Академический Документы
Профессиональный Документы
Культура Документы
DESCRIPTION
The ENC6800+ and ENS6800+ Encoder and Encoder with Synchronizer are high precision 12 bit digital encoders, supporting both NTSC and PAL-B or NTSC and PAL-M standards. Standard selection is automatic for 525 line NTSC and 625 line PAL standards.
ENC6800+
FEATURES 4Composite Encoder encodes a 4:2:2 digital video into a composite analog signal, supports NTSC, PAL-B, PAL-M 4Automatic selection between NTSC and PAL-M or NTSC and PAL-B standards 412-bit digital internal processing 4Jitter removal 42X over-sampling 4EDH detection 4Vertical Blanking Field/Line/Mode Control 42.5H delay mode or one line synchronizer mode (without synchronizer) 4External NTSC and PAL color black reference inputs 4Output analog video cable pre-equalizer for 300m of Belden 8281 coaxial cable 4Built-in Test Signal Generator with 4 test patterns 4Color black output signal when signal is lost 4Active Video Output with on/off selection (for Japan application) 4SCH color frame at 0 phase 475 ohm jumper selectable termination for Ext. Genlock loop throughs 4Vertical Line Processing option: Line 10 to 23 (NTSC/PALM), Lines 6 to 24 (PAL-B) 4ENS6800+ offers External Timing Reference for compatible audio cards 4User adjustable level controls: Luminance, Chrominance, Black 4Timing Controls: Vertical, Horizontal, Fine SC (from Genlock) 4Cross Color Reduction with 1 line delay 4Outputs internally the TTL level IO-Delay pulse to synchronize the downstream audio processor. 4ENS6800+ offers selectable Frame Synchronizer or Delay Mode 4Test Pattern Generator with 2 patterns: color bars, and modulated ramp 4When switching the standards (NTSC, PAL-M, PAL-B), the settings are shadowed and restored. 4Full control support 4Inputs 4Outputs
Serial digital SMPTE 259M-C, Genlock inputs, NTSC, PAL-B and PAL-M
SDI
SDI
Frame Synchronizer
NTSC/PAL B/M
CPU
ENC6800+ENS6800+
SDI IN
GENLOCK 1
GENLOCK 2
SDI RECLK 1
CMPST 1
CMPST 2
CMPST 3
CMPST 4
SDI IN
Genlock 525
Genlock 625
SDI RLCK
Four composite analog outputs, two re-clocked serial digital video outputs
6800+/6800/7000 Series
Encoder
.
ENC6800+
Specifications and designs are subject to change without notice.
SPECIFICATIONS
SERIAL DIGITAL INPUT VIDEO
Standard Connector Impedance Return Loss Signal Level CMRR Equalization
SMPTE 259M-C, 270Mb/s, 525/625 component BNC per IEC169-8 75 Ohm >18 dB to clock frequency 800mV 10% 30Vp-p, up to 60 Hz Automatic up to: >23dB, 259M-C typ. SMPTE 259M-C, 270Mb/s, 525/625 component BNC per IEC169-8 75 Ohm >18 dB to clock frequency 800mV 10% 0V 0.5V Up to 250m (Belden 8281)
Standards NTSC, PAL-B, PAL-M Impedance 75 Ohm Return Loss > 40dB to 5.75 MHz Quantizing 12 bits Frequency Response 0.15dB to 5.5 MHz Differential gain < 1 % (typically < 0.5 %) Differential phase < 1 deg. (typically < 0.5 deg.) DC offset 5mV Note: Should be factory calibrated to 0V. Chroma/Luma delay < 1.5ns Chroma/Luma gain 1.5% Transient Response < 0.5% K Factor Line Time Distribution 0.10% Luma Non-linearity < 0.2% Signal to Noise > 60dB rms with bandwidth 10kHz to full Adjustable vertical blanking 10-21 lines for NTSC for both fields (Field 2: 272~283) 6-23 lines for PAL for both fields (Field 2: 318~335)
ORDERING INFORMATION
ENC6800+ ENC6800+S ENC6800+D ENC6800+SR ENC6800+DR
Encoder, Module Only Encoder + Single Rear Connector Encoder + Double Rear Connector Rear connector only, Single Rear connector only, Double
6800+/6800/7000 Series