Академический Документы
Профессиональный Документы
Культура Документы
FEATURES
*High input sensitivity Typ.30dB. *Key and peak controllable AGC. *Operating voltage down to 7V. *Wide video bandwidth suitable for modulation IF of 4.5, 5.5,6.0,6.5 MHZ. *Differential input implied with easy used with SAW *Low external part count.
DIP-14H
BLOCK DIAGRAM
Rf?AGC voltage regulator AGC Key time control constant pulse input 4 2
RF?AGC to tuner 6
IF power
Vcc 7
12
RF AGC
IF AGC
Noise reduction
Video output
3 Video output
IF amplifier
10 Cap
11
14
13 GND
Detector coil
UTC
QW-R111-003,A
SYMBOL
VCC IP-P PD TOPR TSTG
VALUE
15 3 875(Ta=75C)With heat sink -20 ~ +70 -40 ~ +125
UNIT
V VP-P W C C
ELECTRICAL CHARACTERISTICS(Ta=25C,VCC=12V,fP=38MHZ,fm=400HZ)
PARAMETER
Total Supply Current Input Sensitivity Max Input Voltage Video Output Voltage Video Output DC Voltage S/N Ratio RF AGC Voltage(Hi) RF AGC Voltage(Lo) Differential Gain Differential Phase Video Detector Bandwidth Input Impedance Input Capacitance
SYMBOL
ICC SVI VI(MAX) VO VO(DC) S/N V6H V6L D.G. D.P. GV(F) RIN CIN
TEST CONDITIONS
I7+I12,RA=150 Modulation=80%, VO=1.4VP-P Modulation=80%,-1dB Modulation=80%,VI=3mVrms No signal Modulation=80%-0%, VI=3mVrms V5=0V V5=7V Step signal,fM=4.43MHZ Step signal,fM=4.43MHZ -3dB point
MIN
40
TYP
50 30
MAX
60 35
UNIT
mA dB dB
100 1.0 3.3 40 8 1.4 3.8 50 9 0 11 0.5 10 10 5.5 1.5 3.3 1.7 4.3
UTC
QW-R111-003,A
12pF
0.01 F
56
680
RF AGC
IF AGC
6.8k
180
Noise reduction
saw filter
222 F 120
222 F
Input
22pF
IF amplifier
Video Amplifier
Detector coil
1.5k
9
0.01 F
10
0.01 F
11
0.01 F
12
47 F
13
14
222 F
150
TEST CIRCUIT
Vcc 12V 0.01 F 0.22 F 470k SW3 AGC 10k B 0.01 F 0.01 F 150 47F 47 F 100 1k A B
V
A B
IDS
A 1k 6.8k
0.01 F
Video output
12
UTC PC1366
8
0.01 F 0.01 F
10
F 0.01
11
F 0.01
1
600
14
13
22pF
38MHz
Detector coil
UTC
QW-R111-003,A
80 70 60 50 40 30 20 10 0 0 5 10 15 20 fp=38MHz,fm=400MHz MOD=80%,Ra=150
-5
-10
-15 0.01
0.1
1.0
10.0
100.0
Frequency (MHz)
S/N ratio(dB)
20
1.6
fp=38MHz,fm=400MHz MOD=80%,Ra=150
30
40
1.2
0.8
50
0.4 0 0 20 40 60
60
80
100
12
16
20
UTC assumes no responsibility for equipment failures that result from using products at values that exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges, or other parameters) listed in products specifications of any and all UTC products described or contained herein. UTC products are not designed for use in life support appliances, devices or systems where malfunction of these products can be reasonably expected to result in personal injury. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner. The information presented in this document does not form part of any quotation or contract, is believed to be accurate and reliable and may be changed without notice.
UTC
QW-R111-003,A
This datasheet has been downloaded from: www.DatasheetCatalog.com Datasheets for electronic components.