Вы находитесь на странице: 1из 27

Sabarmati River Front Development Corporation Limited

Electrical Work BOQ : 1 of 27

Section VII : Bills of Quantity 7.3 : Electrical work


Electrical Works AMOUNT

1 2 3 4 5 6 7 8 9 10

Section Feeder Panels Point wiring & Distribution board Cable Trenches, Manholes & Pipes MV Cabling & Wires Cable Connections Street Light Poles & High Mast Light Fixtures Earthing P.A. system Miscellaneous Total For Electrical Works

Signature and stamp of Bidder

Sabarmati River Front Development Corporation Limited

Electrical Work BOQ : 2 of 27

SR. NO. 1

DESCRIPTION Section Feeder Panels Supplying, unloading at site, shifting to site, assembling, leveling, grouting, erecting, Testing, & Commissioning double compartmentalized Street light control panel with IP 65 protection & Enclauser should be powder coated fabricated from 10 Guage M.S. sheet & folded channel totally enclosed cubical type with made out of Modular Panel Box System, Degree of Protection IP 65, in accordance with IEC 60 529, type tested in accordance with IEC 60 439 1. with pad lock arrangment. The successful tenderer will have to prepare general arrangement with dimensions & get it approve through Architect/ Consultant. All civil work including RCC platform for street light panel should be in scope of Electrical contractor complete in all respect as per detail drawing and directed by engineer incharge. with the 600 mm height MS angle covered stand. ( From Reputed manufacture / CPRI Approved Panel Builder Only ) ( GA Drawing will be approved by Design Consultant )

UNIT

QTY

RATE SUPPLY ITC TOTAL

TOTAL RATE IN WORDS

AMOUNT

The panel board shall be made up of high quality polycarbonate thermoplastic, shock proof, anti-corrosive, acid & chemical resistant, fire retardant, self extinguishing, highly impact resistant, halogen free, silicon free, recyclable, having internally embedded gasket. The switchboard (panel) shall have provision for future expansion & shall be modular in construction. The bus bars shall be connected with C type clamps without any drilling on the bus bars. The panel shall be in accordance with IEC 60 439 1 (Fully TTA). The Degree of Ingress Protection shall be in accordance with IEC 60 529. & As per specifications

Signature and stamp of Bidder

Sabarmati River Front Development Corporation Limited

Electrical Work BOQ : 3 of 27

SR. NO. 1.1

DESCRIPTION SITC of the IP 65 Section feeder panel for the Street Lighting Consisting of following Incoming : 125 Amp FP SFU with the spreader link R-Y-B-On-Off indicating Lamp with control fuse. Busbar : Set of 125 A. FP tinned copper busbars of EC. grade & adequate capacity, size & insulated with color tape & should be tined at all joints. Auto/Manual bypass switch with indicating lamp Meter : VAF meter equivalent to Enercon make ELF 3259 with 125/ 5 A Class 1 ct. Outgoing : MCB's Should be of 10 KA. Dual Channel Astronomical Timer Equivalent to Legrand make Cat. No. 04767 with the battery back up : 4 nos. 40 amp. FP Power Contactor : 4 nos. 6 - 32 amp. DP Power Contactor : 6 nos. 40 Amp. FP MCB : 5 nos. 6 -32 Amp. FP MCB : 4 nos. 6 - 32 amp. SP MCB : 24 nos. 5 KVAR Capacitor with the 40 amp TP capacitor duty contactor with the 10 minute time delay relay. Panel Should Have lockable Space to incorporate the 2 nos of the 3 phase energy meter with its main switches with separate cable entry & Watch Window.

UNIT no

QTY 10.0

RATE SUPPLY ITC TOTAL

TOTAL RATE IN WORDS

AMOUNT

1.3

SITC of IP66 Water Tight Junction Box 210mm x 260mm x 117mm With necessary clamp for mounting of the J.B. ( All the cable / wire connections to the JB shall be with the Water tight IP 66 Polyamide Glands, open Holes should be sealed with the IP65 Grommets only ) J. B. Should be provided with Hensel make cable connectors to connect 2 nos. of 25 sq. mm. x 4 core cables + Earthing wires. of Hensel make cat. no. KD5355 + Connectors + IP65 Glands + IP65 Grommets

no

100.0

Signature and stamp of Bidder

Sabarmati River Front Development Corporation Limited

Electrical Work BOQ : 4 of 27

SR. NO. 1.4

DESCRIPTION SITC of IP66 Water Tight Junction Box 200mm x 160mm x 98mm With necessary clamp for mounting of the J.B. ( All the cable / wire connections to the JB shall be with the Water tight IP 66 Polyamide Glands, open Holes should be sealed with the IP65 Grommets only ) J. B. Should be provided with Hensel make cable connectors to connect 1 nos. of 10/16 sq. mm. x 4 core cables+ 4-5 nos. of 4 sq. mm x 4 core wires + Earthing wires. of Hensel make cat. no. KD5255 + Connectors + IP65 Glands + IP65 Grommets SITC of IP66 Water Tight Junction Box 167mm x 125mm x 82mm With necessary clamp for mounting of the J.B. ( All the cable / wire connections to the JB shall be with the Water tight IP 66 Polyamide Glands, open Holes should be sealed with the IP65 Grommets only ) J. B. Should be provided with Hensel make cable connectors to connect 1 nos. of 6/10 sq. mm. x 4 core cables+ 4-5 nos. of 4 sq. mm x 4 core wires + Earthing wires. of Hensel make cat. no. KD5105 + Connectors + IP65 Glands + IP65 Grommets SITC of IP66 Water Tight Junction Box 139mm x 115mm x 70mm With necessary clamp for mounting of the J.B. ( All the cable / wire connections to the JB shall be with the Water tight IP 66 Polyamide Glands, open Holes should be sealed with the IP65 Grommets only ) J. B. Should be provided with Hensel make cable connectors to connect 1 nos. of 6/10 sq. mm. x 4 core cables+ 4-5 nos. of 4 sq. mm x 4 core wires + Earthing wires. of Hensel make cat. no. KD5065 + Connectors + IP65 Glands + IP65 Grommets Sub Total 1 .....

