Академический Документы
Профессиональный Документы
Культура Документы
82 85 D8 D1 D4 D7 NY
Studs: Steel, zinc plated plus chromate or chrome plated Bail cover: ABS, black
ACTUAL SIZE
Bail
ACTUAL SIZE
12.5 (.492)
ACTUAL SIZE
3.4 (.134)
Installation Notes
Bail cover: A Retainer must be tted under the stud head to t ush with surface Retainer part number D8-324-100-040 (see page 291)
17.0 (.67)
4.34 (.17)
20 (.79)
www.southco.com/D8
287
82 85
D8 - 314 - H K - F
F Finish 170 Chrome plated 190 Zinc plated 191 Zinc plated, black
D8 D1 D4 D7 NY
To select correct fastener: 1. Select receptacle
L K .15 (.006)
8 (.315) 9 (.354) 10 (.394) 11 (.433) 12 (.472) 13 (.512) 14 (.551) 15 (.591) 16 (.630) 17 (.669) 18 (.709) 19 (.748) 20 (.787) 21 (.827) 22 (.866) 23 (.906) 24 (.945) 25 (.984) 26 (1.02) 27 (1.06) 28 (1.10) 29 (1.14) 30 (1.18)
www.southco.com/D8
288
Rivet-On
8.3 (.327) 12 (.472) 20 (.787) 3.4 (.134) Two places Gasket P P
82 85 D8 D1 D4 D7 NY
Installation Notes
Install with 3 (.125) rivets
18 (.709)
Part Number
See table
Notes
Utilize stud selection column indicated when choosing a stud length from the stud length table on page 287
ACTUAL SIZE
3.6 (.142)
Part Number
D8-334-400-121
Weld-On
8.3 (.327) 12 (.472) 20 (.787) 6.4 (.252) Two places 18 (.709)
Gasket
Part Number
See table
28 (1.10) P 8.00 (.315) F TMT TMT = P + F Compressed gasket TMT = P + F F TMT F TMT
Notes
Utilize stud selection column indicated when choosing a stud length from the stud length table on page 287
ACTUAL SIZE
Part Number
D8-334-500-121
Side Mount
5.4 (.21)
13.7 (.539)
30 (1.18)
12.7 (.500)
1.2 (.047)
Part Number
See table
18 (.709)
Notes
Utilize stud selection column indicated when choosing a stud length from the stud length table on page 287
ACTUAL SIZE
Part Number
D8-334-310-121
www.southco.com/D8
289
Clip-On
8 (.315) 22.5 (.886) 22 (.472) 10 (.394) Gasket P P
82 85 D8
ACTUAL SIZE
P 12.00 (.472) Min. 10.00 (.394) Max. Frame thickness 0.70 (.027) to 2.50 (.098)
F TMT TMT = P + F
D1 D4 D7
Part Number
See table
NY
Notes
Part Number
D8-334-300-121
Utilize stud selection column indicated when choosing a stud length from the stud length table on page 287
Front Mount
9.3 (.366) 12.8 (.50) Gasket 0.5 (.020) 11.5 (.453) P P
ACTUAL SIZE
F TMT
9.50+0.1 (.375.004)
Installation
Part Number
See table
Press & turn Installed position
Notes
Utilize stud selection column indicated when choosing a stud length from the stud length table on page 287
Part Number
D8-334-200-190
www.southco.com/D8
290
Gasket
82 85 D8 D1 D4 D7 NY
Installation Notes
Press receptacle ush to frame
Notes
Receptacle shown installed ush to the frame. To eliminate the gap between the frame and outer panel, install to a depth the thickness of the selected retainer. This depth should be added to the TMT.
ACTUAL SIZE
F TMT
Solid Install
Outer panel
Blind Install
Outer panel
+0.1
Retainer
Part Number
See table
Notes
Utilize stud selection column indicated when choosing a stud length from the stud length table on page 287
Part Number
D8-334-100-300
Press-In - Self-Clinching
13.5 (.531) 10.6 (.417) Gasket P P
Notes
For use in low carbon steels, aluminum and stainless steels in the annealed condition that are RB85 or softer See page 497 for installation guidelines
6.9 (.272)
ACTUAL SIZE
P Edge of hole must be sharp on this side. Do not chamfer. 1.30 (.051) Min. frame thickness TMT TMT = P + Compressed gasket TMT = P + F F TMT F TMT
Part Number
See table
Notes
Utilize stud selection column indicated when choosing a stud length from the stud length table on page 287
Part Number
D8-334-110-190
www.southco.com/D8
291
Retainer Push-On
0.5 (.020) 4.3 (.169)
82 85
10 (.394)
8 (.315)
D8 D1
Adjustment Value
Type
Push-on plastic Push-on
Part Number
D8-324-100-040 D8-324-101-200
Material
High density polyethylene, black Stainless steel
Part Number
See table
D4 D7 NY
Steel retainer
Part Number
X D8-324-200-200 D8-324-201-200
H
48 (1.89) 20 (.787)
X Min.
