Академический Документы
Профессиональный Документы
Культура Документы
MAINTENANCE MANUAL
CATALOG CHAPTER1 Safety and notes ........................................................................................................2 1-1 Installation notes.............................................................................................................2 1-2 Attention points of operation and using .......................................................................2 1-3 Storage notes ..................................................................................................................2 1-4 Dismantling notes ...........................................................................................................2 1-5 High-voltage warning ....................................................................................................2 CHAPTER2 Whole machine standard and terminal functions...............................................2 2-1 Basic standards : ...............................................................................................................3 2-2 Introduction of terminals(practicality photos)...............................................................3 CHAPTER3 Main chip functions and brife introductions of power supply...........................4 3-1 Main chips and functions of LS07 chassis ...................................................................4 3-2 Pin function description of LS07 chips ...........................................................................6 3-3 Brief introduction of power supply 11 CHAPTER4 The chasis frame diagram,mainboard power supply system, mainboard interfac -e definition and the waveform of key points ...12 4-1 The chassis frame diagram...........12 4-2 Power supply system...13 4.3 The waveform of key points16 CHAPTER5 Software upgrade tooling,software upgrade instrutions,software initialization, parameter selection,software initialization,software version and the screen matching instruction ...16 5-1 Software upgrade tooling . 16 5-2 Software upgrade instrutions.. 17 5-3 Software initialization.. 18 5-4 Parameter selection........................................... ...19 5-5 Software version...........................................................................................................20 5-6 The screen matching instructions...............................................................................20 CHAPTER6 Classical accident maintenance procedures and examples ..............................20 6-1 The thinking of do not boot............................................................................................21 6-2 Common problems for reference ................................................................................21 CHAPTER7 High voltage and high electric current wearing parts list................................21 CHAPTER8 Factory mode parameter setting instructions and notes ...............................22 8-1 Enter into the factory mode ........................................................................................22 8-2 Setting method of factory menu..............25 CHAPTER9 Simple debugging specification of the machine... ......25 9-1 Clear EEPROM,and set the parameters after upgrading according to the upgrade instr -uctions ....25 9-2Check each channel/source to see if the image and sound are normal...25 Appendix:LS07 chassis circuit schematic...........................................................26
item visual area aspect ratio resolving ratio visual area H x V display colour LCD Panel contrast brightness visual angle react time backlight life colour temperature TV function sound system olour system AV1 AV2 aberration signal audio and video HDMI signal input PC input
standard 18.5 inches opposite angles (BOE) 16:9 1366 x768 409.8m m (H) 230.4m m (V) 16.7 million 1000 250cd/m2 170(horizontal)/ 170 (vertical) 5ms 50000 hours cold/hot B/GD/KIM PAL / SECAM / NTSC RCA x 1 S-Video x 1 YPbPr x 1 HDMI x1 plug and use input frequency recommend H: 31.5K -50KHz V: 60Hz to 75Hz 1024x768(60HZ) outputTV and AV signal ,Audio L/R x1 two 5W innerput speakers ear phone AC100V~240V, 50/60Hz <60W - 5 / + 20 / 35 + 0 ~ + 40 - 25 ~ + 60 10% ~ 85% Kg the parameters are for reference only,the specific should accord to the standard of the screen practicality of the batch orders
