Академический Документы
Профессиональный Документы
Культура Документы
Name of the project: Member: Grade of Concrete:M35 1 REQUIREMENTS/PARAMETERS 1.A) SPECIFIED MINIMUM STRENGTH(F ck ) 1.B) DURABILITY REQUIREMENTS
2 350 kg/cm
Data unit
Remarks
2 53 N/mm 53 G 100 mm
E-curve preferred. High. Range-(80-120)mm River Sand Average of two sample-92% (fine to very fine sample taken)
a) Type (Natural/Mixed) b) % passing 600 micron sieve ( pure sand) c) Zone d) %retained on 4.75mm IS Sieve e) Specific Gravity f) Dry Loose Bulk Density g) Bulkage h) Surface Moisture
1.F) DETAILS OF COARSE AGGREGATE
Natural 85 % 98.5 % IV nil 2.58 1.47 kg/lit. 15 % 2% rounded 95 % 20 mm 1% 2.58 1.67 kg/lit. Good 5.8 1.28 2 424 kg/cm 0.41 0.45 0.45
a) Type b) % Passing 20mm Sieve c) Maximum size of aggregate(MSA) d) %Passing On 4.75mm Sieve e) Specific Gravity d) Dry Loose Bulk Density(DLBD)
2 TARGET MEAN STRENGTH
a) Degree Of Quality Control b) Standard Deviation S c) Statistical constant selected 't' d) Target Mean Strength 'fm'
3 WATER TO CEMENT RATIO
fm=(fck + S x t). lower value is preferred, however higher one is selected as practically it becomes hard to achieve high slmp with w/c< 0.45 with no admix.
a) Maximum Size of Aggregate(MSA) b) Slump c) Free W/C Ratio d) %Passing on 600 Mic. Sieve e) Proportion of Fine Aggregate
5 PROPORTION OF COARSE AGGREGATE a) PROPORTION OF COARSE AGGREGATE 6 CORRECTIONS IN AGG. PROPORTION 6.A) Corrections due to coarse aggregates in fine
0.72
(1-0.28)
aggregate : a) % Passing 4.75mm Sieve b) % Proportion of Fine Aggregate after correction c) % Proportion of Coarse aggregate after correction.
6.B) Corrections due to fine aggregates in coarse
nil 28
72
aggregates: a) % passing 4.75mm sieve b) % proportion of fine aggregate after correction c) % proportion of coarse aggregates after corrections
7 AGGREGATE TO CEMENT RATIO (A/C):
1 27.28 72.72
a) Maximum size of aggregate(MSA) b) Shape of Agg. -- Fine Agg. (FA) c) -- Coarse Agg. (CA) d) W/C ratio selected e) Workability/Slump f) Grading curve no/Zone g) A/C RATIO 1) for fine aggregate 2) for coarse aggregate h) AGGREGATE PROPORTION 1) for fine aggregate 2) for coarse aggregate
j) A/C PROPORTIONATELY WORK OUT
20 mm Irregular Rounded & irregualr mixed 0.45 100 mm Avg. IV 3.5 3.8 0.27 0.73 0.945 2.774
0.927 2.863 3.790 3.487 3.487 50 kg 22.5 lit 47.25 kg 127.75 kg 50 Kg 22.5 lit 22.8 lit 48.195 kg 127.75 kg Actual adjusted 22.8 50 49 127 248.80 01 bag adjusted for 1% absorption & 2% moisture adjusted for 2% moisture
say 3.50
contdto Pg-3
22.8 50 48.195 127.75 Total Aggregate 248.745 Concrete density Cement Content
Mix No.
