 1/4W
10K 1/4W
R4035
R4038
C4018
0.7 6.3V 330 KA C4009 0.033 B 0 BIAS OSC Q4006 2SC1317 C4006
3.0
W847
5.3
2.2K L4007
R4062
R4032
R4026
R4036
4.7K
18K 1/4W
1.3
1.3
R4063
R4004
1.9
R4046
R4061 47 1/4W
120
10K
390P CH
120uH
Y/C_VIDEO
SD_VIDEO
R4051
R4039
W808
270
VCR_A_MUTE
H.AMP_SW_1
H.SW
SDA
SCL
FE HEAD(HOT)
D.V_SYNC
FE HEAD(GND)
COL_ROTA
V.REC_ST_H
CP4004
TMC-T02X-E1
L4008
1
NOTE: THE DC VOLTAGE AT EACH PART WAS
MEASURED WITH THE DIGITAL TESTER DURING PLAYBACK
PCB010 VM9175
NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
CAUTION: SINCE THESE PARTS MARKED BY CRITICAL FOR SAFETY,USE ONES DESCRIBED IN PARTS LIST ONLY
ARE
ATTENTION: LES PIECES REPAREES PAR UN ETANT DANGEREUSES AN POINT DE VUE SECURITE NUTILISER QUE CELLS DECRITES DANS LA NOMENCLATURE DES PIECES
I-7
A
FROM/TO POWER AT+5.6V D1011 D1006
B
SB10-03A3 SB10-03A3
F
TP1001 SERVICE NC
(SYSCON PCB)
C1082 0.01 B OSD_BLK CENTLED C1041 100P CH 0.1 B R1032 10K
R1059 100P CH R1055 25 INVERTER Q1016 2SC2412K -0.7 C1053 100P CH R1058 4.7K C1055 330P CH 10K R1060 100K 27
R1028
10K
C1006
0.01 B
MOTOR_GND LOADING MOTOR DRIVER IC1003 BA6955AN R1017 33K R1020 22K R1044 W810 3.3K R1045 3.3K R1001 R1053 3.3K 1/4W NC 0.9 0.9 0 1.8 2.5 80 79 78 77 76 75 DRUM-PWM CAP-PWM E/V_MASK AGC(REC) 81 REEL-S REEL-T 0 5.1 5.1 NC 5.1 5.9 NC 2.6 B 2.5 0 21 CYL_PG C1015 BOT EOT C1016 C1018 CENTLED CTLCTL+ LMLM+ C1002 CP1002 1 2 CH22076A EOT R1011 82K R1003 VCC D1003 SID1050CM R1016 0.001 Y 82K C1005 0.001 Y FF/REW_SW Q1004 DTC124EKA C1025 0 5.1 0 0.1 B C1022 0.1 B R1012 10K C1019 0.001 CH R1009 560 10V 47 KA 16V 22 KA 50V 4.7 KA 22 2.0 0.6 2.5 2.5 0.2 0 NC NC NC NC 0 5.2 2.5 2.6 5.1 74 73 72 71 70 69 68 67 JUST CLOCK SP-H IIC-DATA1 IIC-DATA2 IIC-DATA3 IIC-CLK1 IIC-CLK3 IIC-OFF
C1073
26
56P CH
4.7K 1/4W
C1029
W839
C1071
4.2
0 R1057 47K
CONTROL LOGIC STD R1064 MTZJ5.1B POWER SAVE 1 12.1 2 0 3 0 4 0 5 10.8 6 0 7 10.9 8 12.1 25V100 YK X_RAY 10K C1072 1 F R1075 5.9 0.2 4.7K 0 X_RAY_SW Q1023 2SC2412K
28
7
FROM/TO Y/C/A/H.AMP H.SW SCL SDA SD_VIDEO ENV_DET VCR_A_MUTE CTL+ CTLCOL_ROTA D.V_SYNC V.REC_ST_H H.AMP_SW_1 COMP
220 1/4W
C1031 0.001 Y 560P CH 5.2 51 SERVICE 50 5.2 0 0 4.9 W841 0 0.1 0 2.6 2.5 5.2 NC 0 NC 0 0 2.6 2.1 5.2 1.3 1.5 5.2 NC 0 0 0 W803 5.2 0.001 B C1068 5.2 BUFFER Q1017 4.5 2SC2412K C1030 5.2 2.5 W873 C1070 0.1 B 1K 5 EEP ROM IC1099 S-24C04BDP-LA SDA 2.6 6 SCL 0 7 TEST 0.1 B 5.2 8 VCC 5.2 BUFFER Q1018 2SC2412K 4.5 VCR_POWER_H FROM/TO I/O IIC_OFF TV_POWER_H EXT_MUTE ON_TIM_LED OTPB_LED TV_POWER_H REC_LED T-REC_LED PLAY_LED VSS A2 A1 A0 0.1 B 0.1 B KEY_A KEY_B REMOCON_IN SCL SDA TO SOUND AMP C1014 0.1 F TV_POWER_H TV_A_MUTE R1040 33K 1/4W L1001 2.2uH C1047 18P CH FROM/TO CHROMA/IF HD VD 24 X1001 12MHz C1048 18P CH C1049 22P CH X1002 32.768KHz C1050 20P CH RESET TV_POWER_H OTPB_LED ON_TIM_LED VCR_POWER_H TRICK-PB-H C1026 0.1 B X_RAY C1040 18P CH AFT_M SCL SDA OSD_R OSD_G OSD_B OSD_BLK W840 R1033 1K C1062 1M R1078 390K TAB_SW R1034 0.1 B
R1039
18K D1014
C1001
CENTER LED
84
CA/MA_SEL POWER_FAIL_L CFG AMP-OUT CAP-FG AMP-VSS DRUM-FG DRUM-PG AMP-VREFOUT AMP-VREFIN C CTLCTL+ AMP C CTL AMP-OUT DUMMY-V.SYNC COLOR ROTARY HEAD.AMP.SW REMOCON-IN ENV-CMP-IN VIDEO-H.SW HI-FI-H.SW VCR-POWER TRICK-PB-H VIDEO-ENV AFT(MONI) EXT-MUTE 98 AMP-VCC 99 ANALOG VCC 100 DEW 33 AKB CTL 32 OTPB LED 81 VCR_A_MUTE 82 TV_A_MUTE 83 FF/REW-L 50 TAB SW 49 OSD-VSS 48 CM_ADV_AUDIO
CM_ADV_VIDEO NUB OSC-OUT2 OSC-IN2 CLKSEL AV 2 AV 1 VSS X-OUT(12MHz) X-IN(12MHz) VCC XC_OUT(32KHz) 31 ON-TIMER LED XC_IN(32KHz) RESET-L TV-POWER
47
W804
R1005 2.7
D1001
83
48
1K
82
49
TV_A_MUTE
R1077
V-REC-ST-H
SD-IN(MONI)
NUA
OSD OUT1
H/C-SYNC
CAP FULL
OSD-VCC
V-SYNC
CVIN
HLF
VCR_A_MUTE
VHOLD
D1004 D1005
C1038
85
46
88
89
90
91
93
38
92
39
40
41
42
CYL_FG
43
1 F
1K 1/4W
87
44
CAP_FG
