Академический Документы
Профессиональный Документы
Культура Документы
Contents
1. Commissioning Overview 2. Local Commissioning through the USB Disk
Page1
Introduction to Commissioning
To ensure that the eNodeB operates normally after the installation
Commissioning Modes:
M2000-based Commissioning USB+M2000-based Commissioning Local Commissioning with LMT
Commissioning Scenarios:
Without a Security Gateway With a Security Gateway
Commissioning Prerequisites:
eNodeB hardware installed and ready Transport Network ready (for Remote Commissioning with M2000)
Copyright 2013 Huawei Technologies Co., Ltd. All rights reserved. Page2
Page3
Page4
M2000 Server
Page5
M2000 Server
eNodeB
Page6
Contents
1. Commissioning Introduction 2. Local Commissioning through the USB Disk 3. Local Commissioning through the LMT
Page7
Page8
Page9
Page10
Page11
Page13
Page14
Page15
Page16
Page17
Page18
Step2 eNodeB will automatically upgrade the software and download the data configuration file, and restart. Then verify that the loaded software and data configuration files have taken effect. Step3 Remove the USB flash drive after loading succeeds.
Copyright 2013 Huawei Technologies Co., Ltd. All rights reserved. Page19
10
11
12
Page24
Page25
13
Page26
Remote operations
In M2000 do the procedures for commissioning, including: Performing OM channel setup confirmation Acquire an NE commissioning verification report Confirm that auto deployment tasks are completed Setting the maximum output power for RF modules Set an NE to the NORMAL mode
Page27
14
Page28
Contents
1. Commissioning Introduction 2. Local Commissioning through the USB Disk 3. Local Commissioning on the LMT
Page29
15
Remote operation
Local operation .
Compare the license file with the configuration data of eNodeB Set the eNodeB status End
Page30
Arrange for the tools required for the local commissioning on the LMT
Laptop Ethernet cable for connection to LMPT / UMPT Adapter for Local Maintenance for connection to UMPT
Page31
16
Default Local OM IP address: 192.168.0.49 Setting PC IP same segment, such as: 192.168.0.88
3. PC
Page32
1 4 3
1.UMPT
3. Ethernet cable
Page33
4. PC
17
Page34
18
Page36
Upgrade the eNodeB Software and Data Configuration File on the LMT
Page37
19
Software Storage
Page38
Software Rollback
Command:
RBK SOFTWARE
Notes: Before implement software rollback, we should check if there is any valid software for rollback, using the following command:
Page39
20
Page40
21
Page43
22
End
Page44
Page45
23
Page46
Page47
24
Page48
Page49
25
Page50
Page51
26
Page52
RET+STMA
RET+SBT
RET Only
Page53
27
RET+STMA
RET+SBT
RET Only
Page54
RET+STMA
RET+SBT
RET Only
Page55
28
Page56
Page57
29
Page58
Key MO to configure
ADD ETHPORT ADD VLANMAP SET DSCPMAP ADD VLANCLASS End Point ADD DEVIP ADD IPRT ADD SCTPTEMPLATE ADD SCTPHOST ADD SCTPPEER ADD USERPLANEHOST ADD USERPLANEPEER ADD EPGROUP ADD SCTPHOST2EPGROUP ADD SCTPPEER2EPGROUP ADD UPHOST2EPGROUP ADD UPPEER2EPGROUP ADD S1 ADD X2 Link ADD DEVIP ADD IPRT ADD SCTPLNK ADD CPBEARER ADD S1INTERFACE ADD X2INTERFACE ADD IPPATH(S1&X2) ADD ENODEBPATH
Transmission Security
ACL ACLRULE IKEPROPOSAL IKEPEER IPSECPROPOSAL IPSECPOLICY PSECBIND PACKETFILTER
Digital
CERTMK Certificate APPCERT TRUSTCE RT CROSSCE RT
Page59
ADD OMCH
30
Page60
Configure Sectors
Page61
31
Configure Cells
Page62
Page63
32
Summary
eNodeB commissioning Modes Commissioning Preparations The procedure of local commissioning through the USB Disk The procedure of local commissioning through the LMT The procedure of local commissioning through LMT with MML commands.
Page64
Thank you
www.huawei.com
33