UNIT no

QTY 200.0

RATE SUPPLY ITC TOTAL

TOTAL RATE IN WORDS

AMOUNT

1.5

no

50.0

1.6

no

50.0

Signature and stamp of Bidder

Sabarmati River Front Development Corporation Limited

Electrical Work BOQ : 5 of 27

SR. NO. 2

DESCRIPTION Internal Wiring Supply, installation, connection, testing & commissioning of following outlet points as per Specification & IS. The unit rate for the point shall consist of the circuit wiring from LDB or switch board to outlet point through MCB / switch as required & including the outlet points with connector & sockets. A point shall include in addition to phase & neutral wire, earth continuity wire from LDB to the final termination at outlet points as per specification.

UNIT

QTY

RATE SUPPLY ITC TOTAL

TOTAL RATE IN WORDS

AMOUNT

All the wiring, outlet points shall be done in a surface / concealed manner with ISI approved medium duty, rigid FR PVC, ISI conduit of minimum 25 mm. dia. using 650 V FRLS copper conductor wire, modular switches with suitable plate, PVC / Metal back box with brass chromium / cadmium plated machine screws etc.

2.1 Point Wiring 2.1.1 Wiring for the following light points with 1.5 sq.mm FRLS flexible copper conductor 1100 volts grade wires of approved make in concealed or surface mounted 25 mm dia medium gauge PVC Conduit including providing and fixing of 6 amps single pole rocker operated flush mounted switch of approved quality color make & design in 2 mm thick GI box and earthing of fixtures and the outlet box with 1.5 sq.mm PVC insulated copper conductor stranded flexible "FRLS" wire. a b c Primary Light point controlled by one single way 6 A switch. Primary light point controlled by one SP MCB no no no 75.0 20.0 125.0

Secondary light point controlled by same switch / MCB

Signature and stamp of Bidder

Sabarmati River Front Development Corporation Limited

Electrical Work BOQ : 6 of 27

SR. NO. 2.1.2 Wiring

DESCRIPTION

UNIT no

QTY 50.0

RATE SUPPLY ITC TOTAL

TOTAL RATE IN WORDS

AMOUNT

for the Ceiling Fan points with 1.5 sq.mm FRLS flexible copper conductor 1100 volts grade wires of approved make in concealed or surface mounted 25 mm dia medium gauge PVC Conduit including providing fan hook box, 6 amps switch and 300 watts electronic hum free fan regulator of approved quality color make & design in 2 mm thick GI box and earthing of fixtures and the outlet box with 1.5 sq.mm PVC insulated copper conductor stranded flexible "FRLS" wire. 2.1.3 Wiring for the 250 volts single phase and neutral 6 amps switched socket outlet with 2.5 sq.mm FRLS flexible copper conductor 1100 volts grade wires of approved make in concealed or surface mounted 25 mm dia medium gauge PVC Conduit including providing and fixing of 6 amps 5 pin switch socket outlet of approved quality color make & design in 2 mm thick GI box and earthing of fixtures and the outlet box with 1.5 sq.mm PVC insulated copper conductor stranded flexible "FRLS" wire.
a b One 6 A x 5 pin 250 Volt socket outlet point controlled by one 6 A switch located on board. 6 A x 5 pin 250 Volt switched socket outlet point at convenient location.

no no

50.0 75.0

Signature and stamp of Bidder

Sabarmati River Front Development Corporation Limited

Electrical Work BOQ : 7 of 27

SR. NO. 2.1.4 Wiring

DESCRIPTION

UNIT no

QTY 25.0

RATE SUPPLY ITC TOTAL

TOTAL RATE IN WORDS

AMOUNT

for the 250 volts single phase and neutral 16 amps switched socket outlet with 2.5 sq.mm FRLS flexible copper conductor 1100 volts grade wires of approved make in concealed or surface mounted 25 mm dia medium gauge PVC Conduit including providing and fixing of 16 amps 5 pin switch socket outlet of approved quality color make & design in 2 mm thick GI box and earthing of fixtures and the outlet box with 1.5 sq.mm PVC insulated copper conductor stranded flexible "FRLS" wire.

2.1.5 DO - as 2.1.4 but with4 sq.mm wire for phase & Neutral & 2.5 sq. mm for Earthing 2.1.6 Wiring for the Exhaust fan point with 1.5 sq.mm FRLS flexible copper conductor 1100 volts grade wires of approved make in concealed or surface mounted 25 mm dia medium gauge PVC Conduit including providing and fixing of 6 amps flush mounted switch at the normal switch level in 2 mm thick GI box and 6 amps 3 pin flush mounted socket out of near exhaust fan and earthing of exhaust fan through the third pin of the socket outlet of approved quality color make & design in 2 mm thick GI box and earthing of fixtures and the outlet box with 1.5 sq.mm PVC insulated copper conductor stranded flexible "FRLS" wire.

no no

25.0 20.0

2.1.7 Supply and laying of 25 mm rigid PVC pipe of 1.6-1.8 mm thickness 2.2 Distribution Board-TPN 2.2.1 Supply, Erecting, testing and commissioning of only TPN D.B. PPI type with space for FPMCB as incoming and space for DPELMCB and 12 SPMCB as outgoing per phase (i.e. 16 way per phase D.B.) of Hensel Make KV9448M

mtr

2,500.0

no

2.0

Signature and stamp of Bidder

Sabarmati River Front Development Corporation Limited

Electrical Work BOQ : 8 of 27

SR. NO.

