Академический Документы
Профессиональный Документы
Культура Документы
Number of stages Customer Item number Service Flowserve reference Date : : : : : dargroup Default 0.1 February 27, 2014 Capacity Head Specific gravity Pump speed Test tolerance
: 08EML : EC-2363 : 19 : : : : : 10.6 l/s 100.00 m 1.000 1480 rpm Hydraulic Institute Level A
CURVES ARE APPROXIMATE, PUMP IS GUARANTEED FOR ONE SET OF CONDITIONS; CAPACITY, HEAD, AND EFFICIENCY.
Bowl performance shown below is corrected for materials, viscosity and construction.
Bowl head of 100.12 m corresponds with 100.0 m head at discharge flange adjusted for elevation and friction losses.
FlowSelex v2.2
1 of 5
Hydraulic Datasheet
Customer Customer reference Item number Service : dargroup : Default : : Operating Conditions Capacity Water capacity (CQ=1.00) Normal capacity Total Developed Head Water head (CH=1.00) NPSH available (NPSHa) NPSHa less NPSH margin Maximum suction pressure Rated suction pressure : : : : : : : : : 10.6 l/s 100.00 m Ample 0.0 kPa.g 0.0 kPa.g Material column code Pump / Stages Based on curve no. Flowserve reference Date : : : : 08EML EC-2363 Default 0.1 February 27, 2014 / 19
Materials / Specification : B30 Other Requirements Hydraulic selection : No specification Construction : No specification Test tolerance : Hydraulic Institute Level A Driver Sizing : Max Power(MCSF to EOC)with SF
Liquid Liquid type Liquid description Temperature / Spec. Gravity Viscosity / Vapor pressure : Other : : 16 C : 1.0 cP
/ 1.000 / Performance
Pump speed : 1480 rpm NPSH required (NPSHr) : 0.8 m Hydraulic power : 10.4 kW Efficiency (CE=1.00) : 78.9 % Power: (Rated / Max) : 13.2 kW / 13.4 kW Driver power : 14.9 kW / 20.0 hp Bowl Pressure : 1449.1 kPa.g (based on shut off and Rated specific gravity @ Cut dia) Maximum allowable : 3674.9 kPa.g Bowl & column hydrotest : 1811.3 kPa.g Dischg Head Dischg Region MAWP : 1965.0 kPa.g Suction Regions MAWP : 1965.0 kPa.g
Impeller diameter
: Rated / Maximum / Minimum : 152.8 ... 156.0 mm 146.0 mm Impeller dia ratio (rated/max) : 98.0 % Maximum head @ rated dia : 147.98 m Head rise to shut off : 47.8 % Total head ratio (rated/max) : 95.2 % Flow at BEP : 11.2 l/s Flow as % of BEP : 94.4 % Minimum continuous flow : 3.8 l/s Suction specific speed : 8930 US units Thrust - Rated flow / Rated suction : 4776.8 N Max thrust - Shut off / Rated suction : 6767.5 N Min thrust - Runout flow / Max Suction : 3166.5 N (A negative thrust value indicates an upthrust condition)
CURVES ARE APPROXIMATE, PUMP IS GUARANTEED FOR ONE SET OF CONDITIONS; CAPACITY, HEAD, AND EFFICIENCY. Bowl performance shown below is corrected for materials, viscosity and construction.
Bowl head of 100.12 m corresponds with 100.0 m head at discharge flange adjusted for elevation and friction losses.
FlowSelex v2.2
2 of 5
Construction Datasheet
Customer Customer reference Item number Service : dargroup : Default : : Pump Pump / Stages / Stages Based on curve no. Flowserve reference Date : 08EML : EC-2363 : Default 0.1 : February: 27, 2014 27, 2014 February Driver Information : : 20.0 hp / 14.9 kW : : : : / 19
Construction Bowl construction / lined : Threaded / Lined bowls Impeller type : Semi-open & closed impellers Impeller fastening : Colleted Column construction : Column flange spec'n : Taneytown Specification Column dia (nominal) : 101.6 mm Column pipe length : 0.23 m Column section length : 2743.2 mm Lineshaft brg spacing : 2743.2 mm Lineshaft diameter : 31.7 mm Lineshaft coupling type : Threaded coupling Lineshaft bearings, qty : 1 Lineshaft construction : Lineshaft lubrication : Disch size/rating/face : 4.00 in //"TF" - Fab'd / Above grade Suct and Dischg Thrust Stand Size : -
Manufacturer Power / SF (Req' / Act') Vertical shaft type Driver Type Frame size / Base dia Enclosure Duty type Efficiency type Hazardous area class Explosion 'T' rating Volts / Phase / Hz Amps-full load/locked rotor Motor starting Insulation Temperature rise Bearings / Lubrication Motor mounted by Motor Thrust rating down/up
1.0
: : : : : : : : : :
/-
Bowl Impeller Bowl bearing Bowl shaft Bowl wear ring Impeller wear ring Column Lineshaft Bearing retainer Lineshaft bearing Lineshaft sleeve Discharge head Support plate
: : : : : : : : : : : :
Arrangement Size Manufacturer / Type Material code (Man'f/API) Gland material Auxiliary seal device Seal flush plan Seal flush construction
//-
: : : Additional information
Complete pump Mounting plate Driver(nett) Hydrostatic test Performance test NPSH test
Pit / sump depth : Pump length : 3.53 m mounting surface to bell/strainer bottom Available well diameter : Max dia below mtg surface : 190.5 mm
Notes -
FlowSelex v2.2
3 of 5
All dimensions are in millimeters unless otherwise specified Customer Item number Service Customer PO # Flowserve reference : dargroup : : : : Default 0.1 Pump size & type Pump speed / Stages Flow / Head Driver power / Frame Volts / Phase / Hz : 08EML : 1480 rpm / 19 : 10.6 l/s / 100.00 m : 14.9 kW / 20.0 hp / : -/0/Drawing number Date Certified by / Date : Seal type Seal flush plan : : February 27, 2014 : : : FlowSelex v2.2
4 of 5
Pump size & type Based on curve no. Number of stages Capacity Head : 10.6 l/s : 100.00 m Specific gravity Pump speed : 1.000 : 1480 rpm
: 08EML : EC-2363 : 19
FlowSelex v2.2
5 of 5