C1007
R1008
86
45
C1046 20P CH
95
94
96
97
98
CAP-LIMIT
LDM-FWD
SENS LED
PLAY LED
LDM-RVS
MSSEN-A
MSSEN-B
CAP-FWD
T-REC LED
HI-FI-ENV
AFT(REC)
CAP-HI H
REC LED
100 99
KEY A
BOT
EOT
KEY B
270 1/4W
R1048
R1018
4 0
5 0
4.7K
W819
6 7 8 2.4 2.2 0
31
32
33
23
2.5
34
2.6
35
36
37
5.1 FROM/TO MICRO MOTOR CP1005_1 52045-0545 5 4 3 2 1 CYL DRIVE CYL GND CYL FG CYL +B CYL PG 0
R1070 18K
2.6
REMOCON_IN
100P CH
C1088
0.1 B
TRICK-PB-H
R1076
H.SW TP1002
19
1 4 SPVF130100 C1063
SW1001
EXT_MUTE
PLAY_LED
T-REC_LED
1K
SEN_LED
CAP_HI_H
REC_LED
LDM_R
BOT C1090
COMP
LDM_F
AFT_M
KEY_A
KEY_B
4 SDA SCL 0 0
3 0
2 0
R1061
R1062
C1078
1K
3
R1023 1K 1/4W R1027 1K 1/4W
C1077
EOT
CYL_DRIVE MS_SEN-B MS_SEN-A SEN_LED REEL_S REEL_T C1074 CYL_FG CYL_PG 6.3V 220 KA 6.3V 100 KA R1066 C1032 R1046 R1002 R1047 C1058 0.0022 B RESET
4.7K
120
4.7K
1K
22 1/4W
R1079
R1006
47K
0.1 B C1066
1 2 3 4 5 6 7 8
GND MOTOR GND I LIMIT VCO FG CAP.M F/R VCC(5V) R1010 3.3K 1/4W CAP_VCO CAP_FG CAP_F/R W814 CTL CAP_CTL
1.2 2
5.2 3
0.8 2
C1003_1
CP1004
TMC-J08P-B1
2.4
1.2
1.2
6.3V 1000 YK
5.1
47K
C1091
R1019
33K 1/4W
R1083
R1050
16V33 KA
4 1.4
1 0.5
TUNER VIDEO SIGNAL DEFLECTION SIGNAL CAPSTAN AFC SIGNAL CYLINDER AFC SIGNAL CYLINDER APC SIGNAL
CAUTION: DIGITAL TRANSISTOR
PCB010 VM9175
C1017
NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
NOTE: THE RESISTOR MARKED F IS FUSE RESISTOR. THE ALUMI ELECTROLYTIC CAPACITOR MARKED NP IS NON POLAR ONE.
CAUTION: SINCE THESE PARTS MARKED BY CRITICAL FOR SAFETY,USE ONES DESCRIBED IN PARTS LIST ONLY
ARE
ATTENTION: LES PIECES REPAREES PAR UN ETANT DANGEREUSES AN POINT DE VUE SECURITE NUTILISER QUE CELLS DECRITES DANS LA NOMENCLATURE DES PIECES
C1021
0.1 B
I-8
82P CH R667
R639
15uH C670
L602
1K
10K
TU_VIDEO
1.1 L613 R618 5.6K 47uH C675 22P CH VCO 50V0.47 KA C617 6 1 2 3 R654 2.2K
R621 4.7K
35
FROM/TO Y/C/A/H.AMP TU_VIDEO TU_AUDIO C630 0.01 B 3.579545MHz 100CT3R505 V/C GND 16V47 KA 50V0.47 KA R635 24K R636 C659 50V2.2 KA C634 24K
TP601
C660
X604
16P CH
2.2M
C641
50V0.47 KA
16V10 KA
C643
TO I/O AGC B.OUT 0 42 0 41 40 0 0 HOR GND 0 2.4 0 0 R640 1.7 18K 1/4W 4.2 0 0 1.2 2.6 5.1 2.5 2.4 2.4 HD X_RAY C648 R664 4.7K +-1% R637 MTZJ9.1B D601 5.6K REF R645 10K C665 100P CH FROM/TO DEFLECTION R642 R641 3K 0.015 B C650 50V 1 KA C652 50V 0.47 KA 100 H_OUT CD820(CP820) CH2B027A 1 SOUND GND SOUND+B VCR_POWER_H TV_POWER_H C654 50V0.22 KA V_OUT H_OUT VD V_OUT VCR POWER H TV POWER H GND H.OUT V.PULSE V.OUT ACL AFC X.RAY 2 3 4 5 6 7 8 9 10 11 HD R648 R646 3.9K 5.6K AUDIO_OUT SOUND_GND SOUND+B GND TO SOUND AMP
C626
R625
34
33
R634
6
C647 50V 2.2 KA R606 10V220 YK 0.1 B C624 50V 1 KA Y/C_AUDIO R611 470 R612 1.5K 0.1 B C684 R605 4.7K C613 10P CH C625 50V 1 KA C614 0.001 Y C609 0.01 B 0.001 Y R619 150 2.4 2.1 1.2 2.4 3.1 0 0 32 AUDIO_OUT C658 0.0056 B TU_AUDIO C612 0.0082 B R613 6.8K 1/4W
14
0 64 65
0 63
0 62
0 61
0 50
NC 49
R663
C604
C605
27K C656
0.1 B
C657
220
66
AGC 1 2 3 SCL 4
1.8 NC
X-RAY
R662
BL01RN1-A63
220
TRPP 67
VIDEO DET
PPC1 BPF
FILTER ADJ
68
69
5
TECC1040PG31A
70
71
+5V 7 8 +30V 9
4.9 NC
0 0.8
DC VOL
72
PFC1
73
29.3 NC
74
TU601
10 IF 11
15
31 C615
H_GND
75
76
R603
BLACK STRETCH AFT VER SEP OSD FIX GAIN OSD SW VER C/D HOR VOC VER RAMP
29
IF AGC RF AGC
VIF
30
31
32
33
34
NC
SW
TRPP
ACC
SYNC SEP
HOR C/D
PFC2
35
SDA 5
2.5
SW 1/256 FBP
36
2.5
37
2.5
38
VIDEO PMP
VIDEO SW
39
13
12
B602
P2C PLL
CLMP
CLMP
VC0
1K
L610 3602038
C642 0.001 Y
CW KIL
77
C616 0.01 B
IN IN G OUTOUT 1 2 3 4 5
78
2.9 2.9 0
79
80
AKB 21 0 22 0 23 0 24 0
1 0
2 0
3 0
4 0
5 0
6 4.9
7 2.8
8 2.4
0.01 B
10 11 12 13 14 15 16 17 18 19 20 5.1 5.1 4.2 5.5 5.5 1.2 5.1 8.1 3.2 3.2 3.2 0
C607
W863
W864
5P CH
C687
R620 100K
W865
100 1/2W
100 1/2W
7.5K
3
FROM POWER AT+30V GND P.CON+5V P.CON+9V C661 D622 L608 100uH 0607 W872
16V 470 YK
