Академический Документы
Профессиональный Документы
Культура Документы
2. SOLVENT EXTRACTION
Although solvent extraction as a method of separation has long been known to the chemists, only in recent years it has achieved recognition among analysts as a powerful separation technique. Liquid-liquid extraction, mostly used in analysis, is a technique in which a solution is brought into contact with a second solvent, essentially immiscible with the first, in order to bring the transfer of one or more solutes into the second solvent. The separations that can be achieved by this method are simple, convenient and rapid to perform; they are clean as much as the small interfacial area certainly precludes any phenomena analogous to the undesirable co-precipitation encountered in precipitation separations. Solvent extraction is one of the most extensively studied and most widely used techniques for the separation and pre-concentration of elements [67-69]. The technique has become more useful in recent years due to the development of selective chelating agents [70-73] for trace metal determination. With proper choice of extracting agents, this technique can achieve group separation or selective separation of trace elements with high efficiencies. In analytical applications solvent extraction may serve the following three purposes: i) ii) iii) Preconcentration of trace elements Elimination of matrix interference Differentiation of chemical species.
The procedure is applicable to both, trace and macro levels. A further advantage of solvent extraction method lies in the convenience of subsequent analysis of the extracted species. If the extracted species are coloured, as is the case with many chelates, spectrophotometric methods can be employed. Alternatively, the solution may be
12
aspirated for atomic absorption or ICP-emission spectrometric analysis. If radiotracers are used, radioactive counting techniques can be employed. Before going in detailed discussion of fundamental principles of extraction, the three mostly used terms for expressing the effectiveness of extraction processes are being defined below. These terms are basic for understanding of theoretical as well as practical considerations of the subject.
(2.1)
Where [A] represents the stoichiometric or formal concentration of a substance A and the subscripts 1 and 2 refer to the two phases. Since in most cases, two-phase system is of analytical interest, an organic solvent and aqueous are involved, D will be understood to be;
D= [ A]Org [ A] Aq (2.2)
The subscripts org and Aq refer to the organic and aqueous phases respectively.
13
Where V represent solvent volume and the other quantities remain as previously defined. The percent extraction may be seen to vary with the volume ratio of the two phases as well as with D. It may also be seen from equation (2.3) that at extreme values of D, E becomes less sensitive to changes in D. For example, at a phase volume ratio of unity, for any value of D below 0.001, the solute may be considered quantitatively retained in the aqueous phase whereas for D values from 500 to 1000, the value of E changes only from 99.5 to 99.9%.
Separation Factor ()
Since solvent extraction is used for the separation of different elements and species from each other, it becomes necessary to introduce a term to describe the effectiveness of separation of two solutes. The separation factor is related to the individual distribution ratios as follows:
[ A]Org [ B ]Org [ A] Aq [ B ] Aq
[ A]Org [ A] Aq [ B ]Org [ B ] Aq
DA DB
(2.4)
where A and B represent the respective solutes. In those systems where one of the distribution ratios is very small and the other relatively large, complete separations can be quickly and easily achieved. If the separation factor is large but the smaller distribution ratio is sufficiently large then less separation of both components occurs. It is then necessary to apply various techniques to suppress the extraction of the undesired component.
14
immiscible solvents so that at equilibrium the ratio of the concentrations of the solute in the two phases at a particular temperature will be constant, provided the solute is not involved in chemical interactions in either phase [74]. For such a solute, then [ A]Org [ A] Aq
Kd =
=D
(2.5)
where Kd is termed as the distribution coefficient. Deviations from the distribution law arise from two sources: (a) neglect of activity corrections and (b) participations of the distributing solute in chemical interactions in either or both of the two solvent phases. Although the distribution law, as described in equation (2.5) is not thermodynamically rigorous, variation in Kd due to variation in activity coefficients is likely to be under one order of magnitude for most extraction systems of interest to analysts. Far more important are the changes in extraction characteristics of solute because of chemical changes, which occur. Such changes do not represent failure of the law. Rather, they add complexity to the distribution expressions, which can be properly accounted for by using appropriate equilibrium expressions. The distribution of acetic acid between benzene and water may serve as an illustration of the effects of chemical interactions of the solute. The distribution of acetic acid itself may be described as follows:
(CH 3 COOH ) Aq (CH 3 COOH ) Org
KD =
(2.6)
(2.7)
15
D=
[CH 3 COOH ]O [CH 3COOH ]O + [(CH 3 COOH ) 2 ] 2 O = [CH 3 COOH ]W [CH 3 COOH ]W + [CH 3 COO ]
(2.9)
Upon incorporation of the equilibrium expression in Eq. (2.6), (2.7) and (2.8) in Eq. (2.9) there results
D= K D [1 + 2 K P [CH 3COOH ]O ] 1 + K A [H + ]
(2.10)
This shows how the distribution of acetic acid varies as a function of pH and acetic acid concentration.