DESCRIPTION

UNIT no

QTY 1.0

RATE SUPPLY ITC TOTAL

TOTAL RATE IN WORDS

AMOUNT

2.2.2 Supply, Erecting, testing and commissioning of only TPN D.B. PPI type with space for FPMCB as incoming and space for DPELMCB and 8 SPMCB as outgoing per phase (i.e. 12 way per phase D.B.) of Hensel Make KV9448M 2.2.3 Supply, Erecting, testing and commissioning of only TPN D.B. PPI type with space for FPMCB as incoming and space for DPELMCB and 4 SPMCB as outgoing per phase (i.e. 8 way per phase D.B.) of Hensel Make KV9336M 2.2.4 Supply, Erecting, testing and commissioning of only TPN D.B. PPI type with space for FPMCB as incoming and space for DPELMCB and 2 SPMCB as outgoing per phase (i.e. 6 way per phase D.B.) of Hensel Make KV9224M 2.3 Distribution Board-SPN 2.3.1 Supply, Erecting, testing and commissioning of SPN D.B. PPI type with space for DPELMCB as incoming and 12 SPMCB as outgoing per phase (i.e. 16 way D.B.) of Hensel Make KV9118M 2.3.2 Supply, Erecting, testing and commissioning of SPN D.B. PPI type with space for DPELMCB as incoming and 8 SPMCB as outgoing per phase (i.e. 12 way D.B.) of Hensel Make KV9112M 2.3.3 Supply, Erecting, testing and commissioning of SPN D.B. PPI type with space for DPELMCB as incoming and 4 SPMCB as outgoing per phase (i.e. 8 way D.B.) of Hensel Make KV7109M 2.3.4 Supply, Erecting, testing and commissioning of SPN D.B. PPI type with space for DPELMCB as incoming and 2 SPMCB as outgoing per phase (i.e. 6 way D.B.) of Hensel Make KV7106M 2.3.5 2.3.6 2.3.7 2.3.8 2.3.9 2.3.10 2.3.11 2.3.12 6-32 Amp. SP MCB 6-32 Amp. DP MCB 25 A / 100 mA DP ELMCB 32 A / 100 mA DP ELMCB 40 A / 100 mA DP ELMCB 6-32 Amp. FP MCB 40 Amp. FP MCB 20 Amp. DP din Rail Mounted Power Contactor

no

1.0

no

1.0

no

4.0

no

20.0

no

3.0

no

3.0

no no no no no no no no

350.0 50.0 10.0 35.0 15.0 10.0 10.0 10.0

Signature and stamp of Bidder

Sabarmati River Front Development Corporation Limited

Electrical Work BOQ : 9 of 27

SR. NO.

DESCRIPTION

UNIT no no

QTY 10.0 10.0

RATE SUPPLY ITC TOTAL

TOTAL RATE IN WORDS

AMOUNT

2.3.13 40 Amp. FP din Rail Mounted Power Contactor 2.3.14 Supplying & erecting approved make Digital time switch having minimum lithium cell 6 years operative and operate battery backup 1 channel day clock with 14 memory programme, suitable to operate on 240V + 5%, 16A with, floating contacts Minimum switching setup time 1 minimum & LCD display. Also comprised permanent ON/OFF switching. Programming switches & housed in fire proof thermoplastic enclosure & transparent cover erected as required with necessary connection. Dual Channel Timer Equivalent to Legrand make Cat. No. 04767 2.3.15 10A x 250 Volt single phase Power socket outlet point having IP rating of IP:65 at convenient location with MCB.for outdoor duty. 2.3.16 20A x 250 Volt single phase Power socket outlet point having IP rating of IP:65 at convenient location with MCB.for outdoor duty. 2.3.17 32A x 415 Volt three phase Power socket outlet point having IP rating of IP:65 at convenient location with MCB.for outdoor duty. 3.0 3.1 Sub Total 2 ..... Cable Trenches, Manholes & Pipes Making trench in soft soil of suitable width of 90 cms deep from the final ground level or road level for laying cable or locating the fault all over the run and backfilling the same & clearing the site by removing debris & Shifting of the debris & making site good As per the Instruction of the Engineer In charge. Covering of cable with second class bricks laid cover the cable crosswise & also on both sides with covering of 7. 5 Cms. layer of sand above & below cable (cable shall be laid in 0.9mtr.deep & 0.4 Mtr.wide trench). Where there are more than one cable in the trench on either side of the cable, 5 Cms. over lapping of bricks shall be provided.

no

5.0

no

5.0

no

5.0

mt

5,000.0

3.2

mt

1,000.0

Signature and stamp of Bidder

Sabarmati River Front Development Corporation Limited

Electrical Work BOQ : 10 of 27

SR. NO. 3.3

DESCRIPTION Drilling the road without breaking the road surface (Asphalt) for laying of cable for feeding power supply by making Suitable size of holes at both ends complete.

UNIT mt

QTY 100.0

RATE SUPPLY ITC TOTAL

TOTAL RATE IN WORDS

AMOUNT

3.4

Providing cement concrete.for foundation or for concrete Cu. Mtr. filling in M20 Grade Cement Concrete duly plastered with necessary curing for pole muffing or any other purpose. Scope includes all necessary digging & Backfilling. Construction of brick masonry pulling chamber 600 mm x 600 mm inside clear size and depth up to 0.6 meter with 230 mm thick masonry in cement mortar proportion 1:5,cement finish cement plaster in CM proportion of 15 mm thickness from inside with 150 mm thick PCC at bottom with top slab minimum 200 mm thickness in M20 grade with reinforcement. The rate shall be inclusive of providing and fixing frame and 600 mm dia cover of FRC for the Heavy Duty. Rate also inclusive of excavation and back filling & clearing the site by removing debris & Shifting of the debris & making site good As per the Instruction of the Engineer In charge complete in all respect. Construction of brick masonry pulling chamber 750 mm x 750 mm inside clear size and depth up to 1.25 meter with 350 mm thick masonry in cement mortar proportion 1:5,cement finish cement plaster in CM proportion of 15 mm thickness from inside with 150 mm thick PCC at bottom with top slab minimum 200 mm thickness in M20 grade with reinforcement. The rate shall be inclusive of providing and fixing frame and 900 mm dia cover of FRC for the Heavy Duty. Rate also inclusive of excavation and back filling & clearing the site by removing debris & Shifting of the debris & making site good As per the Instruction of the Engineer In charge complete in all respect. no

5.0

3.5

5.0

3.6

no

5.0

Signature and stamp of Bidder

Sabarmati River Front Development Corporation Limited

Electrical Work BOQ : 11 of 27

SR. NO. 3.7

DESCRIPTION Construction of brick masonry pulling chamber 1000 mm x 1000 mm inside clear size and depth up to 1.75 meter with 350 mm thick masonry in cement mortar proportion 1:5,cement finish cement plaster in CM proportion of 15 mm thickness from inside with 150 mm thick PCC at bottom with top slab minimum 200 mm thickness in M20 grade with reinforcement. The rate shall be inclusive of providing and fixing frame and 900 mm dia cover of FRC for the Heavy Duty. Rate also inclusive of excavation and back filling & clearing the site by removing debris & Shifting of the debris & making site good As per the Instruction of the Engineer In charge complete in all respect. Construction of brick masonry pulling chamber 1250 mm x 1250 mm inside clear size and depth up to 1.75 meter with 350 mm thick masonry in cement mortar proportion 1:5,cement finish cement plaster in CM proportion of 15 mm thickness from inside with 150 mm thick PCC at bottom with top slab minimum 200 mm thickness in M20 grade with reinforcement. The rate shall be inclusive of providing and fixing frame and 1000 mm dia cover of FRC for the Heavy Duty. Rate also inclusive of excavation and back filling & clearing the site by removing debris & Shifting of the debris & making site good As per the Instruction of the Engineer In charge complete in all respect. Providing & laying. R.C.C. hume pipe N.P. 2 class for cable to be laid 90 cms. below ground across the road crossing or on floor with necessary material in an approved manner (A) 250 mm dia (B)150 mm dia (C) 200 mm dia.

UNIT no

QTY 5.0

RATE SUPPLY ITC TOTAL

TOTAL RATE IN WORDS

AMOUNT

3.8

no

5.0

3.9

mt mt mt

50.0 50.0 50.0

Signature and stamp of Bidder

Sabarmati River Front Development Corporation Limited

Electrical Work BOQ : 12 of 27

SR. NO.

DESCRIPTION

UNIT

QTY

RATE SUPPLY ITC TOTAL

TOTAL RATE IN WORDS

AMOUNT

3.10 Providing & laying Double walled corrugated pipes (DWC) of polyethylene(conforming to IS 14930 II ) with necessary connecting accessories of same material at 0.7 mtr. depth for laying of cable. below ground / road surface for enclosing cable and including digging the ground & backfilling the same to make ground as per original. (A)50 mm dia (B)90 mm dia (C)120 mm dia. 3.11 Supplying & Fixing of following sizes 2 mm thick and ISI mark (embossed) RIGID PVC Conduit along with accessories & Continuous fish wire in surface / Recess / in Ground including cutting the wall and making good the same in case of recess conduit if required. including digging the ground & backfilling the same to make ground as per original. (A) 20mm (B) 25mm (C) 32mm (D) 40mm Sub Total 3..... Cables Supply and Laying XLPE(IS:7098) )(I)-88 ISI marked armored cable of Cu. / Aluminum conductor of 1.1 KV.grade of following sizes in ground or in pre-laid DWC pipe / Trenches with necessary cable identification mark to be provided at distance of 15 mt. & with 2 nos. of 16 SWG G.I. wire continuous in length per cable. 35 sq.mm x 3.5 c Al. cable 25 sq.mm x 4 c Al. cable 16 sq.mm x 4 c Al. cable 10 sq.mm x 4 c Al. cable 6 sq.mm x 4 c Al. cable 6 sq.mm x 4 c Cu. cable 4 sq.mm x 4 c Cu. cable 4 sq.mm x 3 c Cu. cable mt mt mt 10,000.0 3,000.0 2,000.0

mt mt mt mt

5,000.0 10,800.0 2,000.0 3,500.0

4.0 4.1

4.1.1 4.1.2 4.1.3 4.1.4 4.1.5 4.1.6 4.1.7 4.1.8

mt mt mt mt mt mt mt mt

50.0 500.0 3,500.0 3,500.0 3,000.0 750.0 750.0 1,000.0

Signature and stamp of Bidder

Sabarmati River Front Development Corporation Limited

Electrical Work BOQ : 13 of 27

SR. NO. 4.2

DESCRIPTION Supplying and laying Flexible FR PVC insulated multistrand multicore 1.1 kv grade ISI marked copper wires of following size in HMS PVC Pipe. 1.00 Sq.mm 4 core round PVC sheathed 1.50 Sq.mm 3 core round PVC sheathed 2.50 Sq.mm 3 core round PVC sheathed 4.00 Sq.mm 3 core round PVC sheathed 6.00 Sq.mm 3 core round PVC sheathed Sub Total 4..... Cable Termination Supplying & fixing of Thermoplastic glands (IP65) of Spelsberg or Hensel make & making joint with necessary crimping socket of long nack type connecting the same to various equipment etc. for the following sizes:

UNIT

QTY

RATE SUPPLY ITC TOTAL

TOTAL RATE IN WORDS

AMOUNT

4.2.1 4.2.2 4.2.3 4.2.4 4.2.5 5.0

mt mt mt mt mt

1,000.0 5,000.0 5,000.0 4,000.0 2,000.0

35 sq.mm x 3.5 c Al. cable 25 sq.mm x 4 c Al. cable 16 sq.mm x 4 c Al. cable 10 sq.mm x 4 c Al. cable 6 sq.mm x 4 c Al. cable 6 sq.mm x 4 c Cu. cable 4 sq.mm x 4 c Cu. cable 4 sq.mm x 3 c Cu. cable Sub Total 5..... 6.0 Street light Poles 6.1 Street Light Poles 6.1.1 Supply & installation of decorative Column of 4.1 mtr height above the ground level primered & painted as per the approved color & Shade - minimum 2 coats PU based MRF Paint Factory Finish. The column shall also be provided with flush door at the bottom with proper strengthening to the cutout of the door opening. A junction/ looping box with 32 Amps heavy duty connector shall be built into the pole. street light pole with Single Arm Bracket / arrangement for the top mounting fixture as per drawing. 1) 8 way connector and 6A MCB 2) 50 mm diameter DWC pipe for each cable entry. Pipe length is up to 3.5 mtr. Per cable

5.1 5.2 5.3 5.4 5.5 5.6 5.7 5.8

no no no no no no no no

10.0 50.0 400.0 400.0 250.0 100.0 100.0 100.0

no

225.0

Signature and stamp of Bidder

Sabarmati River Front Development Corporation Limited

Electrical Work BOQ : 14 of 27

SR. NO.