25
BUS
ABL
CLAMP
DRIVE/CUT-OFF
26
27
28
3
C649 100P CH 0.01 F 15K 16V100 YK C646 150 1/2W 0.01 F R638 C645 R647 27K
47P CH
33P CH C678
C623 50V 1 KA
100uH
C674
C676
47P CH
0.01
39K
C631
C638
R686
R670
R632
C640
R601
R617 C622
W860
TO CRT R628 12K 1/4W 10K 1/4W 16V 100 KA R652 C633 D605 11ES1N R630 1.5K 1/4W R650 470 1/4W D603 D604 CUT OFF Q605 2SA733_Q 0.2 0 50V10 KA R651 220 CD850 (CP850) CH25080A GND 5 CUT OFF G.OUT 0.9 R.OUT B.OUT G.OUT R.OUT B.OUT 4 3 2 1
1K
1K
AFT_M R673
R624
R627
OSD_R R659
OSD_G R660
OSD_B R661
P.CON+10V
OSD_BLKR631
1K
R.OUT
G.OUT
B.OUT
SDA
R.SIGNAL G.SIGNAL B.SIGNAL LUMINANCE SIGNAL COLOR SIGNAL DEFLECTION SIGNAL AUDIO SIGNAL(REC) AUDIO SIGNAL(PB) TUNER VIDEO SIGNAL TUNER AUDIO SIGNAL
A
SCL
68K
CAUTION: SINCE THESE PARTS MARKED BY CRITICAL FOR SAFETY,USE ONES DESCRIBED IN PARTS LIST ONLY
ARE
NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE CAUTION: DIGITAL TRANSISTOR
R669
L102 HF57T18.5*10*10
ATTENTION: LES PIECES REPAREES PAR UN ETANT DANGEREUSES AN POINT DE VUE SECURITE NUTILISER QUE CELLS DECRITES DANS LA NOMENCLATURE DES PIECES
PCB010 VM9175
I-9
(SYSCON PCB)
FROM/TO OPERATION
T-REC LED
OTPB LED
FRONT VIDEO IN
SOUND OUT L
REC LED
KEY B
KEY A
FRONT A IN L
B OUT
AT 5V
GND
IIC OFF
GND
AGC
SDA
SP OUT L
SCL
GND
GND
FROM/TO OPERATION
FROM/TO SOUND AMP FROM/TO MICON ON_TIM_LED SB10-03A3 0 0 4.5 0 ON TIM LED SW 0 Q4201 DTC114EKA 3.6 REC LED SW Q4205 DTC114EKA 0 3.6 3.6 T-REC LED SW Q4206 DTC114EKA 0 0 0 SOUND_GND SOUND+ SP_OUT D4202 4.5 0 IIC_OFF SDA SCL OTPB_LED REC_LED T-REC_LED KEY_B KEY_A P.CON+9V PLAY LED SW Q4207 DTC114EKA 0 OTPB LED SW Q4202 DTC114EKA 0.1 B C4206 C4207 0 4.5 0 470P CH C4204 R4201
0.1 B
MTZJ6.8B
D4207
75 1/4W
PLAY_LED
Y/C_VIDEO REAR_AUDIO REAR_VIDEO Y/C_AUDIO R4203 100 L4205 R4232 10K 100uH D4201 MTZJ5.6B R4204 1K
W980
R4244 1K
C4209 30 25V 10 KA
V.OUT TP4201 29 R4213 75 470P CH 470P CH C4210 C4205 IN 6 AUDIO OUT IN 3 VIDEO C4211 16V470 YK 1.9 2.5 R4212 R4236 BUFFER 0 Q4212 2SA1037AK 1K 75 5 2 OUT 1 GND R4239 220 1/2W R4238 33
8.5
B.SIGNAL AUDIO SIGNAL(REC) AUDIO SIGNAL(PB) TUNER AUDIO SIGNAL TUNER VIDEO SIGNAL
2
4 GND
NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
10V100 YK
C4220
I-10
(SYSCON PCB)
MOTOR_GND
CAP_VCO
P.CON+12V
P.CON+9V
P.CON+5V
6
25.1 DRIVER Q1011 2SD2396 2.5 2.8 R1037 1.2K D1010 1N4005E 50V10 KA
C1004 35V220 YK P.CON 5V DRIVER Q1019 2SB1134R 5.3 11ES1N D1007 4.5 5.2
50V 1 KA
23.6 FROM TV POWER CD810(CP810) CH2A014A 1 GND AT+12V AT+12V P.CON+9V AT+5.6V MOTOR GND AT+30V POWER FAIL(DC) AT+21V AT+10V W812 AT+30V POWER_FAIL[DC] C1056 6.3V 470 YK 2 3 4 5 6 7 8 9 10 CAP_HI_H 0 0
1.8K C1042
2.5
2.8
R1038
2.2K
C1043
25.1
2.5
R1035
P.CON+12V MOTOR_GND GND POWER_FAIL[DC] 4.5 P.CON SW Q1006 2SC2412K 4.2 3.5 TO I/O 100 1/2W P.CON+9V AT+5.6V 6.3V 220 KA C1079 0.1 B C1037 GND R1068 R1069 1.5K 1/4W CAP_HI_H VCR_POWER_H
AT+5.6V
GND
4
D1018 11EQS04N
NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
CAUTION: SINCE THESE PARTS MARKED BY CRITICAL FOR SAFETY,USE ONES DESCRIBED IN PARTS LIST ONLY
ARE
ATTENTION: LES PIECES REPAREES PAR UN ETANT DANGEREUSES AN POINT DE VUE SECURITE NUTILISER QUE CELLS DECRITES DANS LA NOMENCLATURE DES PIECES
PCB010 VM9175
I-11
(SYSCON PCB)
+
1 8.2 2 3.5 3 0
36
CP353
B2B-EH-A 1 2
CD353 CH12437A 1 2
SPEAKER
KA
6
SP351 810-47-171
50V 1
C359_1
50V 0.1
W823
CD354 CH12438A 1 2
SPEAKER
SP352 810-47-171
5
FROM CHROMA/IF SOUND+B AUDIO_OUT (S803) SOUND_GND GND R360 12W
4
CC001CC002
W832 R353 68K 25V2200 YK 16V10 KA FROM/TO TV POWER 1 GND 50V10 KA C357 C354
CD604(CP804) CH01005A
C356
HS351 763WAA0131 NC
S801X
R351 10K
1
NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE NOTE: THE DC VOLTAGE AT EACH PART WAS MEASURED
WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL.