These three aspects are shared by almost all extraction systems and serve as the basis of a useful organizational pattern.
already uncharged and extractable. Such aqueous phase reactions if do occur might well transform these to charged non-extractable species, e.g. RCOOH + H 2 O RCOO + H 3 O +
RNH 2 + H 2 O R N H 3 + OH
+
In contrast, most of the inorganic compounds are dissociated, so that in order to extract a species of interest into an organic solvent, reactions in the aqueous phase leading to the formation of an uncharged, extractable complex must be utilized. For example, in order to extract aluminum-III from an aqueous solution of aluminum nitrate, one must bring about the reaction of the aluminum-III cation with a reagent such as 8-quinolinol to form aluminum-8-quinolinate, which may be extracted into a variety of organic solvents such as chloroform or benzene [75]. Therefore, the formation of an uncharged complex is very important in the extraction of metals and other inorganic species that makes it convenient to classify such extractions according to the nature of the complexes.
17
solvent approach each other [76]. The solubility parameter, defined as the square root of the heat of vaporization per milliliter, is a measure of cohesive energy density. Comparison of solubility parameters should be of maximum assistance of dealing with those organic extraction systems in which specific chemical or associative forces are inoperative. Burrell has successfully used solubility parameters to rationalize the solubility behavior of various polymers [77]. In systems, where hydrogen bonding may be present, particularly those involving an aqueous phase, the solubility parameter is inadequate in predicting solubility. This might be expected in as much as this concept is, strictly speaking, applicable only in regular solutions. Collander has been able to observe regularities in distribution characteristics in systems involving hydrogen bonding. On the basis of the determination of Kd values for two hundred organic compounds in the ethyl ether-water system, he noted that low Kd values were obtained for compounds having groups capable of hydrogen bonding, such as alcohol, amines, carboxylic acids, and acid amides [78]. Increasing the molecular weight of the organic portion of the molecule would increase the
Kd value about two to four times for each additional methylene group in the homologous
series. The effect to the oxygen in the molecule seemed to be about the same for alcohols, ketones, aldehydes and carboxylic acids. Increase in Kd resulting in replacing alcoholic or carboxylic hydrogen with methyl group seemed to be little more than would be expected upon the increase in molecular weight. Increase in Kd were observed with the introduction of a halogen atom. Pasquinelli has been able to correlate the mutual solubilities of a pair of liquids with the electric and magnetic properties of the pure components [79]. The relation, that has been used to predict solubilities with probable absolute error of about 3% for 100 pairs of liquids, involves the dipole moments, dielectric constant, specific magnetic
18
susceptibility and molar volume. In as much as the prediction may be made for systems involving hydrogen bonding, the relation may be more generally applicable than the comparison of solubility parameters. Solubility of metal salts in aqueous media can be explained on the basis of two special properties of water. First, its high dielectric constant permits dissociation of ionic species relatively easily. Even more important, the high basic character of water results in the solvation of cations (and anions), which gives these ions a solvent sheath serving to reduce electrostatic interaction and to make the ions more solvent-like. The role of the complex forming extraction agent is largely to replace the coordinated water from around the metal ion to give a species that is more likely to be soluble in organic solvents. The solubility characteristics of metal chelates in organic solvents in general terms are not at all unlike those of conventional organic compounds. For example, hydrocarbon substituents will increase the solubility of chelates in organic solvents. Although the neodymium chelate of cupferron-(I) is not soluble in chloroform where as the corresponding neocupferron (II) is soluble in chloroform.
