Академический Документы
Профессиональный Документы
Культура Документы
Options for IP Routing and how to configure IP Routing in Windows Server 2008. There are a number of IP Routing changes that you need to be aware of in Windows 2008 Server.
Published: Dec 11, 2008 Updated: Jul 23, 2009 Section: Articles & Tutorials :: Network Protocols Author: David Davis Printable Version Adjust font size: Rating: 3.5/5 - 92 Votes 1 2 3 4 5
31
Introduction
With Windows Server 2008, there are a number of changes to networking and Routing and Remote Access. In fact, I wrote about some of these changes in my WindowsNetworking.com article: Which Windows Server 2008 Networking Services were removed and which should you use instead? In that article, I covered how OSPF is no longer part of Windows Server 2008. I find that unfortunate because I think that OSPF is likely the best dynamic routing protocol ever created. Still, I can also partially understand Microsofts decision to remove it as I would venture to guess that 99.9% of Windows Server Admins never used it. So what are we left with?
With the removal of OSPF, we are left with either 1) static routing or 2) dynamic routing with RIPV2. Lets find out how each of these work.
Ability to automatically add networks by learning them from other RIP routers Ability to automatically remove routes from the routing table when other RIP neighbors delete them Ability to select the best route based on routing metrics Reduce configuration of Windows Server routing systems that have more than a few static routes that need to be added
So how do you configure static and dynamic routing in Windows Server 2008?
Figure 1: Showing the IP Routing table in Windows Server 2008 In the route print output, the first important thing that you see is the interface list. Windows Server IP interfaces are labeled with an interface number. The interface numbers in Figure 1 are 16, 14, 1, 15, 20, and 12. These interface numbers are used whenever you add or delete routes to the routing table.
The second important thing in the route print output is the IPv4 Routing Table. This shows us the network destination, network mask, the default gateway, interface, and metric. This table tells the Windows Server where to route the traffic. Below that is the IPv6 routing table. For more information on IPv6, I recommend Brien Poseys articles Crash Course in IPv6 (Part One) & Crash Course in IPv6 (Part Two) and Mitch Tullochs article IPv6 Support in Microsoft Windows. Add a static route So how do you add a static route at the command line? The answer is easy- use the route add command, like this: route add 1.1.1.0 mask 255.255.255.0 10.0.1.1 if 1 As you see in Figure 2, the results of our route add was an affirmative OK!
Formatted: Font: (Default) Times New Roman, 12 pt, Bold
Figure 2: Using the route add command in Windows 2008 What was important in the route add command was the network we want to add, its subnet, the destination/gateway, and the interface for that route. Delete a static route Deleting a route is even easier than adding a route. All you have to do is to tell route delete the network that you want to remove, as you see in Figure 3.
Formatted: Font: (Default) Times New Roman, 12 pt
Figure 3: Using the route delete command in Windows 2008 So those are the basics of configuring static routes at the command line. Now lets learn about configuring dynamic routing.
1. The first step is to install the Routing and Remote Access (RRAS) role in Windows 2008 Server. If you go into the Add Roles Wizard, the RRAS role can be difficult to find because what you really need to add is the Network Policy and Access Services role then the Routing and Remote Access Services Role (as you see in Figure 4 and Figure 5).
Formatted: Font: (Default) Times New Roman, 12 pt
Figure 4: Adding the RRAS Role through he Network Policy and Access Services
Figure 5: The Win 2008 Role Services are part of the Network Policy and Access Services Role Once installed you can configure RRAS from the Server Manager application but I prefer the Routing and Remove Access application. 2. The second part of this is to Configure Routing and Remote Access by opening the RRAS MMC, right-clicking on the server name, and clicking Configure and Enable Routing and Remote Access, like this:
Formatted: Font: (Default) Times New Roman, 12 pt, Bold
Make sure that you do a Custom Configuration concerning what RRAS protocol to install. Then, choose to install LAN ROUTING then choose to start the service. From there, you can see the Network Interfaces controlled by RRAS and specific configurations for IPV4 and IPV6. At this point, you can expand IPV4, go to General, then to New Routing Protocol.
Formatted: Font: (Default) Times New Roman, 12 pt
Figure 7: Adding a new Routing Protocol Next, choose to install RIPV2 as your routing protocol.
Figure 8: Adding RIP V2 3. Now that you have RIPv2 installed, you can configure it. Configuring it is really as easy as adding the interfaces that you want to use to exchange RIP routes with. To do this, go to the RIP section, right click, click on New Interface, select the interface you want to add under RIP as you see in Figure 9.
Figure 9: Adding a new RIP interface 4. After selecting the interface, you have the option to configure a wide variety of RIP connection properties (as you see in Figure 10). There is more to configuring RIP than I can go into in this article as RIP configuration can either be very simple or it can become very complex.
Figure 10: Configuring the new RIP interface 5. Once you have your RIP interfaces added, you can check to see if you are sending and receiving responses on your RIP interfaces (you should be). You can also check to see if you have any RIP neighbors by right-clicking on the RIP protocol, then clicking Show Neighbors. Before I conclude this section about RIP in Windows, I want to point you to a couple of excellent resources I used while preparing for this article: 1. Recently I was watching Ed Libermans Train Signal Windows 2008 Network Infrastructure video. In that video, besides explaining routing and the differences between static and dynamic routing, Ed shows, step by step, how to configure RIPv2 in Windows 2008. I found the video very helpful and recommend it to you whether you just want to learn about Win 2008 and routing or if you are looking to pass Microsofts Windows 2008 Network Infrastructure exam (70-642). Here is a screenshot of Ed configuring RIPV2:
Figure 11 Train Signals Windows 2008 Video on how to install and configure RIPV2