1
CAUTION: SINCE THESE PARTS MARKED BY CRITICAL FOR SAFETY,USE ONES DESCRIBED IN PARTS LIST ONLY ARE ATTENTION: LES PIECES REPAREES PAR UN ETANT DANGEREUSES AN POINT DE VUE SECURITE NUTILISER QUE CELLS DECRITES DANS LA NOMENCLATURE DES PIECES
PCB010 VM9175
I-12
MAIN/CRT
CP820 W028 W827 C424 C425_1 W027 W826 C423 W823 R447 W014 W047 C511_1 R423 W822 W817 IC505 C537 R531 W813 R535 Q501 R517_1 R518 R554 HS505 Q406 HS402 TP402 C520_1 CP804 C538 W012 D536 D515 R512 CP810 C532_1 C528 W004 W020 W006 HS503
IC502
IC504
S803Y FH503
HS502
R5
C540_2
W843
R528 D519
10
D510_1
F502 Q502
W017
FB401
W018 D532
C536_1
W816 R460
W825 C422_1
FH504 Q503
W811
R456
D509
C438
C418_1
C531_1
D505
ICP505
T401
L401 C450
D524 D530
C417
R44 8_3
R449
C416
CP811
7 50 C
R490 C432 R453 C429_1 W048 W031 W850 W831 L402 CP401 TP403 TP401 Q405
R513
R516 W810
R5
Q513 W039
05
R81
CP802
CP807
02
01
TP8
TP8
TP8
Q804
03
C80
W835
Q507 Q520
Q805
W803
W808
C822
C530 R532
FH502
F501
FH501
CP
CP850 CC005
80
CC001
I-13
R5
W802 W809 W016
R808
R802
00
W839 D502 D503 C514_1 C503 D504 R501 HS501 B505 R502 D506 D521 T501 D501
R454 R406 C430_1 D412 R442 W812 R443_1 R444 D411 D413
W023 D408 R417 W036 C406_1 R404 R419 T502 W022 VR502 R441 R549
D409
R530
D535 RY501
R523
W037
C502
HS401
W034
W033
R401
C512_1
R503 R506
C510_3
R553
CD803 CP803A
C431_1
R421
CP502
C421_1
C402 C401_1
C515
IC506
R542
TH501
D529
C433_1
R529_1
C508
C505
C549
R80 5
W025
(MAIN PCB)
GND 1 0
VCC 6 4.9 35V100 MHE 680 1/2W TO DY CP401 B05B-DVS 5 100V 0.47 TF 270 1/2W R419 220 1/2W C411 R417 C413 7
7
11E1N D401 C412 18K R401 R402 18K 1/4W 500V390P B 50V 4.7 YK 0.001 M C406_1
R421
C401_1
R409
27K
C402
C409 0.0022 M R404 3 3.3K R411_1 11K R413 10K R414 1.8K
100V0.1 TF
4 3 NC 2 1
6
FROM/TO CHROMA/IF CP820 (CD820) 8283_1112_00_000 1 2 3 4 5 6 7 8 9 SOUND GND SOUND+B VCR POWER_H TV POWER_H GND H.OUT V.PULSE V.OUT ACL AFC X.RAY TP402 JWF-50K-1
25V 1200 HR
6
50V100 YK 680 1/2W R408_1
50V 2.2 YK
C403_1
C405
R407
10K
15 1/4W
R415_2
R418_1
HS401 763WSA0004
2.2 1/4W
CC004 TP-1S-05 V801 A34JXV70X28N45 L401 W825 4.7mH0909 250V 1 MHE C422_1 L402 ELH5L4112 C431_1 250V10 YK D413
11
250V0.33 ECWF
10
9 10 8 6 11
500V 0.001 B
RMPG06J C430_1
R G B 5 7 1
C423
R448_3 1K 1W C450 2KV0.001 BP FB401 3213012R 2 262.0 10 5 9 2 COL +180 +B EF FOCUS HV 1 1 CD802 CH01010A TO CRT
68 1/2W
R447
W826
CD801 8M82025A
C416 C417 500V560P B 500V 22P SL 0.5 H.DRIVE Q405 2SC2271 31.0 0
T401 305Y002 31.0 3 NC 2 0.2 1 160V1 MHE 22.3 4.7K 1/2W C418_1 4
2KV
6 C438 1.3
W812
W827
R456
HS402 763WSA0004
SCREEN
NC 6 NC C429_1 2KV 470P B W831 0 GND 3 22.3 +14 NC 7 1.5 D411 RMPG06J 8 +12
R443_1
R439
TO CRT
100V22 MHE
3
C433_1 22K 1/4W +-1% R441 R440 R444
3
180V R450_1 4.7 1W NC GND GND HEATER 100V0.47 TF 68K 1/4W C432 CP803A 51052-0500 5 4 3 2 1 GND GND HEATER CD803 2E053002 180V
HZ27-1L
TP401 D409 R442 15K 1/4W +-1% TP403 R423 2.7K 1/4W D412 RMPG06J
HZ11B3L TP404
35V1000 MHE
6.8K 7W
R449
C421_1
R490
P.CON+125V GND
DEFLECTION SIGNAL
PCB070 TM9433
NOTE: THE RESISTOR MARKED F IS FUSE RESISTOR. THE ALUMI ELECTROLYTIC CAPACITOR MARKED NP IS NON POLAR ONE.
NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
ATTENTION: LES PIECES REPAREES PAR UN ETANT DANGEREUSES AN POINT DE VUE SECURITE NUTILISER QUE CELLS DECRITES DANS LA NOMENCLATURE DES PIECES
CAUTION: SINCE THESE PARTS MARKED BY CRITICAL FOR SAFETY,USE ONES DESCRIBED IN PARTS LIST ONLY
ARE
I-14
(MAIN PCB)
TV.POWER_H P.CON+125V R515 D532 R521 10K 10K 1/4W 127.0 +B 100V DRIVE Q503 2SC4160 127.5 -OEC-YAC1 127.0 160V 10 MHE R520 100V DRIVE Q502 2SA1371 126.8 10K 11E1N R518 D527 11E1N D530 11E1N C537 R531 2.5A 250V 1K 50V4.7 MHE F502 2.5A250V 23302.5 6V POWER REG IC505 KIA7806PI IN 1 0.6 R535 4.7K D524 11E1N D531 35V 470 MHE C536_1 11E1N 24.0 HS505 763WAA0110 GND 2 0 W822 OUT 3 10V470 MHE 6.0 C538_1 FH504 EYF-52BC 10K 127.0 127.5
CAUTION: FOR CONTINUED PROTECTION AGAINST FIRE HAZARD, REPLACE ONLY WITH THE SAME TYPE FUSE 5A 125V (F501,ICP503,ICP504),2.5A 250V(F502), 4A 125V(ICP502) AND 2A 125V(ICP505). (3A) ATTENTION: POUR UNE PROTECTION CONTINUE LES RISQUES DINCEIE NUTILISER QUE DES FUSIBLE DE MEME TYPE 5A 125V(F501,ICP503,ICP504),2.5A 250V(F502), 4A 125V(ICP502) ET 2A 125V(ICP505). (3A) CAUTION: ICP502,ICP503,ICP504,AND ICP505 ARE MANUFACTURED BY LITTELFUSE INC.,TYPE 251.
160V47 BXA
C541
FH503 EYF-52BC
R519
100K 1/2W
C540_2
D536 11ES1N
125V 0.001 MX
125V 0.001 MX
R500
C530
C508
1 R517_1 0.33 2W
C516 3A 125V ICP505 251003 3A125V 500V470PB D505 21DQ09N D509 21DQ09N
R501 1.2 7W
6
P
L501_1 SS28V-15125
SOUND_GND C507_2
RM11C
RM11C
3 1
200V470 MXR
D510_1 RU2AM T502 52.7 1 52.7 9 8 2 7 NC 52.5 3 6 52.5 4 5 8.4 8.4 5V POWER REG IC502 KIA7806PI IN 1 D512 C531_1 21DQ09N 16V 1000 MHE 10.2 0.6 GND 2 5.2 AT+5.6V W811 OUT 3 W813 0136001 8.4 8.4 B504 BL01RN1-A63 100K 1/2W C517 2KV820P BP R509 160V220 PR C521 R512 27K 1W 0.022 F D515 HZ30-1L C528
AT+30V
TH501 PTH451C3R0Q11
250V 0.22 ECQUL
C502
C503
C505
P.CON+9V GND
5
AC120V 60Hz CD501 0R614918 1 1 BLACK WHITE BLADE WIDE BLACK WHITE
W809
W810
T501 8 143.8 SW REG IC501 STR-F6612 CONT DRIVER 22K 3W 0 FB/ OCP 1 1.7 1 R549 10K C512_1 5.0 0 0 0 5.0 0 SWITCHING Q521 DTC114TS C549 R552 1 7.3 0.033 M 10K C554 0.0022 M 6.0 6.3 6.3 FEED BACK SWITCHING Q507 2SC945 R533 390 SWITCHING Q520 DTC114TS 10 BL02RN2-R62T4 FEED BACK IC506 TLP621(D4-GR-LF2) 10.1 4 R503 3.3K 470PB C514_1 0.2 2 100.5 GND NC 5 4 104.0 R505 6
8135050W 16 15 14 13 12 11
W843
HS502 763WAA0081
10V470 MHE
CP501 THL-P03P-B1
251004 4A125V
C526
S 3
D 4 18.5
VCC 5 0
10 9
W839
251005 5A125V
B502
FROM/TO CHROMA/IF IN 1 14.0 R510 C511_1 9.0 16V 470 MHE OUT 2 0 GND 3 4.6 STOP 4 CP804(CD604) 003P-2100 GND 1
3
+B ADJ. 1SS133 1SS133 VR502 330 D523 D529
D521 R506 2.2K 1/2W 1SS133 0.15 1W R542 5A 125V HS501 763WAA0006 GND1 ICP503 251005 5A125V C519 500V470P B D519 21DQ09N 125V 0.0022 MX 25V470 MHE
5.4
W837
0.0012 M
C515
R514
(W014)
1.2
3W
100
TO POWER CP810 (CD810) 8283_1012_00_000 GND AT+12V AT+12V P.CON+9V AT+5.6V AT+5.6V MOTOR GND AT+30V POWER_FAIL AT+30V AT+21V 1 2 3 4 5 6 7 9 10
HZ6A3L
D528
C529
R516 390
R553
R532 330
470
CAUTION:
C524_1
IN 1 16.0
GND 2
OUT 3
16V470 MHE
5.2
R528 100
AT+125V
11E1N
W818
D535 11ES1N
D534
C532_1
PCB070 TM9433
1
NOTE: THE DC VOLTAGE AT EACH PART WAS MEASURED
WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL.
