Академический Документы
Профессиональный Документы
Культура Документы
For 60, 88,168, 816 (wwo) integrations are via a TTL link to com port 1 on the Texecom panel WebWayOne cable 05-0246 is required for installation 412,816 (Std),832 are via a webway modem capture module (22-5059) For Wintex programming via a PC a USB Com cable (Texecom part no JAA-0001 or JAC-0001). Texecom TTL Cable 05-0246 (5 Pin)
Texecom Compatibility List Panel Variant Connection Type Install Guide Premier 24 Modem Capture Pg 5 Premier 48 Serial TTL Pg 6/7 Premier 60 Serial TTL Pg 2/3 Premier 88 Serial TTL Pg 2/3 Premier 168 Serial TTL Pg 2/3 Premier 412 Modem Capture Pg 5 Premier 816 Serial TTL Pg 4 (WWO Version) Premier 816 Modem Capture Pg 5 Modem Capture Serial TTL Serial TTL Pg 5 Pg 6/7 Pg 6/7 Texecom
Pin 2 from right
Premier 832 Premier Elite 24 Premier Elite 48 WebWay SPT T - Red R - Green RTN - Blue
Automatic SIA 3 with text enriched messages
All alarms generated by the Alarm System are automatically sent to the AMS using SIA. SIA messages provide a full audit trail of an event which detector, location, time and date, and a permanent record of every alarm. Messages for set and unset include who, where, time, and date, all recorded. No need to check that each PIN is correctly wired; the Texecom and the WebWay take care of everything automatically.
Com Port 1
The wiring above refers to the WebWay part 05-0246 Other cables can be used, please note the pin details above. Connect the WebWay PWR + and - to any relevant Power (+12V/+24V) and Ground (0V) terminals.
1
www.webwayone.co.uk sales@webwayone.co.uk 01635 231500
Texecom Series
Texecom Premier 88/168/60 Series
The Texecom panel configuration is uploaded via the Wintex software and downloaded to the panel on com port 2 from a local PC. The following requires configuring in the panel, Communications Menu In Options 1. Enable communicator must be ticked 2. UDL passcode (set in the panel) must match. 3. Dial attempts 1, ring before answer 3 In ARCs 1. Account number (site ID) 2. SIA Level 2/3 3. Connect Via IP - ticked 4. Send SIA text ticked In Radio-Pad and Com Port options 1. Com Port 1 WebWayOne module 2. Local IP address 127.0.0.1 3. Local IP port 50561 4. Gateway 127.0.0.1 5. Subnet Mask 255.255.255.0 6. Name/SMG port 50561
Important: The WebWay should be connected to Com port 1. If you wish to use Com port 2 on a Premier 88 panel then please contact Texecom for a 5 to 7 pin Molex converter.
Wintex Settings
Important: The WebWay SPT should be connected to Com port 1. All settings are configured with the Wintex Communications menu (7th option down on the left side of the Wintex program labeled Comms). This can be configured on a local PC plugged on to Com Port 2 with the WebWay unit running on Com Port 1. (In keypad settings leave Com Port 2 as unassigned, when the PC cable is connected it will automatically detect and allow you to configure settings).
Texecom Series
Texecom Premier 88/168/60 Series
Account No: should match the ARC Site/Chip ID and tick the relevant trigger event boxes relevant to the premises.
If the SMS call centre is utilised the engineer should enter the appropriate number and it should be configured under: UDL/Digi Options Radio/SMS Option SMS Centre Pri. The SMS centre telephone number is used to send SMS text messages to mobile phones. (Default = 07860980480). Note if the Texecom is being programmed with a laptop on com port 2 and the WebWay is connected to com port 1 the SPT will be lost from the panel until the Wintex session is closed.
3
www.webwayone.co.uk sales@webwayone.co.uk 01635 231500
Texecom Series
Texecom Premier 816 (WWO Version)
A special version of the 816 known as the Premier 816 WWO is shipped with special software which allows it to communicate with the 2424 SPT, however it does not have a dialer which means that it can only be used with the 2424 system. Note that a cable assembly is required , which WebWayOne can supply although any 5-Way Molex type connecter can be modified. The Texecom main board assembly has only 1 Com port on the PCB with a 5-pin connection interface. This connects to the TTL R, T and gnd terminals of the WebWayOne 2424 panel interface. This means that a local PC and the 2424 SPT cannot be connected to the panel at the same time. When connecting the local PC, leave the SPT disconnected for about 30 seconds before connecting to the PC. This should ensure that the panel recognizes that the SPT has been disconnected. If there are problems establishing communications with the local PC, try entering user code + menu + 7 on the panel keypad (abort all communications). The connection details are as follows:
Texecom
Pin 2 from right
Com Port 1
The wiring above refers to the WebWay part 05-0246 Other cables can be used, please note the pin details above.
5: Enable Test Transmission OPTIONAL 6: Enable Cancel Call Waiting DISABLED 7: Enable Backup to ARC 8: Enable Blind Dialing DISABLED DISABLED
Texecom Series
Texecom Premier 24 (Modem Capture Only), 412,816 (Standard Edition),832
The following models are integrated via a modem capture module, provided by WebWay. This type of integration does not support Upload/Download functionality.
The modem capture board needs wiring as follows to the Texecom panel.
Texecom T R
5: Enable Test Transmission OPTIONAL 6: Enable Cancel Call Waiting DISABLED 7: Enable Backup to ARC 8: Enable Blind Dialing DISABLED ENABLED
Texecom Series
Texecom
Pin 2 from right Pin 1 for right Pin 3 from right
Com Port 1
Wintex Programming
Simple Configuration can be achieved with Texecoms Wintex program and a suitable comms cable. To allow communications simply connect the cables to com port two on the device and then Config a account as usual with the following settings in comms. (In keypad settings leave Com Port 2 as unassigned, when the PC cable is connected it will automatically detect and allow you to configure settings).
In options
Enable Communicator must be ticked
Texecom Series
Texecom Premier Elite 24/48 & Premier 48
Radio Pad and Com port settings
Ensure Com Port 1 is set to WebWayOne/Emizon Module
Also set the following; Local IP Address 127.0.0.1 Local IP Port 50561 Gateway 127.0.0.1 Subnet Mask 255.255.255.0 Name/SMG Port 50561 Finally send the update back to the panel.
General troubleshooting tips for Texecom panels We recommended that all Texecom installs are completed with Wintex software. Once you have completed programming the Texecom then restart the panel and WebWay the Texecom bus requires this reboot to see the WebWay as a communications module. Alternatively change the com port settings and move the WebWay to com Port 2. If you receive the following message on the keypad; ATS path fail com 1 this refers to a actual communication path. Please check your Ethernet/GPRS/PSTN connectivity. This does not refer to the com bus between the panel and the WebWay unit. To stop this alarm being sent to the keypad, select Areas > Options > ATS Path Faults and make sure that no areas are selected. Testing alarms, you can send a PA from the keypad by pressing 1 & 3 at the same time. If you wish to use com port 2 on a premier 88, please contact Texecom for a 5 to 7 pin converter or see the pin out on page 2