Вы находитесь на странице: 1из 31

Parts and Accessories

Installation Instructions

039 0411 Z

Rear-View Camera Retrofit


BMW 3 Series Coup (E 46/2)
BMW 3 Series Saloon (E 46/4)
These installation instructions are only valid for cars with SA 609 (navigation system).
The installation time for cars with TV function is approx. 2.5 3.0 hours, for cars without TV function it is
approx. 3.5 4.0 hours. The installation time for E46/2 cars built from 03/03 onwards is approx. 0.5 hours
longer. The installation time may vary depending on condition of the car and the equipment in it.
Retrofit kit No.:

84 21 0 150 717
84 21 0 300 908
84 21 0 301 007

Retrofit kit No.: 84 21 0 150 717


Installation Instructions No.: 01 29 0 300 363

Issue date: 04.2003

Contents
Section

Page

Important information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1.

Preparations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.

Parts list for rear-view camera (cars with TV function only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3.

Parts list for rear-view camera and switchbox (cars without TV function only) . . . . . . . . . . . . . . . . .

4.

Connection diagram (cars with TV function only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5.

Connection diagram (cars without TV function only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6.

Installation and cabling diagram (cars with TV function only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

11

7.

Installation and cabling diagram (cars without TV function only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

12

8.

To install the rear-view camera and button (E46/2 up to 03/03 only) . . . . . . . . . . . . . . . . . . . . . . . .

13

9.

To install the rear-view camera and button (E46/2 from 03/03 only) . . . . . . . . . . . . . . . . . . . . . . . .

16

10. To install the rear-view camera and button (E46/4 only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

19

11. To install and connect the control unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

22

12. To install and connect the wiring harness (cars with TV function only) . . . . . . . . . . . . . . . . . . . . . . .

23

13. To install the switchbox (cars without TV function only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

24

14. To install and connect the wiring harnesses (cars without TV function only) . . . . . . . . . . . . . . . . . .

25

15. Concluding work . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

28

16. Circuit diagram (cars with TV function only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

29

17. Circuit diagram (cars without TV function only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

30

Retrofit kit No.: 84 21 0 150 717, other part numbers see cover sheet
Installation Instructions No.: 01 29 0 300 363
Issue date: 04.2003

EN/2

Important information
These installation instructions are primarily designed for use within the BMW dealership organisation and by
authorised BMW service companies.
In any event the target group for these installation instructions is specialist personnel trained on BMW cars
with the appropriate specialist knowledge.
Subject to technical modifications.
Do not archive the hard copy of these installation instructions since daily updates are made by Aftersales
Portal.
All work must be completed using the latest repair manuals, circuit diagrams, servicing manuals and work
instructions in a rational order using the prescribed tools (special tools) and observing current health and
safety regulations.
Ensure that the cables/lines are not kinked or damaged as you install them in the car. The costs incurred as
a result of this will not be reimbursed by the BMW Group.
Additional cables/lines that you install must be secured with cable ties.
If the specified PIN chambers are occupied, bridges, double crimps or twin-lead terminals must be used.
All the figures show LHD cars, proceed accordingly on RHD cars.
The switch-off delay (5 seconds) of the rear-view camera can be deactivated following consultation with the
customer.
Ordering instructions
Seal N of the grab handle (not fitted on E46/2 from 03/03 onwards) is not included in the retrofit kit and must
be ordered separately (see EPC for part number and documentation).
Pictograms
denotes instructions that draw your attention to special features.
denotes the end of the instruction or caution text.
Information on operation
The rear-view camera is only active when reverse gear is engaged and terminal 15 is active.
Required special tools
Unlocking hook (65 5 400)
Miniature drill with miniature cutting discs (E46/2 from 03/03 only)

Retrofit kit No.: 84 21 0 150 717, other part numbers see cover sheet
Installation Instructions No.: 01 29 0 300 363
Issue date: 04.2003

EN/3

1.

Preparations

Conduct a brief test


Disconnect the negative pole of the battery

TIS instruction No.