CAUTION: DIGITAL TRANSISTOR NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE ATTENTION: LES PIECES REPAREES PAR UN ETANT DANGEREUSES AN POINT DE VUE SECURITE NUTILISER QUE CELLS DECRITES DANS LA NOMENCLATURE DES PIECES CAUTION: SINCE THESE PARTS MARKED BY CRITICAL FOR SAFETY,USE ONES DESCRIBED IN PARTS LIST ONLY ARE
S803X S803Y
I-15
(CRT PCB)
0 7
FROM CHROMA/IF CP850(CD850) 8283_0512_00_000 5 4 3 2 1 GND CUT OFF G.OUT R.OUT B.OUT 2.8 2.5 132.5
1
0
J801 HPS3200-010501
2.7K 1/4W
R814
220
270P B
C809
2.9 2.5
W804
5
R808 2.7K 1/4W
560P B
R812 4.7K
220P B
R815
C810
220
3
470P B C801 2KV0.001 BP C820 250V 1 YK W814
W835
R816
R813 4.7K
C811
220
ACCESSORY
C805 GND GND SCREEN HEATER 100P B CP802(CD802) 003P-2100 ANT001 T4-216BNK-BK TM101 SBJY0P011A CP803B 51052-0500 HEATER GND BT101 UM-4/R03
2
NC GND 180V GND
FROM DEFLECTION
FROM DEFLECTION
CP807 005P-2100
SCREEN
GND
GND
180V
PCB110 TC9293
GND
NC
1
CAUTION: SINCE THESE PARTS MARKED BY CRITICAL FOR SAFETY,USE ONES DESCRIBED IN PARTS LIST ONLY ARE ATTENTION: LES PIECES REPAREES PAR UN ETANT DANGEREUSES AN POINT DE VUE SECURITE NUTILISER QUE CELLS DECRITES DANS LA NOMENCLATURE DES PIECES NOTE: THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE NOTE: THE DC VOLTAGE AT EACH PART WAS MEASURED
WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL.
I-16
INTERCONNECTION DIAGRAM
8
OPERATION
PCB030 TEXA19
4 3
2 1
H 1
J351 5 4 3 2
E J701
6 7
HALL SENSOR
MAIN COIL
ROTOR MAGNET
MR FG SENSOR
7
VCC O 4 GND / SOUND GND 4 FRONT VIDEO IN G 7 6 5 3 FRONT A IN L 2 GND 1
11
10
OTPB/PLAY LED
REMOCON OUT
ON TIMER LED
POWER ON L
SOUND OUT L
PLAY LED
T-REC LED
SP OUT L
REC LED
AT+5V
KEY B
KEY A
GND
GND
11
10
CP354
CP351
HALL HALL VCC IN CP1004 1 2 3 4 5 GND MOTOR GND I LIMIT CTL VCO FG CAP.M F/R VCC(5V) 1 2 3 4 5 6 7 8
SP351 SPEAKER 1
6
SP352 SPEAKER
6
CAPSTAN DD UNIT DECK MECHA ASSY M2001
6 7 8
CP601 1 2 P.CON+10V GND CP4005 6 5 4 3 GND CD820 SOUND GND SOUND+B VCR POWER H TV POWER H GND H.OUT V.PULSE V.OUT ACL AFC X.RAY 1 2 3 4 5 6 7 8 9 10 11 CP4004 FE HEAD (GND) FE HEAD (HOT) 1 2 RED CP1002 WHITE 2 1 2 1 AUDIO PB AUDIO REC CTL+ CTLAE HEAD(-) AE HEAD(+) FFC 6 5 4 3 2 1 AUDIO PB AUDIO REC CTL+ CTLAE HEAD(-) AE HEAD(+)
CD604 1
CONTROL
AE
DECK
PCB550 VE8851
2 1
2 1
4
RED CP101 VCC BOT LDMLDM+ 4 3 2 1 LM LOADING MOTOR M101 MICRO MOTOR M2003 WHITE BOT SENSOR Q101
POWER FAIL(DC)
VCR POWER H
SOUND GND
TV POWER H
MOTOR GND
CD810 AT+21V AT+10V CRT ANODE H.V 10 9 DY CP401 V801 GND AT+12V AT+12V P.CON+9V AT+5.6V MOTOR GND AT+30V 6 5 4 3 CRT SOCKET J801 7 8 9 B.OUT R.OUT 1 F CD802 G.OUT CUT OFF CP802 1 GND CD801 GND AT+21V AT+10V 1 2 3 4 5 6 7 9 10 CD850 1 2 NC 3 4 5 NC
14
CP1006 1 2 3 4
FFC
SOUND+B
P.CON+9V
AT+12V
AT+12V
AT+5.6V 5
V.PULSE
10
11
AT+30V
H.OUT
X.RAY
V.OUT
GND
ACL
AFC
GND
CP820
3
P.CON+10V GND
1 2
3
CYLINDER UNIT ASSY UN4001
CP1005 5 4 3 2 1 CP4001 9 GND GND GND SP-CH1 (R) SP COM SP-CH2 (L) EP/LP-CH1 (R) EP/LP COM EP/LP-CH2 (L) CYL DRIVE CYL GND CYL FG CYL +B CYL PG
11 IF NC 10 9 +30V 8 7 +5V 6 5 SDA 4 SCL J4201 NC AUDIO IN 6 1 2 3 4 5 VIDEO 5 OUT IN 3 2 OUT 1 GND 3 2 1 AGC
12 13
GND
FBT FB401
8 7 6 5 4 3 2 1
2 1
CP502 CP801 CP803A 1 HEATER GND GND NC 180V SCREEN NC NC 2 3 CP501 4 5 1 1 2 2 CD803 CP803B HEATER GND GND NC 180V 1 2 3 4 5 B.OUT R.OUT G.OUT CUT OFF GND 1 2 GND GND CP850
SYSCON
PCB010 VM9175
4 GND
FOCUS
MAIN
PCB070 TM9433
FOCUS SCREEN
CRT
CP807 1 PCB110 TC9293
CAUTION: SINCE THESE PARTS MARKED BY CRITICAL FOR SAFETY,USE ONES DESCRIBED IN PARTS LIST ONLY
ARE
ATTENTION: LES PIECES REPAREES PAR UN ETANT DANGEREUSES AN POINT DE VUE SECURITE NUTILISER QUE CELLS DECRITES DANS LA NOMENCLATURE DES PIECES
NOTE: THIS INTERCONNECTION DIAGRAM IS THE LATEST AT THE TIME OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICE
I-17
WAVEFORMS
TV POWER Y/C/AUDIO/HEAD AMP
1 5.0V 0.1ms/div
50.0V 20 s/div
11 PB 0.5V 0.5ms/div
DEFLECTION
2 2.0V 20 s/div
7 50.0V 20 s/div
12 PB 100mV 1ms/div
DEFLECTION
3 0.5V 5ms/div
10.0V 5ms/div
13 PB 50mV 0.5ms/div
TV POWER
4 200mV 20 s/div
9 20.0V 0.1ms/div
14 PB 0.5V 20 s/div
CRT
5 50.0V 20 s/div
10 0.5V 5 s/div
NOTE: The following waveforms were measured at the point of the corresponding balloon number in the schematic diagram.
