Академический Документы
Профессиональный Документы
Культура Документы
21
Cementing 1
22
Cementing 1
Introduction
For well operations to take place, lengths of tubular goods are joined together and run downhole. Then, surface and downhole equipment can be connected so that drilling and cementing operations can proceed. Due to the nature of our work, Halliburton personnel must be familiar with basic drilling operations. An understanding of the factors involved in making up joints of casing, tubing, and drill pipe will help you work more effectively with customers as well as better understand the ways in which Halliburton equipment is used with these tubular goods.
Topic Areas
This section presents the following topics: A. Casing and Tubing Uses B. Couplings and Threads C. Casing and Tubing Threads
Learning Objectives
Upon completion of this section, you should be familiar with the Purpose and use of tubular goods Types of threads and how to select and care for them
23
Cementing 1
Troublesome zones (such as salt) and sloughing shale Lost circulation zones
on the casing also has an effect upon the collapse and burst values. You may also encounter compression and bending forces, which often occur in nonvertical holes. The degree to which these forces are exerted will also effect the burst and collapse resistance of the pipe. Another secondary condition is load change during cementing due to the placement of fluids of differing densities. API bulletins, as well as the Redbook, contain minimum burst, collapse, and tension casing values. To use APIs monogram, casing manufactures must use minimum standards set by the API. Non-API casing is often manufactured using the same standards, but for critical wells, be sure that the material meets all API standards.
Remember, the casing size and weight chosen will determine casing inside diameter (ID). This, in turn affects maximum bit diameter and limits the size of the next casing string. The basic loading conditions on a casing or tubing string that must be considered are collapse, burst, and tension. All pipe designs must carry a safety factor that considers the uncertainty of the magnitude of these forces. The Red Book (Halliburton Cementing Tables) lists collapse and burst (internal yield) limitations for common pipe sizes and grades. In addition, the Redbook provides limitations on the tensile force (parallel to the axis of the casing string) that is allowed for different pipe sizes, grades, and coupling types. Tensile force
Unit A Quiz
Fill in the blanks with one or more words to check your progress in Unit A. 1. The casing program should be appropriate for the __________________________ and allow safe well production. 2. The casing size and weight chosen will determine casing ________________________. 3. The basic loading conditions on a casing or tubing string that must be considered are ______________, ________________, and _______________.
24
Cementing 1
Conductor Casing
Conductor Casing
Surface Casing
The surface casing string (Fig. 2.2) is designed to protect formations near the surface from deeper drilling conditions. The surface casing string has several important functions. First, it protects shallow freshwater sands from contamination by drilling fluids and produced fluids. Surface casing is cemented back to the surface so freshwater zones will have a cement sheath and a steel casing to protect them. Depth and cement requirements are mandated by regulatory agencies. Surface casing allows you to drill to the next casing seat. BOPs are nippled up on the surface casing; the well can be controlled if abnormal conditions cause an inflow of formation fluid to the wellbore. The surface casing is designed so that the casing can be totally shut in using surface equipment. When drilling into abnormal pressure, casing seats must be able to withstand increasing mud weights. Casing should be set deep enough to prevent broaching to the surface. Finally, surface casing supports all casing strings run in the well.
Reservoir
Figure 2.1 - Conductor Casing The conductor casing prevents washouts of poorly consolidated surface soil and rock while drilling the surface hole. Should the surface erode, or become unstable, drilling rig stability is compromised. Conductor casing normally has a large diameter (16 to 30 in.). It is either set with a spud rig or driven to the point of refusal (150 to 250 blows/ft) with a drive or vibration hammer. Setting depths is normally 90 to 150 ft and rarely deeper that 300 ft. Conductor casing allows you to install a diverter system, and provides a flow line high enough to allow mud return to steel mud pits while drilling the surface hole. A blowout preventer (BOP) may sit on the conductor casing above a largediameter ( 10 in.) vent pipe. If shallow hydrocarbons are found, and the well flows, you can close the BOP and divert flow away from
25
Cementing 1
Intermediate Casing
Cement
Reservoir
Reservoir
Figure 2.3 - Protective Casing (Set inside the surface casing and extending from total depth to surface) One major advantage of protective casing is that it allows underbalanced drilling of deeper formations and isolates troublesome ones. It allows you to isolate sloughing shales, abnormally pressured saltwater flows, and formations that contaminate the mud to prevent interference during drilling operations
Production Casing
The production casing string (oil string) (Fig. 2.4) is set and cemented through the producing zone and acts as a backup for the tubing string during production. It is the primary string responsible for isolating the desired production interval(s). This string must be able to withstand full wellhead shut-in pressure if the tubing leaks or fails. After cementing the production casing, holes (perforations) are made in the casing (and cement sheath) which allows fluid to enter the wellbore. This is most often accomplished using explosive charges ran on wireline units provided by the logging service line. When replacing the tubing or downhole tools during well maintenance operations, you must make sure the production casing will allow you
26
Cementing 1
to kill the well (offset bottom hole pressure with fluid hydrostatic head), circulate workover fluids, and conduct some pressure testing. Casing in general and production casing/liners specifically, allow for a wellbore with consistent known internal diameter. This is critical when utilizing special downhole tools that require these conditions. These tools are commonly inserted into the casing during completion and production operations in order to obtain wellbore isolation at desired points. In some areas, conditions may allow you to use small diameter lines; in these instances, production casing is set for well fluid production. In other words, these are tubingless completions there is no backup string.
