Академический Документы
Профессиональный Документы
Культура Документы
1) In MODE select DSC and Press Enter 2) Select FUNCTION and press Enter 3) Select EDIT/SEND - Press Enter 4) Select # 1 ( Distress Call ) 5) Select [ EDIT/SEND] and Press Enter. *** Nature of Distress window open *** 6) Select an item from the Window a Nature of Distress and Select OK and Press Enter *** The Input window for Position DATA Open*** 7) Enter the Position Data and select OK and Press Enter *** The Input Window for UTC TIME Data Open *** 8) Enter UTC time data and select OK and Press Enter *** TELECOMMAND window open *** 9) Select an Item from Telecommand Menu Ex .J3E/TEL Press OK and Press Enter . *** SELECTING FOR FREQUENCY Window Open*** 10) Select the Frequency and select Ok and Press Enter 11) The Confirmation Window open. Now you can Start sending 12) Press and hold [ START] until Beeping sounds change from intermitent to Continous. *** The Edited Message are Transmitted .The Initial Display of DSC will return and [ Last Status Message] display the Transmitted Message. Note : If you make Accidental Transmission ,Press [ STOP] with in 5 Secs.
CONFIRMATION OF DELIVERY
1 ) Checking if the Distress Alert has Been Delivered to LES A) After a while a Continous TONE will be Produced for 5 Sec. and following Message will be displayed . DISTRESS ( DATE..TIME .. SUCCEEDED) B) Distress Alert is Transmitted from LES to RCC, if you will see from the Screen ( DISTRESS SUCCEEDED) C) Press [ ESC ] to return to main Menu.
INM-C DISTRESS CALL ( Manual Entry ) If POSITION , COURSE , SPEED , is not correct then procceed to maual entry. 1) Move the cusor to [ DATA SOURCE] and Press [Enter] 2) Move the Cursor to [ Manual ] and press [ Enter ] 3) Enter the Position , Course and Speed manually a) Move to Position Ex. N 123456 [ Enter ] No decimal Points Required E 1234567 [ Enter ] 4) Move cursor to [ COURSE ] and Press [ Enter ] Ex . 1230 [ Enter] No decimal Points Required 5) Move the cursor to [ SPEED ] and Press [ Enter ] Ex. 123 [ Enter ] No decimal points required 6) Move the Cursor to IE and Press [ Enter] --- Press [ F2 ] the LES Window screen will displayed 7) Move the Zcursor to desired LES and Press [ Enter ] 8) The DISTRESS ALERT window will Displayed NOW YOU CAN START TRANSMIT DISTRESS ALERT *** Open Hinged cover and press [ DISTRESS BUTTON] FOR 5 Sec. And buzzer sounds ,Start Sounding when Distress Button is Pressed. *** " SOS" is displayed and alerting sounds to indicate that the Equipment is ready to Transmit a Distress Alert *** At this time the Distress Alert is not Transmitted yet .If the Distress alert transmission is Terminated, Dont Operate Distress Button for 30 Seconds. Buzzer On: 0.5 Seconds OFF 0.5 Seconds *** Press [ Distress Button ] again In the Screen you will see [ SENDING DISTRESS ALERT ] *** COM (TX) will be displayed from left upper corner and Buzzer continous Tone.
CONFIRMATION OF DELIVERY
1 ) Checking if the Distress Alert has Been Delivered to LES A) After a while a Continous TONE will be Produced for 5 Sec. and following Message will be displayed . DISTRESS ( DATE..TIME .. SUCCEEDED) B) Distress Alert is Transmitted from LES to RCC, if you will see from the Screen ( DISTRESS SUCCEEDED) C) Press [ ESC ] to return to main Menu.