--12 00 ...

The following components must be removed first of all:


Trim for the boot lid

51 49 000

Grab handle (on boot lid)


Remove the boot lid grab handle seal

51 13 402
---

Boot floor trim

51 47 101

Left boot wheel arch trim

51 47 151

Release the navigation computer (cars without TV function only)

65 90 510

Right boot wheel arch trim

51 47 161
---

Rear closing panel trim

Retrofit kit No.: 84 21 0 150 717, other part numbers see cover sheet
Installation Instructions No.: 01 29 0 300 363
Issue date: 04.2003

EN/4

2.

Parts list for rear-view camera (cars with TV function only)

046 1346 Z

Legend
0

Wiring harness

Rear-view camera

Control unit

Mounting plate (not required)

Mounting plate

Philips screw 3.5 x 16 mm (6x)

Cable tie 292 x 4.8 mm

Cable tie 200 x 3.6 mm (20x)

Miniature connector (5x)

Protective strip

Button

Philips screw 3.5 x 8 mm (4x)

Cable tie holder (5x)

Grab handle seal (not supplied with retrofit kit)

Retrofit kit No.: 84 21 0 150 717, other part numbers see cover sheet
Installation Instructions No.: 01 29 0 300 363
Issue date: 04.2003

EN/5

3.

Parts list for rear-view camera and switchbox (cars without TV function only)

O
A

Q
A
A
R
A
S

A
T

U
A

A
V

W
A

046 1320 Z

Retrofit kit No.: 84 21 0 150 717, other part numbers see cover sheet
Installation Instructions No.: 01 29 0 300 363
Issue date: 04.2003

EN/6

3.

Parts list for rear-view camera and switchbox (cars without TV function only)

Legend
0

Wiring harness

Rear-view camera

Control unit

Mounting plate (not required)

Mounting plate

Philips screw 3.5 x 16 mm (6x)

Cable tie 292 x 4.8 mm

Cable tie 200 x 3.6 mm (30x)

Miniature connector (6x)

Protective strip

Button

Philips screw 3.5 x 8 mm (4x)

Cable tie holder (5x)

Grab handle seal (not supplied with retrofit kit)

Adapter cable

Power supply cable

Switchbox

Sealing strip (2x, not required)

Speed nut M5 (4x)

Hexagonal screw with washer M5 x 14 (4x)

Hexagonal nut with washer M5 (2x, not required)

Edge protector

Fillister head screw 4.2 x 13 mm (4x, not required)

Retrofit kit No.: 84 21 0 150 717, other part numbers see cover sheet
Installation Instructions No.: 01 29 0 300 363
Issue date: 04.2003

EN/7

4.

Connection diagram (cars with TV function only)

A3

A2

A4
A5

A
A1

A6
A7
A8
A9
046 1224 Z

Item

Description

Signal

Cable colour /
Cross-section

Wiring harness

---

---

A1

Black 12-pin socket casing

---

---

A2

Cable open

Connection location in the car

Abbreviation / Slot

---

---

To control unit C

---

0.75 mm2
A3

Cable open

RFS

RFS

To right reversing light,


X328
black 3-pin plug with miniature connector PIN 1
to blue/yellow cable

GN

Insulate and tie back

GN

---

0.75 mm2
A4

Socket contact

Video +

Transparent
0.14

A5

Socket contact

Video -

mm2

SW/BR
0.35 mm2

A6

Socket contact

RFS inv

SW
0.25 mm2

A7

Cable open

Terminal 30

RT
0.75 mm2

A8

Cable open

Terminal 31

BR
0.75 mm

A9

Socket contact

TA

WS
0.25 mm

Retrofit kit No.: 84 21 0 150 717, other part numbers see cover sheet
Installation Instructions No.: 01 29 0 300 363
Issue date: 04.2003

To video module A197,


natural colour 18-pin plug

X18806

To video module A197,


natural colour 18-pin plug

X18806

To video module A197,


blue 18-pin plug

X18804

PIN 14
PIN 17

To video module A197,


X18804
blue 18-pin plug with miniature connector PIN 1
to red/green cable
To video module A197,
X18804
blue 18-pin plug with miniature connector PIN 10
to brown cable
Insulate and tie back

PIN 13

---

EN/8

5.

