Академический Документы
Профессиональный Документы
Культура Документы
Date of submission Border, title block and projection symbol Quality of drawing Accuracy of front elevation Accuracy of end elevation Dimensions Section planes Exercise 2 Total Mark Markers name (please write clearly!)
18/3/2011 Marks out of 8 Marks out of 6 Marks out of 10 Marks out of 10 Marks out of 10 Marks out of 6 Marks out of 50
Additional feedback from the marker will be given on the drawings if necessary
Cut or tear off using ruler Drawing Office Exercise 2 Coursework Receipt Please retain this receipt as proof your coursework was submitted. In the unlikely event that your coursework goes missing no credit will be given if you cannot produce this receipt.
Student Name Student ID number Student DM1 Group number Coursework received by (write clearly) Date
Exercise 2 Marks Scheme Border (2), title block (2) and projection symbol (4) (out of 8) Marks lost for: features missing, projection symbol too large/small/scruffy/wrong Printing poor Drawing quality (out of 6) Good features include: Good line quality (not too wide or too thin, not smudged) Construction lines clearly more faint and narrow than outlines Orthogonal axes used and at approximately the right angles Curves neatly drawn Hatching lines appropriate weight, spacing and angle Poor features include: Line types cannot be distinguished Lines smudged (too soft a pencil) Curves poorly drawn Dotted lines (hidden detail) and centrelines included Hatching poor Accuracy of views (10 each, out of 20 total) 16 20 Completely correct or a few minor mistakes/omissions 11 - 15 A few parts wrong, mostly correct 6 10 Significant mistakes some parts correct 15 Displays little understanding, almost or all incorrect Dimensions (out of 10) Good features: Appropriately placed Leader lines correct Arrow heads appropriate Text correctly placed and oriented Appropriate number of dimensions (no duplicates or omissions) Thought given to how dimensions will be used in manufacture Dimension notes used appropriately Circular features appropriately dimensioned Section planes (out of 6) Marks for correctly indicating and titling both section planes in an approved manner.
Exercise 2: Detail drawing of a piston Component description In an internal combustion engine the pistons are joined to the cranskshaft by connecting rods. In the diagram, N is the connecting rod and M is the piston. The piston is secured to the connecting rod by a gudgeon pin that passes through both connecting rod and piston. The pin is a tight fit in the piston and is held in place with circlips fitted in grooves at the ends of the gudgeon pin holes (these circlip grooves are not included on the simplified piston of exercise 2). The seal between piston and cylinder is provided by 3 piston rings fitted in grooves machined at the top (crown) of the piston. An additional ring is often fitted to the bottom (skirt) of the piston to scrape oil from the cylinder bore (this ring is not included on the How Stuff Works illustration).
Task Use an A3 sheet of plain paper and add a border, projection symbol and title block. Put your name, DM1 group, student ID no., date, drawing title, drawing units and drawing scale in the title block. Sketch (to scale, using a ruler for straight edges and compasses for circles) using 3rd angle projection, two full-size orthographic views of the piston illustrated below. These should be two half-sectional elevations. The drawing should be fully dimensioned such that the component could be manufactured, but there should be no redundant dimensions. The section planes should be indicated appropriately.
combustion chamber
crown
skirt
The dimensions of the piston are given below. Note that you should not require many more dimensions than this to fully specify the component on your drawing.
Feature
Piston diameter Piston height Crown thickness Combustion chamber radius Gudgeon pin hole diameter Distance from gudgeon pin centreline to top of piston crown Wall thickness of casting around gudgeon pin hole Clearance width for small end bearing Skirt wall thickness (except near gudgeon pin hole) Piston ring grooves Distance from top of crown to centreline of upper piston ring groove Distance between piston ring groove centres Scraper ring groove Distance from bottom of skirt to centreline of scraper ring groove All internal fillet radii
mm
80 106 33 25 30 63 5 35.5 8 2.5 wide by 3.5 deep 15 7 5 wide by 3.5 deep 21 3
In the drawing office there will be pistons similar to the one you are drawing for you to look at if necessary. Please ask one of the tutors. Bear in mind that the drawing you submit should be as indicated here, as the pistons available in class are not exactly the same. If you want to add a plan view in order to indicate your section planes feel free to do so.