2) Select FUNCTION and press Enter 3) Select EDIT/SEND - Press Enter 4) Select # 2 INDIVIDUAL CALL to Coast Station - press\ Enter 5) EDIT/SEND window open -- Press Enter 6) DSC STATION selection Open ( No Station Avail.at Window) a) Press [F5] For Manual Entry 7) Enter COAST STATION ID ex.2371000 ,Olympia Radio and Press [ENTER] **** CATEGORY WINDOW OPEN*** 8) Select DISTRESS and Press [ ENTER] 9) Select [DISTRESS RELAY] Select OK and Press [ ENTER] 10) Enter the DISTRESS ID of Vessel In Distress --Press OK and Press [ENTER] --- Confirm the ID # is you entered is correct---**** NATURE OF DISTRESS WINDOW OPEN*** 11) Select the Nature of DISTRESS menu Select Ok and Press [ ENTER] 12) Input window for POSITION OPEN *** Enter the POSITION and select OK and Press [ENTER] 13) Input window for UTC TIME open *** Enter UTC Time and Select OK and Press[ ENTER] 14) TELECOMMAND 1 Window Open 15) Select an Item from Telecommand Menu Ex.J3E/Tel Select OK and press [ ENTER ] 16) FREQUENCY Mode Open *** Select the FREQUENCY and press [ ENTER] 17) The CONFIRMATION window for Transmitting The Distress Call Open. Now You Can Start Sending Distress relay 18) Press and hold [ START ] until Beeping Sounds Change from Intermittent to Continous . ***** RELAYING A DISTRESS CALLS BEGINS****
INDIVIDUAL CALL TO STATION 1) Set to DSC 2) at main Menu select FUNCTION and Press ENTER 3) select EDIT/SEND and Press ENTER 4) select # 2,INDIVIDUAL TO COAST STATION and Press ENTER 5) Select EDIT/SEND and press ENTER 6) Select Station (Station not Avail in Station List), Press F5 for Manual Entry 7) Enter Coast Station ID Ex.2371000 for olympia radio , omit two Zero and Press ENTER. ** Category Window Open** 8) Select item from CATEGORY MENU and Press ENTER. EX.SAFETY 9) TELECOMMAND 1- windows Open Select J3E TEL if you like to Talk to station or you can select whatever you like and Press ENTER. 10) TELECOMMAND 2 - Windows open You can Select any Ex. You select "NO INFORMATION" Press ENTER. 11) ADDITIONAL WINDOW- Open In the Example " Working Frequency is Selected" Ex. TX.16545 ..RX. 16545 and press ENTER 12) After you Press Enter--- Receivable frequency open (RX) A) Enter Receivable Frequency EX.TX.16804.5..RX.16804.5 Press ENTER. 13) CONFIRM WINDOW Open and Press ENTER. 14) They will ask you " IS THE FREQUENCY FREE NOW Press YES and Press ENTER . 15) START TRANSMISSION Press YES and Enter Transmission has been started ,Wait until the STN. Acknowledge your call .If you Heard Alarm and from DSC they will Transfer Automatically to " TEL" Mode and now you can start communicating to Stn.It will print out at end you can see ACK BQ it mean your call acknoledge by a station or ships. NOTE: This Procedure is They same when you want to communicate to other Vessels,but the only thing you have to select No. 3 3) INDIVIDUAL CALL 1 TO ANOTHER STATION. 4) INDIVIDUAL CALL 11 TO ANOTHER STATION. MF/HF ( JRC NCH 852 ) MT Lucky trader
INDIVIDUAL TEST CALL TO STATION SAFETY TEST CALL 1) In MODE --- Press ENTER 1) In Main menu select MODE Press ENTER 2) Select DSC 2) Select DSC 3) Select Function and Press ENTER 3) Select FUNCTION ,Press ENTER 4) Select EDIT/SEND , Press ENTER 4) Select EDIT/SEND and Press ENTER 5) Select No.2- INDIVIDUAL CALL TO COAST STN . 5) Select No.11 ," SAFETY TEST CALL " 6) Select EDIT/SEND - press ENTER 6) Select EDIT/SEND Press ENTER DSC Stn. Window Will open (No STN Program) 7) DSC STATION SELECTION window open 7) Select F5 for Manual Entry -press ENTER Note: No Station Program PRESS F5 for manual 8) Enter Coast Station ID . Ex.2371000 for entry of Stn I.D. 8) Enter Stn. I.D Ex 2371000,always omit 2(two) Olympia radio (Note Always Omit 2(two Zero) 9) CATEGORY WINDOW open ,Select SAFETY Press ENTER . zero 10) From TELECOMMAND 1 select TEST and Press ENTER 9) TX / RX frequency window open 11) TX/RX Frequency open , Enter TX & RX Frequency 10) Enter TX Frequency Ex.TX.2187.5 EX . TX . 12577.. RX .12577 Press OK / ENTER Enter RX Frequency Ex RX.2187.5 12) CONFIRMATION Window Open 11) Press ENTER "They will ask " IS THE FREQUENCY FREE NOW ? 12) CONFIRMATION WINDOW open Press YES and press ENTER. Then they will ask you 13) START TRANSMIT THE CALL ? Select YES and " IS THE FREQUENCY FREE NOW ? press YES and ENTER Press ENTER. 