Videooutput Audio Power Panel rotation requirement for circumustance appearance size net weight
outputCVBS signal Audio output L / R power supply power disipation Front/back/rotation operation temperature storage temperature operation humidity WxHxD no accessory
2-2
S input
YpbPr input
ATTENTION: 1. HDMIand YpbPr suppot to 1080P 2.The recommendation resolving ratio of VGA is 1024X768 3.Both AV and S terminal use audio signal to output. 4. Av output supports Tv input /AV outputAv input /AV outputS input /AVoutput
DC switch
storage
flash
tuner
no. 1 2 3 4 5 6 7 8
main function Tuner, output sound IF and video signal Processor with Video Decoder EEPROM Flash deposit,the control program of the whole machine is in it DC switch sound meter sound meter Audio amplifier
3-2 Pin function description of LS07 chip 3-2-1. TSUMV26KEProcessor chip with Video signalTSUMV26KE
The following tables are the specific distribution of pin function Table1:Related pin function distribution of the machine interface unit
Table2:
Related
pin
function
distribution
of
the
analog
interface
Table3:Related pin function distribution of the analog audio signal input and output
3-2-2: Pin function of TAF6-C2I21VH tuner No. 1 2 3 4 5 6 7 8 9 10 11 Terminal AGC NC GND SCL SDA 5VB 5VB ADC/NC +33V NC IF1 name Description AGC voltage supply No Connected Address-select line Assemble line(clock) Assemble line(data) 5V Power supply 5V Power supply Analog data Connected No Connected IF Output conversion/ No
10
Pin No. 1 2 3 4 5 6 7 8
I/O I O I
Function Chip Select Input Data Output White Protect input Ground
I/O I I
3-2-2:AO4803pin function Dual-channel enhanced MOSFET pin 1 2 3 4 5,6 7,8 sign S2 G2 S1 G1 D1 D2 function description source2 gate2 source1 gate2 drain1 drain2
11
GND
ACinput AC100-240V
GND 5V 5V
Chapter4: The chassis frame diagram, mainboard power supply systems, mainboard interface definition and the waveform of key points
This chapter mainly introduce the chassis frame diagram,power supply system,interface definition and each key points wave shape. 4-1 The chassis frame diagram
12
4-2 Power supply system Powe board has two kinds of output voltage:+12and+5 4-2-1.the logic relation diagram of main board power L31 R126 40V 33V,RFH(high PWwave surge U20 DVD 12V supply power +12V R138 +12V_IN power CON14 PIN 56 R114 +12_INA U1 L2 AVDD MPLL U20 +5V_1 power JP3 PIN34 reset circuit power supply VDD PM +5V_2 L32 L18 U17 Screen eletricit +3.3V_2 VDDP supply power L4 AVDDA supply power AVDD AV supply power key press supply power Remote controller receiver board supply remote controller light supply power +3.3_STB TDA1517 12Vsupply power
frequency
head)
supply
U3
R214 CON12,PIN1.2
1.26V 3.3V
5V
5V
3.3V
U20 5V,12V
U3 3.3V
U4 1.26V
U19 5V
U17 5V
U1 3.3V
4-2-3Interface definition
14
SAR1,SAR0,GND
GND GND 5V 5V
15
Chapter5: Software upgrade tooling,software upgrade instrutions ,parameter setting,software initialization,software version and screen matching instructions
5-1 Software upgarde tooling---there are two kinds of using upgrade tooling 1.Use the combined interface(the parallel port) upgrade tooling:use the upgrade programme: ISP_Tool V4.0.5.exe and higher versions 2.Use interface upgrade tooling,use the upgrade programme: versions higher than ISP Tool V4.3exe Combined interface or USB VGA
computer
upgrade tooling
LCD TV
16
5-2 Software upgrade instrutions 1.Connect the upgrade tooling well,then operate the upgrade programme
Cancel the selection in the red line frame of last picture,as following shows:
2.Select(connect)first,if normal,system will feedback the flash style of the machine chassisAs following
17
4.Select(auto),enter the programme writing period,you only need to press(run),you will be able to write programme. 5-3 Software initialization Afrter finishing the software upgrading,enter into the factory menu,select CLEAR EEPROMclear EEPROM.
18
The system will go into standby automatically after clearing EEPROM. 5-4 Parameter selection After clearing EEPROM,you need to do some parameter selection works,for example: 5-4-1.Enter the system setting,,as the following picture.Select SYSTEM SETTING to enter:
19
Usually,items in the red frame need to debugt,but not everyone,the specific debugging should satisfy the actual requirements of the batch orders. 5-5 Software version Related programme information can be read from the software version,which is convenient for professors to know the software states.