DESCRIPTION 3) Wiring up to the light fixture from the junction box using 3core x 1.5 sq.mm. flexible copper wires per Fixture of specified make. 4) 1 mtr. depth M20 grade Concrete coping with 0.6 mtr. foundation bolt with base plate with stiffener as per drawing. 5) Spiral/Coil Type Earthing from the 6 swg G.I. Wire of 2.5 mtr. With the suitable size pipe with clamps and painting. 6) Radium strip of two color at suitable height 7) Excavation & back filling for erection of poles. Debris to be removed from the site to suitable location as per the instruction of the engineer in charge

UNIT

QTY

RATE SUPPLY ITC TOTAL

TOTAL RATE IN WORDS

AMOUNT

6.1.2 Supply & installation of decorative Column of 5.1 mtr height above the ground level primered & painted as per the approved color & Shade - minimum 2 coats PU based MRF Paint Factory Finish. The column shall also be provided with flush door at the bottom with proper strengthening to the cutout of the door opening. A junction/ looping box with 32 Amps heavy duty connector shall be built into the pole. street light pole with Single Arm Bracket / arrangement for the top mounting fixture as per drawing. ( Type 1 Pole ) 1) 8 way connector and 6A MCB 2) 50 mm diameter DWC pipe for each cable entry. Pipe length is up to 3.5 mtr. Per cable 3) Wiring up to the light fixture from the junction box using 3core x 1.5 sq.mm. flexible copper wires per Fixture of specified make. 4) 1 mtr. depth M20 grade Concrete coping with 0.6 mtr. foundation bolt with base plate with stiffener as per drawing. 5) Spiral/Coil Type Earthing from the 6 swg G.I. Wire of 2.5 mtr. With the suitable size pipe with clamps and painting. 6) Radium strip of two color at suitable height

no

25.0

Signature and stamp of Bidder

Sabarmati River Front Development Corporation Limited

Electrical Work BOQ : 15 of 27

SR. NO.

DESCRIPTION 7) Excavation & back filling for erection of poles. Debris to be removed from the site to suitable location as per the instruction of the engineer in charge

UNIT

QTY

RATE SUPPLY ITC TOTAL

TOTAL RATE IN WORDS

AMOUNT

6.1.3 Supply & installation of decorative Column of 5.1 mtr height above the ground level primered & painted as per the approved color & Shade - minimum 2 coats PU based MRF Paint Factory Finish. The column shall also be provided with flush door at the bottom with proper strengthening to the cutout of the door opening. A junction/ looping box with 32 Amps heavy duty connector shall be built into the pole. street light pole with Single Arm Bracket / arrangement for the top mounting fixture as per drawing. ( Type 2 Pole ) 1) 8 way connector and 6A MCB 2) 50 mm diameter DWC pipe for each cable entry. Pipe length is up to 3.5 mtr. Per cable 3) Wiring up to the light fixture from the junction box using 3core x 1.5 sq.mm. flexible copper wires per Fixture of specified make. 4) 1 mtr. depth M20 grade Concrete coping with 0.6 mtr. foundation bolt with base plate with stiffener as per drawing. 5) Spiral/Coil Type Earthing from the 6 swg G.I. Wire of 2.5 mtr. With the suitable size pipe with clamps and painting. 6) Radium strip of two color at suitable height 7) Excavation & back filling for erection of poles. Debris to be removed from the site to suitable location as per the instruction of the engineer in charge

no

25.0

Signature and stamp of Bidder

Sabarmati River Front Development Corporation Limited

Electrical Work BOQ : 16 of 27

SR. NO.

DESCRIPTION

UNIT no

QTY 25.0

RATE SUPPLY ITC TOTAL

TOTAL RATE IN WORDS

AMOUNT

6.1.4 Supply & installation of decorative Column of 6.2 mtr height above the ground level primered & painted as per the approved color & Shade - minimum 2 coats PU based MRF Paint Factory Finish. The column shall also be provided with flush door at the bottom with proper strengthening to the cutout of the door opening. A junction/ looping box with 32 Amps heavy duty connector shall be built into the pole. street light pole with Single Arm Bracket / arrangement for the top mounting fixture as per drawing. 1) 8 way connector and 6A MCB 2) 50 mm diameter DWC pipe for each cable entry. Pipe length is up to 3.5 mtr. Per cable 3) Wiring up to the light fixture from the junction box using 3nos x 1.5 sq.mm. flexible copper wires / Fixture of specified make. 4) 1.2 mtr. depth M20 grade Concrete coping with 0.6 mtr. foundation bolt with base plate with stiffener as per drawing. 5) Spiral/Coil Type Earthing from the 6 swg G.I. Wire of 2.5 mtr. With the suitable size pipe with clamps and painting. 6) Radium strip of two color at suitable height 7) Excavation & back filling for erection of poles. Debris to be removed from the site to suitable location as per the instruction of the engineer in charge

Signature and stamp of Bidder

Sabarmati River Front Development Corporation Limited

Electrical Work BOQ : 17 of 27

SR. NO.

DESCRIPTION

UNIT no

QTY 5.0

RATE SUPPLY ITC TOTAL

TOTAL RATE IN WORDS

AMOUNT

6.1.5 Supply & installation of GRP pole with Two Nos.

single arm bracket to be fixed at various height for street light having top 76.0mm O.D. & bottom 277.0 mm O.D. with avg. thickness of 10.0 mm 10 Mtr long ( effective length should be 10 Mtr.above GF) with 1) Water tight Junction box of Hensel make with 8 way connector and 2 nos of 2A MCB 2) 50 mm diameter DWC pipe for each cable entry. Pipe length is up to 3.5 mtr. Per cable. 3) Wiring up to the light fixture from the junction box using 3c x 1.5 sq.mm. flexible copper wires / fixture of specified make. 4) 2 mtr. Depth & 600 mm x 600 mm Concrete coping Concrete coping with base plate with sleeve for pole with stiffener as per drawing. 5) Spiral/Coil Type Earthing 6) Excavation for erection of poles.
6.1.6 Supply & installation of 11Mtr (Approx 36') high (coloured and primered in minimum 2 coats of PU based paint in approved colour and shade) made out of M.S. tubular pole of dia 194 mm top swaged with base plate with stiffner, primered and painted street light pole The column shall also be provided with flush door at the bottom with proper strengthening to the cutout of the door opening. A junction/ looping box with Heavy duty 3 phase connector shall be built into the pole with single arm bracket from the 42 to 60 mm dia pipe with Suitable size of M.S. sleeve /reducer duly welded at the end of the arm, The total play should not be more than 10 mm as per drawing. no 5.0

1) 8 way connector and 6A MCB 2) 50 mm diameter DWC pipe for each cable entry. Pipe length is up to 3.5 mtr. Per cable 3) Wiring up to the light fixture from the junction box using 3nos x 1.5 sq.mm. flexible copper wires / Fixture of specified make. 4) Concrete coping with base plate with stiffner.