13) START TRANSMIT THE CALL ? Press YES Now Start Transmitting wait for acknowledgment from station And ENTER. if you heard alarm and yellow light flashing on ,it means the station acknowledge your test call.and you see it Now transmission has been started ,Wait the will print out and you can read from TELECOMMAND 1 station to acknowledge your call ,until you heard TEST and EOS: ACK BQ i t means your Test succesfull an ALARM and Yellow light Flashing on and start printing ;in T ELECOMMAND 1 you will see TEST EOS: ACK BQ ,it means your test Successful Note : INDIVIDUAL CALL 1 TO ANOTHER STATION If Stn Not acknowlwdge , try another Frequency INDIVIDUAL CALL 11 TO ANOTHER STATION You can make also a Test from this menu,This menu or maybe the Stn not Giving their acknowledgment when you want to make a test to Some Ships or to coast Stn with 9 ( Nine) digit code Number,same procedure as it is, JRC NCH 852 MF/HF DSC/NBDP / MT Lucky Trader JRC NCH 852 MF/HF DSC/NBDP MT Lucky Trader
HOW TO SEND A TLX VIA INM-C Continued: 8 . Select the File name in the file List and Press Enter EX. EASTMED - File will Open for you for Confirmation if is the one you selected. Press F10 (2x) going back to previous Menu 9 . Move to cursor to LES Press Enter ( Type the LES were u want to use and press Enter or Press F2 for LES List 10 . Move Cursor to" POSITION "- Press Enter if you like to Change - Press Enter . 11 . The Cursor move to" Delivery Confirmation "( When Cofirmation you like to Change -Press Enter until the cursor move to the right side and Press Enter ( Normally we Use OFF) 12 . The cursor move to " CHARACTER CODE " Press Enter if you like to change ,the cursor move to Right ( Normally we set to ITA2 ) press Enter 13 . The Cursor Move " PRIORITY " When Priority you like to Change Press ENTER ( Normal TLX select ROUTINE) 14 . After Confirmation of each Parameter Press F1 to SEND A CALL ( Normally it takes about 3 to 5 min. to complete communications. 15 . After the Mssg has been transmitted to LES " S & F Message send to LES - is displayed Press F10 t o Previous Menu. Note : Sometime if your call is not Succesfull or not Deliver to Subscriber after a Couple of Minutes Message will displayed saying " Not Deliver to Subscriber " even the Confirmation Is OFF
SETTING NAVAREA
1) Select EGC --Press Enter 2) The NAVAREA Window will Open. 3) Select NAVAREA which you want to Receive after Selecting ,Press ENTER 4) The cursor will Move to ENABLE / DISABLE Move the cursor to ENABLE if you want to Receive and Press ENTER. Or if you dont WANT to receive that NAVAREA Select DISABLE and Press Enter. 5) The Cursor will Move to Another NAVAREA 6) Press F10 -- to Move out from Menu. Note : If you want only ONE NAVAREA to receive Try to use INM-C # 2 to receive Navarea to to Consume Less Paper. Take Note : Sometimes you will be surprised after all setting is correct you dont receive any Weather forecast .Note for the Ocean Region setting it will depend , See ADMIRALTY LIST OF RADIO SIGNALS (VOL 5 ) Page 214 -223
Mt Lucky Trader
4)
Use only this Station as Per Company Instructions 1) Eik Norway 2) Thermopylae ( OTESAT) 3) Xantic ( ex Station 12)
Mt Lucky Trader
AIS
2) Press # 5 ( Initial Setting ) or move the cursor down by Pressing Next--Next until at # 5 (Initial Setting ) and Press Enter ( Initial Setting will Open.) 3) Press 1 ---- or select 1( Set Ships Data ) Press Enter. ( The Cursor will Blink at Ships Name) 4) Press Next ---Next ,until cursor Blink at DRAUGHT (Now you can change draft by Pressing Numbers Sign.Ex.18.5 Press Enter . ( It will Going back to --INITIAL SETTING SETTING DESTINATION 5) Press # 2 --- or move cursor down by Pressing Next---Next ,until your cursor at # 2 ( SET DESTINATION) ,Press Enter. 6) [ SET DESTINATION ] Open. A) The cursor will Blink at Date; Change the DATE of arrival at your Next Port of Call ---after Complete Setting , Press Next B) The cursor will blink at TIME. Change the Arrival TIME at next Port of Call ----- after complete setting of TIME ,Press NEXT C) The Cursor will Move to DESTINATION NOTE: When Cursor at DESTINATION , at LEFT side lower corner you will see 123 number signs , Change this into Alphabet words by Pressing [SFT] ---after Pressing you will see ABC , now you can start writing DESTINATION or your next port of call . After Complete Setting 8) Press ENTER ---[ENT] 9) Press [ MENU] ---to move back to Main MENU 10) They will ask you to SAVE Press YES and Press [ ENT ] Note :Dont Change the Name of the Ship ,If you Made By Mistake Correct it or Move out from menu, but dont Save . Unless otherwise the Vessels Name will Change. FURUNO AIS FA - 100 Mt Lucky Trader H.Gilera