Академический Документы
Профессиональный Документы
Культура Документы
DN 400 (16)...1200 (80) mm, PN 0,25 (2,5); 1,0 (10); 1,6 (16); 2,5 (25) P (bar)
Application
Used as stop valves for pipelines transporting: - water, vapor and other nonflammable, non-explosive and non-toxic media (Water) at the temperature below +100C (at the temperature up to +250C if requested by the Customer). The butterfly valves can be manufactured for oil pipelines as per Customer requirements.
DesiGn Features
3
2 1. 2.
Highly wear-resistant overlay in the seats extends the valves service life. Sealing ring installed in the disc facilitates replacement of the ring without full disassembly of the valve.
12
www.ptpa.ru
Butterfly Valves
3. Flange connections of the regulators simplify installation and takedown of the valves. 4. Spline joint between the disc and the shaft provides longer operating life compared to the conventional key joint. 5. The valve design incorporates grease injectors that supply lubricants to the bearing assembly of the shaft or the disc and extend operating life of the product. Maintenance frequency once a year, lubricant -323 (GOST 14068-79) or -221 (GOST 943380) or any other grease approved by vendor.
6. The yoke is featured with roller bearings decreasing the effort of the actuator and facilitating valve operation. 7. The regulators have smaller dimensions and weight (compared to other industrial valves designed for similar working media) that enable to use these valves in narrow spaces and with minimum number if supports for the pipeline.
Actuation tiGHtness
Manual or electric drive. When desired by Customer the gate valves may be completed with electric drives of Russian or international manufacturers (AUMA, ROTORK, LIMITORQUE, FESTO, etc).
www.ptpa.ru
13
Butterfly Valves
Rated pressure PN 1,0 (10) P (BAR) Internal diameters DN 400 (16), 500 (20), 600 (24), 800 (32), 1000(40) dimensions and draWinG
Fig. 1 Fig. 2
n mat. d
Fig. 3
* Note: the table contains weights of butterfly valves complete without electric drives.
Materials
When required by Customer butterfly valves may be produced of corrosion-resistant steel. Cadmium or zinc coating is available for tropical versions.
14
www.ptpa.ru
Butterfly Valves
Rated pressure PN 1,6 (16) p (BAR) Internal diameters DN 400 (16), 500 (20), 600 (24), 800 (32) dimensions and draWinG
Fig. 1 Fig. 2
* Note: the table contains weights of butterfly valves complete without electric drives.
Materials
When required by Customer butterfly valves may be produced of corrosion-resistant steel. Cadmium or zinc coating is available for tropical versions.
www.ptpa.ru
15
Butterfly Valves
Rated pressure PN 1,6 (16) P (bar) Internal diameters DN 1000 (40 ), 1200 (48 ) dimensions and draWinG
Fig. 1 B
Fig. 2
* Note: the table contains weights of butterfly valves complete without electric drives.
Materials
When required by Customer butterfly valves may be produced of corrosion-resistant steel. Cadmium or zinc coating is available for tropical versions.
16
www.ptpa.ru
Butterfly Valves
Rated pressure PN 2,5 (16) p (BAR) Internal diameters DN 400 (16), 500 (20), 800 (32) dimensions and draWinG
Fig. 1 Fig. 2
* Note: the table contains weights of butterfly valves complete without electric drives.
Materials
When required by Customer butterfly valves may be produced of corrosion-resistant steel. Cadmium or zinc coating is available for tropical versions.
www.ptpa.ru
17
Butterfly Valves
Rated pressure PN 0,25 (2,5) p (BAR) Internal diameters DN 1400 (56), 1600 (64), 2000 (80) dimensions and draWinG
Fig. 1 Fig. 2
* Note: the table contains weights of butterfly valves complete without electric drives.
Materials
When required by Customer butterfly valves may be produced of corrosion-resistant steel. Cadmium or zinc coating is available for tropical versions.
18
www.ptpa.ru
Application
Used as stop valves for pipelines transporting hot steam, light oil products, liquid and gaseous fluids, aggressive and non-aggressive media, containing high concentration of H2S and CO2, at the temperature reaching +425 C.
DesiGn Features
3
1. Tri -centric design of the disc results in lower torque compared to standard design. 2. Metal-to-metal seats extend service life of the valve. 3. Demountable design of seat/disc and easy seal replacement provide high level of maintainability. Simple and convenient valve design ensures extended service life of the element. The regulators have smaller dimensions and weight (compared to gate valves for similar working media) that enable to use these valves in narrow spaces and with minimum number if supports for the pipeline.
2 1
tHe triple-oFFset GeometrY OFFset 1: The shaft is offset behind the seat axis to allow complete sealing contact around the entire seat. OFFset 2: The shaft centerline is offset from the pipe and valve which provides interference free opening and closing of the valve.
OFFset 3: The seat cone axis is offset from the shaft centerline to eliminate friction during closing and opening and to achieve uniform compressive sealing around the entire seat.
www.ptpa.ru
19
Butterfly Valves
Actuation tiGHtness
Manual or electric drive. When desired by Customer the gate valves may be completed with electric drives of Russian or international manufacturers (AUMA, ROTORK, LIMITORQUE, FESTO, etc).
Materials
When required by Customer butterfly valves may be produced of corrosion-resistant steel. Cadmium or zinc coating is available for tropical versions.
20
www.ptpa.ru