Вы находитесь на странице: 1из 2

FRONT PANEL REAR PANEL

L.E.D D.P.M. DISPLAY


DISPLAY (Digital Panel Mains
Meter). socket Fuse
(2 Amp)
On / Off
switch RS232

TOLERANCE LIMIT Control Control


ICONS ICONS port 1 port 2

Pressure Dial
regulator indicator
ENTER
SCROLL BUTTON
BUTTONS
Mains
AIR OUTLET CALIBRATION air in Filter
(Control jet BUTTON CONTROL JET drain
and housing) AND HOUSING

NOTE:
FILTER SHOULD BE DRAINED ON A REGULAR BASIS.

START UP:

1. Connect tubing to factory air line.


2. Place jubilee clip over end of tube, connect to air inlet on Flexair and tighten jubilee clip.
3. Connect power lead into electrical supply and Flexair mains power in.
4. Switch on power supply to Flexair.
5. Pull regulator adjuster to unlock and turn clockwise until dial indicator reads 20 p.s.i. (push in to lock).
6. IMPORTANT: You should allow the equipment to settle for one hour before use.

PIN CONFIGURATION:
CONTROL PORT: RS232:
No: 1
PIN 1+2 Red
PIN 3+4 Amber
PIN 5+6 Green
PIN 1+4 Not used OUTPUTS:
No: 2 PIN 2 Send/receive
PIN 3 Receive/send 9600 Baud rate
PIN 3+4 Not used PIN 5 Ground Zero parity
PIN 1+2 RS232 request PIN 6-9 Not used 8 data bits, 1 stop bit

MENU DISPLAY:

Limits Tolerance or Range Master RS232


Up (100) Tol size or High (100) Single
Low (400) Range Polarity Low (400) Cont

MENU FEATURES:

¾ Whilst changing numerical values within the menu, press and hold the scroll button to increase the scrolling speed.
¾ At any point whilst in the menu, you may press and hold the enter key for 3 seconds to return to menu headings
screen and repeat to return to operation mode. However, the settings will default to the previous value if new setting
cycle is not completed.
¾ If there is a loss of power during operation or the unit is switched off, all settings will be stored. If you require the unit
to return to the factory default settings, switch on the power whilst holding down the ‘enter’ key.
MENU NAVIGATION: Note, some versions require a Dongle Key to un-lock key pad.
(ALSO SEE TABLE):

¾ To access or exit set-up menu, press and hold the enter key for 3 seconds.

¾ To change the limit settings (High and low limits of component).


1. Scroll to limits and press enter.
2. Use the scroll keys to adjust upper limit (100) and press enter.
3. Use the scroll keys to adjust lower limit (400) and press enter.
4. Limits are now set and the automatic scale magnification will alter the L.E.D. display.
¾ To change the tolerance or range settings (Working/warning tolerance of component).
1. Scroll to tol size / range and press enter.
2. Use the scroll keys to adjust tolerance / range and press enter.
3. Tolerances / Range are now set and will be displayed during run mode.
¾ To change the master settings (Calibrated readings of 100-400 Flowmasters).
1. Scroll to master and press enter.
2. Use the scroll keys to adjust high Flowmaster reading (97-103) and press enter.
3. Use the scroll keys to adjust lower Flowmaster reading (397-403) and press enter.
4. Master readings are now set and will display during calibration mode.
¾ To change the RS232 output.
1. Scroll to RS232 and press enter.
2. Use the scroll keys to switch between continuous or single string outputs and press enter.
3. RS232 output is now set. Pressing the RED Button while measuring will send out the size via RS232.

ENTER (Hold for 3 sec ond s)

Rs232 LIMITS TOL MST

ENTER ENTER ENTER ENTER

SING LE CONT. 100 200 20 50 100 102

ENTER ENTER ENTER ENTER

Rs232 400 300 400 398

ENTER ENTER

LIMITS MST

ENTER (Hold for 3 sec ond s)

RUNNING

CALIBRATION:

¾ Press and hold Cal key for 5 seconds.


¾ Place high Flowmaster (100) onto air outlet then press Cal.
¾ Place low Flowmaster (400) onto air outlet then press Cal.
¾ Your Flexair flowmeter is now calibrated and ready for use.
Note: The Control jet and Flowmasters should be calibrated annually.

FlexMetrology Systems. Tel: +44 (0)870 143 3008


Unit 2, Home Farm, Fax: +44 (0)870 143 3016
Luton Hoo Estate,
Email: sales@flexmetrology.com
Luton, Bedfordshire. Web: www.flexmetrology.com
LU1 3TD.
United Kingdom Version: 1 Issue: 3

Вам также может понравиться