Академический Документы
Профессиональный Документы
Культура Документы
CC62P
DE 240309
Specially designed for SIEMENS CC62P toxic and explosive gas detection system. Electrochemical sensor provided of a filter for SOx, NOx y H2S. Calibrated at factory with target gas.
Application
Carbon Monoxide (CO) is a poisonous, odourless and colourless gas produced by the incomplete combustion of fossil fuels (petrol, butane, propane, natural gas, kerosene, carbon and wood). It is very dangerous when inhaled, even in small quantities. It inhibits the blood capacity to carry oxygen and can cause death in a few seconds. Some of the CO emission sources are fuel burners in a bad condition or wrongly installed, water heaters, chimneys, petrol vehicles, etc CO detection in underground cark parks The detector has been specially designed for underground cark parks, road tunnels, garages and, in general, for those installations where there is presence of carbon monoxide.
Recommendations
Do not install the detectors unless the construction and painting works are finalised. Avoid connecting the detectors close to sources that generate electromagnetic disturbances (fluorescents lights, motors, counters, etc.) or use shield cable. Do not paint nor drill holes on the detector housing. We recommend not storing the detector for more than six months.
Technical characteristics
Detector SIEMENS for carbon monoxide (RS485) Technology Voltage Consumption Measurement range Resolution Reproductiveness Linearity Calibration gas Sensor life expectancy Relative humidity Atmospheric pressure Working temperature Time response Cable entry Communication Protection grade Presentation Weight (gr) & Dimensions (mm) Height of installation Cover 8 bits microprocessor and electrochemical sensor with filter for SOx/NOx/H2S From 9V to 15V DC 8mA (stand-by) 15mA (alarm). From 0 to 400 ppm 2 ppm 1% bottom of scale Linear in all the scale Precise mixture 200 ppm CO + N2 150 ml / min 4 years in normal working conditions From 15% to 90% (continuous) & from 0% to 99% (intermittent). 10%. From 15C to +50C T90 < 40 s. PG9 stopping plug IP67 self-blocking RS485 addressable (1 to 16). IP65 ABS & Makrolon 325 grs. 120-150-63 (including sensor head & cable entry) 1,8 - 2 m from floor 200 m2 (according with current standard).
Other available gases in this format: NO2, NO, O2, HCl, Cl2, SO2, H2S, Exp
Alarm output Fault output Battery output Power supply Mains entrance Dimensions -mmWeight -kg-
DATASHEET DTRNO2
CC62P
DE 240309
NO2
Specially designed for SIEMENS CC62P toxic and explosive gas detection system. Designed for detection of Nitrogen Dioxide in closed areas.
Features & Characteristics Maximum features Last generation of electrochemical sensor The recommended coverage area is 200m2
Coverage area
Height of installation
Maintenance
It is recommended to check the status of the detectors every year and adjust those detectors that require it. The life expectancy of the sensor is 2 years -following manufacturer indications-. After this time, the sensor should be replaced if necessary.
Recommendations
Do not install the detectors unless the construction and painting works are finalized. Avoid connecting the detectors close to sources that generate electromagnetic disturbances (fluorescents lights, motors, counters, etc.) or use shield cable. Do not paint nor drill holes on the detector housing. We recommend not storing the detector for more than six months.
Other available gases in this format: CO, O2, NO, HCl, Cl2, SO2, H2S, Exp
Alarm output Fault output Battery output Power supply Mains entrance Dimensions -mmWeight -kg-
DATASHEET DTRO2
CC62P
DE 240309
Specially designed for SIEMENS CC62P toxic and explosive gas detection system. Designed for detection of lack of Oxygen in closed areas.
Application SIEMENS CC62P detectors for Oxygen using electrochemical technology have been designed for closed areas. The excess or lack of Oxygen in air can cause in the human being from euphoria to death. Their main applications are: cellars, food processing, grain storage, greenhouse, incubators, mining, nuclear industry, oil rings and sewage industry. The lack of Oxygen at work places may cause anoxy symptoms.
The ventilation level has been programmed to act when the Oxygen level goes down 15%, otherwise the alarm level will act when the Oxygen level goes up 24%. Both levels, ventilation & alarm, are totally programmable from the Control Unit SIEMENS CC62P. The recommended coverage area is 100m2
Coverage area
Height of installation
The recommended height of installation is 1,7 to 2 meters from floor established following the average height of the human being.
Maintenance
It is recommended to check the status of the detectors every year and adjust those detectors that require it. The life expectancy of the sensor is 2 years -following manufacturer indications-. After this time, the sensor should be replaced if necessary.
Recommendations
Do not install the detectors unless the construction and painting works are finalized. Avoid connecting the detectors close to sources that generate electromagnetic disturbances (fluorescents lights, motors, counters, etc.) or use shield cable. Do not paint nor drill holes on the detector housing. We recommend not storing the detector for more than three months.
Other available gases in this format: NO2, NO, CO, HCl, Cl2, SO2, H2S, Exp
Alarm output Fault output Battery output Power supply Mains entrance Dimensions -mmWeight -kg-
CONTROL UNITS Code SICT1**** SICT2**** SICT3**** SICT4**** SIMZ**** Description Control Unit 16 detectors Control Unit 32 detectors Control Unit 48 detectors Control Unit 64 detectors Module line
**** Add at the end of the code the five letters corresponding to the selected Keypad/Standard Ex: For German Standard / English Keypad, code would be SICT1IANAI
Code EENEI EESEI EPNEI EPSEI IPNIP IPSIP EPNPI EPSPI IANAI IENIE
Standard / Keypad Languages Spanish Standard / Spanish Keypad no integration Spanish and English languages Spanish Standard / Spanish Keypad with integration Spanish and English languages Port-International Standard / Spanish Keypad no integration Spanish and English languages Port-International Standard / Spanish Keypad w/ integration Spanish and English languages Port-International Standard / English Keypad no integration English and Portuguese languages Port-International Standard / English Keypad w/ integration English and Portuguese languages Port-International Standard / Spanish Keypad no integration English and Portuguese languages Port-International Standard / Spanish Keypad w/ integration English and Portuguese languages German Standard / English Keypad German Standard cannot be integrated English and Portuguese languages Spanish Standard / English Keypad no integration English and Spanish languages