Signature and stamp of Bidder

Sabarmati River Front Development Corporation Limited

Electrical Work BOQ : 18 of 27

SR. NO.

DESCRIPTION 5) Sprial/Coil Type Earthing from the 8 swg Cu. Wire of 2.5 mtr. With the suitable size pipe with clamps and painting. 6) Radium stip of two colour at suitable height 7) Excavation & back filling for erection of poles. Debris to be removed from the site to suitable location as per the instruction of the engineer incharge

UNIT

QTY

RATE SUPPLY ITC TOTAL

TOTAL RATE IN WORDS

AMOUNT

6.1.7 SITC of Decorative pole with fixture of Schreder make decorative Sextant Pole 12 m made out of G.I., primered and painted PU factory finish. T. A junction/ looping box with Heavy duty 3 phase connector shall be suitable into the pole along with Sexant Bracket suitable for 3 Luminaire in GI with following 1) 8 way connector and 6A MCB 2) 50 mm diameter DWC pipe for each cable entry. Pipe length is up to 3.5 mtr. Per cable 3) Wiring up to the light fixture from the junction box using 3nos x 1.5 sq.mm. flexible copper wires / Fixture of specified make. 4) M 20 grade Concrete coping with base plate with stiffner. 5) Sprial/Coil Type Earthing from the 8 swg Cu. Wire of 2.5 mtr. With the suitable size pipe with clamps and painting. 6) Radium stip of two colour at suitable height 7) Excavation & back filling for erection of poles. Debris to be removed from the site to suitable location as per the instruction of the engineer incharge Sub Total 6.....

27.0

Signature and stamp of Bidder

Sabarmati River Front Development Corporation Limited

Electrical Work BOQ : 19 of 27

SR. NO. 7.0

DESCRIPTION Light Fixtures Supply, Installation, Testing & Commissioning of the following Light Fixture with lamp, Control Gear & All necessary accessories. Luminaries with all electrical accessories & it should be energy efficient, low loss, ortho cyclically wound open construction copper ballast, ignitor & power factor improvement capacitor or Electronics Ballast etc are prewired up to the terminal block & mounted on a removable control gear module for ease of maintenance. All electrical connections of the control gear module with the rest of the luminaries should be click fix & foolproof & require use of no tools. Mounting options should be for both lateral as well as pole top mounting. with Lamp Control Gear & Fixing Accessories. All the light fixtures will be finally approved by Architect / Consultant. Architect / Consultant reserves the right to reject the fittings suggested by the contractor.

UNIT

QTY

RATE SUPPLY ITC TOTAL

TOTAL RATE IN WORDS

AMOUNT

7.1 7.2 7.3

1 x 28 watt T5 Light fixture with Lamp of Philips make TWG 207 1 x TL5 - 28 watt HF 1 X 11 watt mirolta type Light Fixture of Philips make FMS 200/ 111 1 x 150 watt IP42 Suspended Light fixtures with all necessary hanging arrangement of Philips make Cat. No. MPK 632 C 1 x 150 w CDM-T GR with Glass IP67 Drive over Ground Burial Light fixture with 70 watt CDM-T with Integral Control Gear with Body made of die cast alluminium with 1 / 2 / 12 windows protective guards of 8mm thikness with tempered prismed glass diffuser and stainless steel screws with Silicon Gaskets and high corrosion resistant Paint of Artlite make RL4009 IP65 Light Fixture with 35 watt HIT-TC lamp with integral control gear with concrete base for 4 beams equivalent to Artlite make RL4133 / RL 4134

no no no

50.0 20.0 15.0

7.4

no

40.0

7.5

no

10.0

Signature and stamp of Bidder

Sabarmati River Front Development Corporation Limited

Electrical Work BOQ : 20 of 27

SR. NO. 7.6

DESCRIPTION IP65 wall mounted UP & Down Lighter with 70 watt CDMT integral Light fixture made from die cast aluminium with anti glare baffles with one piece high purity reflector & durable silicon rubber, Clear toughned glass and corossion restant paint of Philips make Cat. no. DCP 721 / CDMT 70 watt IP65 wall mounted Down Lighter with 70 watt CDM-T integral Light fixture made from die cast aluminium with anti glare baffles with one piece high purity reflector & durable silicon rubber, Clear toughned glass and corossion restant paint of Philips make Cat. no. DCP 731 / CDMT 70 watt IP 65 Post top Lanetrn Fitting with 150 watt Master Colour CDM-T with Integral Electronic control Gear with presmatic diffuser with louvers with Optical cover Transparent polycarbonate bowl and cover with high pressure die cast alluminium housing with extruded alluminium disc supported roads with polymethylmethacrylicimide refractor & diffusers with acrylonitrilbutadienestyrene horizontal reflective disk of Philips make Malmo CDS 550 / 150 watt CDM-T Decorative Indirect post top luminaire IP 65 Post top lantern fitting Suitable for CDM-T 150W Master Colour CDM-T with Integral Electronic control Gear with housing made from die cast alluminium with high finish extruded aluminium column of 4 mtr with base flange.extruded aluminium pole also provided along with post top Corrosion resistant powder paint with chemical protection Remote integral control gear of Philips make Regina CPP 735 - 1 x 150 watt CDM-T lamp with pole 1) 8 way connector and 6A MCB 2) 50 mm diameter DWC pipe for each cable entry. Pipe length is up to 3.5 mtr. Per cable 3) Wiring up to the light fixture from the junction box using 3nos x 1.5 sq.mm. flexible copper wires / Fixture of specified make. 4) 1 mtr deep M 20 grade Concrete coping with base plate with stiffner with anchor bolts.

UNIT no

QTY 10.0

RATE SUPPLY ITC TOTAL

TOTAL RATE IN WORDS

AMOUNT

7.7

no

70.0

7.8

no

200.0

7.9

no

40.0

Signature and stamp of Bidder

Sabarmati River Front Development Corporation Limited

Electrical Work BOQ : 21 of 27

SR. NO.