N = O N (I) O (II)
N= O N O
Polar substituents will of course reduce solubility in organic solvents. The chelates of 8-quinolinol-5-sulphonic acid are not at all soluble in organic solvents but are quite soluble in water.
19
Among the ion association complexes, the oxonium type is noteworthy, since in most cases the solvent participates directly in complex formation. The ability of the oxonium solvent to replace water from the coordination sphere of the metal would depend upon the basicity of solvent, which in turn would reflect the electron density and steric availability of the electron pair in the oxygen of the solvent molecule. Many ion association extractions are aided by the use of salting-out agents, electrolytes used in high concentrations to; (a) Produce a mass action effect by adding a common ion, (b) Reduce water activity greatly, (c) Lower the dielectric constant so as to favor ion-pair formation. The use of salting-out agents in organic extractions is also well known.
solvating tendency of water since hydrated ions experience less inter ionic attraction and resemble more closely the medium in which they are dispersed. In fact, for a metal to form an extractable complex, it is necessary to remove some or all of the water molecules associated with the metal ion. Complexing of metal ions leading to the formation of uncharged species falls into two main categories, one involving coordination and the other ion association.
Cu 2+ + 4 : NH 3 Cu ( NH 3 ) 4
2+
From the above examples, only the first one give the neutral, extractable complex.
21
2+ 1/3 Fe 2+
1/2 Cu2++ CH
H C 3 C O C OH CH 3 CH 3 C O
H C C O Cu /2 CH 3
H+
acetylacetone
uncharged
Chelates have relatively large stability constants, so their formation greatly lowers the concentration of hydrated metal ion. Those chelating agents such as acetylacetone, cupferron, dithizone, and 8-quinolinol form uncharged, essentially covalent compounds, which are readily soluble in organic solvents. Chelating agents such as dipyridyl or ethylene diamine tetra acid (EDTA) which form charged chelates are useful as metal masking agents.
22
1. -Diketones and Hydroxycarbonyls a) Acetylacetone b) Thenoyltrifluoracetone c) Morin d) Quinalizarine 2. Nitrosonaphthols 3. Salicylaldoxime 1. Pyridyl-azo-naphthol (PAN)
CC
CO
( -) O ( -) N ( -) N
NC CC CN
CO CO NC CO
23
UO2(BuOH)6.(NO3)2 in which the coordinated solvent molecules contribute both to the size of cation and the resemblance of the complex to the solvent [84]. Most of the solvents which participate directly in the formation of ion association complexes are containing oxygen. The term oxonium complex is used here to describe such a complex, since the solvent molecules from coordinate linkages to the metal atoms through their oxygen atoms.
24
Table-2.2
A.
B.
In view of the important role played by complex formation in inorganic extraction systems, it is appropriate to classify these systems in terms of the type of complex formed [85]. Two broad categories are utilized in Table 2.1 and 2.2. Chelate extraction systems include only those involving neutral chelates, since charged chelates must pair with oppositely charged ions to form extractable species. It will be noted that the chelate systems are ordered with respect to the size of the chelate ring. Differentiation of ion association extraction systems is based on the sign of the charge of the metal-containing ion. In those systems in which the metal is part of the
25
anion, a further classification on the basis of the nature of the cation is helpful. These cations are usually varieties of onium ions such as oxonium, ammonium, arsonium, etc., as mentioned in the Table 2.1. Organic extractions may be classified in a manner similar to that utilized for metal extractions that is on the basis of chemical interactions. However, aside from conventional acid-base reactions which permit control of the extraction via pH, the utilization of chemical reactions in organic extractions are not frequently encountered. In view of the vast number of organic compounds and biological material that extract, a simple method of classification of organic extractions based on the class of compounds to which a particular solute belongs is often used [86, 87] and any general organic text may be consulted for these classes.
26
extraction may be conveniently visualized as follows. The chelating agent distributes between the two phases. Since the majority of chelating extractants exhibit an acid dissociation, the symbol HR will serve as a general formula for the reagent.