20
do not boot
if
the
no image
no sound
black screen
check if there is signal entering into the main chip of each source
check
the
backlight voltage
check the screen and the check the circuit related to the mainboard change the screen or examine the mainboard mainboard crossly
6-2 Common problems for your reference: To speed you to dignose and solve problems,the following commom problems are offered for your reference Symptoms No picture, no sound, and no indicator light on Possible Reason 1.The power cord is not plugged in 2.The power is off Solutions 1.Plug in the power cord 2.Turn the power on
21
1.Contrast, sharpness, and color are set improperly 2.Color system is improperly 3.Sound system is improperly Signal source is low-grade or the signal cord is in a lower quality Contrast, brightness, color and volume are all in the minimum value or TV is in mute mode. The signal cable is not correctly connected. There is no signal input or the video cable is not connected or incorrectly connected
1.Adjust the numberical value of Contrast, sharpness, and color 2.Set the Color system to the country broadcasting standard 3.Set the Sound system to meet the countrys broadcasting standard Use the qualified signal cord Adjust the value of contrast, brightness, color and volume Connect correctly Connect correctly the the signal video cable cable
Picture is spotted or with snow No picture, no sound and indicator light is green
Blue screen, AV or SVIDEO is displayed Picture is unclear or shaking or with black horizontal strips (in VGA mode) VGA picture is not centered No sound VGA picture display with improper color HDMI source, with snow pixel of full screen
VGA picture is not correctly adjusted. There is no audio signal input or audio cable is not connected correctly The color temp is adjusted incorrectly by user The signal source is not normal
Enter SETUP menu, select Auto Tracking item to perform automatic calibration and adjust Phase to solve the problem Connect correctly the audio cable
Readjust the color temp, or select the original color setting Plug the HDMI cable again 1. Make sure the positive and the negative polarities are correct. 2.Check if there is a loose contact between the batteries and the springs 3.Replace the batteries
Number
Name
Model number
1. 2. 3.
Main Board
JUG6.690.664-02
22
4. 5. 6. 7. 8. 9.
5 0.1 0.5 2 1 1
ADC adjustment
PICTURE MODE
Picture mode
key
COLOR TEM
key
Switch thethree state NORMAL WARMCOLDat each source Switch the four state THEATER MUSIC USER NEWSat each source
SOUND MODE EEPROM ADJUST NON LINEAR MULTI-LANGUAGE OTHER OPTION SSC SETTING FACTORY IR
key
SOURCE Input switch key Select input signal (2) Use the key / on remote control to select items that need to adjust, use the key / to adjust them. Submenu content SYSTEM SETTING
23
adjust item LANGUAGE POWER MODE LOGO EQUALIZER USB DVD TUNER INPUTTYPE IRTYPE AUDIOTYPE H-OVERSCAN V-OVERSCAN H-CAPTION V-CAPTION TURNOFFPANEL DEBUG ENABLE TTX-MTS ENABLE PICTURE MODE adjust item SOURCE PICTURE MODE CONTRAST BRIGHTNESS SATURATION SHARPNESS COLOR TEMP adjust item SOURCE COLOR TEMP R G B OFFSET R OFFSET G OFFSET B SOUND MODE adjust item SOURCE adjust value TV
adjust value boot mode OFF OFF OFF OFF TAF6C2121VH 1A1S G6C52R 2X2W 51 30 135 130 OFF ON ON
remark OSDlanguage selectION once,twice boot mode switch LOGO switch USB switch DVDswitch switch of radio frequency head(RFH) select input terminal select select the remote control model select the output power of speaker horizontal overscan vertical overscan horizontal center vertical center switch of the screen when change channel or source
remark reveal the present signal source select the picture mode to adjust no need of adjustment no need of adjustment no need of adjustment no need of adjustment
remark display the present signal source no need of adjustment no need of adjustment no need of adjustment no need of adjustment no need of adjustment no need of adjustment no need of adjustment
SOUND MODE BASS TREBLE 120HZ 500HZ 1500HZ 5KHZ 10KHZ AVC LEVEL PRESCALE NON LINEAR adjust item VOLUME BASS TREBLE CONTRAST BRIGHTNESS SHARPNESS SATURATION
select the sound mode no need of adjustment no need of adjustment no need of adjustment no need of adjustment no need of adjustment no need of adjustment no need of adjustment
remark no need of adjustment no need of adjustment no need of adjustment no need of adjustment no need of adjustment no need of adjustment no need of adjustment
8-2 Setting method of factory menu Seledt the setting item Operators can choose setting item with P+ and P- key, font with background display means the item has been chosen. PressV+key to enter sub directory. Use P+and P-keys on remote control to select up and down, then useV+andV-keys to set. (2)Most of the menu functions are open under factory mode, if need,item checking and effect test can be done by using menu . (3) TV signal switching can be done by directly pressing the number keys in factory mode .PressMENUto back to the parental catalog,pressEXIT to quit factory mode.
25
26
27
28
29
30
31
32