J-1
WAVEFORMS
21 PB 1.0V 0.5ms/div
22 PB 1.0V 5ms/div
23 PB 1.0V 5ms/div
MICON
IN/OUT
19 PB 1.0V 10ms/div
20 PB 0.5V 0.5ms/div
NOTE: The following waveforms were measured at the point of the corresponding balloon number in the schematic diagram.
J-2
WAVEFORMS
CHROMA/IF SOUND AMP
J-3
201
201
211
J801
109
203 129
145 132
211 211
114
218
217 112
111
217
139 L503
132
110
214
112
FB401
215
205
111
137
SP302 216
213 113
208
128
144 216
118
127
B
123 120 216 216
131
216
117
119
216
124
141
104
207
115 134
219
115 A
212
206
133
220
TU601
202
B 135
K1-2
K1-3
367
503
515
300
505 505
M2003
505 335 UN4001 319 313
507 334
AA
508 314
H5001 501 305 356 310 313 304 508 347 301
336
512
A
512 315 338
AB AA AA AB
317
AA
316
361
303
329
AD
320 353
AA 502
M101
366
351 364
308 358
BA 366
AD
AA 370 509
AD
AD
AD
363
AD
351 362
323
AD AD
360
324
511
352
CLASS GREASE
PART NO.
MARK
G-555G G-488M
FL-721 MG-33
AA
AB AC AD
NOTE: Applying positions AA, AB, AC, AD and BA for the grease or oil are displayed for this section. Check if the correct grease or oil is applied for each position.
OIL
BA
K2-1
302 300
511 340 514 341 AA AA 510 AA 322 350 330 AA AA 342 AA 343 511 339 345 503
M2001 AA AA
513 307
AD
AA AD
AA
AC AB
312
BA AA
AD
337
504
CLASS GREASE
MARK AA AB AC AD BA
NOTE: Applying positions AA, AB, AC, AD and BA for the grease or oil are displayed for this section. Check if the correct grease or oil is applied for each position.
OIL
K2-2
S5-OA5-000-220 AHC ASS'Y S5-OP2-002-700 BELT,CAPSTAN S5-OP9-007-100 LEVER,REC S5-OP5-000-830 BASE,AC HEAD S5-OP8-003-240 SPR,AC HEAD S5-OA0-003-600 MAIN CHASSIS ASS'Y S5-OA2-000-810 CLUTCH ASS'Y X S5-OA2-000-730 ARM,IDLER ASS'Y S5-OP6-005-530 ARM,S-S BRAKE S5-OA2-000-760 T REEL ASS'Y S5-OA3-000-610 LOAD ARM S ASS'Y S5-OA3-000-620 LOAD ARM T ASS'Y S5-OA4-001-870 G-ROLLER ASS'Y S5-OA4-001-880 BASE,INCL S ASS'Y S5-OA4-001-960 BASE,INCL T(S) ASS'Y S5-OA4-001-970 P5-3 ARM ASS'Y S5-OA4-002-050 PINCH ROLLER BLOCK S5-OA4-001-750 TENSION ARM ASS'Y S5-OA4-001-760 TENSION BAND ASS'Y S5-OA4-001-780 PINCH ROLLER LEVER ASS'Y S5-OA6-001-820 BRAKE T ASS'Y S5-OA6-001-830 CAP BRAKE ARM ASS'Y S5-OA9-002-130 LINK ASS'Y S5-OA9-002-160 LINK LEVER ASS'Y S5-OP2-002-610 LEVER,CLUTCH S5-OP2-002-620 RING,CLUTCH S5-OP2-002-630 GEAR,CLUTCH S5-OP2-002-710 REEL,S S5-OP2-002-730 STOPPER,REEL S S5-OP2-002-740 SPACER,LINK LEVER S5-OP3-001-780 GEAR,MAIN LOADING S5-OP3-001-790 GEAR,LOADING S S5-OP3-001-800 GEAR,LOADING T S5-OP3-001-860 HOLDER,LOADING GEAR S5-OP4-004-720 ADJUST,TENSION S5-OP4-004-920 HOLDER,TENSION S5-OP4-004-900 LEVER,TENSION S5-OP4-004-750 COVER,P4 S5-OP6-005-430 GEAR,JOINT S5-OP6-005-440 GEAR,MIDDLE S5-OP6-005-450 CAM,MAIN S5-OP6-005-460 CAM,P5 S5-OP6-005-650 CAM,PINCH ROLLER S5-OP6-005-480 ROD,MAIN S5-OP7-000-350 REFLECTOR,LED S5-OP8-003-180 SPR,LOADING GEAR S5-OP8-003-190 SPR,P5 S5-OP8-003-210 SPR,BRAKE T S5-OP8-003-220 SPR,TENSION S5-OP8-003-230 SPR,CAP BRAKE S5-OP8-003-420 SPRING,LOCKER(S) S5-OP8-003-260 SPR,LINK S5-OP8-003-280 SPR,DAMPER S5-OP8-003-300 SPR,RING S5-OP8-003-320 SPR,S-S BRAKE S5-OP9-006-800 OPENER,CASS S5-OP9-006-830 CASS SIDE L S5-OP9-006-840 CASS SIDE R S5-OP9-007-090 TAPE GUIDE L(P,R)
S5-OP6-005-630 BRACKET,MOTOR S5-OP6-005-410 WORM 87-654-075-410 S1-072-268-040 87-743-073-010 87-743-073-410 S1-0A1-268-040 S1-0B1-264-040 87-261-035-410 87-261-032-410 87-258-091-010 S2-Q31-54C-5N0 S2-P26-600-5N0 S2-Q26-471-3N0 S2-P18-450-5N0 S3-ETW-300-000 S1-0A1-235-040 ------S5-23D-910-340 S5-43D-020-130 S5-96P-780-010 S5-94J-980-080 S5-89V-110-070 ---S0-007-003-200 S0-007-003-200 S5-500-2A5-000 SCREW,TAP 2.6-10 VT2+2.6-8 VT2+2.6-6 SCREW,TAP 2.6-6 SCREW,WASHER(A)M2.6-8 SCREW,WASHER(B)M2.6-4 SCREW,PAN M2-6 SCREW,PAN M2-3 U+M3-3 PW,3.1-5.4-0.25 PW(CUT)2.6-6-0.5 PW 2.6-4.7-0.13 PW(CUT)1.8-4.5-0.5 E-RING 3 SEMS A M2.3-5 CONN,PWB SIDE CONN,PWB SIDE 173979-2 HEAD,AC HEAD,FE MOTOR(LOADING) CAPSTAN DD UNIT EP15BC MICRO MOTOR DECK PCB ASS'Y VE8851 PHOTO,TR RPT-38PB113 PHOTO,TR RPT-38PB113 CYLINDER UNIT ASS'Y A55002A500
K2-3
K3-1
REF.NO.
