Академический Документы
Профессиональный Документы
Культура Документы
2 Marks: 1. What is measurement? Give its type. 2. Mention the two important requirements of measurements. 3. Define primary sensing elements. 4. What are the categories of S.I units? 5. Define the term standard. 6. Define precisionand accuracy 7. Define systematic error. 8. What are the sources of errors? 9. Define the term repeatability. 10. Define the term calibration. 11.Give classification of measuring instruments. 12.Define True size: 13.Give any four methods of measurement 14.Classify the Absolute error. 15.What is Relative error 16. Classify the errors 17.What is the need of inspection
UNIT III SCREW THREAD AND GEAR FORM MEASUREMENTS 2 Marks: 1. Define the effective diameter of thread. 2. Give the names of the various methods of measuring the minor diameter. 3. What are the types of pitch errors found in screws? 4. What is the effect of flank angle error? 5. What are the applications of toolmaker's microscope? 6. Name the types of gears. 7. Define addendum and dedendum. 8. Define module. 9. Name the gear errors. 10. What are the types of profile checking method? 16 Marks: 1. Discuss briefly about errors in threads with neat sketch. (16) 2. Describe the following methods of measuring the major diameter with a ne at sketch. (i)Ordinary micrometer, (ii) Bench micrometer. (8+8) 3. Draw and explain the measurement of effective diameter of a screw thread using two wires. (16) 4. Explain the following with neat sketch. (i) Tool makers microscope. (ii) Floating carriage micrometer. (8+8) 5. Discuss briefly about the gear terminology with a neat sketch. (16) 6. Explain the following with neat sketch. (i) Pitch measurement. (ii) Profile checking method. (8+8) 7. Explain the principle of measuring gear tooth thickness by gear tooth ve rnier caliper and derive the mathematical formula. (16) 8. Describe briefly the following methods of tooth thickness measurement, (i) Base tangent method. (ii) Constant chord method. (8+8) UNIT IV LASER METROLOGY AND CMM 2 Marks: 1. Why laser is preferred in engineering metrology. 2. Define wavelength. 3. What is Interferometer? 4. Give the different types of interferometer.
5. Name the common source of light used for interferometer. 6. Define CMM. 7. Mention the types of CMM. 8. Define position accuracy. 9. Give the advantages of CMM. 10. Mention the applications of CMM. 16 Marks: 1. Discuss briefly about the Laser telemetric system with a neat sketch. (16) 2. Discuss briefly about the AC laser interferometer with a neat sketch. (16) 3. Discuss briefly about the Dual frequency laser interferometer with a nea t sketch. (16) 4. Explain the following with neat sketch. (i) Michelson interferometer. (ii) Applications of laser interferometer. (8+8) 5. Discuss briefly about the Co-ordinate measuring machine with a neat sket ch. (16) 6. State the advantages, disadvantages and possible sources of errors in CM M. (16) 7. Discuss briefly about the Computer controlled CMM and features of CMM so ftwares. (16) 8. Write short notes on: (i) Computer based inspection (ii) Computer aided inspection using robots. (8+8) UNIT V POWER, FLOW AND TEMPERATURE MEASUREMENTS 2 Marks: 1. Define force. 2. Give the list of devices used to measure the force. 3. Define the working of load cells. 4. Name the instrument used for measurement of torque. 5. Give the basic principle of mechanical torsion meter. 6. Classify the types of strain gauges. 7. Mention the types of dynamometer. 8. Mention the advantages and disadvantages of orifice meter. 9. Define thermocouple. 10. What are the different types of bi- metallic sensors? 16 Marks: 1. Discuss briefly about the measurement of Force by direct method. (16) 2. Discuss briefly about the measurement of Force by indirect method. (16)
3. Discuss briefly about the Torque measurements using torsion bars and pro ney brake. (16) 4. Discuss briefly about the torque measurements using strain gauge. (16) 5. Discuss briefly about the power measurements using D.C dynamometer and h ydraulic dynamometer. (16) 6. Discuss briefly about the flow measurements using orifice meter and vent urimeter. (16) 7. Discuss briefly about the temperature measurements using bimetallic stri p and pressure thermometer. (16) 8. Discuss briefly about the temperature measurement using thermocouple. (16)