Connection diagram (cars without TV function only)

A2

A3
A4
A5

A1

A6

O3
O4

O2

A7
A8
A9

P2
O5

P1

P3
P4

O1

046 1217 Z

Item

Description

Signal

Cable colour /
Cross-section

Wiring harness

---

---

A1

Black 12-pin socket casing

---

---

A2

Cable open

Connection location in the car

Abbreviation / Slot

---

---

To control unit C

---

0.75 mm2
A3

Cable open

RFS

RFS

To right reversing light,


X328
black 3-pin plug with miniature connector PIN 1
to blue/yellow cable

GN

Insulate and tie back

GN

---

0.75 mm2
Socket contact

Video +

To branch P1

PIN 24

To branch P1

PIN 11

To branch P1

PIN 23

To branch P3,
with miniature connector to red cable

PIN 25

To branch P4,
with miniature connector to brown cable

PIN 12

0.75 mm2

A4

WS

Insulate and tie back

Transparent
0.14

A5

Socket contact

Video -

mm2

SW/BR
0.35 mm2

A6

Socket contact

RFS inv

SW
0.25 mm2

A7

Cable open

Terminal 30

RT
0.75

A8
A9

Cable open
Socket contact

Terminal 31
TA

mm2

BR

0.25 mm2

Retrofit kit No.: 84 21 0 150 717, other part numbers see cover sheet
Installation Instructions No.: 01 29 0 300 363
Issue date: 04.2003

---

EN/9

5.

Connection diagram (cars without TV function only)

A2

A3
A4
A5

A1

A6

O3
O4

O2

A7
A8
A9

P2
O5

P1

P3
P4

O1

046 1217 Z

Item

Description

Signal

Cable colour /
Cross-section

Adapter cable

---

---

O1

Blue 18-pin socket casing

---

---

O2

Blue 18-pin plug casing

O3

Socket contact

Connection location in the car

--Terminal 30

---

Abbreviation / Slot

--To navigation computer A112

--X1313

To standard wiring harness

X1313

To branch P1

PIN 26

To branch P1

RT/GE

PIN 13

0.75 mm2
O4

Socket contact

Terminal 31

BR
0.75 mm2

O5

Natural colour 18-pin socket casing

---

---

Power supply cable

---

---

P1

Black 26-pin socket casing

---

---

P2

Cable open

To switchbox Q

Terminal R

VI/WS
0.50 mm

P3

Cable open

Terminal 30

RT
0.75 mm

P4

Cable open

Terminal 31

BR
0.75 mm2

Retrofit kit No.: 84 21 0 150 717, other part numbers see cover sheet
Installation Instructions No.: 01 29 0 300 363
Issue date: 04.2003

-----

---

To switchbox Q
To radio receiver N9,
with miniature connector to violet/white
cable

--X13646
PIN 16

To branch A7,
with miniature connector to red cable

---

To branch A8,
with miniature connector to brown cable

---

EN/10

6.

Installation and cabling diagram (cars with TV function only)

A
1

E65

2
046 1228 Z

Legend
1

Reversing light signal pick-up on the reversing light

Video module

Wiring harness

Rear-view camera

Control unit

Retrofit kit No.: 84 21 0 150 717, other part numbers see cover sheet
Installation Instructions No.: 01 29 0 300 363
Issue date: 04.2003

EN/11

7.

Installation and cabling diagram (cars without TV function only)

A
1

E65

B
2

3
046 1229 Z

Legend
1

Reversing light signal pick-up on the reversing light

Radio receiver

Navigation computer

Wiring harness

Rear-view camera

Control unit

Adapter cable

Power supply cable

Switchbox

Retrofit kit No.: 84 21 0 150 717, other part numbers see cover sheet
Installation Instructions No.: 01 29 0 300 363
Issue date: 04.2003

EN/12

8.

