Академический Документы
Профессиональный Документы
Культура Документы
CRCO lip seal option CURE secondary seal option ANSI+ gland options Selfaligning faces Flush, quench and drain ports
www.aesseal.com
Flexibility
There are seven modular face combinations in the range comprising: Carbon/Ceramic; Carbon/Solid Tungsten Carbide (TC); Carbon/Silicon Carbide (SiC); Carbon/Chrome Oxide and hard face options comprising: TC/TC; TC/SiC and SiC/SiC. The benet in the CURC, CRCO and CURE design is extended mechanical seal life as the correct face combination can be selected for each individual application.
Cartridge Construction
Cartridge seal construction is a proven reliability improvement. Seals preassembled at the factory, pressure tested and shipped as a unit dramatically increase performance as errors due to incorrect installation decline. It is no longer necessary to measure and set spring compression as assembled seals mean that faces are protected from damage during installation.
Design features
Single Seals with Environmental Control Options
General service applications are eciently sealed with an O ring mounted, balanced, selfaligning seal. The SAI, CS, USI and NSI component seals and the SCUSI and Convertor IIcartridge seals eectively seal all general service applications. At the other end of the application spectrum, hazardous and dangerous products demand an engineered sealing approach. Double seals with closedloop convection tank systems provide the necessary backup protection. Between these application extremes lie nonlubricating and/or nonhazardous uids that alter their state with environmental changes. A single seal, with an API type gland, provides temperature control and protection from atmospheric contact for these applications. *This gland derivation comes from the American Petroleum Institute(API) specication. Secondary uids introduced through the Quench and Drain ports to the atmospheric side of the seal faces, control the environment without dilution of the process uid. Water, steam, grease, oil and other suitable barrier uids can be used. *A version of the CURC can be supplied, with a fully machined gland, which conforms to the dimensional requirements of API 682. These can be used on applications where qualication tested, fully API 682 compliant seals are not required.
CURC Showing Quench & Drain Ports
2D-Axisymmetric Finite Element Analysis review showing atness of the seal face after shrink t under dierent thermal and pressure conditions.
CURC Range
Sizes available: 1.000 - 5.000 (24mm - 125mm)
I J Flush, Quench & Drain Ports 1/4 NPT G MIN C D G MAX
16 19 17
1 A F
11
13
18
10
12 H MAX
14 15
B E
Item
1 2 3 4 5 6 7 8 9 10
Description
Rotary O Ring Sleeve O Ring Cartridge Sleeve Springs Rotating Drive Pins Rotating Face Stationary Face Stationary O Ring Universal Pivot Ring Gland Pins
Material
Viton / EPR / Kalrez / Aas Viton / EPR / Kalrez / Aas 316L Stainless Steel Alloy 276 Stainless Steel 316L SS - Carbon / TC / SiC* SiC / Ceramic** / TC Viton / EPR / Kalrez / Aas 316L Stainless Steel Stainless Steel
Item
11 12 13 14 15 16 17 18 19
Description
Gland R'Bush O Ring Restriction Bushing Clamp Ring Drive Screws Clip Screws Radial Setting Clips Anti-Tamper Screws Gasket