HRaq HRorg K DR =
[ HR]Org [ HR] aq (2.11)
HR H + + R
Ka = [ H + ][ R ] [ HR ]
(2.12)
To give a chelating anion R-, which reacts with the metal ion and forms the extractable chelate
M n + + nR MRn
Kf = [ MRn ] [ M n + ][ R ] n
(2.13)
The distribution ratio D can be evaluated from these equilibrium expressions if the metal chelate MRn, may be assumed to be the only metal-containing species in the organic
27
phase and the metal ion, M+, essentially the only metal-containing species in the aqueous phase. Thus
[ M ]Org [ M ] Aq
[ MRn ]Org [ M n + ] Aq
K f K a K DX [ HR]Org n K DR
n
[ H + ]n Aq
(2.15)
The validity of this equation was first verified by Kolthoff and Sandell [89] for dithizone extractions and later by Furman et al. for cupferron extraction [90], extends to many chelate extraction systems.
M ( H 2 O) x 1 (OH ) n 1 + H +
28
is important, the assumption made in the derivation of equation (2.15) that the only metalcontaining species in the aqueous phase is M n + must be modified to include the hydrolysis products. This results in an expression for D in which the average value of the exponent, and hence the importance of the hydrogen ion concentration decreases, while the reagent concentration factor remains unchanged [92]. In early extraction work, the reagent concentrations employed were little more than needed to form the metal chelate [93]. An increase in the pH range of good extraction was achieved by using somewhat higher reagent concentrations [94], with employment of very high reagent concentrations a substantial reduction in the pH of extraction can be achieved, permitting extraction from highly acidic solutions [95]. An advantage in using high reagent concentrations that is not evident from Eq. (2.15) arises when the metal involved commonly forms a hydrated, non-extractable chelate, which with high reagent concentrations is transformed to one in which the coordinated water molecules are replaced by those of the reagent [96].
heavier than the aqueous phase than by the relative extraction efficiency of the solvents. However, a closer examination reveals differences, which, may be put to practical use. As may be seen from Eq. (2.15), the solvent affects two quantities, the distribution coefficients of the reagent and of the chelate. A change in solvent would bring about the following relative change in the value of D:
D * K DX .K DR = * n D K DX .K DR
*n
(2.16)
If it is assumed that the change in Kd value for a reagent and chelate are about the same, then Eq. (2.16) predicts that a change to a solvent in which the reagent is more soluble will result in lower D values for polyvalent metals (n >1). An interesting confirmation of this may be found in the comparison of the use of carbon tetrachloride and chloroform for dithizone extractions. Dithizone and its chelates are more soluble in chloroform than in carbon tetrachloride and extractions with the former solvent require a higher pH region than when the latter is used [97].
D1 K f1 .K DX1 = D 2 K f 2 .K D X
(17)
The ease of separation of two metals is seen to be depending not only on the difference in the stability of their chelates but also on the relative solubility of these chelates in the organic solvent. A sufficiently great difference in solubility may result in an extraction sequence that differs from the stability sequence. For instance, although
30
nickel-II and cobalt-II form more stable acetylacetonates than does zinc II [98], the latter is extractable whereas the former two are not [95]. With regard to chelate stability, the order of stability of a number of metal ions has been shown to be fairly independent of the nature of the chelating reagent employed. Mellor and Maley [99] list the following stability sequence for bivalent metal ions: Pd > Cu > Ni > Pb > Co > Zn > Cd > Fe > Mn > Mg Despite the adherence of the behavior of many reagents to the natural stability sequence for metals a number of interesting exceptions are noteworthy. One such example involves the exceptionally high stability of the tris-phenanthroline-iron-II complex [100,101]. The fact that, this complex is more stable than of the corresponding nickel or cobalt chelats has been attributed to resonance stabilization. Steric hindrance in a chelating agent can result increased selectivity. For example, 2,9-dimethylphenanthroline (neocuproine) (1)
N CH 3 (1)
N CH 3
no longer gives the typical phenanthroline like complex with iron-II since the methyl groups greatly hinder the attachment of three reagent molecules around the iron-II ion. This hindrance is minimum in the tetrahedral geomety of two reagent molecules about a univalent tetracoordinated ion such as copper. Steric hindrance of the 2-methyl groups to chelate formation is the reason for the non-reactivity of 2-methyl-8-quinolinol with the small aluminium ion [102]. This reagent offers a distinct advantage over 8-quinolinol in the determination of many metals in the presence of aluminium [103]. It is also possible
31
that reagents containing the mercapto functionality may exhibit a different metal stability sequence than do those containing oxygen [104]. A more generally applicable approach to increasing selectivity in chelate extractions than that of depending on unusual reagents may be based on the use of competing complexing agents, called masking agents. These masking agents, illustrated by cyanide ion or EDTA, form water-soluble complexes with some metals and thus alter the extraction characteristics of these metals. The use of two competing reagents will tend, in favorable cases, to exaggerate even small differences in the stability order to the point where dramatic changes may be observed. For example, copper-II gives more stable chelates with both 8-quinolinol and EDTA than does uranyl ion and hence in the presence of EDTA only uranyl ion may be extracted with 8-quimolinol [105].