To install the rear-view camera and button (E46/2 up to 03/03 only)

0
0

Mark dimensions a c on the boot lid (1):


- Dimension a = 20 mm
- Dimension b = 55 mm
- Dimension c = 3 mm

Saw out the boot lid (1) in the marked area (2), deburr it
and treat the area with preservative.

a
b

c
046 1178 Z

0
0

The seal may have to be raised slightly to make the


notches visible.
Cut the seal and mounting plate E along the first notch (1)
with a knife.

Break mounting plate E and deburr it along the broken


edge.

046 1149 Z
0
0

There must be a seal between mounting plate E


and rear-view camera B.
Secure rear-view camera B on mounting plate E with
screws F.
Align rear-view camera B using the screws (1) if
necessary, at right-angles to mounting plate E.
Insert button K into mounting plate E and secure it with a
union nut (2).

039 0534 Z

0
0

Unclip the rubber cover (2) from the grab handle (1).
Cut both cables (3) on the micro switch (4).

3
4
046 1128 Z
Retrofit kit No.: 84 21 0 150 717, other part numbers see cover sheet
Installation Instructions No.: 01 29 0 300 363
Issue date: 04.2003

EN/13

8.

To install the rear-view camera and button (E46/2 up to 03/03 only)

0
0

Mark dimensions a and b on the grab handle (1):


- Dimension a = 53 mm
- Dimension b = 58 mm
Saw out the grab handle (1) in the marked area (2).

2
046 1129 Z

0
0

Mark dimensions a and b on the grab handle (1):


- Dimension a = 20 mm
- Dimension b = 14 mm

Saw out the grab handle (1) in the marked area (2).

046 1132 Z

0
0

- Dimension a = 65 mm

Mark dimensions a c on the grab handle (1):


- Dimension b = 90 mm

- Dimension c = 5 mm
File off the grab handle (1) in the marked area (2), or cut it
out with a knife.

046 1177 Z
0
0

1
2

Align mounting plate E on the grab handle (3) as follows:


- Mounting plate E in the centre between the
registration plate lights (5)

- Mounting plate seal E must be on the grab handle (3)


at the rear (2)
- Edge (4) flush with the grab handle (3)
Mark the holes (1) from mounting plate E on the grab
handle (3) and drill them with a 2.5 mm twist drill bit.

4
5

046 1130 Z

Retrofit kit No.: 84 21 0 150 717, other part numbers see cover sheet
Installation Instructions No.: 01 29 0 300 363
Issue date: 04.2003

EN/14

8.

To install the rear-view camera and button (E46/2 up to 03/03 only)

0
0

Secure mounting plate E on the grab handle (1) with


screws L.
Connect the cable (3) for the button to the open cables
(2) using miniature connector I.

2
E

I
3
046 1131 Z

0
0

Affix seal N on the grab handle (1) and affix mounting


plate E.
Fit the grab handle (1).

N
046 1183 Z

Retrofit kit No.: 84 21 0 150 717, other part numbers see cover sheet
Installation Instructions No.: 01 29 0 300 363
Issue date: 04.2003

EN/15

9.

To install the rear-view camera and button (E46/2 from 03/03 only)

0
0

Mark dimensions a c on the boot lid (1):


- Dimension a = 20 mm
- Dimension b = 3 mm

- Dimension c = 7 mm
Saw out the boot lid (1) in the marked area (2), deburr it
and treat the area with preservative.

a
b
c

046 1393 Z

0
0

The seal may have to be raised slightly to make the


notches visible.
Cut the seal and mounting plate E along the first notch (1)
with a knife.

Break mounting plate E and deburr it along the broken


edge.

046 1149 Z
0
0

There must be a seal between mounting plate E


and rear-view camera B.
Secure rear-view camera B on mounting plate E with
screws F.
Align rear-view camera B using the screws (1) if
necessary, at right-angles to mounting plate E.
Insert button K into mounting plate E and secure it with a
union nut (2).