Date of casting
Date of testing
Cement (Kg)
Sand (Kg)
Chips (Kg)
Remarks:
WORKSHEET FOR CONCRETE MIXES DESIGN DOE (UK), IS, RRL (UK) -Method Combined Date:
Name of the project: Member: Grade of Concrete:M20 1 REQUIREMENTS/PARAMETERS 1.A) SPECIFIED MINIMUM STRENGTH(F ck ) 1.B) DURABILITY REQUIREMENTS
2 200 kg/cm
Data unit
Remarks
Moderate
2 53 N/mm 53 G 60 mm
E-curve preferred. Medium.Range-(50-70)mm River Sand Average of two sample-92% (fine to very fine sample taken)
a) Type (Natural/Mixed) b) % passing 600 micron sieve ( pure sand) c) Zone d) %retained on 4.75mm IS Sieve e) Specific Gravity f) Dry Loose Bulk Density g) Bulkage h) Surface Moisture
1.F) DETAILS OF COARSE AGGREGATE
Natural 85 % 98.5 % IV nil 2.58 1.47 kg/lit. 15 % 2% rounded 95 % 20 mm 1% 2.58 1.67 kg/lit. Good 4.6 1.65 2 275.9 kg/cm 0.51 0.5 0.5
a) Type b) % Passing 20mm Sieve c) Maximum size of aggregate(MSA) d) %Passing On 4.75mm Sieve e) Specific Gravity d) Dry Loose Bulk Density(DLBD)
2 TARGET MEAN STRENGTH
a) Degree Of Quality Control b) Standard Deviation S c) Statistical constant selected 't' d) Target Mean Strength 'fm'
3 WATER TO CEMENT RATIO
fm=(fck + S x t).
a) Maximum Size of Aggregate(MSA) b) Slump c) Free W/C Ratio d) %Passing on 600 Mic. Sieve e) Proportion of Fine Aggregate
5 PROPORTION OF COARSE AGGREGATE a) PROPORTION OF COARSE AGGREGATE 6 CORRECTIONS IN AGG. PROPORTION 6.A) Corrections due to coarse aggregates in fine
20 mm 60 mm 0.5 92 % 0.26
Avg.
0.74
(1-0.28)
aggregate : a) % Passing 4.75mm Sieve b) % Proportion of Fine Aggregate after correction c) % Proportion of Coarse aggregate after correction.
6.B) Corrections due to fine aggregates in coarse
nil 26
74
aggregates: a) % passing 4.75mm sieve b) % proportion of fine aggregate after correction c) % proportion of coarse aggregates after corrections
7 AGGREGATE TO CEMENT RATIO (A/C):
1 25.28 74.72
a) Maximum size of aggregate(MSA) b) Shape of Agg. -- Fine Agg. (FA) c) -- Coarse Agg. (CA) d) W/C ratio selected e) Workability/Slump f) Grading curve no/Zone g) A/C RATIO 1) for fine aggregate 2) for coarse aggregate h) AGGREGATE PROPORTION 1) for fine aggregate 2) for coarse aggregate
j) A/C PROPORTIONATELY WORK OUT
20 mm Irregular Rounded & irregualr mixed 0.5 60 mm Avg. IV 4.5 5 25.28 % 74.72 % 1.138 3.736
1.116 3.855 4.971 4.573 4.573 50 kg 25 lit 57.8 kg 170.85 kg 50 Kg 25 lit 25.5 lit 58.956 kg 170.85 kg Actual adjusted 25.5 50 60 170 305.50 01 bag adjusted for 1% absorption & 2% moisture adjusted for 2% moisture
contdto Pg-3
25.5 50 58.956 170.85 Total Aggregate 305.306 Concrete density Cement Content
Mix No.