Material
316 Stainless Steel Viton / EPR / Kalrez / Aas Carbon 316L Stainless Steel Stainless Steel Stainless Steel Brass Stainless Steel AF1 / GFT
CURC Dimensions
CURC Size Chart (inches)
A 1.000 1.125 1.250 1.375 1.500 1.625 1.750 1.875 2.000 2.000-AC 2.125 2.250 2.375 2.500 2.625 2.750 2.875 3.000 3.125 3.250 3.375 3.500 3.625 3.750 3.875 4.000 4.125 4.250 4.375 4.500 4.625 4.750 4.875 5.000 B 4.125 4.250 4.375 4.375 5.000 5.000 5.500 5.500 6.000 5.250 6.000 6.500 6.500 7.000 7.000 7.000 7.500 7.500 7.500 8.000 8.000 8.000 8.500 8.500 8.500 9.000 9.000 9.000 9.500 9.500 10.000 10.000 10.000 10.000 C 2.125 2.250 2.375 2.500 2.812 2.812 3.187 3.187 3.562 3.450 3.562 3.812 3.812 4.312 4.312 4.312 4.937 4.937 4.937 5.312 5.312 5.312 5.937 5.937 5.937 6.625 6.625 6.625 7.000 7.000 7.345 7.345 7.345 7.345 D 1.937 2.063 2.187 2.312 2.562 2.562 2.812 2.812 3.063 3.035 3.063 3.312 3.312 3.812 3.812 3.812 4.250 4.250 4.250 4.625 4.625 4.625 5.000 5.000 5.000 5.375 5.375 5.375 5.750 5.750 6.125 6.125 6.125 6.125 E 0.519 0.519 0.519 0.519 0.644 0.644 0.644 0.644 0.644 0.644 0.644 0.644 0.644 0.769 0.769 0.769 0.769 0.769 0.769 0.769 0.769 0.769 0.769 0.769 0.769 0.769 0.769 0.769 0.769 0.769 0.769 0.769 0.769 0.769 Fmin 1.625 1.750 1.875 2.000 2.250 2.375 2.500 2.625 2.750 2.750 2.875 3.000 3.125 3.375 3.500 3.625 3.750 3.875 4.000 4.125 4.250 4.375 4.500 4.625 4.750 4.875 5.125 5.125 5.375 5.375 5.625 5.625 5.875 5.875 Fmax 1.937 2.062 2.187 2.250 2.375 2.500 2.750 2.875 3.000 3.000 3.125 3.250 3.375 3.625 3.750 3.875 4.125 4.250 4.375 4.500 4.625 4.750 5.000 5.125 5.250 5.500 5.875 5.875 6.250 6.250 6.625 6.625 6.625 6.625 Gmin 2.687 2.812 2.937 3.062 3.375 3.375 3.750 3.750 4.125 4.000 4.125 4.500 4.500 5.000 5.000 5.000 5.625 5.625 5.625 6.125 6.125 6.125 6.750 6.750 6.750 7.437 7.437 7.437 7.812 7.812 8.312 8.312 8.312 8.312 Gmax 3.562 3.687 3.812 3.812 4.437 4.437 4.937 4.937 5.437 4.750 5.437 5.812 5.812 6.312 6.312 6.312 6.812 6.812 6.812 7.187 7.187 7.187 7.687 7.687 7.687 8.187 8.187 8.187 8.687 8.687 9.062 9.062 9.062 9.062 Hmax 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 5/8 5/8 5/8 5/8 5/8 5/8 5/8 5/8 3/4 3/4 3/4 3/4 3/4 3/4 3/4 3/4 3/4 3/4 3/4 7/8 7/8 7/8 7/8 I 1.125 1.125 1.125 1.125 1.125 1.125 1.125 1.125 1.125 1.125 1.125 1.125 1.125 1.250 1.250 1.250 1.250 1.250 1.250 1.250 1.250 1.250 1.250 1.250 1.250 1.250 1.250 1.250 1.250 1.250 1.250 1.250 1.250 1.250 J 1.590 1.590 1.590 1.590 1.752 1.752 1.752 1.752 1.752 1.752 1.752 1.752 1.752 1.877 1.877 1.877 1.877 1.877 1.877 1.877 1.877 1.877 1.877 1.877 1.877 1.877 1.877 1.877 1.877 1.877 1.877 1.877 1.877 1.877
Seal sizes from 5.125 to 12.000 are designed to suit specic equipment using modular components. Contact AESSEAL technical department for dimensional information and availability.
For exotic alloy versions, add 0.125 to seal length inboard Note that seal sizes 6.125 and above are supplied without a pivot ring "Factory repair program is available" "Replacement seal kits are available"
Seal sizes from 130mm to 300mm are designed to suit specic equipment using modular components. Contact AESSEAL technical department for dimensional information and availability.