14 (.551) 5 (.197)
X Max.
44 (1.73) 16 (.630)
www.southco.com/D8
292
82 85 D8 D1 D4 D7 NY
Studs: Steel, zinc plated and chromate or chrome plated or stainless steel Key: Steel with zinc plate and chromate Bail cover: ABS, black
Hex Recess
12 (.472) 4mm Hex 3 (.118)
Phillips Recess
12 (.472) No. 2 Phillips 3 (.118) L
Tamper Resistant
12 (.472)
Accessories
Tamper resistant stud key: Part number: D8-316-007-969
3 (.118) L
ACTUAL SIZE
ACTUAL SIZE
21 2 (.827) (.079)
19 (.748)
24.0 (.94)
29.0 (1.14)
www.southco.com/D8
293
82 85 D8 D1 D4
D8 - 316 - H K - F
D7 NY
10.5 (.41) 11.4 (.45) 10.5 (.41) 11.4 (.45) 11.5 (.45) 12.4 (.49) 11.5 (.45) 12.4 (.49) 12.5 (.49) 13.4 (.53) 12.5 (.49) 13.4 (.53) 13.5 (.53) 14.4 (.57) 13.5 (.53) 14.4 (.57) 14.5 (.57) 15.4 (.61) 14.5 (.57) 15.4 (.61) 15.5 (.61) 16.4 (.65) 15.5 (.61) 16.4 (.65) 16.5 (.65) 17.4 (.69) 16.5 (.65) 17.4 (.69) 17.5 (.69) 18.4 (.72) 17.5 (.69) 18.4 (.72)
10.7 (.42) 11.6 (.46) 11.7 (.46) 12.6 (.50) 11.7 (.46) 12.6 (.50) 12.7 (.50) 13.6 (.54) 12.7 (.50) 13.6 (.54) 13.7 (.54) 14.6 (.57)
10.7 (.42) 13.7 (.54) 14.6 (.57) 14.7 (.58) 15.6 (.61)
18.5 (.73) 19.4 (.76) 18.5 (.73) 19.4 (.76) 10.8 (.43) 11.7 (.46) 14.7 (.58) 15.6 (.61) 15.7 (.62) 16.6 (.65) 19.5 (.77) 20.4 (.80) 19.5 (.77) 20.4 (.80) 11.8 (.46) 12.7 (.50) 15.7 (.62) 16.6 (.65) 16.7 (.66) 17.6 (.69) 20.5 (.81) 21.4 (.84) 20.5 (.81) 21.4 (.84) 12.8 (.50) 13.7 (.54) 16.7 (.66) 17.6 (.69) 17.7 (.70) 18.6 (.73) 21.5 (.85) 22.4 (.88) 21.5 (.85) 22.4 (.88) 13.8 (.54) 14.7 (.58) 17.7 (.70) 18.6 (.73) 18.7 (.74) 19.6 (.77) 22.5 (.89) 23.4 (.92) 22.5 (.89) 23.4 (.92) 14.8 (.58) 15.7 (.62) 18.7 (.74) 19.6 (.77) 19.7 (.78) 20.6 (.81)
www.southco.com/D8
294
Rivet-On
25 (.984) 12 (.412) 3.3 (.130) Two places 20 (.787) 33 (1.30)
Gasket
82 85 D8 D1 D4 D7 NY
Installation Notes
Install with 3 (.125) rivets
8.3 (.327)
F TMT TMT = P + F
F TMT
F TMT
Part Number
See table ACTUAL SIZE
11.00 (.433) 3.60 (.142) 25.00 (.984)
Notes
Utilize stud selection column indicated when choosing a stud length from the stud length table on page 293
Weld-On
25 (.984) 12 (.472)
Gasket
20 (.787)
Part Number
See table
ACTUAL SIZE
Notes
Utilize stud selection column indicated when choosing a stud length from the stud length table on page 293
Part Number
D8-336-500-121
Side Mount
15.2 (.598) P 33 (1.30) TMT TMT = P + 1.90 (.075)
14.8 (.583)
Part Number
See table
1.2 (.047)
23 (.906)
Notes
Utilize stud selection column indicated when choosing a stud length from the stud length table on page 293
ACTUAL SIZE
Part Number
D8-336-310-121
www.southco.com/D8
295
Clip-On
9.3 (.366) 25 (.984) 15.8 (.622)
Gasket P
ACTUAL SIZE
82 85 D8
P F TMT TMT = P + F + Compressed gasket TMT = P + F F TMT F TMT TMT = P + F + 0.8 (0.31)
25 (.984)
Part Number
See table
D1 D4 D7 NY
Notes
Utilize stud selection column indicated when choosing a stud length from the stud length table on page 293
Part Number
11.00 (.433) Min. D8-336-300-121
Clip-On - Mini
8.6 (.339) 12.3 (.484) 8.8 (.346) P 13.10 (.516) Min. 8.00 (.315) Max. Frame thickness 0.9 (.035) to 2.5 (.098) 24 (.945)
Gasket
ACTUAL SIZE
F TMT TMT = P + F
F TMT
Part Number
See table
Notes
Utilize stud selection column indicated when choosing a stud length from the stud length table on page 293
Stainless steel
Front Mount
0.5 (.020) 16.5 (.650) 13.6 (.535)
16.5 (.650)
P TMT TMT = P + Compressed gasket Press & turn Installed position TMT = P + F
F TMT
F TMT
Part Number
See table
Notes
Utilize stud selection column indicated when choosing a stud length from the stud length table on page 293
Part Number
D8-336-200-190
www.southco.com/D8
296
Gasket
82 85 D8 D1 D4 D7 NY
Installation Notes
Press receptacle ush to frame
Notes
Receptacle shown installed ush to the frame. To eliminate the gap between the frame and outer panel, install to a depth the thickness of the selected retainer. This depth should be added to the TMT.
F TMT TMT = P
Solid Install
Outer panel
Blind Install
Part Number
See table
+0.1
Retainer
Notes
Utilize stud selection column indicated when choosing a stud length from the stud length table on page 293
Part Number
D8-336-100-300
Press-In - Self-Clinching
Side view 16.3 (.642) 9.9 (.390) Top view 13.5 (.531) Gasket P P
Installation Notes
See page 497 for installation guidelines
ACTUAL SIZE
P Edge of hole must be sharp on this side. Do not chamfer. 1.30 (.051) Min. frame thickness
F TMT TMT = P + F
F TMT
F TMT
Part Number
See table
Notes
Utilize stud selection column indicated when choosing a stud length from the stud length table on page 293
Part Number
D8-336-110-190
www.southco.com/D8
297
Cupped Washer
1 (.039)
Ejector Spring
11.43 (.45) Max. 0.6 (.022) 14 (.551) 24.13 (.95) 7.62 (.30)
Accessories
When using the ejecting version add 2 (.079) to your TMT
82 85 D8 D1 D4 D7 NY
12.5 (.49)
11.75 (.46)
3.5 (.14)
Notes
Cupped washer only available for tool recess head styles (slot, Phillips, hex, tamper resistant) Assembly consists of spring, cup and stud ordered separately, shipped bulk
L
9 (.354)
Type
Push-on plastic Push-on Cupped washer Ejector spring
Part Number
D8-326-100-040 D8-326-101-200 D8-376-001-049 D4-EHF5-3-950QA
Material
High density polyethylene, black Stainless steel Thermoplastic, black Stainless steel
Adjustment Value
Included in TMT calculation Add 1.00 (.039) Add 1.00 (.039)
Part Number
See table
Steel retainer
Steel retainer
Part Number
X D8-326-200-200 D8-326-201-200
H
48 (1.89) 25 (.98)
X Min.
19 (.75) 5 (.197)
X Max.
