Академический Документы
Профессиональный Документы
Культура Документы
Description
The TB820 ModuleBus Modem is a communication interface for connection of S800 I/O modules via the optical and electrical ModuleBus. The module can not handle High Integrity I/O modules (AI880, DI880 and DO880). The TB820 can be used in both a simplex optical configuration as well as in a duplex optical configuration. In a simplex configuration, the optical ModuleBus nodes are connected in a ring. In a duplex configuration, the optical ModuleBus nodes are connected in a row.
L+ LSA SB
TB820 V2 CLUSTER 4 56 3 7 2 1
TB820 has two basic parts: Module termination board and the power supply/communications board (see block diagram). The termination board is a unit where most of the connections to the outside takes place. It is grounded to the DIN rail through a metallic spring connector. The board carries screw terminals for power supply and redundant power supply monitoring, connector for the electrical ModuleBus, a current limit fuse for the +24 V supply of the I/O modules and the electrical ModuleBus.
3BSE020923R5021
235
Description
Appendix C Specifications
The power supply board has an isolated power converter that generates a short circuit proof +5 V supply for the TB820 and connected I/O modules. This board also contains the ModuleBus interfaces, LED indicators and one screwdriver maneuvered rotary switch for the ModuleBus I/O cluster address. The ModuleBus I/O cluster address (1-7) is set by a rotary decimal code switch, any other value than 1-7 is not allowed and will turn the Run LED off. The ModuleBus has an electrical and an optical interface which are logically the same bus. A maximum of twelve I/O modules can be connected to the electrical ModuleBus and up to seven clusters can be connected to the fiber optic ModuleBus expansion. The fiber-optical interface is intended for local distribution of I/O clusters and where more than 12 I/O modules per station are required. Any distribution of I/O modules across the base cluster and the remote cluster(s) is allowed, however not more than 24 I/O modules per station can be used. The module is equipped with optical Transmitter/Receiver for up to 10 Mbit/s. Both plastic and HCS (Hard Clad Silica) optic fiber with connectors (Agilents, former Hewlett-Packard, Versatile Link) can be used with TB820.
236
3BSE020923R5021
Appendix C Specifications
Technical Data
Technical Data
Table 54. TB820 ModuleBus Modem Specifications
Item Power input Power consumption at 24V d.c. Power dissipation Power supply monitoring inputs Value 24 V d.c. (19.2 - 30) 100 mA 6.0 W Max. input voltage: 30V Min. input voltage for high level: 15 V Max. input voltage for low level: 8 V 24 V max. = 1.4 A 5 V max. = 1.5 A Electrical ModuleBus Optical ModuleBus Maximum of 12 I/O modules Maximum of 7 I/O clusters
Fiber optic interface, two transmitters and two receivers for Max. 10 Mbit/s Wavelength 650 nm Maximum ambient temperature 55oC/(131 F)
3BSE020923R5021
237
Technical Data
Appendix C Specifications
238
3BSE020923R5021
Appendix C Specifications
Connections
58 mm (2.3)
122 mm (4.8)
R P
ORx1
ORx2 ERx
170 mm (6.7)
CLUSTER 4 5 6 3 7 2
TB820
L L+L- + - SAB L+ SA SB
Connections
Table 55. Power Supply Connections TB820/TB820V1
Designation L+ L+ SA LDescription +24 V d.c. Supply In +24 V d.c. Supply Out Redundant Power Supply A Monitoring Input 0 V d.c. Supply In
3BSE020923R5021
239
Connections
Appendix C Specifications
240
3BSE020923R5021
Appendix C Specifications
Opto connectors type Agilents, former Hewlett-Packard, Versatile Link can handle both plastic and HCS optic fiber.
Hard Clad Silica (HCS) fiber up to 200 meters. Riser or plenum. Simplex or duplex cable. Latching simplex or duplex connector. Cable attenuation maximum 2 dB.
3BSE020923R5021
241
Appendix C Specifications
X2
MBI-4
0V
DC DC
DIN-rail
SB L-
POS(9:7) SA L+
X1B 3 2 1
E O
E O
E O
E O
X5
TB820-2
X4
242
3BSE020923R5021