cemented casing string. These hanging casing strings are called liners and they are used in almost every deep well completion. Four types of liners will be described briefly to begin this section: Drilling (or protective) liners Production liners Stub liners Scab liners
Drilling Liners
A drilling liner (Fig. 2.5) is a string of casing that is hung from another casing of a larger diameter which has already been cemented downhole. It is used to case off open holes so that deeper drilling may be performed. A drilling liner serves to help control water or gas production isolate lost-circulation zones isolate high-pressure zones.
Intermediate Casing
Cement
Production Casing
A drilling liner is subject to the same design conditions as protective casing, and it provides the same protections. Multiple drilling liners may be required. As with all liners, the top of the casing does not extend to the surface, but is hung off at some point in the previous casing string.
Figure 2.4 - Production casing (Last full string of casing, set from total depth to surface).
Liners
In the past, it was common to have several strings of casing in a deep well. All these strings extended from the wellhead to different depths. However, another method was devised to accommodate varying well conditions. This time- and money-saving method involves the hanging of a casing string from the bottom of a Figure 2.5 - Protective or Drilling liner (Set inside protective casing at current hole total depth, but does not extend to surface)
27
Cementing 1
Production Liners
A production liner is a string of casing that is hung from a drilling liner or casing in the producing formation (Fig. 2.6). This type of liner is then cemented and perforated like any other completion string. It provides isolation and support when casing has been set above the production zone.
Scab Liners
An unusual type of liner, a scab liner (Fig. 2.7) is usually not cemented after it has been run downhole and, therefore, it is retrievable. It has a packoff on both ends and is used under the same conditions as a stub liner. Stub and scab liners can be set with part of their weight on the liner below or hung uphole on existing casing.
Figure 2.6 Production liner (cemented in place but hangs from the bottom of the intermediate casing rather than extending to the surface.
Stub Liners
A stub liner (also called a tie-back liner) is usually a short string of casing that provides an upward extension for a drilling liner. It is run when casing above the drilling liner has been damaged in some way (by corrosion, etc.) a liner is leaking greater resistance is needed for other reasons (abnormal pressure, etc.).
Tubing String
The tubing string gives produced fluids a flow path to the surface and allows you to inject for secondary recovery, storage, and disposal. By increasing the size of this string, you can reduce friction pressure and increase production or injection rates. However, by increasing this diameter, you must increase all other casing sizes in the well. In other words, you must make sure the increased production/injection ratio justifies the higher cost.
28
Cementing 1
Unit B Quiz
Fill in the blanks with one or more words to check your progress in Unit B. 1. The first string in the well may be ___________ or ___________ casing. If the top soil is erodible, then ___________ casing will be the first type run. 2. The conductor prevents ______________ under the rig. 3. Sometimes, conductor casing is set by simply _________________________ it into the ground. However, if the soil is too hard, then the hole will be _____________ for it. 4. ____________ casing supports all casing strings run in the well. 5. Protective casing is also know as _____________________ casing. 6. A hanging casing string is called a ____________.
29
Cementing 1
Casing Threads
Casing threads appear on both ends on the outside of a joint of casing. Lengths of casing are made up by using a collar (Fig. 2.9). A joint screws into one end of the collar, while the next joint screws into the other end. Most casing threads are not upset, that is flared, as are many tubing threads.
Figure 2.9 Casing Joints and Collar The most common threads (Fig. 2.10) in use today for casing connections are: Figure 2.8 Pin End and Box End Since 1928, threads have been regulated by the American Petroleum Institute (API). There are five important areas of thread types, selection, and care. Casing Threads Tubing Threads Thread Selection 8 round (8rd) thread has 8 rounded threads per inch Extreme line (Xline) thread has square threads* Buttress thread has square threads.
2 10
Cementing 1
* Number of threads per inch varies based upon the OD of the pipe.