44 (1.73) 21 (.83)
www.southco.com/D8
298
82 85 D8 D1 D4 D7 NY
Hex Recess
18 (.71)
Phillips Recess
18 (.71) No. 3 Phillips 4.3 (.17) L
ACTUAL SIZE
ACTUAL SIZE
ACTUAL SIZE
www.southco.com/D8
299
82 85 D8 D1 D4
To select correct fastener: 1. Select receptacle
Choose a receptacle from pages 300 - 302
D8 - 319 - H K - F
D7 NY
Stud Length Table A TMT Range For: D8-339-400-121 D8-339-500-121 D8-339-300-121 D8-339-301-121 D8-339-305-121
Min. 3.0 (.12) 4.0 (.16) 5.0 (.20) 6.0(.24) 7.0 (.28) 8.0 (.31) 9.0 (.35) 10.0 (.39) 11.0 (.43) 12.0 (.47) 13.0 (.51) 14.0 (.55) 15.0 (.59) 16.0 (.63) 17.0 (.67) 18.0 (.71) 19.0 (.75) 20.0 (.79) 21.0 (.83) 22.0 (.87) Max. 3.9 (.15) 4.9 (.19) 5.9 (.23) 6.9 (.27) 7.9 (.31) 8.9 (.35) 9.9 (.39) 10.9 (.43) 11.9 (.47) 12.9 (.51) 13.9 (.55) 14.9 (.59) 15.9 (.63) 16.9 (.67) 17.9 (.70) 18.9 (.74) 19.9 (.78) 20.9 (.82) 21.9 (.86) 22.9 (.90) ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ 2.5 (.10) 3.5 (.14) 4.5 (.18) 5.5 (.22) 6.5 (.26) 7.5 (.30) 8.5 (.33) 9.5 (.37) 10.5 (.41)
Min.
Max. ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ ~ 3.4 (.13) 4.4 (.17) 5.4 (.21) 6.4 (.25) 7.4 (.29) 8.4 (.33) 9.4 (.37) 10.4 (.41) 11.4 (.45) 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 11 (.433) 12 (.472) 13 (.512) 14 (.551) 15 (.591) 16 (.630) 17 (.669) 18 (.709) 19 (.748) 20 (.787) 21 (.827) 22 (.866) 23 (.906) 24 (.945) 25 (.984) 26 (1.02) 27 (1.06) 28 (1.10) 29 (1.14) 30 (1.18)
Notes
Stainless steel material may require a higher minimum order quantity. Contact Southco for details.
www.southco.com/D8
300
Rivet-On
10 (.394) 15.5 (.610) 30 (1.18) 3.3 (.130) Two places 25 (.984) 40 (1.57)
P F TMT TMT = P + F F TMT F TMT Gasket P P
82 85 D8 D1 D4 D7 NY
Installation Notes
Install with 3 (.125) rivets
ACTUAL SIZE
Part Number
See table
Notes
Utilize stud selection column indicated when choosing a stud length from the stud length table on page 299
Part Number
3.60 (.142) D8-339-400-121
Weld-On
10 (.394) 15.5 (.610) 6.3 (.25) Two places 25 (.984) 40 (1.57) P F TMT TMT = P + F F TMT F TMT TMT = P + F + 1 (.039) Gasket P
30 (1.18)
ACTUAL SIZE
Part Number
See table
Notes
Utilize stud selection column indicated when choosing a stud length from the stud length table on page 299
14.00 (.551)
Part Number
D8-339-500-121
www.southco.com/D8
301
Side Mount
16.7 (.657) 42 (1.65) P
82 85 D8 D1 D4 D7
17.5 (.689)
23 (.906)
ACTUAL SIZE
NY
Part Number
See table
Notes
Part Number
D8-339-305-121
Utilize stud selection column indicated when choosing a stud length from the stud length table on page 299
Clip-On
H 30 (1.18)
Gasket
30.8 (1.21) P F TMT TMT = P + F + Compressed gasket 13.00 (.511) Max. TMT = P + F F TMT F TMT TMT = P + F + 2.10 (.083)
F Frame thickness
ACTUAL SIZE
14.00 (.551) Min.
