Академический Документы
Профессиональный Документы
Культура Документы
PRACTICE QUESTIONS
GRAPHICS
These questions have been taken from official syllabus for PYP-004 and contribute to the preparation for Theory Test and also for Final Examination.
M.B. Ahmed
Lecturer, CASS, KFUPM 1/12/2014
1
Lectures Plan
First Lecture Objectives
Introduction to Graphics & Engineering Drawing The concept of views Orthographic Projection Concept of Hidden Lines Exercises in the book (page numbers: 05-12)
INSTRUCTIONS:
These questions are lecture-wise arranged. Students should attempt the questions under LECTURE ONE heading after first week and so on. In the end there are solved exercises. All the questions in this file are important for Theory Test and also helpful for Final Exam
ANS__________ 6. How many hidden lines will be drawn in front view of the object shown in Figure 01? a. one b. two c. Four d. None
7. How many hidden lines will be drawn in Right End Elevation view of the object shown in Figure 02? a. Four b. One c. Two d. Six 8. Name the Orthographic projection view a in fig-03? a. Plan b. Front c. R.H End Elevation d. L.H End Elevation
9. How many hidden lines will be drawn in the top view of the object shown in above figure? a. 2 b. 4 c. 6 d. No hidden lines will be drawn
10. In the adjacent figure, the front view dimensions are--------------? a. 80, 40, 10, 20 b. 40, 20, 30 c. 80, 20, 10, 05 d. 10, 20,70, 60
a. Perspective b. Orthographic c. Isometric 14. In the front view of figure (Q:15), the hole feature will be shown as _____. a. Continuous lines b. Hidden Lines c. Broken Lines
15. In third angle of projection, the front view of an isometric projection is projected on ____ plane a. Front b. Side c. Top
16. What type of drawing is it? a. Isometric b. Orthographic c. Isobaric d. None of above
17. What is the angle of projection, for the adjacent figure? a. First Angle b. Second Angle c. Third Angle d. None of above
18. Which dimensions will be used for rectangular cut on the base of figure-04? a. 15-35-120-15 b. 15-50-15-50 c. 35-120-35-120
19. How many hidden lines will be drawn in the top view of the object shown in above figure? a. 2 b. 4 c. 6 d. No hidden lines will be drawn
21. Drafting Settings dialogue box can be accessed using _____________ a. Tools Menu b. Format Menu c. Edit Menu 22. Always use __________ to pick dimension line origins. a. Ortho Mode b. Snap c. Osnap 23. To print drawings we should use ______ space a. Model b. Paper
24. You can quickly open an existing document using ------tool bar a. Standard b. Menu c. Property
10
25. Which of the following can be drawn using Object Property Tool Bar a. Circle b. Rectangle c. Hidden Line 26. Which of the following mode you would use to pick the dots on regular grids? a. OSNAP b. SNAP c. ORTHO 27. In Auto-CAD object snap is used to pick accurately--------------of a line. a. End point b. Mid point c. Nearest point d. All of above 28. Format and Tools Buttons lie on ------Tool Bar a. Menu b. Standard c. Property 29. The value of drawing units is determined before you draw. a. True b. False 30. Regular pattern of dots displayed on the screen and acting as a visual aid are called______ a. Drawing Units b. Drawing grid 31. In Orthographic projection, projection lines are ------------ to image plane. a. parallel b. perpendicular c. at 45 degrees 32. In orthographic projection, the perpendicular distance between the views 11
is________ a. 10 mm b. 20mm c. Same 33. In AutoCAD user interface, ________ displays prompts and messages. a. Command Window b. Drawing Area c. Standard Tool Bar 34. In AutoCAD, Ortho command is used to draw --------------lines. a. Perpendicular b. Inclined c. Polyline d. All of above 35. Which of the following pairs are found on Status Bar a. Snap and Grid b. Units and Limits c. Dimension and Text 36. _______ is used to change the line type. a. Standard Tool Bar b. Property Tool Bar c Format Tab
12
37. What does this icon represent? a. Rectangle b. Line c. Parallelogram 38. Name the AutoCAD tool bar where you find the hidden Line Types? a. Draw Toolbar b. Modify Toolbar c. Command Line d. Object Properties Toolbar 39. In AutoCAD, a polyline can be drawn by: a. Draw Tool bar b. Modify tool bar c. Object properties tool bar 40. In AutoCAD, a circle can be drawn by a. centre, radius b. Centre Diameter c. Start, centre, end d. 3 points e. All of the above 41. After starting circle command, _______ should be specified first. a. Radius of circle b. Diameter of circle c. Centre point of circle
13
42. In AutoCAD, an arc can be drawn by the following command: a. Start, End, Radius b. Start, End, Direction c. Three Points d. All of above 43. Draw Commands can be started by _____ ways a. one b. Two c. Three 44. Which command would you use to draw connected sequence of many line segments with different thickness? a. Continuous Line Command b. Multi Line Command c. Polyline Command 45. The _____ command is used to dimension along straight lines. a. DIMDIAMETER b. DIMALIGNED c. DIMLINEAR
14
46. AutoCAD draw tool bar symbol a. Pentagon b. Rectangle c. Array d. Construction line
47. Fillet command can be started using draw-toolbar a. True b. False 48. Identify the following symbol, found in modify tool bar. a. Offset b. Scale c. Mirror d. Cloud 49. Which command can be started using this icon? a. Offset b. Trim c. Fillet 50. What does this icon represent? a. Circle b. Polygon c. Ellipse 51. Which tool bar does this icon lie on? a. Draw tool bar b. Modify tool bar
15
c. None of these 52. What does this icon represent? a. Extend b. Copy c. Mirror 53. Offsetting and copying the same circle will give same result a. True b. False 54. R.H End Elevation can be used to have L.H End elevation by using_______command a. Copy command b. Mirror Command c. Copy Command 55. Which of the following command can be used to create one or more duplicates of any drawing objects? a. Mirror Command b. Copy Command c. Offset Command 56. Cutting edge must be defined while using______ command a. Erase Command b. Trim Command c. Extend Command 57. What does this AutoCAD symbol represent? a. Inclined b. Chamfer c. Fillet d. Radius 58. Which command can be started using this icon? a. Offset b. Trim 16
c. Extend 59. The ________command is useful for drawing symmetrical objects a. Offset Command b. Mirror Command c. Copy Command 60. What does this AutoCAD icon represent? a. Arc b. Spline c. Polyline d. Rotate
61. Write the names of the commands these tabs are used for: LINE COMMAND ERASE COMMAND
62. Which of the following command you would use to create two concentric circles a. Mirror
17
b. Copy c. Offset 63. The corners of rectangular shapes can be rounded by using a. Chamfer Command b. Move Command c. Fillet Command 64. To select a number of objects for modification which method is the quickest one? a. Picking method b. Window selection
18