PART NO.
! TU601
S1-45K-000-500
CORD,CONN CH01005A CORD,CONN CH2A014A CORD,CONN CH2B027A CORD CONN CH25080A CORD,CONN CH22071A CORD CONN CH22076A OPERATION PCB ASS'Y *** CAPACITORS ***
COIL,15UH COIL,0.56UH COIL,100UH COIL,100UH COIL,100UH COIL,V IFT COIL,100UH COIL,47UH COIL,27UH COIL,2.2UH COIL,TRAP 2623003 COIL,100UH COIL,BIAS OSC COIL,100UH COIL,100UH COIL,100UH COIL,56UH COIL,120UH COIL,100UH COIL,100UH COIL,100UH COIL,68UH COIL,100UH COIL,100UH *** JACK ***
B701 L004
S2-4AT-036-550 S2-A6A-8A0-A10
! J351 J701
S6-021-310-120 S6-021-010-200
J4201
S6-3P0-000-640
SW750 SW751 SW791 SW792 SW793 SW794 SW795 SW796 SW797 SW798 SW799
S5-042-01T-310 S5-042-01T-310 S5-042-01T-310 S5-042-01T-310 S5-042-01T-310 S5-042-01T-310 S5-042-01T-310 S5-042-01T-310 S5-042-01T-310 S5-042-01T-310 S5-042-01T-310
SW,TACT SKHVBED10 SW,TACT SKHVBED10 SW,TACT SKHVBED10 SW,TACT SKHVBED10 SW,TACT SKHVBED10 SW,TACT SKHVBED10 SW,TACT SKHVBED10 SW,TACT SKHVBED10 SW,TACT SKHVBED10 SW,TACT SKHVBED10 SW,TACT SKHVBED10 *** OTHERS ***
SW1001 S5-082-210-010
SW,LEAF *** CONNECTORS *** CD351 CD750 OS753 S6-CH2-708-6A0 S6-CH2-B02-6A0 S7-7Q0-000-170 CORD,CONN CH27086A CORD,CONN CH2B026A REMOTE RECEIV MAIN PCB ASS'Y *** RESISTORS *** ! ! ! ! ! ! ! ! ! ! ! R439 R440 R441 R442 R443 R444 R447 R448 R449 R450 R501 S4-X5T-422-3F0 S4-X5T-482-2F0 87-025-571-080 87-025-459-080 87-025-297-080 S4-X5T-422-3F0 87-A00-100-060 SF-F01-02J-B10 S5-X2C-E68-2J0 S6-558-14R-7J0 S5-X2C-E1R-2J0 RES,MF 22K-1/4W RES,M 8.2K-1/4W RES,M 100K-1/4W RES,M 15K-1/4W RES,M/F 4.7K-1/4W RES,MF 22K-1/4W RES,FUSE 68-1/2W RES,M 1K-1W RES,CEMENT 6.8K-7W RES,FUSE 4.7-1W RES,CEMENT 1.2-7W
CONN PWB SIDE CONN,PWB SIDE CONN,PWB SIDE CONN PWB SIDE CONN,PWB SIDE 52045-0545 CONN,52045-0445 CONN PWB SIDE CONN *** FILTER ***
CF601
S0-2E2-45R-710
FLTR,SAW M1958M
*** CRYSTAL & CERAMIC OSCILLATORS *** X604 X1001 X1002 X4001 S0-0CT-3R5-050 S0-0CT-012-070 S0-0D3-2R8-010 S0-0CT-3R5-040 X'TAL,HC-49/C X'TAL,HC-49/U-S X'TAL,32.768K X'TAL,HC-49/C
K3-2
! ! ! ! !
! ! ! ! !
! ! !
! ! ! ! ! !
Q405 Q406 Q501 Q502 Q503 Q504 Q506 Q507 Q513 Q520 Q521
SC-3T0-227-100 SD-UQ0-259-900 SC-3T0-290-900 SA-3T1-371-A00 SC-300-416-000 89-318-154-080 87-026-464-080 89-309-458-010 SN-YTB-030-010 87-026-464-080 87-026-464-080
TR,2SC2271(D,E)-AE TR,2SD2599 TR,2SC2909 TR,2SA1371 TR,2SC4160-OEC TR,2SC1815Y TR,DTC114TS TR,2SC945(C) TR,DTC114E TR,DTC114TS TR,DTC114TS *** COILS ***
! ! ! ! ! ! ! ! ! ! !
CORE,BEADS CORE,BEADS BL01RN1-A63T6 CORE,BEADS LFP3A-M3R2TA COIL,4.7MH COIL,LINEA ELH5L4112 FILTER,SS28V-15125 TRANS,H DRIVE 305Y002S *** TRANSFORMERS ***
K3-3
K3-4
211, IKENOHATA 1CHOME, TAITO-KU, TOKYO 110, JAPAN TEL:03 (3827) 3111
737004 Printed in Singapore