039 0534 Z

0
0

Release the rubber cover (2) from the grab handle (1).
Pull off the grommet (3) and unclip the strain relief (4).

4
3
046 1389 Z
Retrofit kit No.: 84 21 0 150 717, other part numbers see cover sheet
Installation Instructions No.: 01 29 0 300 363
Issue date: 04.2003

EN/16

9.

To install the rear-view camera and button (E46/2 from 03/03 only)

0
0

- Dimension a = 53 mm

Mark dimensions a and b on the grab handle (1):


- Dimension b = 58 mm
Saw into the grab handle (1) in the marked area (2).

2
046 1390 Z

0
0

Remove the outer part (1) of the grab handle (2).


Do not damage the seal and the cables inside. Max.
depth of cut 2 mm.
Saw into the grab handle (2) in the marked area (3) along
the exterior shell (4).

4
046 1391 Z

0
0

Remove the inner part (1) of the grab handle (4) and the
plate (2).
Cut through both cables (6) directly at the microswitch
(3).

Remove the mounting (5).

6
046 1392 Z

0
0

- Dimension a = 65 mm

Mark dimensions a c on the grab handle (1):


- Dimension b = 90 mm

- Dimension c = 3 mm
File off the grab handle (1) in the marked area (2), or cut it
out with a knife.

2
046 1177 Z

Retrofit kit No.: 84 21 0 150 717, other part numbers see cover sheet
Installation Instructions No.: 01 29 0 300 363
Issue date: 04.2003

EN/17

9.

To install the rear-view camera and button (E46/2 from 03/03 only)

0
0

- Mounting plate E in the centre between the


registration plate lights (5)

Align mounting plate E on the grab handle (3) as follows:

- Mounting plate seal E must be on the grab handle (3)


at the rear (2)
- Edge (4) flush with the grab handle (3)
Mark the holes (1) from mounting plate E on the grab
handle (3) and drill them with a 2.5 mm twist drill bit.

4
5

046 1130 Z

0
0

Secure mounting plate E on the grab handle (1) with


screws L.
Connect the cable (3) for the button to the open cables
(2) using miniature connector I.

2
E

I
3
046 1131 Z

Retrofit kit No.: 84 21 0 150 717, other part numbers see cover sheet
Installation Instructions No.: 01 29 0 300 363
Issue date: 04.2003

EN/18

10. To install the rear-view camera and button (E46/4 only)


0
0

Mark dimensions a and b on the boot lid (1):


- Dimension a = 20 mm
- Dimension b = 5 mm

Saw out the boot lid (1) in the marked area (2), deburr it
and treat the area with preservative.
a

046 1136 Z

0
0

The seal may have to be raised slightly to make the


notches visible.
Cut the seal and mounting plate E along the first notch (1)
with a knife.

Break mounting plate E and deburr it along the broken


edge.

046 1149 Z
0
0

There must be a seal between mounting plate E


and rear-view camera B.
Secure rear-view camera B on mounting plate E with
screws F.
Align rear-view camera B using the screws (1) if
necessary, at right-angles to mounting plate E.
Insert button K into mounting plate E and secure it with a
union nut (2).

039 0534 Z

0
0

Unclip the rubber cover (2) from the grab handle (1).
Cut both cables (3) on the micro switch (4).

3
4
046 1128 Z
Retrofit kit No.: 84 21 0 150 717, other part numbers see cover sheet
Installation Instructions No.: 01 29 0 300 363
Issue date: 04.2003

EN/19

10. To install the rear-view camera and button (E46/4 only)


0
0

Mark dimensions a and b on the grab handle (1):


- Dimension a = 53 mm
- Dimension b = 58 mm
Saw out the grab handle (1) in the marked area (2).

2
046 1129 Z

0
0

Mark dimensions a and b on the grab handle (1):


- Dimension a = 27 mm
- Dimension b = 22 mm

Saw out the grab handle (1) in the marked area (2).