DESCRIPTION 5) Sprial/Coil Type Earthing from the 8 swg Cu. Wire of 2.5 mtr. With the suitable size pipe with clamps and painting. 6) Radium stip of two colour at suitable height 7) Excavation & back filling for erection of poles. Debris to be removed from the site to suitable location as per the instruction of the engineer incharge

UNIT

QTY

RATE SUPPLY ITC TOTAL

TOTAL RATE IN WORDS

AMOUNT

7.10 IP 65 Light Column of 14 feet height with 4 feet light section made of Clear acrylic, elliptical lens with a satin finish and internal flute. Mechanically assembled to the housing & 10 feet of pole shaft made of Made from 7" (178 mm) wide by 5" (127 mm) deep, elliptical, extruded (6061-T6) aluminum tubing, having a 0.250" (6.4 mm) wall thickness, welded to both the bottom and top of the anchor plate with 70 watt CDM - R Lamp with ballast of High power factor of 90% with Lamp starting capacity of 20F (-30C). Assembled on a unitized removable tray withquick disconnect plug with Housing made from an elliptical die cast (356) aluminum frame of 7" (178 mm) wide by 5" (127 mm) deep having a 0.188" (4.7 mm) equivalent to Philips ( Lumec ) make Light Column OV 2

no

10.0

1) 8 way connector and 6A MCB 2) 50 mm diameter DWC pipe for each cable entry. Pipe length is up to 3.5 mtr. Per cable 3) Wiring up to the light fixture from the junction box using 3nos x 1.5 sq.mm. flexible copper wires / Fixture of specified make. 4) 1 mtr deep M 20 grade Concrete coping with base plate with stiffner with anchor bolts. 5) Sprial/Coil Type Earthing from the 8 swg Cu. Wire of 2.5 mtr. With the suitable size pipe with clamps and painting. 6) Radium stip of two colour at suitable height 7) Excavation & back filling for erection of poles. Debris to be removed from the site to suitable location as per the instruction of the engineer incharge

Signature and stamp of Bidder

Sabarmati River Front Development Corporation Limited

Electrical Work BOQ : 22 of 27

SR. NO.

DESCRIPTION

UNIT no

QTY 5.0

RATE SUPPLY ITC TOTAL

TOTAL RATE IN WORDS

AMOUNT

7.11 Supply, installation, testing and commisioning of Decorative lantern IP 66-Top cover is made of die cast aluminium,plug cover made of die cast aluminium with two captive screws fitted with a reflector anodised aluminium,upper reflector made up of chemically polished spun aluminium attached to the cover of the luminaire., Lower reflector made of chemically polished spun aluminium.Base and arms made up of die cast aluminium,protector made up of injection moulded polycarbonate having impact resistance of IK O8.The luminaire is suitable for 150 watt MH or CDMT lamp.Integral fixtures with lamp and control gear & complete to be fixed on the street light poles should be of top mounting type with toughened glass complete in all respect equivalent to Schreder make ALURA/STRIATED METHACRYLATE/1577/CDM-T/150

7.12 Supply, installation, testing and commisioning of IP-66 luminaire consisting of two parts made of painted, die cast Aluminium alloy. The body contains a reflector made of polished and anodised Aluminium and a removable control gear plate. The protector is made of hardened glass having impact resistance of glass IK 08. It is sealed to the cover with a silicone gasket. It is suitable for 250W HPSV Lamp . complete in all respect with the Control Gear, Lamp & other Accessories integral type equivalent to Schreder make NEOS 3 / IB / 250/ 1709. with Son T + PIA / MH lamp

no

5.0

7.13 IP65 flood light luminaire with integral control gear with 250 watt Metal Helide lamps & Control gear of Philips make MWF 331 / 250 watt SK / AK

no

90.0

Signature and stamp of Bidder

Sabarmati River Front Development Corporation Limited

Electrical Work BOQ : 23 of 27

SR. NO.

DESCRIPTION

UNIT no

QTY 2.0

RATE SUPPLY ITC TOTAL

TOTAL RATE IN WORDS

AMOUNT

7.14 SITC of Kesselec Schreder make : Cat. Ref. N. Trapez Pole ( 9 mtr. G. I. ) with 4 arm Bracket with 4 nos. of PQ3S fitting : comprising of 9 mtr. Pole with 4 arm. Bracket pole with 4 nos. of fitting with 140 watt Cosmo polis Lamp & control gear complete in all respect from specified approved make Luminaries shall be IP66 SEAL SAFE, comprised of an aluminium body and thermally tempered glass protector. The optical compartment is comprised of a deep drawn, polished and anodised reflector. The luminaries is with 8 mt decorative pole & Four arm bracket of 1000 mm on each side & have provision for the bunting. The pole & brackets are painted with MRF PU paint .Luminaries is suitable for cosmopolis lamp of 150 watt with lamp.

1) 8 way connector and 6A MCB 2) 50 mm diameter GI pipe for each cable entry. Pipe length is up to 3.5 mtr. Per cable 3) Wiring up to the light fixture from the junction box using 3nos x 1.5 sq.mm. flexible copper wires / Fixture of specified make. 4) Concrete coping of 1.5 mtr. with 1 mtr. Long foundation bolt with base plate with stiffener as per drawing. 5) Spiral/Coil Type Earthing Wire of 2.5 mtr. With the suitable size pipe with clamps and painting. 6) Radium strip of two color at suitable height 7) Excavation & back filling for erection of poles. Debris to be removed from the site to suitable location as per the instruction of the engineer in charge 7.15 SITC of Kesselec Schreder make Cat. No. FTR 390 / 1 x 55 watt T5- R lamp with lamp control gear ^ all hanging accessories no 12.0

Signature and stamp of Bidder

Sabarmati River Front Development Corporation Limited

Electrical Work BOQ : 24 of 27

SR. NO.