32
The rate of transfer of the extractable species from one phase to the other is relatively rapid when reasonable agitation is employed. Barry et al. have shown that simple repeated inversion of the two phases is sufficient to give equilibrium in a relatively short time even if the species concerned possessed a relatively high molecular weight [110]. Unless the liquids are viscous, it may be expected that transfer rates are sufficiently high to permit equilibration with a shaking time of several minutes.
33
34
of withdrawing the phases for sampling involves the use of three graduates. Most of the heavier phase is withdrawn into the first graduate and then the remainder of the heavier phase and a little of the lighter phase are withdrawn into the second graduate. The remaining portion of the lighter phase is run into the third graduate, and the volumes of the three are noted. The second graduate can now be discarded and aliquots of the other two taken without danger of contamination of one by the other. If droplets of aqueous phase are entrained in the organic extract, it is possible to remove them by filtering the extract through a dry filter paper. The aqueous droplets will be absorbed by the paper, which should be washed several times with fresh organic solvent. Another method commonly used in extractions is the addition of a drying agent, such as sodium sulphate, to the organic extract. Perhaps, the simplest technique for removal of slight traces of the aqueous phase which may contain certain impurities is the use of the backwash technique, described later.
35
ratio and the relative volumes of the two phases and other factors. One practical method of improving the efficiency is to ensure as high an area of contact as possible between the two liquids. As the extracting solvent passes through the solution, fritted-glass discs, small orifices, baffles and stirrers may be used to bring the two immiscible layers in closer contact.
given system is a function of pH. For this reason, curves of extractability versus pH at constant reagent concentration are of great analytical significance. Acidity greatly affects many of the oxonium type of extraction systems, particularly when the metal is extracted as a complex acid. In many of the extractions involving metal halide complexes, e.g., the distribution increases within certain limits with increasing acid concentration. Thus, maximum extraction of iron as the chloride is observed at 6M hydrochloric acid using ethyl ether as the solvent [111]. A decrease in extraction at higher acid concentrations has been attributed to the high solubility of ethyl ether in highly concentrated hydrochloric acid and extraction does not occur until there is a much higher acid concentration with the less soluble isopropyl ether. No decrease is observed even at 12 M hydrochloric acid when : dichloroehtyl ether is used [112]. The addition of high concentrations of acid also enhances the distribution of metal complexes as a result of the common ion effect resulting from the anion of the acid. As the removal of the acidic or basic solute will tend to change the pH value, even more important in multiple extractions (countercurrent distribution), the use of buffer mixture in the aqueous phase aids in the attainment of reproducible constant distribution ratios. Buffers should be chosen which do not interfere in the subsequent analysis [113].
38
molecules for use as a solvent. High concentrations of inorganic salts are usually required to produce the desired effect, the aqueous phase often being saturated with the added salt. It is essential that the added salt` is not extracted to an appreciable extent with the desired species in order to maintain the optimum effect and to permit direct use of the organic extract without further separation. Sometimes the aqueous phase after extraction may be of interest so that the presence of large amounts of added cations prevent further use of this phase in the subsequent analytical steps unless the added salt can be easily removed or destroyed, like ammonium salts. In addition to enhancement of the extraction of the metal of interest using saltingout agents, it is also possible to increase the extraction of impurities in the system. Thus, it is necessary to choose an agent that produces a favorable separation factor between the element of interest and the impurities. The magnitude of enhancement of extraction by the added salt depends on the charge as well as the ionic size of the added cation for a given anion. Thus, polyvalent cations provide better salting-out agents, and for a given charge, the smaller the cationic size, the greater the effect on extraction. However, it must be remembered that anomalies sometimes result from specific interaction effects. Aluminum or calcium salts are strong salting-out agents, whereas ammonium salts are much weaker but analytically more convenient. Among the metal extraction systems that have benefitted through the use of salting-out agents are the nitrate, halide, and thiocyanate systems. Other oxonium extraction systems should be investigated so that useful analytical separations may result where now only limited extractability of a substance occurs.
prevent the formation of their extractable metal complexes. For example, the extraction of iron from chloride solutions can be prevented by reduction to iron-II, which is not extractble. Similarly, antimony-V may be reduced to the tervalent state to suppress its extraction. Conversely, it is important in the preparation of a solution for extraction to adjust the proper valence state of metal ion required for formation of the complex in order to insure complete extraction of that element. Selectivity can also be achieved by variation of the oxidation state of the co-extracted interfering ions during the stripping operation.
2.7.5 pH
The attainment of selectivity in metal chelate extractions is greatly dependent upon proper pH control. As has been mentioned earlier, the distribution of chelates in a given system is a function of pH alone, provided the reagent concentration is maintained constant. Increased selectivity can be achieved in the extraction of acidic or basic organic substances by the addition of buffer salts to the aqueous phase to control the pH [113].
2.7.6 Masking
In the extraction procedures for metal pairs that are difficult to separate, masking or sequestering agents are introduced to improve the separation factor. The masking agent forms water-soluble complexes with the metals in competition with the extracting agent. Masking agents form sufficiently strong complexes with interfering metals to prevent their reactions with the extraction agents, either altogether or at least until the pH is much higher than the value needed for quantitative extraction of the metal of interest. Very often the metal of interest also forms a complex with masking agent, with the result that a somewhat higher pH range is needed for the extraction The application of masking agents, which include cyanide, tartarate, citrate, fluoride, and EDTA, is restricted largely to metal chelate extraction systems, since in the highly acidic solutions encountered in
40
many inorganic extraction systems most masking agents, being weak bases, do not function effectively. Ethylenediaminetetraacetic acid, which is proving a most useful masking agent, has been applied to dithizone, 8-quinolinol, carboxylic acids, acetyl acetone, and diethyldithiocarbamate extractions.
2.7.7 Backwashing
An auxiliary technique used with batch extractions to effect quantitative separations of elements is backwashing. The combined organic phases from several extractions of the original aqueous phase contain practically all the desired elements and possibly some of the impurities that have been extracted to a much smaller extent. This combined organic phase when shaken with one or more small portions of a fresh aqueous phase containing the optimum reagent /salting agent concentration, acidity, etc., will result in a redistribution of the impurities in favour of the aqueous phase since their distribution ratios are low. Under optimum conditions, most of the elements of interest will remain in the organic layer, since their distribution ratio is high. This technique is analogous in many respects to the re-precipitation step in a gravimetric precipitation procedure. With the proper conditions, most of the impurities can be removed by this backwashing operation, with negligible loss of the main component, thereby attaining a selective separation.
41
observed by the B15C5 while little extraction with HPA was observed but quantitative extraction exhibits with the mixture.
100 80 60 40
Extraction (%)
Ce(III)
20 0 1 1.2 1.4 1.6 1.8 2
pH
Fig. 1 Extraction of Ce(III) B15C5(), HPA () and HPA+B15C5() In general, the enhancement of the extraction may be attributed to either thermodynamical changes in the activities of the extractants or the composition of the metal-bearing species in the organic phase, which is not the same as in the cases of individual extractant systems. Synergic systems are usually mixture of cation exchange extractant and coordination extractant and the synergistic effect is thought to operate by an enhancement of the ease with which the coordination sphere of the metal ion can be satisfied. Two methods of accomplishing this have been proposed. In the first, the synergist, S replaces coordinated water in an extracted metal complex, thus making the resulting complex more organophilic. In the second, the original extractable complex is coordinately unsaturated and the synergist S adds to the complex, thereby enhancing its stability. Synergism was first reported in the literature for the extraction of uranium (VI) with various dialkylphosphoric acid and neutral phosphorus alkylesters [115]. Now the synergism appears to be a common phenomenon in many mixed extractant systems. In
42
addition to organophosphorus compounds, hetrocyclic bases, sulfoxides, carboxylic acids, phenols and amines are also common synergists. The synergistic effect is extremely useful in solvent extraction practices and has been used for the extraction of various alkali and alkaline earth metals [116-119], transition metals [120-123] and rare earths [124-129] using different combinations of reagents.
43
As an example we can consider the equilibria of a metal ion, Mn+ with chelating agent (e.g. HA), the extraction of Mn+ by HA alone can be represented by the following reaction.
KA M n + + nHAorg MAnorg + nH +
KA =
[ MAn ]org [ H + ] n
n [ M + n ][ HA]Org
(2.18)
[ MAn ]org [M +n ]
K A = DA [ H + ]n n [ HA]org
= DA
(2.19)
or
DA = K A
n [ HA]org
[ H + ]n
(2.20) (2.21)
pH = log[ H
44
(2.22)
(2.23)
At constant concentration of HA, this equation represents the equation of a line. If log DA is poltted a of intercept of this line. At constant pH, the plot of log DA vs log [HA] will give a straight line, having slope equal to total number of HA molecules participating in the complex formation.
2.8.1.1.2 Synergistic Extraction
As an example we can consider the equilibria of a metal ion, Mn+ with chelating agent (e.g. HA) and a neutral oxo-donor, S (TBP, TOPO, TPPO and DOSO etc.). Considering the synergistic extraction
+ n+ syn n M aq + nHAorg + mS org M ( A) n .mS org + nH aq K
(2.24)
Where m=1 or 2 and K synn is the mixed equilibrium constant. It can be shown that Dsyn1 = K syn1
2 n [ HA]org [ S ]Org
[ H ]n aq
n 2 [ HA]org [ S ]org
(2.25)
Dsyn2 = K syn2
[ H + ]n aq
(2.26)
The equilibrium constants of such reactions refer only to concentration quotients whose calculations are based on the assumption that the activity coefficient of the species involved do not change significantly under the experimental conditions applied. If it is assumed that M(A)n.2S are the only synergistic specie present in the organic phase, the overall distribution coefficient D is given by D = D A + Dsyn1 + Dsyn2 (2.27)
45
(2.28)
It is clear from Eq. (2.28) that if [ HA]org and [ H + ] aq are maintained constant, plot of ( D D A ) [ S ]org vs [-S]org would be straight line with intercept and slope equal to
K
syn
1
n .([ HA } org /[ H
]n aq )
and
respectively.
The
can be easily obtained from the slope and intercept mentioned above. Further details of these calculations can be seen from references [134] and [135]. In earlier publications [136,137,138,139,140] on the synergistic extraction of metal ions (trivalent lanthanides), several authors have reported the formation of only M(A)3.(S)2 type species in the organic phase. The conclusions have been drawn from the observed second power dependence of the neutral donor (S) in the plots of log D vs log [S]org (keeping other parameters constant). With the knowledge of the stepwise formation of all the complex species, the above supposition would be highly misleading. However, in most of the publications of seventies and later, the formation of the stepwise first and second synergistic species have been reported.
overall concentration of both the ligands used in the synergistic extraction is maintained constant (e.g., 0.01 mol dm-3 ) while changing concentration of both the ligands. log D is plotted vs. mol fraction of the ligands. Number of ligands of both the extractants is determined from the mol fraction of the ligands where maximum extraction is achieved.
47