Вы находитесь на странице: 1из 4
 
Fast-Setting Clear Adhesive
IntroductionSuggested UsesFormula
 This adhesive is a rapid curing, unfilled epoxy/amine adhesive possessing light color. Thinbond line sections will set to handling strength in approximately one hour at room tempera-ture and will develop 1,000 psi tensile shear strength in approximately two hours. Practical
cure rates are achieved at temperatures as low as 4 °C. A mild, non-offensive odor and non-
fuming characteristics are other features. Tube adhesives Transparent glass adhesivesRapid repair kitsMedium set traffic button adhesives (unfilled modifications)
MaterialPoundsGallonsResin Portion
EPON
Resin 828100.0 10.31
Total Resin Portion100.010.31Converter Portion
EPI-CURE
Curing Agent 3270 95.0011.99EPI-CURE
Curing Agent 32535.000.62
Total Converter Portion100.0012.61
*Formerly 991-98.
starting
SC:2061-01
EPIKOTE
EPON
EPI-CURE
EPI-REZ
HELOXY
CARDURA
VEOVA
formulation
EPON
Resin 828 with EPI-CURE
Curing Agents 3270 and 3253
No. 4030
*
 
SC:2061-01 / Starting Formulation No.4030Page 2
 Table 1/
Handling properties
Resin/converter combining ratio
By weight1:1By volume1:1:3
Viscosity at 25 °C,
cPResin portion12,000Converter portion4,500
Pounds per gallon,
combined system8.73
Gel time at 25 °C,
minutes100 grams50.005-inch film60
 Table 2/
Adhesive properties
Cure scheduleTensile shear strength,
psi
1
Hours,
at 25 °C1.00301.251601.505201.751,0802.001,4722.502,300
Weeks,
at 25 °C23,200
Postcure,
at 149 °C20 minutes3,200
1
Based on aluminum to aluminum lap shear specimens per ASTM D-1002.
 Table 3/
Effect of water immersion on tensile shear strength
WaterTemperature
25 °C25 °C25 °C66 °C66 °C
TestTemperature
25 °C25 °C25 °C25 °C25 °C
psi
2,3002,3002,3002,1001,300
DaysImmersion
030903090
 
SC:2061-01 / Starting Formulation No.4030Page 3
CompoundingInstructionsApplication Instructions
Weight EPI-CURE
Curing Agent 3270 and EPI-CURE Curing Agent 3253 into a mixing vessel
and blend with low speed agitation until homogeneous. Package in tightly sealed containers
of steel, aluminum, polyeolefin or glass.
All substrates to be bonded should be free of dirt, grease, oil, or other contaminants.
 Thoroughly mix equal parts by weight of the resin and converter. Apply adhesive to both
surfaces to be bonded. Contact pressure is sufficient for development of maximum strength.
 These are starting point formulations and are not proven for use in the user’s particular
application but are simply meant to demonstrate the efficacy of the products and to assist
in the development of the user’s own formulations. It is the user’s responsibility to fully test
and qualify the formulation, along with the ingredients, methods, applications, or equip-
ment identified herein (“Information”), by the users knowledgeable formulator or scientist,
and to determine the appropriate use conditions and legal restrictions, prior to use of
any Information.

Вознаградите свое любопытство

Все, что вы хотели прочитать.
Когда угодно. Где угодно. На любом устройстве.
Без обязательств. Отменить можно в любой момент.
576648e32a3d8b82ca71961b7a986505