046 1132 Z

0
0

- Dimension a = 65 mm

Mark dimensions a c on the grab handle (1):


- Dimension b = 90 mm
File off the edge of the grab handle (1) in the marked area
(2), or cut it out with a knife.

2
046 1140 Z

0
0

1
2

Align mounting plate E on the grab handle (3) as follows:


- Mounting plate E in the centre between the
registration plate lights (5)

- Mounting plate seal E must be on the grab handle (3)


at the rear (2)
- Edge (4) flush with the grab handle (3)
Mark the holes (1) from mounting plate E on the grab
handle (3) and drill them with a 2.5 mm twist drill bit.

4
5

046 1130 Z

Retrofit kit No.: 84 21 0 150 717, other part numbers see cover sheet
Installation Instructions No.: 01 29 0 300 363
Issue date: 04.2003

EN/20

10. To install the rear-view camera and button (E46/4 only)


0
0

Secure mounting plate E on the grab handle (1) with


screws L.
Connect the cable (3) for the button to the open cables
(2) using miniature connector I.

2
E

I
3
046 1131 Z

0
0

Mark dimensions a and b on seal N of the grab handle (1):


- Dimension a = 20 mm

- Dimension b = 5 mm
Cut out the marked area (2) of seal N.
a

N
046 1135 Z

0
0

Affix seal N on the grab handle (1) and affix mounting


plate E.
Fit the grab handle (1).

N
046 1183 Z

Retrofit kit No.: 84 21 0 150 717, other part numbers see cover sheet
Installation Instructions No.: 01 29 0 300 363
Issue date: 04.2003

EN/21

11. To install and connect the control unit


0
0

Connect the connection plug (1) of the rear-view camera


and branch A1 onto control unit C.
The switch-off delay (5 seconds) of the rear-view
camera can be deactivated as follows.

Cut through the cable loop (2), violet/black cable,


and insulate both ends.

A1

046 1225 Z

0
0

Affix protective strip J to control unit C.


Cut off any excess lengths.

C
J

053 0541 Z
0
0

Use cable tie G to attach control unit C to the web of the


boot lid (1).

C
C

039 0371 Z

Retrofit kit No.: 84 21 0 150 717, other part numbers see cover sheet
Installation Instructions No.: 01 29 0 300 363
Issue date: 04.2003

EN/22

12. To install and connect the wiring harness (cars with TV function only)
0
0

A2

Use miniature connector I to connect branch A2 to the


blue/yellow cable from plug X328 (PIN 1).
Thread wiring harness A through the cable grommet (1)
into the boot.

X328
A
1
046 1227 Z
0
0

Lay wiring harness A to the left-hand side of the boot and


secure it to cable tie holders M with strips of adhesive
tape H.

Insert cable tie holder M into the rear closing panel (1).

H
1
046 1230 Z

0
0
0

GPS NAVIGATION SYSTEM

Route wiring harness A to the video module (1).


Remove the insertion tool.
Insulate branch A3, green cable, and branch A9, white
cable, and tie them back.

Connect branches A4 and A5 to natural coloured plug


X18806 as follows:

X18806
X18804

A3-A9
046 1347 Z

- Branch A4, transparent cable, in PIN 13


- Branch A5, black/brown cable, in PIN 14
Connect branches A6 A8 into blue plug X18804 as
follows:
- Branch A6, black cable, in PIN 17
- Branch A7, red cable, with miniature connector I to
the red/green cable (PIN 1)
- Branch A8, brown cable, with miniature connector I to
brown cable (PIN 10)

Retrofit kit No.: 84 21 0 150 717, other part numbers see cover sheet
Installation Instructions No.: 01 29 0 300 363
Issue date: 04.2003

EN/23

13. To install the switchbox (cars without TV function only)


0
0

Enlarge the holes (1) in switchbox Q with an 8 mm twist


drill bit.
Position speed nuts S.