Tubing Threads
The tubing or production string provides a flow path to the surface for produced fluids. Tubing is not cemented into place as is casing. Therefore, the threads on tubing joints and collars (Figure 2.11) are designed to withstand great tensile loads and internal pressures. Like casing joints, tubing has threads on both ends. Two types of tubing threads (Figure 2.12) are External Upset (EU) used in most wells for added strength Non-Upset used in shallower wells and on the surface.
2 11
Cementing 1
Thread Selection
When working with the customer's casing, tubing or drill pipe, its up to Halliburton personnel to be sure that service equipment fits the tubulars. Selection of the proper pin size (changeover from the casing/tubing to Halliburton discharge piping) can sometimes be difficult for the beginner. In selecting the proper pin for casing, tubing or drill pipe, the following information is needed: What type of thread is on the string? What is the outside diameter (OD) of the pipe on the string? (For drill pipe you would need to know the OD of the tool joint or coupling). Figure 2.13- Caliper and ruler
The type of thread varies depending upon which type of pipe the customer has in the hole. The OD tells you what size pin you need to connect to the customers pipe. For example, if you know the customer has 5 inch 8rd casing, your equipment should also have an OD of 5 inches and 8 round threads per inch. On location, check the specifications, which are stenciled on the side of the joints. If the joints are not marked, youll need a caliper tool (Fig. 2.13) and ruler to identify pin dimensions.
2 12
Cementing 1
Nominal Weight, Threads and Coupling lb per ft 14.00 14.00 15.50 17.00 14.00 15.50 17.00
Grade H-40 J-55 J-55 J-55 K-55 K-55 K-55 H-40 J-55 J-55 K-55 K-55
Optimum 1300 1720 2020 2290 1890 2220 2520 1840 2450 3140 2670 3420
Minimum 980 1290 1520 1720 1420 1670 1890 1380 1840 2360 2000 2570
Maximum 1630 2150 2530 2860 2360 2780 3150 __ 3060 3930 3340 4280
6 5/8
Using this information, you can look up the optimum, minimum, and maximum torque to be applied when making connections with this casing. To do this, find the chart for casing and your thread size. The first column of this chart is labeled Size:Outside Diameter. Find the column for 5 in. OD casing. Columns 2 and 3 are labeled Nominal Weight, Threads and Coupling lb per ft and Grade. Find the row for the casing youre working with (15.5 lb/ft and Grade J-55). Columns 7, 8 and 9 are labeled Long Thread, and Optimum, Minimum, and Maximum torque levels. For the casing youre working with, these levels are 2170, 1630, 2710 ft-lb, respectively. Thus, proper torque for this casing is between 1630 and 2710 ft-lb, and 2170 ft-lb is the best torque to apply.
Thread Care
When working with both surfaces and downhole equipment, you should be careful to protect the threads. Because of the tremendous pressure this equipment is designed to withstand, taking care of thread could mean the prevention of a serious accident and injury. Before taking a piece of equipment to location, you should Carefully remove the thread protectors. Inspect the threads for damage (sometimes diesel fuel or a solvent will be needed to remove grease to inspect for damage). Look for galling, cracking, or cross-threading. If youre not sure, check with your supervisor. Put on safety glasses and clean the threads using a wire brush. If the threads will be chemically welded (with Halliburton Weld-A), bentonite gel will be needed along with a wire brush to remove all grease from the threads on the equipment as well as on the casing. Check to see that all welds have met established API codes.
2 13
Cementing 1
After a piece of equipment has been inspected, equal care should be taken in its use: Never allow threads to hit metal or hard objects. Never drop or throw equipment. Be aware of proper torque when making up a piece of equipment. Place wrenches close to the threads but not on them.
After youve finished using the equipment, reinspect it for damage. Be sure to clean the thread protectors and carefully reattach them to the equipment. Remember, if you have a question about the condition of a thread, ask a supervisor. One blown out pin could not only cause an accident, but could also leave you with a workstring full of cement.
Unit C Quiz
Fill in the blanks with one or more words to check your progress in Unit C. 1. Threads have been regulated by the _______________ for over 50 years. 2. As a connection is screwed together, the pin threads begin to ______________ to the box threads. Eventually, the pin end is ________ tightly into the box, which produces a __________ against internal pressure. 3. Both the ____________ and____________ types of casing threads are square-shaped. 4. The two main questions you need to answer when choosing the proper pin size for casing or tubing are: What is the type of ______________ on the string, and what is the ______________ of the pipe on the string? 5. When inspecting threads, you should look for _________________, __________________, and ___________________.
2 14
Cementing 1
2 15
Cementing 1
2 16
Cementing 1