Part Number
See table
Notes
F Frame Thickness Range
0.7 - 3.2 (.028 - .126) 3.2 - 5.5 (.126 - .217)
Part Number
D8-339-300-121 D8-339-301-121
H
10.7 (.421) 11.3 (.445)
Utilize stud selection column indicated when choosing a stud length from the stud length table on page 299
www.southco.com/D8
302
Front Mount
Gasket 16.6 (.654) P P
82 85 D8 D1 D4 D7 NY
21 (.827) 0.8 (.031) 21 (.827)
F TMT TMT = P
F TMT
ACTUAL SIZE
+ 0.20
Installed position
Part Number
See table
Type
Front mount
Part Number
D8-339-200-190
Notes
Utilize stud selection column indicated when choosing a stud length from the stud length table on page 299
www.southco.com/D8
303
82 85
15.8 (.622)
ACTUAL SIZE
Part Number
D8-329-100-040 D8-329-101-200
17 (.669)
D8 D1
Adjustment Value
Included in TMT calculation
Type
Push-on Plastic Push-on
Material
Nylon 6/6 Black Stainless steel
D4 D7 NY
Steel retainer
Part Number
X D8-329-200-200
H
48 (1.89)
X Min.
7 (.276)
X Max.
43 (1.69)
www.southco.com/D8
497
Self-Clinching products
Rollover
When pressed into a properly prepared hole, self-clinching captive fasteners cold-ow (move) the panel material the retaining Centerlineinto of mounting hole groove of 1.5 x Min. the fastener. This material then retains the fastener in the panel.
Before installation Ferrule Correct installation Ferrule Panel Over installation Ferrule
- Installing too close to the edge will cause the material to ow in the Panel Die install side closer opposite Mounting direction, deforming the edge of the panel. To hole of panel to the edge, you may need to restrain the panel edge.
Panel edge Mounting hole diameter Panel
Panel
Material: The hardness of the panel material must not exceed SOUTHCO recommendations. If the panel is too hard, the fastener will not install correctly.
This area of material Before installation Correct installation Over installation has separated from The thickness of the panel at the mounting hole location must meet or Ferrule Ferrule Ferrule the rest of the panel exceed Southcos stated minimum recommendations. Panel Panel
Panel Thickness:
1.5 x Min.
If the material is too thin, panel deformation and/or damage to the fastener may result.
Installation Holes: Mounting holes may be drilled, punched, or cast. Punch Hole edge: the top holeside edge must Ferrule of panel Rollover Area of material be sharp but with no broken edges. that moves into Do not chamfer or debur Material edge. groove thickness Punched holes: use a punch and die Panel Die side with a small clearance to minimize Mounting hole of panel the rollover and fracture angle. Mounting hole Hole diameter: measure the hole Punch side diameter of panel diameter at the panel surface on Rollover Panel edge Panel of material moves into the side on which the fastener will Material e thickness Centerline beof installed. The diameter must be mounting hole 1.5 x Min. l Die side within SOUTHCO specications for of panel installation that product. Over installation Before installation Correct Ferrule Ferrule Ferrule If the hole is too large, not enough material will ow into the ounting hole Panel Panel diameter retaining groove and the fastener may not be retained adequately. Panel - If the hole is too small, the fastener will not t and installation may become difcult and unsafe. Centerline of mounting hole This area of material Min. Hole distance from the edge of panel: the minimum has recommended separated from the rest of the panel distance is 1.5 x the diameter of the mounting hole, unless Correct installation Over installation otherwise indicated. Ferrule Ferrule Panel Panel
Installation is fast and easy if you follow these tips: This area of material has a separated How to install: Use the recommended force where noted and proper from the rest of the panel back-up tool. - use any parallel-acting press - use a punch whose diameter is larger than the head of the fastener Installation Force: Proper installation requires an even distribution of adequate force. It does not depend on the distance Punch the fastener is side Ferrule into the panel. pressed of panel Rollover Area of material - Southco does not recommend using a hammer. TheMaterial impact force that moves into groovean even distribution of force to allow does not provide the panel thickness material to completely ow into the fasteners retaining groove. Panel Die side - Installation Mountingforce hole varies from application to application, of panel depending on the criteria noted above. - On parts without a collar to provide a hard stop, press-in until the Mounting hole edge of the knurldiameter is just barely visible. When to Install: Installation is recommended after plating or nishing Centerline of mounting hole has been applied to 1.5 x Min. the panel. The hole diameter must meetCorrect specications Before installation installation Over installation before nish or plating is applied. Ferrule Ferrule Ferrule Panel Panel - Do not over-install parts. This interupts the material and will reduce the retention strength.
This area of material has separated from the rest of the panel Panel edge Panel
This area of material has separated from the rest of the panel