Академический Документы
Профессиональный Документы
Культура Документы
Introduction
In this practice Packet Tracer Skills Exam, you will: design and implement an addressing scheme to meet stated requirements configure, verify, and troubleshoot connectivity between all devices in the network
Addressing Table
Device Interface Fa0/0 HQ Fa0/1 S2 NetAdmin H1 VLAN1 NIC NIC 10.10.10.65 10.10.10.2 10.10.10.62 Preconfigured (10.10.10.67) 255.255.255.248 255.255.255.192 255.255.255.192 Preconfigured (255.255.255.248) n/a 10.10.10.1 10.10.10.1 Preconfigured (10.10.10.65) Address 10.10.10.1 Subnet Mask 255.255.255.192 Default Gateway n/a
NOTE: The initial network has some errors. To aid in configuring and verifying the devices as well as troubleshooting the existing errors, use a printed version of these instructions to fill in the missing address information in the table during Step 1.
c. Assign the lowest (first) host address in this subnet to the Fa0/0 interface on HQ. d. Assign the second address in this subnet to the VLAN 1 interface on S2. e. Assign the highest (last) host IP address in this subnet to NetAdmin.
b. Configure the two Fast Ethernet interfaces: Configure the router interfaces according to your completed Addressing Table. Configure each interface with a description.
Step 2: Configure HQ. Press RETURN to get started! Router>enable Router#configure terminal Enter configuration commands, one per line. End with CNTL/Z. Router(config)#hostname HQ
HQ(config)#enable secret class HQ(config)#line console 0 HQ(config-line)#password cisco HQ(config-line)#login HQ(config-line)#exit HQ(config)#line vty 0 4 HQ(config-line)#password cisco HQ(config-line)#login HQ(config-line)#exit HQ(config)#banner motd #Unauthorized access is prohibited.# HQ(config)#interface fastEthernet 0/0 HQ(config-if)#ip address 10.10.10.1 255.255.255.192 HQ(config-if)#description LAN1 HQ(config-if)#no shutdown HQ(config-if)# %LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up HQ(config-if)#exit HQ(config)#interface fastEthernet 0/1 HQ(config-if)#ip address 10.10.10.65 255.255.255.248 HQ(config-if)#description LAN2 HQ(config-if)#no shutdown
HQ(config-if)# %LINK-5-CHANGED: Interface FastEthernet0/1, changed state to up %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to up HQ(config)# Step 3: Configure S2 and Verify Connectivity. Switch>enable Switch#configure terminal Enter configuration commands, one per line. End with CNTL/Z. Switch(config)#hostname S2 S2(config)#enable secret class S2(config)#line console 0 S2(config-line)#password cisco S2(config-line)#login S2(config-line)#exit S2(config)#line vty 0 4 S2(config-line)#password cisco S2(config-line)#login S2(config-line)#exit S2(config)#banner motd #Unauthorized access is prohibited.# S2(config)#interface vlan 1 S2(config-if)#ip address 10.10.10.2 255.255.255.192
S2(config-if)#no shutdown S2(config-if)# %LINK-5-CHANGED: Interface Vlan1, changed state to up %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan1, changed state to up S2(config-if)#exit S2(config)#ip default-gateway 10.10.10.1 S2(config)#exit S2# %SYS-5-CONFIG_I: Configured from console by console S2#ping 10.10.10.1 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 10.10.10.1, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 31/34/47 ms