DESCRIPTION

UNIT

QTY

RATE SUPPLY ITC TOTAL

TOTAL RATE IN WORDS

AMOUNT

7.16 Supplying, erecting, connecting, testing and commissioning of following type Street Light Fixture with all necessary Hadware, Internal Wiring with Lamp, Ballast etc. all required accessories Complete in all respect. 7.16.1 Any kind of Light Fixtures type - A (with Basic Rate of Rs.8000/-) 7.16.2 Any kind of Light Fixtures type - B ( with Basic Rate of Rs.15000/-) 7.16.3 Any kind of Light Fixtures type - C ( with Basic Rate of Rs.30000/-) 7.16.4 Any kind of Light Fixtures type - D ( with Basic Rate of Rs.50000/-) 7.16.5 Any kind of Light Fixtures type - E ( with Basic Rate of Rs.100000/-) 7.16.6 Any kind of Light Fixtures type - F ( with Basic Rate of Rs.200000/-) 7.17 Supply, installation, testing and commissioning of Fans ( Energy saving ) without fan regulator. 7.17.1 36" dia sweep high speed high breeze ceiling fans white in colour. 7.17.2 48" dia sweep high speed high breeze ceiling fans white in colour. 7.17.3 Additional fan rod made out of 10 guage painted GI pipe with all required accessories for fan suspention. 7.18 Exhaust Fans : 7.18.1 SITC of light duty 225 mm. diameter propeller exhaust fans with louvers Sub Total 7..... no 20.0 no no no no no no 250.0 100.0 75.0 10.0 10.0 5.0

no no rmt

5.0 45.0 10.0

Signature and stamp of Bidder

Sabarmati River Front Development Corporation Limited

Electrical Work BOQ : 25 of 27

SR. NO. 8.0 8.1

DESCRIPTION Earthing Supplying & erecting funnel type earthing having earth plate of following size buried in specifically prepared earth pit 3 mtr. below ground with 40 kg. charcoal and salt with alternate layers of charcoal & salt, 20mm.dia. G.I. pipe with Funnel with a wire mesh for watering & bricks masonry block, C.I. Cover complete as per para 7.3 of IS 3043 with necessary length of double G.I. / copper earth Strip of the 25 x 3 mm bolted with Brass Screw to the plate 3 mtr long complete connected to the nearest switch gear with end socket as per direction & duly tested by earth tester confirming to ISS (As per drawing) with following specification, with Excavation, Back Filling, Making the Chamber & Chamber cover complete in all respect.

UNIT

QTY

RATE SUPPLY ITC TOTAL

TOTAL RATE IN WORDS

AMOUNT

8.2

Chemical Type Earthing ( Ashlok or equivalent ) Supplying & erecting in earth pit of minimum bore dia. 225mm size , approved make Safe Earthing Electrode consisting Pipe-in-Pipe Technology as per IS 3043-1987 made of corrosion free G.I.Pipes having Outer pipe dia of 50mm having 80-200 Micron galvanising, Inner pipe dia of 40 mm having 200-250 Micron galvanising, connection terminal dia of 14 mm with constant ohmic value surrounded by highly conductive compound with high charge dissipation suitable for following type of applications. (a) For Electrical installation up to 11 KV located in other than normal soil i.e. Soft Rock, Marshy Soil etc. -Length of Pipe : 2000 mm -Back filling Compound :1 no. Bag of 25 Kg.

no

15.0

Signature and stamp of Bidder

Sabarmati River Front Development Corporation Limited

Electrical Work BOQ : 26 of 27

SR. NO. 8.3 Earth wire/strips :

DESCRIPTION

UNIT

QTY

RATE SUPPLY ITC TOTAL

TOTAL RATE IN WORDS

AMOUNT

Supply and laying required size Cu/GI. earthing strips for interconnecting the earthing stations, panels, section pillar etc. in built up trenches, on walls/ceiling, buried in ground generally as specified and shown on drawings complete with : a) Fixing accessories. b) Corrosion protection of buried conductors with bituminous coating and covered with PVC tapes. 25 x 3 mm cu. strip 25 x 3 mm GI. strip No.8 gauge bare cu. earth wire No.16 gauge bare GI. earth wire Sub Total 8..... P. A. System SITC of DVD player of Philips make DVP 3336/94 SITC of IP 65 wall mounting / Pole Mounting speaker with 5W rated input power 3.3 K. Ohms / 3W impedance, 100 10000 Hz frequency response with 6 inch dia. cone type 8 ohms speakers duly fitted in ABS plastic cabinet of color match with wall or ceiling of following size and as directed by engineer in charge (Philips / Bosch make)

8.3.1 8.3.2 8.3.3 8.3.4 9.0 9.1 9.2

mtr mtr mtr mtr

100.0 1,000.0 600.0 20,000.0

no no

1.0 200.0

9.3 9.4

SITC OF microphone with press to call switch for Public address system, (Philips / Bosch make) SITC of local volume control -cum ON-OFF switch with flush mounting metal boxes, mounting plate matching with electrical switches (Same make as switch) Supplying & Laying of 2 Core X 1sq.mm Shielded wire in PVC Pipe With all accessories. ( For Speaker wiring)

no no

5.0 5.0

9.5

mtr

6,000.0

Signature and stamp of Bidder

Sabarmati River Front Development Corporation Limited

Electrical Work BOQ : 27 of 27

SR. NO. 9.6

DESCRIPTION

UNIT no

QTY 1.0

RATE SUPPLY ITC TOTAL

TOTAL RATE IN WORDS

AMOUNT

SITC of power Audio amplifiers including all necessary control desk and microprocessor based control unit with microphone, BGM, Call Station & PC input including providing necessary rack for mounting the Amplifier (with Rack ). Suitable to connect 200 Speakers (Philips / Bosch / Ahuja make)
SITC of 4 zone Switcher

9.7

no

1.0

Sub Total 9.....


10.0 Miscellaneous 10.1 Liason / Follow UP with Supply Co. Filling the necessary application to supply co. following up and getting the supply filling the necessary test report to the supply co. inclusive. All official fees including security deposits will be paid by the client and out of pocket expenses shall be of contractor. 10.1.1 10.1.2 10.1.3 10.2 up to 10 KW FOR 10 to 20 KW More than 20 KW Providing , erecting , fabricating the M.S. structure as per requirement on site incorporating proper size of M.S. angles, flats, bars, channels, pipes, sections, Sheets & for the pole swaging with the suitable dia pipe complete with cutting, welding, grinding & finishing duly painted with two coat of red oxide & 1 coat of P.U. Paint with erection on site as per direction of engineer in charge with necessary grouting, cementing, plastering & finishing complete as per the instruction of the engineer in charge. No No No Kg 5.0 5.0 10.0 3,000.0

Sub Total 10.....

Signature and stamp of Bidder

Вам также может понравиться