046 1238 Z

0
0

- Dimension a = 53 mm

- Dimension b = 140 mm

Mark dimensions a d on the side panel (1):

- Dimension c = 15 mm
- Dimension d = 15 mm

Drill through the side panel (1) at the drilling positions (2)
using an 8 mm twist drill bit.

046 1239 Z
0
0

Insert switchbox Q behind the side panel (1) and secure it


with hexagonal screws T.

T
Q

046 1240 Z
0

Retrofit kit No.: 84 21 0 150 717, other part numbers see cover sheet
Installation Instructions No.: 01 29 0 300 363
Issue date: 04.2003

EN/24

14. To install and connect the wiring harnesses (cars without TV function only)
0
0

A2

Use miniature connector I to connect branch A2 to the


blue/yellow cable from plug X328 (PIN 1).
Thread wiring harness A through the cable grommet (1)
into the boot.

X328
A
1
046 1227 Z
0
0

Route wiring harness A to the left-hand side of the boot


and secure it to cable tie holders M with strips of adhesive
tape H.

Insert cable tie holder M into the rear closing panel (1).

H
1

046 1230 Z
0
0

Route wiring harness A to the left side of the boot.


Remove the insertion tool.

046 1366 Z
0
0

A3-A9

Insulate branch A3, green cable, and branch A9, white


cable, and tie them back.
Connect branches A4 A6 to branch P1 as follows:
- Branch A4, transparent cable, in PIN 24
- Branch A5, black/brown cable, in PIN 11
- Branch A6, black cable, in PIN 23

P1

046 1352 Z
Retrofit kit No.: 84 21 0 150 717, other part numbers see cover sheet
Installation Instructions No.: 01 29 0 300 363
Issue date: 04.2003

EN/25

14. To install and connect the wiring harnesses (cars without TV function only)
0
0

P3

A7-A8

Connect branches A7 and A8 to branch P1 as follows:


- Branch A7, red cable, with miniature connector I to
branch P3, red cable
- Branch A8, brown cable, with miniature connector I to
branch P4, brown cable

P4

P1

I
046 1364 Z
0
0

Connect branches O3 and O4 to branch P1 as follows:


- Branch O3, red/yellow cable, in PIN 26
- Branch O4, brown cable, in PIN 13

O3
O4

P1
046 1321 Z

0
0

P1

Connect branches O5 and P1 to switchbox Q.


Fit edge protectors V to any potential chafing points.

O5

V
046 1286 Z
0
0

Disconnect blue plug X1313 on the navigation computer


(1).
- Connect branch O2 to plug X1313
- Connect branch O1 to the navigation computer (1)

O2
O1

Install the navigation computer (1).

X1313

046 1287 Z

Retrofit kit No.: 84 21 0 150 717, other part numbers see cover sheet
Installation Instructions No.: 01 29 0 300 363
Issue date: 04.2003

EN/26

14. To install and connect the wiring harnesses (cars without TV function only)
0
0

GPS NAVIGATION SYSTEM

Route branch P2 to the radio receiver (1).


Disconnect plug X13646.
Use miniature connector I to connect branch P2 to the
violet/white cable of plug X13646 (PIN 16).

P2

I
X13646
046 1288 Z

Retrofit kit No.: 84 21 0 150 717, other part numbers see cover sheet
Installation Instructions No.: 01 29 0 300 363
Issue date: 04.2003

EN/27

15. Concluding work


The rear-view camera retrofit does not require coding.
0

- Connect the battery


- Conduct a brief test
Check the function of the rear-view camera as follows:
- Switch on the ignition
- Engage reverse; an image must appear on the on-board monitor
- Disengage reverse gear
If you have cut through the violet/black cable loop on the control unit, the on-board monitor must change over
immediately.
If you did not cut through the violet/black cable loop on the control unit, the on-board monitor must change
over after about 5 seconds
- Re-assemble the car

Retrofit kit No.: 84 21 0 150 717, other part numbers see cover sheet
Installation Instructions No.: 01 29 0 300 363
Issue date: 04.2003

EN/28

16. Circuit diagram (cars with TV function only)


0

A1*

0,50 VI/SW

0,25 WS

TA

RFS

Video-

Video+

12

0,75 GN

0,75 BR

0,75 RT

RSF inv

0,25 SW

1
31

2
30

X1*

17

13

X18804

Video-

10

Video+

RSF inv

31

30

X5*

0,75 GN

0,75 GN

0,35 SW/BR

0,14 transparent

X2*
X3*

X4*

14

X18806

A197
046 1345 Z
0

Legend
A1*

X3*

Socket contact

X4*

Control unit

Cable open

A197

Video module

X5*

Cable open

X1*

Black 12-pin plug

X18804

Blue 18-pin plug

X2*

Cable loop

X18806

Natural colour 18-pin plug

All the designations marked with an asterisk (*) apply only to these installation instructions or this circuit diagram

Cable colours
BL

Blue

RT

Red

BR

Brown

SW

Black

GE

Yellow

VI

Violet

GN

Green

WS

White

Retrofit kit No.: 84 21 0 150 717, other part numbers see cover sheet
Installation Instructions No.: 01 29 0 300 363
Issue date: 04.2003

EN/29

N9

16

16

X3*

0,50 VI/WS

X4*

RFS

0,75 GN

0,75 GN
R

10

X5*

A1*

12

10

12

Video -

31

11
Video -

Video +

30

x x

0,35 SW/BR

K-Bus

24
Video +

25
30

31

12

31

23
RSF inv

RSF inv

X1*

0,50 BR/SW

0,50 WS/GR/GE

0,75 BR

0,75 RT/GE

18

30

26

NAVNF- NAVNF+ 30

0,75 GE/SW

0,75 GE/BR

X1313

30

18

NAVNF+ NAVNF-

31

13

10

31

0,75 RT/GE
0,75 RT/GE

VMCL31

0,14 transparent

15

0,75 RT
0,75 RT

TA

0,75 BR
0,75 BR

14

0,25 WS

X13646

0,25 SW

Retrofit kit No.: 84 21 0 150 717, other part numbers see cover sheet
Installation Instructions No.: 01 29 0 300 363
Issue date: 04.2003

X2*

0,75 BR
0,75 BR

A112
12

VMCL31

A2*

X6*

K-Bus

X7*

0,35 SW
18

0,35 SW
NAVB NAVB31

0,35 WS
17

0,35 SW
NAVG NAVG31

0,35 GN
16

0,35 SW
NAVR NAVR31

5
NAVB NAVB31

13

15

NAVB NAVB31

0,35 GN

NAVB 31

0,35 SW

NAVB
5

4
NAVR NAVR31

15

16

046 1289 Z

NAVG NAVG31

14

14

NAVG NAVG31 NAVR NAVR31

0,35 WS

NAVG31

0,35 SW

NAVG

0,35 SW

NAVR31

0,35 SW

NAVR

17. Circuit diagram (cars without TV function only)

EN/30

0,50 VI/SW

17. Circuit diagram (cars without TV function only)


0

Legend
A1*

Control unit

A2*

Switchbox

A112

Navigation computer

N9

Radio receiver

X1*

Black 12-pin plug

X2*

Cable loop

X3*

Socket contact

X4*

Cable open

X5*

Cable open

X6*

Black 26-pin plug

X7*

Natural colour 18-pin plug

X1313

Blue 18-pin plug

X13646 Black 16-pin plug


All the designations marked with an asterisk (*) apply only to these installation instructions or this circuit diagram

Cable colours
BL

Blue

BR

Brown

GE

Yellow

GN

Green

GR

Grey

RT

Red

SW

Black

VI

Violet

WS

White

Retrofit kit No.: 84 21 0 150 717, other part numbers see cover sheet
Installation Instructions No.: 01 29 0 300 363
Issue date: 04.2003

EN/31

Вам также может понравиться