Академический Документы
Профессиональный Документы
Культура Документы
U NI SAW Accessories
36-201
Standard & Dado Arbor Nut Assembly
36-055
Feather Board
36-050
Push Stick
36-0101
Table Saw Arbor Wrench
36-0944
Standard Replacement Throat Plate
36-805
Zero Clearance Throat Plate
36-808
Dado Throat Plate
50-479
5 in. to 4 in. Port Reducer
For use with stacked dado cutters Phenolic construction for minimal
tearout
78-967
BIESEMEYER Medium and Thick Kerf Riving Knife
78-965
BIESEMEYER Thin Kerf Riving Knife
34-568
Clamp Attachment
34-928
Deluxe Miter Gauge
U NI SAW Accessories
78-9450
BIESEMEYER Rear Outfeed Table
50-2000 / 50-257
Mobile Base
Adds an additional 4 ft. x 44 in. of work support Compatible with any DELTA UNISAW or other DELTA 12 in. or 14 in. saws
Enhances mobility in the workshop 50-2000 for use with older model UNISAW 50-257 for use with 36-L352 or 36-L552 UNISAW models
78-864B / 78-918B
BIESEMEYER Universal Table Board
78-138B / 78-055B
BIESEMEYER Fence Rails
78-864B For the 36 in. BIESEMEYER Fence System Table Board L X W X H: 37 in. X 35 1/2 in. X 4 1/2 in. 78-918B For the 52 in. BIESEMEYER Fence System Table Board L x W x H: 52 in. x 37 in. x 4 1/2 in.
78-138B For 36 in. BIESEMEYER Fence System 78-055B For 52 in. BIESEMEYER Fence System
Constructed of a hardwood alder frame and laminated particle board Laminate siding on three sides Backer-board underside
Premium Accessories
78-919B
BIESEMEYER Fence System
78-939
BIESEMEYER Cut-off Fence
78-970
BIESEMEYER Standard Accessory Drawer
The most precise fence in the industry Fence body constructed from .083
gauge steel
blades, two riving knives, throat plate, push stick, wrench/ arbor nut and complete guarding assembly
the need for using a hand-held tape to square and set the fence
inch dimension can be easily added when indexing the hairline on your BIESEMEYER fence with the scale on the system ft.s guide
78-940
BIESEMEYER Auxiliary Fence
34-184
Universal Tenoning Jig
Universal miter bar for use with all 3/8 in. x 3/4 in. miter slots
50-786 50-531
4 in. x 20 ft. Hose
50-530
4 in. x 10 ft. Hose
Service Parts
one direction and causes resistance if moved in the other direction; preventing kickback
ServiceNet is the Official Parts & Service Site For DELTA and is your one-stop for all your parts needs.
www.DeltaMachinery.com/parts
STEP 1: Measure the body thickness of the blade. STEP 2: Make a shallow cut in scrap material and measure the kerf width. STEP 3: Select the riving knife as shown in Fig. 1. STEP 4: Slide the riving knife through the shallow cut (Fig. 3) made in step 2 to confirm the correct riving knife has been selected. The riving knife should not bind or drag through the cut.
IMPORTANT NOTE: If any dragging or binding of the material is encountered as it reaches the riving knife, turn unit off and disconnect machine from power source. Repeat steps 14 to make the proper riving knife selection before attempting another cut.