Date of casting
Date of testing
Cement (Kg)
Sand (Kg)
Chips (Kg)
Remarks:
DATE:
1) PROJECT
: : : : : :
2) TYPE 3) PHYSICAL INSPECTION 4) DRY LOOSE BULK DENSITY 5) SOURCE 6) SAMPLE WEIGHT
RETAINED
REMARKS
7) SPECIFIC GRAVITY 8) SILT CONTENT 9) BULKAGE 10) SURFACE MOISTURE 11) DATE OF TESTING 12) TESTED BY 13) REMARKS
: : : : : : :
Name of the project: Member: Grade of Concrete:M30 1 REQUIREMENTS/PARAMETERS 1.A) SPECIFIED MINIMUM STRENGTH(F ck ) 1.B) DURABILITY REQUIREMENTS
Remarks
0.5 300 kg 53 G
2 56.5 N/mm
53 N/mm 53 G 65 mm Natural 85 % 98.5 % IV nil 2.55 1.47 kg/lit. 15 % 2% rounded 95 % 20 mm 1% 2.58 1.67 kg/lit. Good
E-curve preferred. Medium.Range-(60-70)mm River Sand Average of two sample-92% (fine to very fine sample taken)
a) Type (Natural/Mixed) b) % passing 600 micron sieve ( pure sand) c) Zone d) %retained on 4.75mm IS Sieve e) Specific Gravity f) Dry Loose Bulk Density g) Bulkage h) Surface Moisture
1.F) DETAILS OF COARSE AGGREGATE
a) Type b) % Passing 20mm Sieve c) Maximum size of aggregate(MSA) d) %Passing On 4.75mm Sieve e) Specific Gravity d) Dry Loose Bulk Density(DLBD)
2 TARGET MEAN STRENGTH
River Chips
a) Degree Of Quality Control b) Standard Deviation S c) Statistical constant selected 't' d) Target Mean Strength 'fm'
3 WATER TO CEMENT RATIO
fm=(fck + S x t).
Avg.
c) Free W/C Ratio d) %Passing on 600 Mic. Sieve e) Proportion of Fine Aggregate
5 PROPORTION OF COARSE AGGREGATE a) PROPORTION OF COARSE AGGREGATE 6 CORRECTIONS IN AGG. PROPORTION 6.A) Corrections due to coarse aggregates in fine
aggregate : a) % Passing 4.75mm Sieve b) % Proportion of Fine Aggregate after correction c) % Proportion of Coarse aggregate after correction.
6.B) Corrections due to fine aggregates in coarse
nil 28
72
aggregates: a) % passing 4.75mm sieve b) % proportion of fine aggregate after correction c) % proportion of coarse aggregates after corrections
7 AGGREGATE TO CEMENT RATIO (A/C):
1 27
73
a) Maximum size of aggregate(MSA) b) Shape of Agg. -- Fine Agg. (FA) c) -- Coarse Agg. (CA) d) W/C ratio selected e) Workability/Slump f) Grading curve no/Zone g) A/C RATIO 1) for fine aggregate 2) for coarse aggregate h) AGGREGATE PROPORTION 1) for fine aggregate 2) for coarse aggregate
j) A/C PROPORTIONATELY WORK OUT
20 mm Irregular Rounded & irregualr mixed 0.43 65 mm Avg. IV 3.62 3.91 27 % 73 % 0.977 2.854 0.958 2.945 3.903
l) A/C CORRECTED FOR FLAKINESS m)A/C FINAL 8 WEIGH BATCHING: a) CEMENT(50 KG) b) WATER(50KG X W/C) c) FA= 50KG X A/C (FINAL) X % Prop. d) CA= 50KG X A/C (FINAL) X % Prop. 9 BATCHING after adjustments: a) CEMENT(50 KG) b) WATER(50KG X W/C) c) WATER AFTER CORRECTION d) FINE AGGREGATE after adjustment e) COARSE AGGREGATE-CA
3.588 3.6 50 21.5 48.6 131.4 kg lit kg kg 01 bag adjusted for 1% absorption & 2% moisture adjusted for 2% moisture
50 Kg 21.5 lit 21.8 lit 49.572 kg 131.4 kg Actual adjusted 21.8 21.8 50 49.572 50 50 131 252.80
Mix No.
Date of casting
Date of testing
Cement (Kg)
Sand (Kg)
Chips (Kg)
Remarks: