Академический Документы
Профессиональный Документы
Культура Документы
Preparation
PRIUS V
2012 -
MUDGUARDS
NOTE: Part number of this accessory may not be the same as the part number shown. General Applicability
All Models
*Mandatory
Legend
STOP: Damage to the vehicle may occur. Do not proceed until process has been complied with. OPERATOR SAFETY: Use caution to avoid risk of injury. CAUTION: A process that must be carefully observed in order to reduce the risk of damage to the accessory/vehicle and to ensure a quality installation. TOOLS & EQUIPMENT: Used in Figures calls out the specific tools and equipment recommended for this process. REVISION MARK: This mark highlights a change in installation with respect to previous issue. SAFETY TORQUE: This mark indicates that torque is related to safety.
Conflicts
Note: Ground effects
Notes
Special Tools
None Socket/Driver
Notes
10mm
Installation Tools
Screwdriver Screwdriver Socket/Driver Drill Drill Bit Clean Cloth/Rag
Notes
Phillips #2 & 3 Slot 10mm 6mm (1/4), 8mm (5/16)
Special Chemicals
Cleaner
Notes
3M Prep Solvent-70 Alcohol and water
Issue: B
08/30/11
Page 1 of 5 pages
DIO
TOYOTA
Procedure
PRIUS V
2012 -
MUDGUARDS
Care must be taken when installing this accessory to ensure damage does not occur to the vehicle. The installation of this accessory must follow all instructions and use supplied hardware to ensure an approved quality installation.
1.
A B
(b) When cleaning with 3M Prep Solvent-70 follow the manufacturers directions. Do not allow cleaner to air dry.
Fig. 2-1
Remove existing screws locations B and D. Do not discard. (Fig. 2-1). Remove existing push pin location A Discard (Fig. 2-1). Pull liner forward and install supplied spring clip (narrow) centered over location A with turned up edge on inside of panel. (Fig. 2-1)
(b)
10mm Socket/Driver #2 Phillips/ Slot Screwdriver
(c)
(b)
(c)
(d)
(e)
Issue: B
08/30/11
Page 2 of 5 pages
DIO
TOYOTA
Procedure
PRIUS V
2012 4.
MUDGUARDS
Clean Rear Mounting Area
NOTE: REMOVAL AND REINSTALLATION OF REAR TIRE IS REQUIRED TO DRILL ATTACHMENT HOLES.
(1)
Clean and degrease rear bumper panel where mudguard is to be located with a clean, dry lint free cloth and 3M Prep Solvent-70 or alcohol and water mixture. When cleaning with 3MTM Prep Solvent-70 follow the manufacturers directions. Do not allow cleaner to air dry.
(2)
Identify existing dimple hole locations A and B. (Fig. 5-1) Drill 6mm (1/4) Holes in locations A and B, make sure to drill through panel and liner. (Fig 5-1)
(b)
Drill
Fig. 5-1
(c)
Install supplied spring clips (medium) over panel edge holes with turned up edge on inside of panel. (Fig. 5-2) Indentify existing lower mount hole location C and install supplied (large) spring clip center over hole with turned up edge on inside of panel. (Fig. 5-2)
A
Supplied Spring Clips (Medium)
(d)
Fig. 5-2
Issue: B
08/30/11
Page 3 of 5 pages
DIO
TOYOTA
Procedure
PRIUS V
2012 -
MUDGUARDS
A
Supplied 15mm Screw
(a)
Install supplied 20mm screw in location C while holding part up and into bumper panel. (Fig. 6-1)
C
Mudguard Supplied #20mm Screw
(b)
Fig. 6-1
Install supplied 15mm screws in locations A and B while holding part up and tightly against bumper panel. (Fig. 6-1).
(c)
D
While holding part in position, drill 8mm (5/16) hole in location D. (Fig. 6-2)
8mm Bit
(d)
Supplied Push Pin D
Install supplied push pin into location D while holding part into bumper panel. (Fig. 6-3) Repeat procedure for other side.
(e)
Fig. 6-3
Issue: B
08/30/11
Page 4 of 5 pages
DIO
TOYOTA
PRIUS V
MUDGUARDS
Checklist - these points MUST be checked to ensure a quality installation. Check: Accessory Function Checks Gaps between mudguards and body side
Issue: B
08/30/11
Page 5 of 5 pages
DIO