For exotic alloy versions, add 3 to seal length inboard Note that seal sizes 6.125 and above are supplied without a pivot ring "Factory repair program is available" "Replacement seal kits are available"
F A
Item
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22
Description
Rotary O Ring Sleeve O Ring Sleeve Springs Rotary Drive Pins (not shown) Rotary Face Stationary Face Stationary O Ring Pivot Ring Gland Pins (not shown) Gland External Stationary Face External Stat O Ring Clamp Ring Drive Screws (not shown) Clip Screws Setting Clips Anti-Tamper Screws (not shown) External Rotary Face External Rotary O Ring Springs Gasket
Material
Viton / EPR / Kalrez / Aas Viton / EPR / Kalrez / Aas 316L Stainless Steel Alloy 276 Stainless Steel 316L SS - Carbon / TC / SiC* SiC / Ceramic** / TC / 316L SS Viton / EPR / Kalrez / Aas 316L Stainless Steel Stainless Steel 316 Stainless Steel Carbon Viton / EPR 316L Stainless Steel Stainless Steel Stainless Steel Brass Stainless Steel 316L SS - Cr.OX Viton / EPR Alloy 276 AF1 / GFT
ITEM 5 is an integral part of ITEM 3 ITEM 10 is an integral part of ITEM 11
16 17
*This material is not available in some sizes above 4.000 (100mm). **Not available in all sizes - contact AESSEAL for more information.
Additional Barrier Fluid Information On processes where leakage of the primary product being sealed cannot be tolerated, the barrier uid pressure should normally be set at 15 psig (1 barg) above the stung box pressure and a CDSA double seal should be used. Where a barrier uid pressure between 10 psig (2/3 of a barg) and 30 psig (2 barg) is required, please contact our Technical Department. Please note however that a higher pressure version of the CURE will not operate eectively at zero gauge pressure, with a very low pressure less than 5 psig (1/3 of a barg), or in a vacuum. The CURE is available in the following sizes: 1.000 - 4.000 (24mm - 100mm).
SWFF-TF
FLOWTRUE
AES-15
PUMPPAC
The systems above are compatible with a wide selection of barrier and buer uid media. They are supplied pre-assembled with all necessary components and ttings. On site inventory costs are reduced by modular system construction.
The CDSA has double pressure balanced rotaries and independent seal face design. It is also available with double or tandem seal protection. Both CURC and CDSA products employ modular components, thereby increasing availability and reducing product lead time. This CDSA brochure is available by contacting the Marketing Department at marketing@aesseal.com or can be downloaded by visiting our website at www.aesseal.com
This document is designed to provide dimensional information and an indication of availability. For further information and safe operating limits contact our technical specialists at the locations below.
Use double mechanical seals with hazardous products. Always take safety precautions: WARNING Guard your equipment Wear protective clothing
UK Sales & Technical advice: AESSEAL plc Mill Close Bradmarsh Business Park Rotherham S60 1BZ United Kingdom Tel: +44 (0) 1709 369966 Fax: +44 (0) 1709 720788 E-mail: seals@aesseal.com
Distributed by:
USA Sales & Technical advice: AESSEAL Inc. 355 Dunavant Drive Rockford TN. 37853 USA Tel: +1 865 531 0192 Fax: +1 865 531 0571 E-mail: usa@aesseal.com
Our purpose is to give our customers such exceptional service that they need never consider alternative sources of supply.
www.aesseal.com
Important: Since the conditions and methods of use of this product are beyond our control, AESSEAL plc expressly disclaims any and all liability resulting or arising from any use of this product or reliance on any information contained in this document - AESSEAL plc standard conditions of sale apply. All sizes are subject to manufacturing tolerances. We reserve the right to modify specications at any time. AESSEAL is a Registered Trademark of AESSEAL plc, AESSEAL plc recognizes all trademarks and trademark names as the property of their owners. LN-UK/US-CURC-01b Copyright 2011 AESSEAL plc 11/2011